Smeg WHT914LSUK washing machine
Contents
1. Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment Laundry should be rearranged and re spun Regular drum cleaning is not applied Clean the drum regularly See 8 2 A CAUTION if you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorized Service Agent Never try to repair a nonfunctional product yourself Washing Machine User s Manual 317 EN2. Washing Machine User s Manual 25 EN 8 4 Cleaning the water intake filters There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap These filters prevent foreign substances and dirt in the water to enter the washing machine Filters should be cleaned as they do get dirty under running water 4 Replace the seals and filters carefully and tighten their In addition prior to transporting the machine e g when moving to another house and in case of freezing of the water water may have to be drained completely Close the taps nuts by hand f CAUTION Foreign substances left in the pump filter may damage your machine or may cause noise problem 2 Remove the nuts of the water intake hoses to access the filters on the water intake valves Clean them with an appropriate brush If the filters are too dirty remove them from their places with a pliers and clean in this way 3 Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly 8 5 Draining remaining water and cleaning the pump filter The filter system in your machine prevents solid items such as buttons coins and fabric fibers clogging the pump impeller during discharge of washing water Thus the water will be discharged without any problem and the service life of the pump will extend lf the mach
3. Jake out all substances in the pockets such as coins pens and paper clips and turn pockets inside out and brush Such objects may damage the product or cause noise problem Put small size clothes such as infant s socks and nylon stockings in a laundry bag or pillow case Place curtains in without compressing them Remove curtain attachment items Fasten zippers sew loose buttons and mend rips and tears Wash machine washable or hand washable labeled products only with an appropriate programme Do not wash colours and whites together New dark coloured cottons release a lot of dye Wash them separately e Jough stains must be treated properly before washing If unsure check with a dry cleaner e Only use the dyes color changers and descaling agents which are appropriate to machine wash Always follow the instructions on the package e Wash trousers and delicate laundry turned inside out e Keep laundry items made of Angora wool in the freezer for a few hours before washing This will reduce pilling e Laundry that are subjected to materials such as flour lime dust milk powder etc intensely must be shaken off before placing into the machine Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage 6 3 Things to be done for energy saving Following information will help you use the product in an ecological and energy efficient manner e Qperate the product in the highest capacit
4. Programme and consumption table EN T en S Selectable Programme So 5 temperature range D e G v o aC 5 Bl sg a 2 2 O lt on Te e a D D EISI Ol S 5 2 8 8 2 2 W SIED Ea uy 60 9 54 1 06 1600 Cold 60 Cotton Eco 60 4 5 44 0 90 1600 Cold 60 40 4 5 43 0 84 1600 Cold 60 HygieneCare 90 9 94 2 60 1600 30 90 Shirts 60 4 85 1 29 800 Je e gt 60 Cold Mixed 40 4 al 0 90 1000 40 Cold Sports 40 4 60 0 60 1000 40 Cold Curtains 40 2 2 Es s E E E a 40 Cold Dark Wash 40 4 80 0 90 1000 Cold 40 Steam Refresh 1 1 o7 Duvet 40 67 0 82 1000 Cold 60 Hand Wash 30 15 40 0 22 600 Cold 30 Delicate 40 3 54 0 44 1000 ae 8 40 Cold 14 Minutes 30 2 34 0 17 1400 Cold 30 Wool 40 2 45 0 35 1000 Cold 40 l 60 4 65 ae E Oe E E Cold 60 Synthetics 40 4 65 CLS I ACO Oo Cold 60 90 9 70 2 20 1600 jejo Cold 90 Cottons 60 9 70 1 50 1600 Jeje Cold 90 40 9 70 1 00 1600 JeeJee Cold 90 e _ Selectable Automatically selected no canceling Energy Label programme EN 60456 Ed 3 lf maximum spin speed of the machine is lower then this value you can only select up to the maximum spin speed Programme detects the type and quantity of the laundry to automatically adjust water and ener
5. etc used solely for delicate clothes e When washing dark coloured clothes and quilts it is recommended to use liquid detergent e Wash woolens with special detergent made specifically for woolens A CAUTION use only detergents manufactured specifically for washing machines CAUTION Do not use soap powder Adjusting detergent amount The amount of washing detergent to be used depends on the amount of laundry the degree of soiling and water hardness e Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam poor rinsing financial savings and finally environmental protection e Use lesser detergent for small amounts or lightly soiled clothes Using softeners Pour the softener into the softener compartment of the detergent drawer e Do not exceed the gt max lt level sign on the softener compartment e f the softener has lost its fluidity dilute it with water before putting it in the detergent drawer Using liquid detergents If the product contains a liquid detergent cup e _ Put the liquid detergent container into the compartment no 2 e ifthe liquid detergent lost its fluidity dilute it with water before putting it into the detergent container 12 7 EN Washing Machine User s Manual If the product does not contain a liquid detergent cup e Do not use liquid detergent for the prewash in a programme with
6. in the figure e Jo prevent the waste water to go back into the machine again and to ensure easy drainage do not immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm If it is too long cut it short e The end of the hose should not be bent it should not be stepped on and the hose must not be pinched between the drain and the machine e f the length of the hose is too short use it by adding an original extension hose Length of the hose may not be longer than 3 2 m To avoid water leak failures the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak 8 EN Washing Machine User s Manual 5 6 Adjusting the feet A CAUTION In order to ensure that the product operates more silently and vibration free it must stand level and balanced on its feet Balance the machine by adjusting the feet Otherwise the product may move from its place and cause crushing and vibration problems CAUTION Do not use any tools to loosen the lock nuts Otherwise they will get damaged 1 Loosen the lock nuts on the feet by hand 2 Adjust the feet until the product stands in a stable and balanced way 3 Tighten all lock nuts by hand again 5 7 Electrical connection Connect the product to a grounded outlet protected by a 13 A fuse Our company shall not be liable for any d
7. laundry Excessive laundry was loaded in Do not load the machine in excess Load with amounts recommended in the Programme and consumption table Wrong programme and temperature were selected Select the proper programme and temperature for the laundry to be washed Wrong type of detergent is used Use original detergent appropriate for the machine Too much detergent is used Put the detergent in the correct compartment Do not mix the bleaching agent and the detergent with each other Washing performance is poor Oily stains appeared on the laundry Regular drum cleaning is not applied Clean the drum regularly For this please see 8 2 Washing performance is poor Clothes smell unpleasantly Odours and bacteria layers are formed on the drum as a result of continuous washing at lower temperatures and or in short programmes Leave the detergent drawer as well as the loading door of the machine ajar after each washing Thus a humid environment favorable for bacteria cannot occur in the machine Colour of the clothes faded Excessive laundry was loaded in Do not load the machine in excess Detergent in use is damp Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures A higher temperature is selected Select the proper programme and temperature according to the type
8. prewash e Liquid detergent stains your clothes when used with Delayed Start function If you are going to use the Delayed Start function do not use liquid detergent Using gel and tablet detergent e f the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup put the gel detergent into the main wash detergent compartment during first water intake If your machine contains a liquid detergent cup fill the detergent into this cup before starting the programme e f the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet put it directly into the drum before washing e Put tablet detergents into the main wash compartment compartment nr 2 or directly into the drum before washing Using starch e Put the liquid soda powder soda or the fabric dye into the softener compartment Do not use softener and starch together in a washing cycle Wipe the inside of the machine with a damp and clean cloth after using starch Using limescale remover e When required use limescale removers manufactured specifically for washing machines only Using bleaches Add the bleach at the beginning of the washing cycle by selecting a prewash program Do not put detergent in the prewash compartment As an alternative application select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing Step e Do not u
9. required the auxiliary functions 3 Set the end time of your choice by pressing the End Time button End Time indicator illuminates 4 Press Start Pause button Time countdown starts sign in the middle of the end time on the display Starts flashing turns off washing cycle starts and the time of the selected programme appears on the display i Additional laundry may be loaded during the End Time countdown period At the end of the countdown End Time indicator When the End Time selection is completed the time appears on the screen consists of end time plus the duration of the selected programme 7 10 Starting the programme 1 Press Start Pause button to start the programme 2 The Start Pause button which was off before starts to illuminate steadily now indicating that the programme has started 88 1898 00 06 000 000000100 Pa Th 3 Loading door is locked The door lock symbol appears on the display after the loading door is locked gge o FP bm 1888 88 06 aN g h W g og i T N A Ra __ i E 4 Programme follow up indicator lights on the display will show the current programme step 7 11 Loading door lock There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable Door Locked symbol appears on the dis
10. smell like the softener Detergent is put in the wrong compartment If detergent is put in the prewash compartment although prewash cycle is not selected machine can take this detergent during rinsing or softener step Wash and clean the dispenser with hot water Put the detergent in the correct compartment Detergent might be mixed with the softener Do not mix the softener with detergent Wash and clean the dispenser with hot water Detergent residue in the detergent drawer Detergent is put in wet drawer Dry the detergent drawer before putting in detergent Detergent has gotten damp Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures Water pressure is low Check the water pressure The detergent in the main wash compartment got wet while taking in the prewash water Holes of the detergent compartment are blocked Check the holes and clean if they are clogged There is a problem with the detergent drawer valves Call the Authorized Service Agent Detergent might be mixed with the softener Do not mix the softener with detergent Wash and clean the dispenser with hot water Regular drum cleaning is not applied Clean the drum regularly For this please see 8 2 Too much foam forms in the machine Improper detergents for the washing machine are being us
11. speed selection Whenever a new programme is selected the recommended spin speed of the selected programme is displayed on the Spin Speed indicator It is possible that the recommended spin speed value is not the maximum spin speed that can be selected for the current programme Washing Machine User s Manual 19 EN 00000000 Press the Spin Speed Adjustment button to change the spin speed Spin speed decreases gradually Then depending on the model of the product Rinse Hold and No Spin options appear on the display Spin Speed Adjustment button only serves for decreasing the spin speed Rinse Hold option is indicated with 1_ symbol and No Spin option is indicated with _ symbol If you are not going to unload your laundry immediately after the programme completes you can use Rinse Hold function in order to prevent them from getting wrinkled when there is no water in the machine This function holds the laundry in the final rinsing water 00000000 100010040 If you want to spin your laundry after the Rinse Hold function Adjust the Spin Speed Press Start Pause Cancel button The programme resumes Machine spins the laundry by discharging the water If you want to discharge the water at the end of the programme without spinning use No Spin function _ s L 00000000 h 00000000 i No cha
12. the production This is not a failure water is not harmful to the machine Machine does not fill with water Tap is turned off Turn on the taps Water inlet hose is bent Flatten the hose Water inlet filter is clogged Clean the filter Loading door may be open Close the door Machine does not drain water Water drain hose might be clogged or twisted Clean or flatten the hose Pump filter is clogged Clean the pump filter Machine vibrates or makes noise Machine might be standing unbalanced Adjust the feet to level the machine A hard substance might have entered into the pump filter Clean the pump filter Transportation safety bolts are not removed Remove the transportation safety bolts Laundry quantity in the machine might be too little Add more laundry to the machine Machine might be overloaded with laundry Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine Machine might be leaning on a rigid item Make sure that the machine is not leaning on anything There is water leaking from the bottom of the washing machine Water drain hose might be clogged or twisted Clean or flatten the hose Pump filter is clogged Clean the pump filter Machine stopped shortly after the programme started Machine might have s
13. 1 13 90 120 45 40 Synthetics 40 4 69 0 90 80 110 45 40 You can see the washing time of the programme you have selected on the display of the machine It is normal that small differences may occur between the time shown on the display and the real washing time Remaining moisture content values may differ according to the selected spin speed 7 4 Programme selection 1 Determine the programme suitable for the type quantity and soiling level of the laundry in accordance with the Programme and consumption table i Programmes are limited with the highest spin speed appropriate for that particular type of fabric When selecting a programme always consider the type of fabric colour degree of soiling and permissible water temperature Always select the lowest required temperature Higher temperature means higher power consumption 2 Select the desired programme with the Programme Selection knob 7 5 Programmes e Cottons Use for your cotton laundry such as bed sheets duvet and pillowcase sets towels bathrobes underwear etc Your laundry will be washed with vigorous washing action for a longer washing cycle e Synthetics Use to wash your synthetic clothes shirts blouses synthetic cotton blends etc It washes with a gentle action and has a shorter washing cycle compared to the Cottons programme For curtains and tulle use the Synthetic 40 C programme
14. C and 40 C at full and partial load and the consumption of the low power modes Actual energy consumption will depend on how the appliance is used 2 Water consumption based on 220 standard washing cycles for cotton programmes at 60 C and 40 C at full and partial load Actual water consumption will depend on how the appliance is used Standard 60 C cotton programme and the standard 40 C cotton programme are the standard washing programmes to which the information in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption Technical specifications may be changed without prior notice to improve the quality of the product 6 EN Washing Machine User s Manual 5 Installation e Apply to the nearest authorized service agent for the installation of your product e Preparation of the location and electrical tap water and waste water installations at the place of installation is under customer s responsibility e Make sure that the water inlet and discharge hoses as well as the power cable are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures e Make sure that the installation and electrical connections of the product are performed by authorized service Manufacturer shall not be held liable for damages that
15. Lower mechanical movement in washing cycles and lower rpm in spinning cycles are used to prevent washing damages on stoned jeans as well as to ensure a longer life e Lingerie Use this programme to wash delicates such as underwears If there is little amount of laundry use a laundry net e Rinse Use when you want to rinse or starch separately e Spin Drain Use to drain the water in the machine 7 6 Temperature selection Whenever a new programme is selected the recommended temperature for the programme appears on the temperature indicator It is possible that the recommended temperature value is not the maximum temperature that can be selected for the current programme Press the Temperature Adjustment button to change the temperature Temperature will decrease by increments of 10 C Finally symbol indicating the cold wash option appears on the display 00000000 M i No change can be made in programmes where temperature adjustment is not allowed You can also change the temperature after the washing starts This change can be made if the washing steps allow it Changes cannot be made if the steps do not allow it If you scroll to cold wash option and press Temperature Adjustment button again the recommended maximum temperature for the selected programme appears on the display Press the Temperature Adjustment button again to decrease the temperature 7 7 Spin
16. ained about the safe use of the product and its risks Children should not play with the device Cleaning and maintenance works should not be performed by children unless they are supervised by someone Children of less than 3 years should be kept away unless continuously supervised gt Packaging materials may be dangerous for the children Keep packaging materials in a safe place away from reach of the children gt Electrical products are dangerous for the children Keep the children away from the product when it is in use Do not allow them to play with the product Use child lock to prevent children from intervening with the product Washing Machine User s Manual 3 EN gt gt Do not forget to close the loading door when leaving the room where the product is located Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package 1 3 Electrical safety gt gt gt gt lf the product has a failure it should not be operated unless it is repaired by the Authorized Service Agent Risk of electric shock This product is designed to resume operating in the event of powering on after a power interruption If you wish to cancel the programme see Cancelling the programme section Plug the product into a grounded outlet protected by a 13 A fuse Do not neglect to have the grounding installation made by a qua
17. all transportation safety bolts in the reverse order of removal procedure i Never move the product without the transportation safety bolts properly fixed in place WARNING Packaging materials are dangerous to children Keep packaging materials in a safe place away from reach of the children 5 8 Initial use Before starting to use the product make sure that the preparations are made which are in line with the Important Safety and Environment Instructions and the instructions in the Installation section To prepare the product for washing laundry perform first operation in Drum Cleaning programme If this program is not available in your machine apply the method which is described in the section 8 2 Use an anti limescale suitable for the washing machines i some water might have remained in the product due to the quality control processes in the production It is not harmful for the product 10 7 EN Washing Machine User s Manual 6 Preparation 6 1 Sorting the laundry Sort laundry according to type of fabric color and degree of soiling and allowable water temperature Always obey the instructions given on the garment tags 6 2 Preparing laundry for washing e Laundry items with metal attachments such as underwired bras belt buckles or metal buttons will damage the machine Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case e
18. amages that will arise when the product is used without grounding in accordance with the local regulations e Connection must comply with national regulations e Power cable plug must be within easy reach after installation lf the current value of the fuse or breaker in the house is less than 13 Amps have a qualified electrician install a 13 Amp fuse The voltage specified in the Technical specifications section must be equal to your mains voltage Do not make connections via extension cables or multi plugs A N WARNING Damaged power cables must be replaced by the Authorised Service Agents Electrical requirements Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position Should the mains lead of the appliance become damaged or need replacing at any time it must be replaced by a special purpose made mains lead which can only be obtained from a Authorised Service Agent A N WARNING This appliance must be earthed lf the fitted moulded plug is not suitable for your socket then the plug should be cut off and an appropriate plug fitted Destroy the old plug which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house The moulde
19. and soiling degree of the laundry Washing Machine User s Manual 29 EN Problem Reason Solution It does not rinse well The amount brand and storage conditions of the detergent used are inappropriate Use a detergent appropriate for the washing machine and your laundry Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures Detergent is put in the wrong compartment If detergent is put in the prewash compartment although prewash cycle is not selected machine can take this detergent during rinsing or softener step Put the detergent in the correct compartment Pump filter is clogged Check the filter Drain hose is folded Check the drain hose Laundry became stiff after washing Insufficient amount of detergent is used Using insufficient amount of detergent for the water hardness can cause the laundry to become stiff in time Use appropriate amount of detergent according to the water hardness Detergent is put in the wrong compartment If detergent is put in the prewash compartment although prewash cycle is not selected machine can take this detergent during rinsing or softener step Put the detergent in the correct compartment Detergent might be mixed with the softener Do not mix the softener with detergent Wash and clean the dispenser with hot water Laundry does not
20. ashing machine needs to be moved again in the future CAUTION Remove the transportation safety bolts before operating the washing machine Otherwise the product will be Install the transport safety bolts in reverse order of the disassembly procedure Never move the product without the transportation safety bolts properly fixed in place Washing Machine User s Manual 7 7 EN 5 4 Connecting water supply i The water supply pressure required to run the product is between 1 to 10 bars 0 1 1 MPa It is necessary to have 10 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly Attach a pressure reducing valve if water pressure is higher If you are going to use the double water inlet product as a single cold water inlet unit you must install the supplied stopper to the hot water valve before operating the product Applies for the products supplied with a blind stopper group CAUTION Models with a single water inlet should not be connected to the hot water tap In such a case the laundry will get damaged or the product will switch to protection mode and will not operate CAUTION Do not use old or used water inlet hoses on the new product It may cause stains on your laundry Connect the special water supply hoses supplied with the product to the water inlets on the product Red hose left max 90 C is for hot water inlet blue ho
21. aste product with normal domestic and other wastes at the end of its service life Take it to the collection center for the recycling of electrical and electronic equipment Please consult your local authorities to learn about these GE collection centers Compliance with RoHS Directive The product you have purchased complies with EU RoHS Directive 2011 65 EU It does not contain harmful and prohibited materials specified in the Directive 2 2 Package information Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities a Intended use e This product has been designed for domestic use It is not for commercial purposes or it should not be used out of its intended use e The product must only be used for washing and rinsing of laundry that are marked accordingly e The manufacturer waives any responsibility arisen from incorrect usage or transportation e The service life of your product is 10 years During this period original spare parts will be available to operate the appliance properly Washing Machine User s Manual 5 EN supplier name or trademark Model name Rated capacity kg Energy efficiency class Scale from A Highest Efficiency to D Lowest Efficiency An
22. belongs to allergic persons Longer heating time and an additional rinsing step provide a higher level of hygiene e BabyProtect 60 C programme is tested and approved by The British Allergy Foundation Allergy UK in United Kingdom e Delicate Use to wash your delicate clothes It washes with more gentle washing action compared to the Synthetics programme e Hand Wash Use to wash your woolen delicate clothes that bear not machine washable tags and for which hand wash is recommended It washes laundry with a very gentle washing action to not to damage clothes e 14 Minutes Use to wash your lightly soiled and unstained cotton laundry in a short time e Dark Wash Use this programme to wash your dark colored laundry or colored laundry that you do not want them get faded Washing is performed with little mechanic action and at low temperatures It is recommended to use liquid detergent or woolen shampoo for dark coloured laundry e Mixed Use this programme to wash your cotton and synthetic clothes together without sorting them e Steam Refresh To soften the soiling it pre treats the laundry by giving steam Load only half of the capacity stated for the selected programme When this programme is selected it is normal to hear boiling noises since the steam generator boils water to produce steam e Shirts Use to wash the shirts made of cotton synthetic and synthetic blended fabrics together e Sports Use this pr
23. d detergents recommended for colors can be used at dosages recommended for lightly soiled clothes Detergents which do not contain bleach should be used Liquid detergents suitable for colors and dark colors can be used at dosages recommended for lightly soiled clothes Prefer liquid detergents produced for delicate clothes Woolen and silk clothes must be washed with special woolen detergents 147 EN Washing Machine User s Manual A Operating the product 7 1 Control panel 1 2 3 4 5 C co co jam co Cc 4 co jam co Cc co co co 10 9 8 1 Programme Selection knob 6 On Off button 2 Spin speed adjustment button 7 Start Pause button 3 Temperature Adjustment button 8 End Time Setting button 4 Display 9 Auxiliary Function buttons 5 Program Follow up indicator 10 Programme Selection LEDs 7 2 Display symbols a b c doe f g Temperature indicator h Program Follow up indicator Electrical connection End Time indicator steam indicator j Duration Information Line Audio Warning indicator k Auxiliary Function indicators No Water indicator Lock indicator Detergent indicator m Spin Speed indicator Start Pause indicator aornDodand o m I i The visuals used for machine description in this section are schematic and may not match exactly will the features of your machine Washing Machine User s Manual 15 7 EN 7 3
24. d plug on this appliance incorporates a 13A fuse Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used Do not forget to refit the fuse cover In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug Fuse covers are available from any good electrical store Washing Machine User s Manual 9 EN Important Fitting a different plug Green and yellow or green As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug proceed as follows 1 Connect the green yellow or green earth wire to the terminal in the plug marked E or with the symbol f or coloured green and yellow or green 2 Connect the blue neutral wire to the terminal in the plug marked N or coloured black 3 Connect the brown live wire to the terminal in the plug marked L or coloured red With the alternative plugs a 13A fuse must be fitted either in the plug or _ adaptor or in the main fuse box If in doubt contact a qualified electrician Blue or Brown or black red Transportation of the product 1 Unplug the product before transporting it 2 Remove water drain and water supply connections 3 Drain all water that has remained in the product 4 Inst
25. ded to use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches Powder and liquid detergents recommended for colors can be used at dosages recommended for heavily soiled clothes It is recommended to use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches Use detergents without bleach Liquid detergents Suitable for colors and dark colors can be used at dosages recommended for heavily soiled clothes Prefer liquid detergents produced for delicate clothes Woolen and silk clothes must be washed with special woolen detergents Normally Soiled For example stains caused by body on collars and cuffs Powder and liquid detergents recommended for whites can be used at dosages recommended for normally soiled clothes Powder and liquid detergents recommended for colors can be used at dosages recommended for normally soiled clothes Detergents which do not contain bleach should be used Liquid detergents Suitable for colors and dark colors can be used at dosages recommended for normally soiled clothes Prefer liquid detergents produced for delicate clothes Woolen and silk clothes must be washed with special woolen detergents Lightly Soiled No visible stains exist Powder and liquid detergents recommended for whites can be used at dosages recommended for lightly soiled clothes Powder and liqui
26. e machine is high or the water level is above the door opening 7 13 Child Lock Use Child Lock function to prevent children from tampering with the machine Thus you can avoid any changes in a running programme You can switch on and off the machine with On Off button when the Child Lock is active When you switch on the machine again programme will resume from where it has stopped When the child lock is enabled an audio warning will be given if the buttons are pressed Audio warning will be canceled if the buttons are pressed 5 times consecutively To activate the Child Lock Press and hold Auxiliary Function button 2 for 3 seconds After the countdown as CL 3 2 1 on the display is over Child Lock Enabled appears on the display Release 2nd Auxiliary Function button when this warning is displayed To deactivate the childproof lock Press and hold Auxiliary Function button 2 for 3 seconds After the countdown as CL 3 2 1 on the display is over Child Lock Enabled disappears from the display Washing Machine User s Manual 23 EN 7 14 Cancelling the programme The programme is cancelled when the machine is turned off and on again Press and hold On Off button for 3 seconds After the countdown as 3 2 1 on the display is over the machine turns off i If you press On Off button when the Child Lock is enabled the programme will not be cancelled You should cancel the Child Lock fir
27. ed Use detergents appropriate for the washing machine Excessive amount of detergent is used Use only sufficient amount of detergent Detergent was stored under improper conditions Store detergent in a closed and dry location Do not store in excessively hot places Some meshed laundry such as tulle may foam too much because of their texture Use smaller amounts of detergent for this type of item Detergent is put in the wrong compartment Put the detergent in the correct compartment Softener is being taken early There may be problem in the valves or in the detergent dispenser Call the Authorized Service Agent Foam is overflowing from the detergent drawer Too much detergent is used Mix 1 tablespoonful softener and water and pour into the main wash compartment of the detergent drawer Put detergent into the machine suitable for the programmes and maximum loads indicated in the Programme and consumption table When you use additional chemicals stain removers bleachs and etc reduce the amount of detergent 30 EN Washing Machine User s Manual Problem Reason Solution Laundry remains wet at the end of Excessive foam might have occurred and automatic Use recommended amount of detergent the programme foam absorption system might have been activated due to too much detergent usage
28. ergent and softener When using detergent softener starch fabric dye bleacher and decolorant descaling agents read the manufacturer s instructions written on the package and follow the dosages specified Use measuring cup if available 0900 The detergent drawer is composed of three compartments 1 for prewash 2 for main wash 3 for softener in addition there is a siphon piece in the softener compartment ON eS aAA Detergent softener and other cleaning agents e Add detergent and softener before starting the washing programme e While the washing cycle is in progress do not leave the detergent dispenser open e When using a programme without prewash do not put any detergent into the prewash compartment compartment nr 1 e n a programme with prewash do not put liquid detergent into the prewash compartment compartment nr ga e Do not select a programme with prewash if you are using a detergent bag or dispensing ball Place the detergent bag or the dispensing ball directly among the laundry in the machine If you are using liquid detergent do not forget to place the liquid detergent container into the main wash compartment compartment number 2 Choosing the detergent type Detergent type to be used depends on the fabric type and color e Use different detergents for coloured and white laundry e Wash your delicate clothes only with special detergents liquid detergent wool shampoo
29. gy consumption and programme time See the programme description for maximum load Cotton eco 40 C and Cotton eco 60 C are standard programmes These programmes are known as 40 C cotton standard programme and 60 C cotton standard programme and indicated with the lt 60 symbols on the panel Water and power consumption may vary subject to the changes in water pressure water hardness and temperature ambient i The auxiliary functions in the table may vary according to the model of your machine temperature type and amount of laundry selection of auxiliary functions and spin speed and changes in electric voltage You can see the washing time of the programme you have selected on the display of the machine It is normal that small differences may occur between the time shown on the display and the real washing time Selection patterns for auxiliary functions can be changed by the manufacturer company New selection patterns can be added or removed The spin speed of your machine may vary according to the programme this spin speed cannot exceed the max spin speed of your machine 16 EN Washing Machine User s Manual Indicative values for Synthetics programmes EN S 1 Remaining Moisture Content Remaining Moisture Content S S v E pe B 2 D gt 5 x E 2 S22 S87 2e SSz EaeE lt 1000 rpm gt 1000 rpm synthetics 60 4 65
30. ine Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum The machine will not spin if water is not drained completely Check the filter and the draining hose Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage Use recommended amount of detergent Washing performance is poor Laundry turns gray Insufficient amount of detergent has been used over a long period of time Use the recommended amount of detergent appropriate for water hardness and the laundry Washing was made at low temperatures for a long time Select the proper temperature for the laundry to be washed Insufficient amount of detergent is used with hard water Using insufficient amount of detergent with hard water causes the soil to stick on the cloth and this turns the cloth into gray in time It is difficult to eliminate graying once it happens Use the recommended amount of detergent appropriate for water hardness and the laundry Too much detergent is used Use the recommended amount of detergent appropriate for water hardness and the laundry Washing performance is poor Stains persist or the laundry is not whitened Insufficient amount of detergent is used Use the recommended amount of detergent appropriate for water hardness and the
31. ine fails to drain water the pump filter is clogged Filter must be cleaned whenever it is clogged or in every 3 months Water must be drained off first to clean the pump filter CAUTION if the product is not being used shut the tap shut remove mains pipe and drain the water inside the machine against any likely freezing CAUTION After each use turn off the water tap to which the mains hose is connected In order to clean the dirty filter and discharge the water 1 Unplug the machine to cut off the supply power CAUTION Temperature of the water inside the machine may rise up to 90 C To avoid the burning risk clean the filter after the water inside the machine is cooled down 2 Open the filter cover 3 Follow the below procedures in order to drain water If the product has an emergency water draining hose in order to drain the water a Pull the emergency draining hose out from its seat b Place a large container at the end of the hose Drain the water into the container by pulling out the plug at the end of the hose When the container is full block ba the inlet of the hose by replacing the plug After the Come container is emptied repeat the above procedure to drain the water in the machine completely c When draining of water is finished close the end by the plug again and fix the hose in its place d Turn and remove the pump filter 26 EN Washing Machine User s Manual If
32. lified electrician Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations Do not wash the product by spraying or pouring water onto it Risk of electric shock Never touch the power cable plug with wet hands Do not grab the power cord to unplug the machine always unplug it by holding the socket with one hand and pulling the plug with the other hand Product should be unplugged during installation maintenance cleaning and repair procedures lf the power cable is damaged it must be replaced by the manufacturer after sales service or a similarly qualified person preferably an electrician or someone designated by the importer in order to avoid possible risks 1 4 Hot surface safety While washing the laundry at high temperatures the loading door glass will get hot Considering this fact during washing operation keep the children away from the loading door of the product to prevent them touching it 4 EN Washing Machine User s Manual 2 Important instructions for environment 2 1 Compliance with WEEE Directive This product complies with EU WEEE Directive 2012 19 EU This product bears a classification symbol for waste electrical and electronic equipment WEEE This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling Do not dispose of the w
33. may arise from procedures carried out by unauthorized persons e Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products cause risks for your safety 5 1 Appropriate installation location e Place the product on a hard and level floor Do not put it onto a carpet with high pile or other similar surfaces e When the washing machine and drier are placed on top of each other their total weight when loaded amounts to 180 kilograms Place the product on a solid and flat floor that has sufficient load carrying capacity Do not place the product on the power cable Do not install the product in the environments where the temperature falls below 0 C Leave a minimum space of 1 cm between the machine and the furniture On a graduated floor do not place the product next to the edge or on a platform 5 2 Removing packaging reinforcement Tilt the machine backwards to remove the packaging reinforcement Remove the packaging reinforcement by pulling the ribbon Do not make this operation alone by yourself 5 3 Removing the transportation locks 1 Loose all bolts with an appropriate wrench until they turn freely C 2 Remove the transport safety bolts by turning them slightly 3 Insert the plastic covers in the bag containing the user manual to the openings on the rear panel P damaged Keep the transportation safety bolts in a safe place to reuse when the w
34. nge can be made in programmes where spin speed adjustment is not allowed You can change the spin speed after the washing starts if the washing steps allow it Changes cannot be made if the steps do not allow it 7 8 Auxiliary function selection select the desired auxiliary functions before starting the programme Whenever a programme is selected frames of the auxiliary function symbol that can be selected together with it illuminates And when you select an auxiliary function the interior area of the auxiliary function symbol also starts to illuminate In we 00000000 r Frame of the auxiliary function symbol that cannot be selected with the current programme does not illuminate 20 EN Washing Machine User s Manual Also the frames of the auxiliary function suitable for the current programme after the washing has started remains illuminated You can select or cancel the auxiliary functions whose frames are illuminated If the wash cycle has reached a point where you cannot select the auxiliary function the function s frame turns off i some functions cannot be selected together If a second auxiliary function conflicting with the first one is selected before starting the machine the function selected first will be canceled and the second auxiliary function selection will remain active For example if you want to select Quick Wash after you have selected the Additional Water Addi
35. nstructions are not observed 1 1 Life and property safety gt Never place the product on a carpet covered floor Electrical parts will get overheated since air cannot circulate from under the device This will cause problems with your product gt Unplug the product if it is not in use gt Always have the installation and repairing procedures carried out by the Authorized Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons gt The water supply and draining hoses must be securely fastened and remain undamaged Otherwise water leak may occur gt While there is still water inside the product never open the loading door or remove the filter Otherwise risk of flooding and injury from hot water will occur gt Do not force open the locked loading door Door can be opened a few minutes after the washing cycle ends In case of forcing the loading door to open the door and the lock mechanism may get damaged gt Use detergents softeners and supplements suitable for automatic washing machines only gt Follow the instructions on the label of textiles and the detergent package 1 2 Children s safety gt This product can be used by the children who are at the age of 8 and over and the people whose physical sensory or mental skills are not fully developed or who do not have necessary required experience and knowledge as long as they are supervised or tr
36. nual Energy Consumption kWh Energy consumption of the standard 60 C cotton programme at full load kWh Energy consumption of the standard 60 C cotton programme at partial load kWh Energy consumption of the standard 40 C cotton programme at partial load kWh Power consumption in off mode W Power consumption in left on mode W Annual Water Consumption I Spin drying efficiency class Scale from A Highest Efficiency to G Lowest Efficiency Maximum spin speed rpm Remaining moisture Content Standard cotton programme Programme time of the standard 60 C cotton programme at full load min Programme time of the standard 60 C cotton programme at partial load min Programme time of the standard 40 C cotton programme at partial load min Duration of the left on mode min Airborne acoustical noise emissions washing spinning dB Built in Height cm Width cm Depth cm Net weight 4 kg single Water inlet Double Water inlet e Available Electrical input V Hz Total current A Total power W Main model code 4 Technical specifications Complying Commission Delegated Regulation EU No 1061 2010 SMEG WHT914LSUK 9 A 214 1 060 0 900 0 840 0 440 0 640 10560 B 1400 33 Cotton Eco 60 C and 40 C 224 190 190 N A 53 76 No 84 60 60 75 e 230 V 50Hz 10 2200 978 Energy Consumption based on 220 standard washing cycles for cotton programmes at 60
37. o33 SMEG WHT914LSUK Washing Machine User s Manual Document Number 2820524426 EN 12 12 14 16 10 Please read this user manual first Dear Customer Thank you for prefering a product We hope that you get the best results from your product which has been manufactured with high quality and state of the art technology Therefore please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use If you handover the product to someone else give the user manual as well Follow all warnings and information in the user manual Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this user manual the following symbols are used Important information or useful hints about usage Warning for hazardous situations with regard to life and property Warning for electric shock Recyclable materials OPPA Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities 2 EN Washing Machine User s Manual 1 General safety instructions This section includes security instructions which may help prevent the injuries and material damage risks All kinds of warranties shall be invalid if these i
38. ogramme to wash your garments that are worn for a short time such as sportswear It is suitable to wash little amount of cotton synthetic blended garments e Curtains Use this programme to wash your tulles and curtains Thanks to the special spin profile of the programme tulles and curtains crease lesser As their meshed texture causes excessive foaming wash the veils tulle by putting little amount of detergent into the main wash compartment Do not put detergent in the prewash compartment It is recommended to use special detergents produced for curtains in this programme e Duvet Use this programme to wash your fiber duvets that bear machine washable tag Make sure that you have loaded the duvet correctly in order not to damage the machine and the duvet Remove the duvet cover before loading the duvet into the machine Fold the duvet into two and load it into the machine Load the duvet into the machine paying attention to place it in a way that it will not contact the bellow i Do not load more than 1 double fibre duvet 200 x 200 cm Do not wash your duvets pillows and etc that contain cotton in the machine 18 EN Washing Machine User s Manual CAUTION Do not wash the items apart from duvets such as carpets rugs and etc in the machine Permanent damage occurs in the machine e Jeans Use this programme to wash clothes such as trousers jackets vests etc made of denim
39. play when the loading door is locked 22 EN Washing Machine User s Manual 7 12 Changing the selections after programme has started Adding laundry after the programme has started lf the water level in the machine is suitable when you press Start Pause button loading door symbol will flash on the display until the loading door is opened and will disappear when the loading door is opened If the water level in the machine is not suitable when you press Start Pause button the loading door symbol remain lit on the display na 1898 88 88 Switching the machine to pause mode Press the Start Pause button to switch the machine to pause mode Pause symbol will flash on the display a FF I 7 Ce 188 08 08 Changing the programme selection after programme has started The programme change is not allowed when the current programme is running You can select the new programme after switching the current programme to pause mode i The selected program starts anew Changing the auxiliary function speed and temperature Depending on the step the programme has reached you can cancel or activate the auxiliary functions See Auxiliary function selection You can also change the speed and temperature settings See Spin speed selection and Temperature selection i The loading door will not open if the water temperature in th
40. se right max 25 C is for cold water inlet Make sure that the hot and cold water taps are connected correctly when the product is being installed Otherwise your laundry will come out hot at the end of the washing process and wear out 1 Tighten the nuts of the hose by hand Never use a tool when tightening the nuts 2 When hose connection is completed check whether there is leak problems at the connection points by opening the taps fully If any leaks occur turn off the tap and remove the nut Retighten the nut carefully after checking the seal In order to prevent the water leaks and resultant damages keep the taps closed when you do not use the product 5 5 Connecting the drain hose to the drain e Attach the end of the drain hose directly to waste water drain lavatory or bathtub A CAUTION Your drain house will be flooded if the hose comes out of its housing during water discharge Moreover there is risk of scalding due to high washing temperatures In order to prevent such situations and make sure that the machine performs water intake and discharge processes without any problem fix the drain hose securely and a maximum height of 100 cm e n case the drain hose is elevated after laying it on the floor level or close to the ground less than 40 cm above the ground water discharge becomes more difficult and the laundry may come out excessively wet Therefore follow the heights described
41. se bleaching agent and detergent by mixing them e Use just a little amount approx 50 ml of bleaching agent and rinse the clothes very well as it causes skin irritation Do not pour the bleach onto the laundry and do not use it with the colored items e When using oxygen based decolorant select a program which washes the laundry at a low temperature e Qxygen based decolorant can be used with the detergent however if it is not at the same consistence first put detergent in the compartment number 2 in the detergent dispenser and wait for the machine to flush the detergent when taking in water While the machine continues taking in water add decolorant in the same compartment Washing Machine User s Manual 13 7 EN 6 7 Tips for efficient washing Clothes D gt D I D Sp Recommended temperature range based on soiling level 40 90 90 Recommended temperature range based on soiling level cold 40 temperature range based on sailing level cold 40 C Light Colours and Colour Black Dark Delicates Whites Colours Woolens Silks Recommended Recommended temperature range based on soiling level cold 30 C Heavily Soiled difficult stains such as grass coffee fruits and blood It may be necessary to pre treat the stains or perform prewash Powder and liquid detergents recommended for whites can be used at dosages recommended for heavily soiled clothes It is recommen
42. st If you want to open the loading door after you have cancelled the programme but it is not possible to open the loading door since the water level in the machine is above the loading door opening then turn the Programme Selection knob to Pump spin programme and discharge the water in the machine 7 15 End of programme End symbol appears on the display when the programme is completed If you do not press any button for 10 minutes the machine will switch to OFF mode Display and all indicators are turned off Completed programme steps will be displayed if you press On Off button 7 16 Adjusting the VOLUME level Low volume and high volume Press and hold Auxiliary Function button 3 for 3 seconds to adjust the volume level After the countdown as 3 2 1 on the display is over the volume level symbol will appear and the new volume level will be displayed 7 17 Memory programme setting You can create a Memory programme by saving frequently used programme and other settings Use this function when you want to select quickly the same settings you use for the laundry that you wash regularly Memory programme will remain at the factory set programme until you make a new Memory programme setting To store a new Memory programme 1 Select the desired programme temperature spin speed soiling degree and auxiliary function 2 Press and hold the Memory button for 3 seconds 3 Countdown as 3 2 1 appears on the display to select a Memor
43. stated for the selected programme When this auxiliary function is selected it is normal to hear boiling noises since the steam generator boils water to produce steam Time display Remaining time for the completion of the programme while it is running is displayed as 01 30 in hours and minutes format water hardness and temperature ambient temperature amount and the type of laundry auxiliary functions selected and the i Programme time may differ from the values in the Programme and consumption table depending on the water pressure changes at the mains voltage 7 9 End Time With the End Time function the startup of the programme may be delayed up to 24 hours After pressing End Time button the programme s estimated ending time is displayed If the End Time is adjusted End Time indicator is illuminated Washing Machine User s Manual 21 EN In order for the End Time function is activated and the programme is completed at the end of the specified time you must press Start Pause button after adjusting the time If you want to cancel End Time function press On Off button to turn off and on the machine i Do not use liquid detergents when you activate End Time function There is the risk of staining of the clothes 1 Open the loading door place the laundry and put detergent etc 2 select the washing programme temperature spin speed and if
44. the product does not have an emergency water drain hose in order to drain the water a In order to collect the water to flow out of the filter place a large vessel in front of the filter b Turn and loosen the pump filter until water starts to flow counterclockwise Fill the flowing water into the container you have placed in front of the filter Always keep a piece of cloth handy to absorb any spilled water c When the water inside the machine is finished take out the filter completely by turning it 4 Clean any residues inside the filter as well as fibers if any around the pump impeller region 5 Replace the filter 6 If the filter cap is composed of two pieces close the filter cap by pressing on the tab If it is one piece seat the tabs in the lower part into their places first and then press the upper part to close Washing Machine User s Manual 27 EN E Troubleshooting Problem Reason Solution Program does not start after closing the door Start Pause Cancel button was not pressed Press the Start Pause Cancel button Programme cannot be started or selected Washing machine has switched to self protection mode due to a supply problem line voltage water pressure etc Press and hold On Off button for 3 seconds see Cancellation of program Water in the machine Some water might have remained in the product due to the quality control processes in
45. tional Water will be canceled and Quick Wash will remain active An auxiliary function that is not compatible with the programme cannot be selected See Programme and consumption table some programmes have auxiliary functions that must be operated simultaneously Those functions cannot be cancelled The frame of the auxiliary function will not be illuminated only inner area will be illuminated e Prewash A Prewash is only worthwhile for heavily soiled laundry Not using the Prewash will save energy water detergent and time e Quick Wash This function can be used in Cottons and Synthetics programmes It decreases the washing times and also the number of rinsing steps for lightly soiled laundry i When you select this function load your machine with half of the maximum laundry specified in the programme table e Extra Rinse This function enables the machine to make another rinsing in addition to the one already made after the main wash Thus the risk for sensitive skins babies allergic skins etc to be effected by the minimal detergent remnants on the laundry can be reduced e Anti Crease This function creases the clothes lesser when they are being washed Drum movement is reduced and spin speed is limited to prevent creasing In addition washing is done with a higher water level e Vapor Steam To soften the soiling it pre treats the laundry by giving steam i Load only half of the capacity
46. topped temporarily due to low voltage t will resume running when the voltage restores to the normal level Machine directly discharges the water it takes in Draining hose might not be at adequate height Connect the water draining hose as described in the operation manual No water can be seen in the machine during washing The water level is not visible from outside of the washing machine This is not a failure Loading door cannot be opened Door lock is activated because of the water level in the machine Drain the water by running the Pump or Spin programme Machine is heating up the water or it is at the spinning cycle Wait until the programme completes Child lock is engaged Door lock will be deactivated a couple of minutes after the programme has come to an end Wait for a couple of minutes for deactivation of the door lock Washing takes longer time than specified in the manual Water pressure is low Machine waits until taking in adequate amount of water to prevent poor washing quality due to the decreased amount of water Therefore the washing time extends Voltage might be low Washing time is prolonged to avoid poor washing results when the supply voltage is low Input temperature of water might be low Required time to heat up the water extends in cold seasons Also washing time can be lengthened to avoid poor washing res
47. ults Number of rinses and or amount of rinse water might have increased Machine increases the amount of rinse water when good rinsing is needed and adds an extra rinsing step if necessary Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage Use recommended amount of detergent 28 EN Washing Machine User s Manual Problem Reason Solution Programme time does not countdown On models with display Timer may stop during water intake Timer indicator will not countdown until the machine takes in adequate amount of water The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water Timer indicator will resume countdown after this Timer may stop during heating step Timer indicator will not countdown until the machine reaches the selected temperature Timer may stop during spinning step Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum Programme time does not countdown There might be unbalanced load in the machine Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum Machine does not switch to spinning step There might be unbalanced load in the mach
48. um Select Additional Water or Extra Rinse auxiliary functions Use a Cottons programme without pre wash Set the temperature to the level recommended on the drum cleaning agent which can be provided from authorized services Apply this procedure without any laundry in the product Before starting the programme put 1 pouch of special drum cleaning agent if the special agent could not be supplied put max 100 g of powder anti limescale into the main wash detergent compartment compartment no 2 If the anti limescale is in tablet form put only one tablet into the main wash compartment no 2 Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end Repeat Drum Cleaning process in every 2 months i Use an anti limescale suitable for the washing machines After every washing make sure that no foreign substance is left in the drum If the holes on the bellow shown in the figure is blocked open the holes using a toothpick Foreign metal substances will cause rust stains in the drum Clean the stains on the drum surface by using cleaning agents for stainless steel Never use steel wool or wire wool These will damage the painted chromated and plastic surfaces 8 3 Cleaning the body and control panel Wipe the body of the machine with soapy water or non corrosive mild gel detergents as necessary and dry with a soft cloth Use only a soft and damp cloth to clean the control panel
49. with prewash and anti creasing functions selected As their meshed texture causes excessive foaming wash the veils tulle by putting little amount of detergent into the main wash compartment Do not put detergent in the prewash compartment e Wool Use to wash your woolen clothes Select the appropriate temperature complying with the tags of your clothes Use appropriate detergents for woolens The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of machine washable wool products provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M14035 WOOLMARK Pe ee APPAREL a In UK Eire Hong Kong and India the Woolmark trade mark is a Certification trade mark Washing Machine User s Manual 177 EN e Cotton Eco Use to wash your normally soiled durable cotton and linen laundry Although it washes longer than all other programmes it provides high energy and water savings Actual water temperature may be different from the Stated wash temperature When you load the machine with less laundry e g 2 capacity or less programme time may automatically get shorter In this case energy and water consumption will decrease more providing a more economic wash This programme is available in the models with the remaining time indicator e HygieneCare Use to wash baby laundry and the laundry that
50. y allowed by the programme you have selected but do not overload see Programme and consumption table See Programme and consumption table e Always follow the instructions on the detergent packaging Wash slightly soiled laundry at low temperatures Use faster programmes for small quantities of lightly soiled laundry Do not use prewash and high temperatures for laundry that is not heavily soiled or stained If you plan to dry your laundry in a dryer select the highest spin speed recommended during washing process e Do not use more detergent than the recommended amount specified on its package 6 4 Loading the laundry 1 Open the laundry cover 2 Put the laundry items into the machine in a loose manner 3 Push and close the loading cover until you hear the locking sound Ensure that no items are caught in the door The loading door is locked while a programme is running The door can only be opened a while after the programme comes to an end 6 5 Correct load capacity The maximum load capacity depends on the type of laundry the degree of soiling and the washing programme desired Machine automatically adjusts the water amount according to the weight of the laundry put inside it WARNING Follow the information in the Programme and consumption table When overloaded machine s washing performance will drop Moreover noise and vibration problems may occur Washing Machine User s Manual 11 7 EN 6 6 Using det
51. y programme 1 Press Memory button The Memory selection field will be activated on the display 2 The programme saved as Memory and other settings will be displayed 3 Press the Start Pause button to start the Memory programme 24 EN Washing Machine User s Manual ES Maintenance and cleaning Service life of product extends and frequently experienced problems will be reduced if it is cleaned at regular intervals 8 1 Cleaning the detergent drawer Clean the detergent drawer at regular intervals every 4 5 washing cycles as shown below in order to prevent accumulation of powder detergent in time Lift the rear part of the siphon to remove it as illustrated If more than normal amount of water and softener mixture starts to gather in the softener compartment the siphon must be cleaned 1 Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine 2 Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin In order to prevent the residues to contact your skin clean it with an appropriate brush by wearing a pair of gloves 3 Insert the drawer back into its place after cleaning and make sure that it is seated well 8 2 Cleaning the loading door and the drum For products with drum cleaning programme please see Operating the product Programmes For products without drum cleaning follow the below steps to clean the dr
Download Pdf Manuals
Related Search