APC Mobile Power Pack, 10Wh
Contents
1. www apc com Mobile Power Pack UPB10 User s Manual Introduction Thank you for purchasing APC s 10Whr Mobile Power Pack UPB10 The UPB10 is a rechargeable battery pack that is ideal for powering and charging iPods MP3 players mobile phones and portable gaming systems via USB Charging Cables This user manual provides operating instructions for the UPB10 Please read the entire user manual prior to use Register this purchase online at Wwww apc com Features e Slim lightweight Lithium Polymer design e Four LED status indicators e Compatible with APC s TravelPower Adapter and Universal Power products for charging e Up to 8 Watts continuous power and 10 Watts peak power output Inspection Check the package contents for the following items e 10Whr Mobile Power Pack UPB10 e USB Mini B Cable e User s Manual e 5 Volt 1 Amp AC to USB Power Adapter If any item listed above is not in the package please contact APC Customer Service at 800 800 4APC for further assistance Safety Precautions Please read the following warnings carefully before using the UPB10 Use the product according to the procedures described in this manual WARNINGS e Do not attempt to disassemble any part of this product e Store and operate between 20 to 60 C 4 to 140 F and 0 to 45 C 32 to 113 F respectively as this will extend product life and prevent damage to the product e Do not allow this product to have contact wit2. conserve charge To turn the battery pack on press the Status button for second and release it The status indicators light up indicating that the battery pack is awake Checking the UPB10 Status You can check the battery charge status on the UPB10 at any time Press the Status button for 1 second and release it to display the charge status The LED status indicators will light up to display the remaining charge level The number of LEDs that light up indicate the level of charge as described in the following table Status indicators lit During Discharge 1 2 3 4 85 100 Less than 25 Fully Depleted Typical Connection Diagram All LEDs off i Typical Connection Typical Pass through Connection Note USB Charging cables sold separately are required to charge your device APC recommends the use of APC USB Charging cables to ensure compatibility Please check mobilecomputing apc com for the latest list of USB Charging Cables Specifications Output Power 8 Watts Maximum Continuous Power 10 Watts Peak Power short duration Charges from included AC power adapter PC USB port or APC Universal Power products 4 white LEDs Input Power Source Capacity Indication Size 100 mm x 65 mm x 13 7 mm 105g Storage 20 to 60 C 4 to 140 F Operation 0 to 45 C 32 to 113 F CE FCC C Tick VCCI Note This device complies with Part 15 of the FCC rules Operation is subject to the following two con
3. source and turn on the LCD backlight I don t get as many hours of runtime as I expected with the UPB1O Contact Information American Power Conversion 132 Fairgrounds Road West Kingston RI 02892 Toll Free 800 800 4APC Phone 1 401 789 5735 Fax 1 401 789 3710 Internet http www apc com USA Limited Warranty APC warrants its products to be free from defects in materials and workmanship under normal use and service for one 1 year from the date of purchase for the original purchaser Its obligation under this warranty is limited to repairing or replacing as its sole option any such defective products To obtain service under warranty you must obtain a Returned Material Authorization RMA number from APC or an APC Service Center with transportation charges prepaid and must be accompanied by a brief description of the problem and proof of date and place of purchase This watranty applies only to the original purchaser Copyright 2006 American Power Conversion All rights reserved APC 1s a registered trademark of American Power Conversion All other copyrights are the property of their respective owners Specifications are subject to change without notice Part 990 2922 001
4. B1O0 only Recycling Storage and Battery Life The UPB10 battery pack should be disposed of properly Please do not dispose in trash receptacles or incinerate For information about APC s battery recycling program visit mobilecomputing apc com For best results do not store the UPB10 where there is excessive heat or cold as such environments can damage the battery pack and reduce battery life If storing the UPB10 for an extended period completely discharge and recharge the unit before the next use This can be done by attaching the UPB10 to a USB powered device and waiting until the battery is fully discharged The UPB1O0 is fully discharged when all four status indicators are off during use Using any of the charging techniques continue charging the UPB10 completely until all status indicators are extinguished For best results the UPB10 should be fully discharged and recharged once every 3 months This will condition the cells inside the battery back to ensure the UPB10 delivers the most capacity available UPB10 does not charge the device The UPB10 may have entered the Auto Sleep Mode The power consump tion of the device may be greater than 8W The UPB10 may have entered the Auto Sleep mode The manufacturer s USB cable may not support charging func tionality My device does not charge when I connect the manufacturer s USB cable to the UPB1O0 Some devices may see the UPB10 as a utility power
5. ditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including inter ference which may cause undesired operation Weight Environmental Recharges to 100 in 3 5 hours Agency Approvals Troubleshooting Possible Cause Press UPB10 status UPB10 is fully drained button but the indica tors does not light up Corrective Action Charge the UPB10 using one of the three methods that are described under Charging the UPB10 Press the Status button for 1 second then release The sta tus indicators will illuminate and the battery will resume power output If no indica tors are lit recharge the UPBI1O Check the power specifica tion of the device before charging with the UPB10 Press the Status button for 1 second then release The sta tus indicators will illuminate and the battery will resume power output If no indica tors are lit recharge the UPB1O APC recommends the use of APC USB Charging Cables to ensure compatibility Please check mobilecomput ing apc com for the latest list of USB Charging Cables Check the LCD setting for your device Change the LCD backlight setting to off or reduce the length of time it will illuminate to extend your runtime Device can t be Device requires higher 1 Disconnect AC adapter charged by using pass input voltage or power 2 Charge the device using the through function UP
6. h water or other liquids If water or other liquids enter the battery interior immediately unplug the product from any attached power source or device Continued use of the product may result in fire or an electrical shock e Do not handle this product if hands are wet as this may cause an electrical shock e Do not place this product near a heat source or expose the battery to direct flame or heat as the battery may explode Note Failure to comply with any warning contained in this manual may result in personal injury death and or equipment damage Prior to Use Before using the UPB10 the Mobile Power Pack should be fully charged Please see the following instructions on how to use and maintain the UPB10 Product Components Status button Status indicators Serial A USB Powering Port Mini B USB Charging Port Charging the UPB10 You can charge the UPB10 using any of the following methods e Using the AC Power Adapter Attach the appropriate outlet plug to the adapter before connecting it to a power outlet for charging the UPB10 battery pack Connect the USB cable provided to the AC power adapter and plug the adapter into a wall outlet Connect the mini B connector to the UPB10 battery pack e Using your notebook or PC Charge the UPB10 battery pack through your notebook or desktop PC by connecting it with the USB power cable to a USB port and the Mobile Power Pack e Using the APC Universal Power Adapter Connect t
7. he UPB10 battery pack to an APC power adapter via the USB power port Refer to the documentation provided with the adapter for more information Checking the Charging Status The charging status of the UPB10 battery pack is indicated by the LED status indicators If the indicators are flashing this indicates that the battery pack is being charged The LED status indicators will light up sequentially as each level of charge is reached see table below Continue charging until the four white indicators are lit together and then turned off which indicates that the battery pack is fully charged LED Status Indicators During Charging Light E Less than 25 P 85 100 1 2 3 4 then Fully charged turned off When using the battery pack for the first time charge the UPB10 battery pack fully before use When the status indicators show the UPB10 is fully charged the battery pack is ready to be used Powering Devices Use an appropriate USB charging cable to power CED a Powerit _ 2 0 Connect the USB cable j to the USB output port devices such as iPods MP3 players mobile on the battery pack and the other end of the cable to the device that needs to be powered Charge it phones PDAs and portable gaming systems Turning On the UPB10 If the UPB10 battery pack has not been used charging or discharging for a period of more than 15 minutes it automatically enters sleep mode to
Download Pdf Manuals
Related Search