MSI MS-1012 White
Contents
1. MOBILE TECHNOLOGY COMPATIBLE Overview MS 1012 is shipped out as a bare bone Some of the components are equipped while some are not This installation guide provides you with the information of notebook hardware setup Before assembling your notebook please prepare installation tools and appropriate items If you are not sure about the items please contact your dealer for more information Package check list Optional Hardware Devices HDD Mini PCI WLAN card CPU Memory Before installing the notebook e he peripheral devices contained herein depend on your actual system configuration e Third party trademarks and names are the properties of their respective owners e The information contained herein relevant to software and hardware are for reference only and in accordance with actual system configuration All information are subject to change without notice Warning m Ensure power is turned off and notebook battery is removed before you install any hardware devices Use a grounded wrist strap before handling computer components such as CPU Memory HDD mini PCI Card etc Place components CPU Memory HDD mini PCI Card etc on a grounded antistatic pad or on a bed that comes with the components whenever the components are separated from the notebook If you have any difficulties in installing hardware devices please contact your dealer for further information Open View 1 Cover latch Dis2. 2 1 a b c d Unlock the CPU heat sink diagonally or according to 1 2 3 4 shown on the CPU heat sink II Improper unlocking or locking of the CPU heat sink nuts will damage the CPU 2 2 Unplug the CPU fan Bi 2 3 Use a flathead screwdriver to disengage Open the socket actuator as shown in figure 2 3a below The socket actuator should open after only a half turn and then you should be able to remove the processor with your fingers Hint Make sure your system can accommodate the Intel Pentium M Celeron M Processor that you want to install Check for motherboard BIOS and thermal compatibility by using the given documentation or by contacting the vendor if necessary This processor should only be installed in systems supporting the Intel Pentium M ase _ 2 4 Place new processor into the socket Align processor s pin A1 shown in figure 2 4 with the arrow on the micro FCPGA socket Pin A1 of the processor is identified with an embroidered corner and pin A1 of the socket is identified with a small arrow If the processor does not drop completely into the socket turn the actuator until the processor drops in completely You do not have to press down the processor If the processor does not drop completely into the socket turn the actuator until the processor drops in completely dl AAA AN FA En nn Hu ee a 7 2 5 While gently holding the pro
3. is only 1 correct connection of connecting keyboard cable 7 7 a b c Connect the cable underneath the hinge cover There is only 1 correct connection of connecting the cable Be careful not to damage the antenna PCA that is connected to the left and right display assembly hinges Damaging either antenna PCA can degrade notebook performance Y 1 A EEE Breit al EEE ELL EEE AN i in TA Ai 4 1 AE i E A in i j al lt 4 7 ic 1 j 4 a E 1 h E 1 7 8 Hold the hinge cover and snap it in place Push downward at each end of the cover to secure it 7 9 Fasten all 9 Phillips head screws II Failure to apply any screws will damage the notebook DAN a y 7 a Step 8 Entering BIOS Before powering on the notebook plug in notebook power adapter into the notebook After pressing the power button press lt Del gt immediately which will take you to the BIOS CMOS Setup Screen 8 1 CT Aoust proper a lt proper TIME by Heilas lt Enter gt Use lt gt or lt gt to configure system time 8 2 Under BOOT menu in the BIOS Setup Utility press lt Enter gt to select the first boot device 8 3 Insert a bootable OS CD into the OSD tray A AS w 4 To save exit the BIOS Setup Screen press
4. Y to save exit 8 5 After seeing the Logo immediately press Enter in order to install OS and follow the given setup messages 8 6 After installing OS insert the given driver CD to install the appropriate drivers accordingly Hint If you have any questions related to the BIOS Setup procedure or if there are any other issues please contact your local retailers or national distributors for further support
5. al storage device 6 3 a b Make sure these screws are installed in the correct locations when reinstalling the optical storage device liFailure to apply these 2 screws may cause the optical storage device to fall off Step 7 Wrapping Up 7 1 a b c Install the plastic tab and fasten 2 Phillips screws on the plastic tab 7 2 a b Install the metal shielding near the memory area and secure it with 1 Phillips screw Move the cables out of the way if necessary 7 3 a b Align the plastic cover that is below the keyboard area and snap the plastic cover in place Move the cables out of the way if necessary 7 4 a b c Actuator on the connector should be in disengaged OPEN position as shown in Figure 7 4c 7 LEST SIT III ee Teer Tr 7 5 a b c d Lay the keyboard face down on top of the case Connect the keyboard cable and engage the cable and connector in place by pressing down the actuator IIIDo not excessively bend or fold the keyboard cable Excessive flexing can damage the keyboard connector F DIME Correct Keyboard Cable connection Incorrect Keyboard Cable connection 7 6 Then put the keyboard in its normal position Slide the metal tabs on the bottom of the keyboard into their slots in the top case and lower the keyboard into place IIIDo not excessively bend or fold the keyboard cable Excessive flexing can damage the keyboard connector There
6. b Tilt up the rear of the hard drive case and pull it gently by its edges only because static electricity can permanently damage the computer parts Please use the given HDD shielding tray refer to Figure 5 la 5 2 a b c d Unscrew all 4 Phillips screws that are on the side of the HDD 5 3 a b c d Remove the HDD connector if replacing the older hard drive by pulling it away from the hard drive Insert the HDD connector to HDD Make sure to align the connector and the hard drive pin Improper alignment will cause damage to the hard drive and notebook ll T here is only 1 correct alignment and orientation in installing hard drive and hard drive connector Ae ML k Al E 3 7 60 0008 Le la 5 4 a b c d Slide the hard drive with the connector into the given hard drive shielding bay and fasten the hard drive you want to install with the 4 attached Phillips screws on the side Failure to apply 4 screws may cause hard drive assembly to fall off in the notebook hard drive area and will damage the hard drive and notebook 5 5 a b Carefully place the entire hard drive assembly into the notebook hard drive area Step 6 Installing Notebook Optical Storage Device OSD 6 1 a b Remove the two screws in order to secure the optical storage device on the bottom case 6 2 a b Pull out the optical storage device from the notebook then insert the new optic
7. cessor down with your finger secure the processor in the socket by closing the socket actuator with a screwdriver See Figure 2 5 IS 2 6 Your system is set with dip switches in order for the new processor to function correctly The dip switches can be found next to the CPU Consult processor documentation to determine the correct dip EN setting shown in figure 2 a Dothan Es and 2 6c Dothan 400 amp Celeron M go 3 ay IF LABEL REMOVED Tory IIIT LIMIN E AD JA 6 8 TO BARRER Hit OV UNINC PAT LEI J EF LULL Bu IT aah habi TEA Dothan 533 Dothan 400 amp Celeron M 2 7 Plug the CPU fan 2 8 a b c d e Lock the CPU heat sink diagonally or according to 1 2 3 4 shown on the CPU heat sink Improper unlocking or locking of the CPU heat sink nuts will damage the CPU Hint We recommend you to apply the given thermal grease for better heat conduction between your CPU and the heat sink Hint Please check the heat sink and make sure it is in good contact with the CPU before you turn on your notebook Step 3 Installing Notebook Memory 3 1 Remove the older module if replacing by pulling tabs of the socket outward using your thumbs 3 2 The module should pop up into a 45 degree angle Remove the module by pulling it gently backward Use side to side moti
8. e y of the way 1 7 Carefully remove the keyboard cover by lifting the keyboard at the switchboard PCA end Pull the keyboard toward the display assembly in order to release the keyboard from the top case a T P 2 1 8 Turn the keyboard over Do not excessively bend or fold the keyboard cable Excessive flexing can damage the keyboard cable connectors fal 1 9 a b c Disconnect the keyboard cable by disengaging the cable actuator on the motherboard Do not excessively bend or fold the keyboard cable Excessive flexing can damage the keyboard cable connectors II Do not pull the cable without the cable actuator MI og 4 1 uf 1 10 a b c d Disengage the plastic cover gently at both sides and pull the plastic cover away from the notebook Hint Gently pry the plastic cover if needed Be careful not to damage the plastics or cables underneath 1 11 a b c Lift the plastic cover up slowly and be careful not to damage the plastics and cables underneath Hint You do not have to unplug the connector underneath the cover 1 12 a b c Remove in 2 Philips screws on the plastic tab from the case and lift the plastic tab upward e gt 1 13 a b Unscrew only the Phillips head screw on the metal shielding and remove the metal shielding i 3 Mmmm E Step 2 Installing the CPU
9. on if necessary to remove Push down the memory module gently until the metal locking levers aside from the DIMM socket 1 is fastened 111 The location of the notch along the gold edge of the memory module needs to be lined up with keyed notch in the socket Memory module can only fit in one direction due to the keyed notch Wrong orientation will cause improper installation and may damage the memory modules or DIMM sockets 111 era i paraa ri FT iF eed e E 3 3 a b c If you have more than one memory module please align the 2nd memory module to the DIMM socket 2 Memory should be inserted firmly at a 45 degree angle and pushed down until module snaps into place Step 4 Installing Mini PCI WLAN Card 4 1 Remove the older module if replacing by pulling tabs of the socket outward using your thumbs an e IA a aki em CERNS ee e OO SRR OMe Sea Ch H 3 l Ea a Ceras 4 2 a b c The module should pop up into a 45 degree angle Remove the module by pulling it gently backward Use side to side motion if necessary to remove Unplug the antennas Mini PCI module should be inserted firmly at a 45 degree angle and pushed down until module snaps into place After the module snaps into place connect antennas on the Mini PCI card E i 1511 1 1 Step 5 Installing Notebook Hard Drive HDD 5 1 a
10. play Panel Quick Launch Buttons and Power button Status LEDs Keyboard Touchpad Stereo Speakers Bottom View 1 Battery Unlock Button 2 Battery Pack 111111111111 i E a 11 a Tuer 1 wi a 5 i Right view Left view Front view Open view Others Step 1 Removing the Cover 1 1 a b c d e f g h i Close the display From the rear of the laptop remove all 9 Philips screws 1 2 a b Remove both PCMCIA card and SD card 1 3 Open vour laptop to a 30 to 45 degree anale shown in the Figure below 1 4 a b c d e Prepare a proper size flat head screwdriver and locate the 3 notches Carefully insert the flathead screwdriver into the notches and gently lift up the hinge cover Gently pry the hinge covers if needed and be careful not to damage the plastics wireless and cables underneath 1 5 a b c If necessary while holding the hinge cover carefully insert the flathead screwdriver under both side below the display assembly hinge gently pry up and then lift the hinge cover out This procedure may need to be repeated Hint u ory the hinge cover if needed Be careful not to damage the plastics and cables underneath 1 6 a b c Unplug the connector underneath the hinge cover so that it is out 2 w gt K gt f I a
Download Pdf Manuals
Related Search