Home
AKG DAB/RDS Tuner 970
Contents
1. L 2 indicates medium compression and l shows maximum compression No compression is recommended especially for classical music Note that other radio stations may be far louder and make therefore sure that amplifier levels are not set too high when changing from one station to another Manual Tune In this section you can activate Manual Tuning in case the Autotune function is unable to find any stations You can also use Manual Tuning to assist in positioning the antenna for best recep tion of a specific station FM AM Tuner Operation The TU 970 s tuner is capable of tuning AM FM and FM Stereo broadcast stations Stations may be tuned manually or automatically or they may be stored as favorite station presets and recalled from a 30 position memory 10 OPERATION Station Selection 1 Press the Band Selector Ki on the front panel or on the remote control to select either the FM or AM band 2 Press these buttons again at any time to switch between AM FM and DAB 3 Press the Select button EE to select the Auto Tune mode from the following options Manual Tune Auto Tune or Preset Tune 4 To automatically search for the next higher or lower frequency station that has an acceptable signal turn the Control Ring on the front panel E or press the Scroll buttons on the remote pressed and release it as soon as the tuner starts the frequency search To tune to the next station turn the ring again To manually se
2. first unplug the unit from the AC wall outlet and wait at least three minutes After the pause reconnect the AC power cord and check the unit s operation If the system still malfunctions a system reset may clear the problem To reset the TU 970 press and hold the Func tion FM Mode Button EA for 5 seconds until the Information Display shows FACTORY RESET Note that when the system is reset all tuner presets will be lost and must be reentered If the system is still operating incorrectly there may have been an electronic discharge or severe AC line interference that has corrupted the memory or microprocessor If these steps do not solve the problem consult your dealer or an authorized Harman Kardon service center OPERATION 11 Troubleshooting Guide This unit is designed for trouble free operation Most problems users encounter are due to operating errors If you have a problem first check this list for a possible solution If the problem persists consult your authorized Harman Kardon Service Center If the problem is No lights appear when System Power button is pressed No sound is heard Sound distorts particularly in stereo mode Intermittent or continuous buzzing or hissing Display says No stations Available Display has gone blank or says service off air 12 TROUBLESHOOTING GUIDE Make sure that the Unit is plugged into a live outlet Make sure the outlet is active Tune to an active stat
3. RC Standby Power On Scroll Button Numeric Keys Function FM Mode Selector Clear Button Band Selector Info RDS Button Auto Tuning Button 6 REMOTE CONTROL FUNCTIONS Select Button Memory Button Standby Power On Press this button to turn on the TU 970 press it again to turn the unit off to Standby Note that the Power Indi cator EE next to the switch will turn blue when the unit is on Numeric Keys These buttons serve as a ten button numeric keypad to enter tuner preset positions or to tune stations directly Clear Button Press this button to clear presets trom your station list Info RDS Button Pressing this button will change the content of the lower display line of the Information Display Auto Tune Button In DAB mode press this button to automatically scan all available local stations To scan for all available stations keep the button pressed for three seconds until AUTOSCAN FULL is shown in the Infor mation Display Ed Scroll Buttons Press W to tune lower frequency stations and to tune higher fre quency stations When a station with a strong signal is tuned the Information Display will read TUNE D Press again briefly to tune to the next frequency increment in Manual Tune Mode or keep pressed for automatic search for the next station with a signal strong enough for acceptable reception in Auto Tune Mode These buttons also control the parameters in the
4. a station list you can also store presents into the tuners memo ry 1 Tune to the desired station with the Control Ring E 2 Press the Memory Button on the front panel EJ or on the remote control D You will see the 01 segments in the Information Display Ed will start to blink 3 Turn the Control Ring until the desired station preset is shown in the Information Display The desired preset can also be entered with the Numeric Keys on the remote control 4 Within 4 seconds press the Memory Button again to store the station in the memory Information settings The DAB signal contains besides the radio sta tion additional information This information can be made visible in the lower display line of the Information Display Ed The following information is available to display 1 Dynamic Label Segment DLS scrolling text supplied by the broadcaster 2 Program Type describes the type of broad cast e g Pop Music or Drama 3 Multiplex Name will show the name of the multiplex of the broadcaster 4 Time and Date 5 Bitrate shows the bitrate of the incoming digital signal 6 Channel and Frequency To change between the options press the Info Button on the front panel Fi or on the remote control B Note that the upper display line will always show the actual station Pressing the Info Button again will show the next option When you have found the information you would like to display pres
5. different menus like the Control Ring Ed on the front panel Function FM Mode Selector In DAB mode pressing this button will activate station order signal error rate preset tune software ver sion Dynamic Rate Control or manual tune fea tures In FM mode press this button to select the stereo or mono mode for FM tuning In the stereo mode the word STERE 0 will be shown in the Information Display F and stereo reception will be provided when stations are transmitting stereo signals In the mono mode the left and right signals trom stereo broadcasts will be mixed together and reproduced through all channels Select MON O for better reception of weak signals Band Selector Press this button to change between the DAB FM and AM frequency bands O Select In FM or AM mode press this but ton to select Auto Tune Manual Tune or Preset Tune D Memory Button Press this button to open the memory position that stores a preset location in the tuner 10 DAB presets can be stored as well as 30 FM and 30 AM presets See page 9 for more information on tuner pre sets Installation and Connections Audio Connections After unpacking the unit and placing it on a solid surface capable of supporting its weight you will need to make the connections to your pre amplifier or integrated amplifier These steps need to be done only when the tuner is first installed Audio Equipment Connections We recommend that you use hig
6. station KP Remote Sensor Window The sensor behind this window receives infrared signals from the remote control Aim the remote at this area and do not block or cover it unless an external remote sensor is installed Rear Panel Connections OPTICAL O O DIGITAL OUTPUT DAB COAXIAL MODEL NO TU970 harman kardon NORTHRIDGE CALIFORNIA USA CAUTION uy RISK OF ELECTRIC SHOCK INP DO NOT OPEN A DO NOT EXPOSE TO RAIN OR MOISTURE 230V 50Hz SW ce El Optical and Coaxial Digital Outputs Q FM Antenna AM Antenna Analog Audio Outputs Optical and Coaxial Digital Outputs Connect one of these jacks to the optical or coaxial digital input of your pre amplifier or inte grated amplifier if available Note that these digital outputs only contain the digital signal from the DAB stations For FM AM reception you will have to connect the analog outputs at all times FM Antenna Connect an indoor or external FM antenna to this terminal AM Antenna Connect the AM loop anten na supplied with the receiver to these terminals If an external AM antenna is used make connec tions to the AM and GND terminals in accor dance with the instructions supplied with the antenna DAB Antenna AC Power Cord Remote Control Output Remote Control Input Analog Audio Outputs Connect these jacks to the tuner input of your pre amplifier or integrated amplifier for analog aud
7. the TU 970 preset memories first select the FM band Next press and hold the Memory Button EI until the station frequency indication begins to increase Release the button and note that the tuner will search the entire FM band and stop briefly at each station that has acceptable signal strength The TU 970 will automatically assign a preset number to each station and then search for the next station NOTE Using the automatic tuning mode in areas with more than 30 FM stations will com pletely fill the preset memories and overwrite any previously memorized presets for either AM or FM stations TIP The automatic scan process may enter stations that you do not wish to retain in the memory These unwanted stations may be removed from the memory by pressing the Memory Button JD once the preset to be deleted is shown on the display Within 5 seconds press the Clear Button on the remote control P to confirm the deletion Recalling Preset Stations To manually select a station previously entered in the preset memory press the Numeric Keys gt that correspond to the desired station s memory location To manually tune through the list of stored preset stations one by one press the Select Button i until the Information Display shows Preset Tune Turn the Control Ring Ed or press the Scroll Buttons on the remote control to scroll through the list of presets Operation RDS Operation RDS Radio Data System transmits stati
8. the con nection The supplied antenna is for indoor use only 5 Connect a DAB Antenna to the DAB Anten na connection The supplied antenna is for internal use only Fix it to the wall in a vertical direction The strength of the incoming signal can be shown on the Information Display by pressing the Select button IEO The more segments are visible in the lower display line the stronger the signal By changing the position of the antenna you can increase the signal strength You can also opt for an external anten na available at your dealer When all connections are complete plug the power cord into a non switched 230 Volt AC wall outlet You re ready to enjoy the TU 970 INSTALLATION AND CONNECTIONS 7 Operation Basic Operation The TU 970 is simple to operate and very similar to tuners you may have used in the past This section will explain the use of several features that may be new to you e Install the two supplied AAA batteries in the remote as shown Be certain to observe the and polarity indicators shown in the bottom of the battery compartment e When using the TU 970 for the first time it will be placed in a standby mode as indicated by the amber color of the Power Indicator EX Once the unit is in standby you may begin a lis tening session by pressing the System Power Control FJ on the front panel or the Power On button on the remote control Note that the Power Indicator EE will tur
9. the stations program type indication of national regional or local programs and the correct time RDS also allows you to search for favorite program types A DOT matrix display brings all this information to you with high visibility As more FM stations become equipped with RDS capabilities the TU 970 will serve as an easy to use center for both information and entertainment _CAUTION _ RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important Operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE INTRODUCTION 3 Front Panel Controls BC kadio 5 Live GL 15 07 2003 TU 970 PAB 0 Band harman kardon EE Power Indicator FA System Power Control EJ Band selector EJ Function FM Mode Selector EE Power Indicator This LED will illuminate in am
10. THER MUSIC Other Music e WEATHER amp METR Weather e FINANCE Finance e CHILDREN S PROGSX Children s Programmes e SOCIAL AFFAIRS Social Affairs e RELIGION Religion e PHONE IN Phone In e TRAVEL amp TOURING Travel e LEISURE amp HOBBY Leisure e JAZZ MUSIC Jazz Music e COUNTRY MUSIC Country Music e NATIONAL MUSIC National Music e OLDIES MUSIC Oldies Music e FOLK MUSIC Folk Music e DOCUMENTARY Documentary e ALARM TEST Alarm Test e ALARM ALARM Alarm You may search for a specific Program Type PTY by following these steps 1 Press and hold the RDS Button AO until the Information Display will show RDS PROGRAM TYPE 2 Turn the Control Ring on the front panel to scroll through the list of program types Once you have found the program type you would like to listen to press the Select Button EE 3 Turn to Control Ring again to start the PTY Search When a station is tuned the search will stop and the display will show the stations Call Let ters or other Program Service information To turn off the PTY Search at any time press the RDS Button again NOTE Many stations do not transmit a specific PTY The display will stay blank when such a sta tion is selected and PTY is active Processor Reset In the rare case where the unit s operation or the displays seem abnormal the cause may involve the erratic operation of the system s memory or microprocessor To correct this problem
11. TU 970 OWNER S MANUAL Info RDS Auto Tune Dimmer Memory es ees eee eee sz harman kardon OSS D harman kardon Power for the Digital Revolution Table of Contents Introduction Front Panel Controls Rear Panel Connections Remote Control Functions Installation and Connections Declaration of Conformity CE We Harman Consumer International 2 Route de Tours 72500 Chateau du Loir FRANCE Operation Basic Operation Station List Preset Setting Function Control Station Order Signal Error Rate Oo O O DO O9 O9 NOURA W Preset Tune 11 RDS Operation 12 Troubleshooting Guide 13 Technical Specifications declare in own responsibility that the product described in this owner s manual is in compliance with technical stan dards EN 55013 6 1990 EN 55020 12 1994 EN 60065 1993 EN 61000 3 2 4 1995 MEA Carsten Olesen Harman Kardon Europe A S 10 03 Typographical Conventions In order to help you use this manual with the remote control front panel controls and rear panel connections certain conventions have been used EXAMPLE bold type indicates a specific remote control or front panel button or rear panel connection jack EXAMPLE OCR type indicates a message that is visible on the front panel information display EE number in a square indicates a specific front panel control number in a circle indicates a rear panel connection number in a
12. arch select the Manual Tune mode by pressing the Select button EE until the Information Display shows Manual Tune Turn the Control Ring to increment the fre quency step by step When the Information Display shows TUNED the station is properly tuned and should be heard with clarity NOTE When the FM reception of a stereo sta tion is weak the audio quality will be increased by switching to Mono mode by pressing the FM Mode Selector EJ on the front panel so that the STERE O indication changes to MONO Preset Tuning Up to 30 FM and 30 AM stations may be stored in the TU 970 s memory for easy recall using the remote control In order to program preset stations into the memory you must use the front panel controls To enter a station into the memory first tune the station using the steps outlined above Then 1 Press the Memory Button J on the front panel or on the remote control Note that CHO1 starts blinking in the lower display line of the Information Display 2 Within four seconds turn the Control Ring E until the Information Display shows the corresponding location where you wish to store this station s frequency 3 Press the Memory Button again to confirm 4 Repeat the process after tuning any additional stations to be preset Auto Preset Preset stations may also be programmed auto matically for the entire FM band To automatical ly enter each station that may be tuned with acceptable quality into
13. ations To scan for all available stations keep the button pressed for three seconds until AUTOSCAN FULL is shown in the Infor mation Display Ed Information Display This dual line display delivers messages and status indications to help you operate the tuner EJ Dimmer Press this button to dim the front panel display The first press of the button will dim the displays to one half normal brightness the next press will turn back to normal bright ness The display will return to normal brightness the next time the unit is turned on EJ Memory Button Press this button to open the memory position that stores a preset loca tion in the tuner 10 DAB presets can be stored as well as 30 FM and 30 AM presets See page 9 for more information on tuner presets KJ Memory K Control Ring EE Select KP Remote Control Sensor He Control Ring Turn counterclockwise to tune lower frequency stations and clockwise to tune higher frequency stations When a station with a strong signal is tuned the Information Display pA will read TUNE D Turn again to tune to the next frequency increment in Manual Tune Mode or automatically to the next sta tion with a signal strong enough for acceptable reception in Auto Tune Mode The ring also controls the parameters in the different menus fil Select In FM or AM mode press this but ton to select Auto Tune Manual Tune or Preset Tune In DAB mode press this button to select the displayed
14. ber when the unit is in the Standby mode to signal that the unit is ready to be turned on When the unit is in operation the indicator will turn blue F1 System Power Control Press this button to turn on the TU 970 press it again to turn the unit off to Standby Note that the Power Indi cator EE next to the switch will turn blue when the unit is on Kk Band Selector Press this button to change between the DAB FM and AM frequency bands E Function FM Mode Selector In DAB mode pressing this button will activate station order signal error rate preset tune software ver sion Dynamic Rate Control or manual tune fea tures In FM mode press this button to select the stereo or mono mode for FM tuning In the stereo mode the word STERE 0 will be shown in the Information Display F and stereo reception will be provided when stations are transmitting stereo signals In the mono mode the left and right signals trom stereo broadcasts will be mixed together and reproduced through all channels Select M ON for better reception of weak signals 4 FRONT PANEL CONTROLS E Info RDS Button J Auto Tune Button Information Display EJ Dimmer Eq Info RDS Button In DAB mode pressing this button will change the content of the lower display line of the Information Display In RDS mode it will change between the different RDS options J Auto Tune Button In DAB mode press this button to automatically scan all available local st
15. elect MANUAL TUNE by pressing the Select Button or turn the Control Ring El to select AUTOTUNE FULL or AUTOTUNE LOCAL to try to manually find available stations If no stations can be found please check that the antenna is connected correctly and if your area is covered by DAB Station List Once the TU 970 has finished the scanning sequence it will display the available stations in alphanumeric order Turn the Control Ring El clockwise or counterclockwise to scroll through the list of available stations The upper display line in the Information Display FA will always show the current station you are listening to The lower display line shows the next station in the list To select the next station simply press the Select Button on the front panel KE or on the remote control The current station list will remain in the memo ry of the TU 970 It can be updated by running the Autotune function as described above or deleted by resetting the TU 970 s memory see page 11 NOTE The station list can be shown in different order For more info see page 9 It can occur that one of the stations in your list is temporarily not available A symbol will be visible in front of the station name to indicate such a Station If you select the station the Information Display FA will show STATIONNOT AVAILABLE and will go back to the current radio station Operation Preset Setting Besides having the TU 970 create
16. h quality inter connect cables when making connections to source equipment and recorders to preserve the quality of the signals When making connections to audio source equipment it is always a good practice to unplug the unit from the AC wall outlet This prevents any possibility of accidentally sending audio or transient signals to the speakers that may dam age them 1 Connect the analog output of the TU 970 to the tuner input of your pre amplifier or integrat ed amplifier 2 For DAB signals connect the optical or coaxial digital output of the TU 970 to an optical digital audio input of your pre amplifier or integrated amplifier if available 3 Assemble the AM Loop Antenna supplied with the unit as shown below Connect it to the AM terminals For best reception place the antenna away from the unit as well as from sources of RF emissions such as a television or computer It should also be placed away from contact with any metal object In areas where signals are weak an out door antenna may improve sound and reception quality Connect the antenna making certain to also connect a ground wire to the GND termi nals 4 Connect a FM Antenna to the FM Antenna connection The FM antenna may be an external roof antenna an inside powered or wire lead antenna or a connection trom a cable sys tem Note that if the antenna or connection uses 300 ohm twin lead cable you need to use a 300 ohm to 75 ohm adapter to make
17. he best reception will be shown on top of the list Stations with weak or no reception will be moved to the bottom of the list The Tidy Station option will do the same as the Active Station option but will remove the sta tions in your area with no reception Signal Error Rate In this section you can see the level of correction the TU 970 is applying to the DAB signal to maintain the audio quality The level will be indi cated by a numeric value between 0 no correc tion and 99 maximum correction For an acceptable quality the value of 50 should not be exceeded OPERATION 9 Operation Preset Tune In this section you can tune presets of stations that broadcast only periodically stations which were not found during the Autotune process If you return to this preset in the future and at that time is does not broadcast the display will show STATIONNOT AVAILABLE Software Version This section allows a visual check of software version installed in your TU 970 This might be helpful in case servicing of your tuner may be necessary Dynamic Range Control DRC Value In this section you can set the level of compres sion of stations to eliminate the differences in dynamic range or sound level between radio sta tions Popular music would normally be more compressed than classical music resulting in possible different audio levels when changing from one station to the other Setting the DRC to O means no compression
18. io playback Be certain to observe proper channel connec tions using the color coded cables and connec tors so that red connects right channels and white connects left channels NOTE Before making any audio connections unplug all components of your audio system from their AC power outlets To reduce the possi bility of hum or noise in your system place all audio interconnection cables away from both AC power cords and speaker wires DAB Antenna Connect a DAB antenna to this terminal AC Power Cord Connect this plug to an AC outlet If the outlet is controlled by a switch make certain that it is in the ON position Remote Control Output Connect this jack to the infrared IR input jack of another compatible Harman Kardon remote controlled product to have the built in Remote Sensor on the tuner provide IR signals to other compatible products Remote Control Input Connect the output of a remote infrared sensor or the remote control output of another compatible Harman Kardon product to this jack This will enable the remote control to operate even when the front panel Remote Sensor on the tuner is blocked This jack may also be used with compatible IR remote control based automation systems REAR PANEL CONNECTIONS 5 Remote Control Functions CLEAR MEMORY ED 10 AUTO TUNING INFO RDS SELECT g E QT A Y ROL A hec FM MODE BAND E 8 C harman kardon TU 970
19. ion Check for correct amplifier settings Check the connections and wires Use a more directional antenna Place the unit farther away from these appliances Install noise filters on the appliances Check that antenna is connected Ensure that DAB coverage exists in your area This may occur if a broadcaster changes the label of a service or removes a label whilst you are listening to it Try to retune to this station using the Autotune procedure Technical Specifications FM Section Frequency Range Signal to Noise Ratio Presets Section Frequency Range Signal to Noise Ratio Presets DAB Section RF Section Display Presets Audio Output Optical S PDIF General Power Requirement Power Consumption Dimension Max Width Height Depth Weight Depth measurement includes knobs buttons and terminal connections Height measurement includes feet and chassis 87 50 MHz to 108 00 MHz 50 kHz steps 65dB Mono 60dB Stereo 30 522 kHz to 1620 kHz 9 kHz steps 35dB 30 Band Ill 174MHz 240MHz Input 50 Ohm nominal Max signal 3dBm typ Sensitivity 96dBm typ Adjacent Channel Rejection 35dB typ 2 line by 16 character DOT Matrix 10 Stereo 2 5V P P A8kHz sample rate 16 bit sample resolution IEC60958 Compliant A8kHz sample rate 24 bit sample resolution 230 240V AC 50Hz QW 3W standby 442mm 63mm 299mm 3 4kg All features and specifications are subject to change without notice Har
20. man Kardon and Power for the Digital Revolution are registered trademarks of Harman Kardon Incorporated TECHNICAL SPECIFICATIONS 13 harman kardon H A Harman International Company 250 Crossways Park Drive Woodbury New York 11797 www harmankardon com Harman Consumer International 2 Route de Tours 72500 Chateau du Loir France 2003 Harman Kardon Incorporated Part CQX1A887Z
21. n blue To turn the unit off at the end of a listening session simply press the System Power Control FA on the front panel or the Standby button on the remote This places the unit in the Stand by mode and the Power Indicator EE will turn amber to remind you that the unit is ready for operation when a power command is received from the remote When you will be away from home for an extended period of time it is always a good idea to completely turn the unit off by unplugging it from the AC wall outlet Note that the backup system in the TU 970 will retain information such as programmed presets for 14 days e To dim the brightness of the front panel dis play press the Dimmer button EJ on the front panel The first press will dim the lights to halt normal A second press will turn the display to normal brightness again 8 OPERATION DAB Operation When you turn on the tuner the tuner will ini tialize During 2 seconds the display will show the following messages After the initialization process the tuner will per form an automatic scan for available local digital radio stations This sequence can not be inter rupted During the sequence the following mes sage will be visible on the display The arrows show the progress of the sequence On the right top side you will see how many digital stations have been found If no digital stations can be found the display will show NO STATIONS AVAILABLE You can now s
22. n oval indicates a button or indicator on the remote 2 TABLE OF CONTENTS Introduction Congratulations With the purchase of the Harman Kardon TU 970 you are about to begin many years of listening enjoyment While sophisticated systems are hard at work within the TU 970 to make all of this happen hookup and operation are simple To obtain maximum enjoyment from your new tuner we urge you to take a few minutes to read through this manual This will ensure that connections are made properly In addition a few minutes spent learning the functions of the various controls will enable you to take advan tage of all the power the TU 970 is able to deliver If you have any questions about this product its installation or operation please contact your dealer He is your best local source of information Description and Features The TU 970 is equipped with DAB Digital Audio Broadcast and RDS Radio Data System bringing a wide range of information to radio listeners Until now analogue radio signals such as FM or AM have been subject to numerous kinds of interference on their way from the transmitter to your radio These problems were caused by mountains high rise buildings and weather conditions With DAB you can now receive CD like quality radio programs without any annoying interference and signal distortion Now in use in many countries RDS is a system for transmitting station identification a descrip tion of
23. nnouncement When selected TRAFFIC ANNOUNCE will blink for 3 seconds After 3 seconds the tuner will scan the FM band searching for available traffic announcements e The stations frequency Some RDS stations may not choose to include some of these addi tional features If the data required for the selected mode is not being transmitted the Information Display will show a NO PTY NO TEXT or NO TIME message after the indi vidual time out or will switch back to the previ ous display e In any FM mode the RDS function requires a strong enough signal for proper operation If you receive a partial message or see any RDS indica tor going on and off try slowly adjusting the antenna to improve the signal strength or tune to another stronger RDS station Program Search PTY A major benefit of RDS is its ability to encode broadcasts with Program Type PTY codes that indicate the type of material being broadcast The following list shows the abbreviations used to indicate each PTY along with an explanation of the PTY e NEWS News e CURRENT AFFAIRS Current Affairs e INFORMATION Information e TRAFFIC Traffic information e SPORT Sport e EDUCATION Education e DRAMA Drama e CULTURES Culture e SCIENCE Science e VARIED SPEECH Varied e POP MUSIC Pop Music e ROCK MUSIC Rock Music eEASYLISTENING Easy Listening Music e LIGHT CLASSICS M Light Classical Music e SERIOUS CLASSICAL Serious Classical Music e O
24. on call signs or network information station program type text messages about the station or specifics of a musical selection and the correct time RDS Tuning When an FM station is tuned in and it contains RDS data the TU 970 will automatically display the Program Service which is the stations call sign in the lower display line of the Informa tion Display with some private stations also offering other information changing every 2 to 5 seconds RDS Display Options When an RDS station is tuned press the RDS Button on the remote control B or on the front panel FE to cycle through the RDS displays in the following order e The Program Service or Station Name e The current time of the day CLOCK TIME as transmitted by the station It will take 3 5 seconds for the time to appear In the meantime the word RDS CLOCK TIME will flash in the display Note that the accuracy of the time message is set by the radio station not by the TU 970 e The Program Type PTY as shown in the fol lowing list in this manual e A Radio Text message containing special information from the broadcast station Note that this message will scroll across the display to permit messages longer than the positions in the display It will take 3 seconds for the text message to appear in the meantime the word RDS RADIO TEXT will flash in the display If no Radio Text is available the display will show the Program Service Station Name e Traffic A
25. s the Select Button HO to activate the change Function Control The DAB mode in the TU 970 contains a menu structure to access various system options To enter the menu press the Function Button on the front panel ET or on the remote control once To scroll through the list of sections of the menu turn the Control Ring El or press the Scroll Buttons on the remote control The sections will be shown on the lower display line in the Information Display To enter a section and see the options press the Select Button Select button k gt You can scroll through the options with the Control Ring and activate an option by pressing the Select Button once that option is shown on the Information Display Station Order In this section you can select the way the station list is displayed The options are Favorite Station Alphanumeric Active Station and Tidy Station The Favorite Station option will build the station list based on the stations that you listen to most of the time These stations will be marked on the Information Display with a Y symbol The 10 favorite stations will be moved to the start of your station list so you do not always have to scroll through the whole list to find your favorite station The Alphanumeric option is the default setting It will list the stations in numeric and alphabetical order The Active Station option will sort the station list by quality of the signal The stations with t
Download Pdf Manuals
Related Search
Related Contents
Hotpoint MWH2021B microwave LCD – FRAME - 32” HD 100Hz - 37” HD 100Hz Developer MagicTM: Debugger User's Guide 78K0/Fx2 - CAN it! - Renesas Electronics Manual - VTP UP RESOLUCIÓN No. 000026 ( 6 de enero de 2005) Por la cual ResMed Ventilation Hood vpap-st User's Manual Cuadro Normas Sanitarias PondoClear Set User Manual Analog Output Copyright © All rights reserved.