Zanussi ZGG67412WA hob
Contents
1. MANUAL ZGG67412 ZANUSSI Contents Safety information _______________ 2 Care and cleaning ____2_2 222 2 ______ 7 Safety instructions ______________ 3 Troubleshooting________________ 8 Product description 5 Installation _________________ 9 Daily use _ _ 2 ooo coco 5 Technical information 13 Helpful hints and tips 6 Environment concerns _______ 14 Subject to change without notice Safety information Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incor rect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety A Warning Risk of suffocation injury or permanent disability This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental ca pabilities or lack of experience and knowledge if they are super vised by an adult or a person who is responsible for their safety Do not let children play with the appliance Keep all packaging away from children Keep children and pets away from the appliance when it operates or when it cools down Accessible parts are hot If the appliance has a child safety device we recommend that you activate it Cleaning and user maintenance shall not be made by children without supervision General Safety The2. Regulations and local Electricity Board regulations For your own safety the in stallation must be done by a qualified electrician e g your local Electricity Board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting NICEIC www zanussi com The manufacturer refuses to be held responsible if these safety measures are not abided by Supply connections This hob has to be connected to 230 240 V 50 Hz electricity supply The hob has a terminal block which is marked as follows L Live terminal N Neutral terminal or E Earth terminal Before carrying out the connection make sure 1 The limiter valve and the electrical system can take the appliance load see the rating plate 2 The supply system is equipped with an effi cient earth connection in compliance with the current standards and regulations 3 The outlet or omnipolar switch used for connection is easily accessible with the ap pliance installed The appliance is supplied with a 3 core flexible powercable with a 3 amp plug If it is necessary to change the fuse use a 3 amp ASTA ap proved BS 1362 fuse A Green and Yellow B 3 amp fuse C Brown D Cord clamp E Blue The wires in the cord are coloured as follows 11 Green and yellow Earth Blue Neutral Brown Live Replacement of the connection cable 1 Connect the green and yellow
3. earth wire to the terminal which is marked with the let ter E or the earth symbol or coloured green and yellow 2 Connect the blue neutral wire to the ter minal which is marked with the letter N or coloured blue 3 Connect the brown live wire to the termi nal which is marked with the letter L It must always be connected to the network phase There must be no cut or stray strands of wire present The cord clamp must be correctly at tached to the outer sheath i To replace the connection cable use only HO5V2V2 F T90 or equivalent type Make sure that the cable section is applicable to the voltage load and the working temperature The yellow green earth wire B must be approxi mately 2 cm longer than the live and neutral wire A Warning A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely Important The replacement of electric cable must be carried out exclusively by the service force centre or by personnel with similar competencies in accordance with the current regulations 12 Building In g __ min 600 m N min 100 mm min 650 mm O a N W Pi A supplied seal B supplied bracket Caution Install the appliance only on a worktop with flat surface Possibilities for insertion Kitchen unit with door The panel installed below the hob must b
4. Scratches or dark stains on the surface have no effect on how the appliance oper ates You can remove the pan supports to easily clean the hob To clean the enamelled parts cap and crown wash them with warm soapy water and dry them carefully before you put them back Wash stainless steel parts with water and then dry them with a soft cloth The pan supports are not dishwasher proof They must be washed by hand www zanussi com Warning Make sure that pot handles is not above the front edge of the cooktop Make sure that pots are centrally put on the rings in order to get maximum stability and to get lower gas consumption Do not put unstable or damaged pots on the rings to prevent from spill and injury A Warning Do not use a flame diffuser The enamel coating occasionally can have rough edges so be careful when you wash the pan supports by hand and dry them If necessary remove stubborn stains with a paste cleaner Make sure you position the pan supports cor rectly after cleaning To make the burners work correctly make sure that the arms of the pan supports are in the centre of the burner Be very careful when you replace the pan supports to prevent the hob top from damage After cleaning dry the appliance with a soft cloth Removing the dirt 1 Remove immediately melting plastic plastic foil and food containing sugar Stop the appliance and let i
5. moved from the holder earth leakage trips and contactors Gas connection All gas connections should be made by a qualified person Before installation make sure that the local distribution conditions nature of the gas and gas pressure and the adjustment of the ap pliance are compatible Make sure that there is air circulation around the appliance The information about the gas supply is on the rating plate This appliance is not connected to a device which evacuates the products of combustion Make sure to connect the appliance accord ing to current installation regulations Pay at tention to requirements regarding adequate ventilation Use Warning Remove all the packaging labelling and protective film before first use Warning Risk of injury burns or electric shock Use this appliance in a household environ ment Do not change the specification of this appli ance Do not let the appliance stay unattended dur ing operation Do not operate the appliance with wet hands or when it has contact with water Do not put cutlery or saucepan lids on the cooking zones They become hot Set the cooking zone to off after use Do not use the appliance as a work or as a storage surface When you place food into a hot oil it may splash A Warning Risk of fire or explosion 4 Fats and oil when heated can release flam mable vapours Keep flames or heated ob jects away from fats and oils
6. when you cook with them The vapours that very hot oil releases can cause spontaneous combustion Used oil that can contain food remnants can cause fire at a lower temperature than oil used for the first time Do not put flammable products or items that are wet with flammable products in near or on the appliance Warning Risk of damage to the appliance Do not keep hot cookware on the control panel Do not let cookware to boil dry Do not activate the cooking zones with empty cookware or without cookware Do not put aluminium foil on the appliance Do not let acid liquids for example vinegar lemon juice or limescale remover touch the hob This can cause matt patches This appliance is for cooking purposes only Do not use the appliance for other purposes as for example room heating The use of a gas cooking appliance results in the production of heat and moisture Provide good ventilation in the room where the appli ance is installed Make sure that the ventilation openings are not blocked Prolonged intensive use of the appliance may call for additional ventilation for example opening of a window or more effective venti lation for example increasing the level of me chanical ventilation where present Use only stable cookware with the correct shape and diameter larger than the dimen sions of the burners There is a risk of over heating and rupture of the glass plate if ap plicable Make su
7. 30 37 mbar NORMAL RE G30 G31 BURNER POWER LU 28 30 mbar 37 mbar 1 100 mm kW g h g h Auxiliary 71 Semi rapid 2 0 71 145 143 Rapid 2 8 86 204 200 Environment concerns x The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and Packaging material electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product The packaging materials are friendly to the environment and can be recycled The plastic components are identified by marking gt PE lt gt PS lt etc Discard the packaging mate rials as household waste at the waste disposal facilities in your municipality 14 www zanussi com www zanussi com 15 www zanussi com shop e ee E 12 My fN 397305504 A 122013
8. alled in the Republic of Ire land please refer to the NSAI Domestic Gas In stallation I S 813 Current Editions Table Four Location The hob may be located in a kitchen a kitchen diner or bed sitting room with a volume greater 9 than 20 m3 but not in a bathroom or shower room The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob For appliances installed in the Republic of Ire land please refer to NSAI Domestic Gas Instal lation 1 5 813 Current Edition Section 7 Per mitted Locations of Appliance Gas Connection Warning Any gas installation must be carried out by a GAS SAFE REGISTER installer Make sure that once the hob is installed it is easily accessible for the engineer in the event of a breakdown The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored On the end of the shaft which includes the G 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts together without using excessive force gt CSS Q O c A A End of shaft with nut B Washer C Elbow Connection to the gas supply should be with ei ther rigid or semi rigid pipe i
9. ant In the absence of electricity you can ignite the burner without electrical device in this case approach the burner with a flame push the relevant knob down and turn it counter clockwise to maximum gas release position If the burner accidentally goes out turn the control knob to the off position and try to light the burner again after minimum 1 minute The spark generator can start automatically when you switch on the mains after instal lation or a power cut It is normal Turning the burner off To put the flame out turn the knob to the sym bol Warning Always turn the flame down or switch it off before you remove the pans from the burner When the liquid starts to boil turn down the flame to barely simmer the liquid www zanussi com Warning Use cookware with diameters applicable to the size of burners Bumer Diameters of cookware Rapid 180 260 mm Rear left semi 120 220 mm rapid Rear right semi 120 220 mm rapid Auxiliary 80 180 mm Warning Make sure that the bottoms of pots do not stand above the control knobs If the control knobs are under the bottoms of pots the flame heats them up Do not put the same pan on two burners P xs Care and cleaning A Warning Refer to the Safety chapters Warning Deactivate the appliance and let it cool down before you clean it Disconnect the appliance from the electrical supply before you do cleaning or maintenance work
10. appliance and its accessible parts become hot during use Do not touch the heating elements Do not operate the appliance by means of an external timer or separate remote control system 2 www zanussi com Unattended cooking on a hob with fat or oil can be dangerous and may result in fire Never try to extinguish a fire with water but switch off the appli ance and then cover flame e g with a lid or a fire blanket Do not store items on the cooking surfaces Do not use a steam cleaner to clean the appliance Metallic objects such as knives forks spoons and lids should not be placed on the hob surface since they can get hot A Safety instructions Installation Warning Only a qualified person must install this appliance Remove all the packaging Do not install or use a damaged appliance Obey the installation instruction supplied with the appliance Keep the minimum distance from the other appliances and units Always be careful when you move the appli ance because it is heavy Always wear safety gloves Seal the cut surfaces with a sealant to pre vent moisture to cause swelling Protect the bottom of the appliance from steam and moisture Do not install the appliance adjacent to a door or under a window This prevents hot cookware to fall from the appliance when the door or the window is opened If the appliance is installed above drawers make sure that the space between the bot tom of the applian
11. ce and the upper drawer is sufficient for air circulation The bottom of the appliance can get hot We recommend to install a non combustile sepa ration panel under the appliance to prevent access to the bottom www zanussi com Electrical connection A Warning Risk of fire and electrical shock All electrical connections must be made by a qualified electrician The appliance must be earthed Before carrying out any operation make sure that the appliance is disconnected from the power supply Use the correct electricity mains cable Do not let the electricity mains cable tangle Make sure the mains cable or plug if applica ble does not touch the hot appliance or hot cookware when you connect the appliance to the near sockets Make sure the appliance is installed correctly Loose and incorrect electricity mains cable or plug if applicable can make the terminal be come too hot Make sure that a shock protection is installed Use the strain relief clamp on cable Make sure not to cause damage to the mains plug if applicable or to the mains cable Contact the Service or an electrician to change a damaged mains cable The electrical installation must have an isola tion device which lets you disconnect the ap pliance from the mains at all poles The isola tion device must have a contact opening width of minimum 3 mm Use only correct isolation devices line pro tecting cut outs fuses screw type fuses re
12. compliance with standards and local regulations in force Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regula tions Current Edition and the IEE Wiring Reg ulations Current Edition For appliances installed in the Republic of Ire land please refer to NSAI Domestic Gas Instal lation l S 813 Current Editions and the ETCI Rules for Electrical Installations Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions www zanussi com C 0049 03 IT MADE IN ITALY MOD TYPE PROD NO 230V 50Hz SER NO IP20 C Stick it on instruction booklet The hob should not be installed in a bed sitting room with a volume of less than 20 ma If it is in stalled in a room of volume less than 5 m3 an air vent of effective area of 100 cm is required If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm is required while if the volume exceeds 11 m no air vent is required However if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m8 If there are other fuel burning appliances in the same room B S 5440 Part 2 Current Edition should be consulted to determine the requisite air vent requirements For appliances inst
13. e steel or copper The connection should be suitable for connect ing to R 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installation 10 Make sure that the main connection pipe does not exert any strain on the hob If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards Be careful they do not come in touch with mobile parts or they are not squeezed Also be careful when the hob is put together with an oven Important It is important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Important Failure to ensure the correct assembly will cause leakage of gas Important Make sure that the gas supply pressure of the appliance obeys the recommended values Rigid connection Carry out connection by using metal rigid pipes copper with mechanical end Injectors replacement 1 Remove the pan supports 2 Remove the caps and crowns of the burner 3 With a socket spanner 7 remove the injec tors and replace them with the ones which are necessary for the type of gas you use see table in Technical Information chap ter 4 Assemble the parts follow the same proce dure backwards 5 Replace the rating plate it is near the gas supply pipe with the one for the new type of gas supply You can find this plate in the package
14. e easy to remove and let an easy access in case a technical assistance intervention is necessary A Removable panel B Space for connections www zanussi com must be installed separately for safety reasons and to let easy remove oven from the unit Kitchen unit with oven The hob recess dimensions must obey the indi cation and the kitchen unit must be equipped with vents to let a continuous supply of air The E y i gt gt 2 a gt gt A 2 electrical connection of the hob and the oven 50 cm 120 cm 4 A P 4 A E E x x 360 cm lt i 180 cm Technical information Hob dimensions Hob recess dimensions Width 580 mm Width 550 mm Length 500 mm Length 470 mm Heat input Rapid burner 3 0 KW Semi rapid burner 2 0 kW Auxiliary burner 1 0 kW TOTAL POWER Electric supply Gas connection Category Gas supply Appliance class G20 2H 20 mbar 8 kW G30 3 28 30 mbar 567 g h G31 3 37 mbar 557 g h 230 V 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp car tridge fuse R 1 2 112H3 G20 2H 20 mbar 3 By pass diameters ERA i el i Ei i mar SAN Auxiliary Rapid Semi rapid 32 Gas burners for NATURAL GAS G20 20 mbar BURNER NORMAL POWER kW inj 1 100 mm Auxiliary 1 0 70 www zanussi com 13 BURNER NORMAL POWER kW inj 1 100 mm Semi rapid 2 0 96 Rapid 3 0 119 Gas burners for LPG G30 G31 28
15. n is blocked with Make sure that the injector is food residues If there is a fault first try to find a solution to the problem yourself If you cannot find a solution to the problem yourself speak your dealer or the local Service Force Centre If you operated the appliance incorrectly or the installation was not carried out by a registered engineer the visit from the customer service technician or dealer may not take place free of charge even during the warranty period not blocked and the burner crown is clear of food particles These data are necessary to help you quickly and correctly These data are available on the supplied rating plate Model description Product number PNO Serial Number S N Use the original spare parts only They are avail able at Service Force Centre and approved spare parts shops www zanussi com Labels supplied with the accessories bag Stick the adhesive labels as indicated below A B MOD PROD NO SER NO MOD PROD NO SER NO DATA DATA MODEL MODEL x X A Stick it on Guarantee Card and send this part if applicable B Stick it on Guarantee Card and keep this part if applicable Installation A Warning Refer to the Safety chapters Warning The following instructions about installation connection and maintenance must be carried out by qualified personnel in
16. re the flame does not go out when you quickly turn the knob from the maximum to the minimum position www zanussi com Make sure pots are centrally positioned on abrasive products abrasive cleaning pads the rings and do not stick out over edges of solvents or metal objects the cooking surface Disposal Use only the accessories supplied with the a A Warning Risk of injury or suffocation appliance Do not install a flame diffuser on the burner Contact your municipal authority for informa Care and Cleaning i on how to discard the appliance correct y Warning Risk of damage to the Disconnect the appliance from the mains appliance supply Clean regularly the appliance to prevent the Cut off the mains cable and discard it deterioration of the surface material Flat the external gas pipes Do not use water spray and steam to clean the appliance Service Contact the Service to repair the appliance We recommend only the use of original spare Clean the appliance with a moist soft cloth parts Only use neutral detergents Do not use Product description Do not clean the burners in the dishwasher Cooking surface layout Semi rapid burner O 5 2 EJ Semi rapid burner Control knobs Spark generator button a O Auxiliary burner A G Rapid burner Control knobs a P Symbol Description _ smo Description e i no gas supply off posi tion i ignition ma
17. supplied with the appliance If the supply gas pressure is changeable or dif ferent from the necessary pressure you must fit an applicable pressure adjuster on the gas sup ply pipe Adjustment of minimum level To adjust the minimum level of the burners 1 Light the burner 2 Turn the knob on the minimum position 3 Remove the knob www zanussi com 4 With a thin screwdriver adjust the by pass screw position A Sr S A The by pass screw If you change from natural gas G20 20 mbar to liquid gas fully tighten the adjustment screw in If you change from liquid gas to natural gas G20 20 mbar undo the by pass screw ap proximately 1 4 of a turn Warning Make sure the flame does not go out when you quickly turn the knob from the maximum position to the minimum position Electrical connection Do not pull the mains cable to disconnect the appliance Always pull the mains plug The appliance must not be connected with an extension cable an adapter or a multiple socket There is a risk of fire Do not let the power cable to heat up to a temperature of more than 90 C The cable should be guided by means of clamps fixed to the side of the cabinet in order to avoid any contact with the equipment beneath the cooktop Make sure that there is access to the mains plug after the installation Electrical Requirements Permanent electrical installation must agree with the latest 1 E E
18. t cool down before you clean limescale rings water rings fat stains shiny metallic dis colorations Use a special cleaner appli cable for surface of hob 2 Clean the appliance with a damp cloth and some detergent 3 At the end rub the appliance dry with a clean cloth Troubleshooting The stainless steel can become tarnished if it is too much heated Refer to this you must not cook with potstones earthenware pans or cast iron plates Cleaning of the spark plug This feature is obtained through a ceramic igni tion candle with a metal electrode Keep these components well clean to prevent difficult light ing and check that the burner crown holes are not obstructed Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas sup ply pipe and the pressure adjuster if fitted There is no spark when lighting the gas Burner cap and crown are o placed uneven The flame is blow out immediately There is no electrical supply 5 Thermocouple is not heated suf Make sure that the unit is con nected and the electrical supply is switched on Control the fuse If the fuse is released more than one time re fer to a qualified electrician Make sure that the burner cap and crown are in correct posi tions After lightning the flame keep after ignition ficient the knob pushed for equal or less than 10 seconds The gas ring burns unevenly Burner crow
19. ximum gas supply Daily use gna A Warning Refer to the Safety chapters A Warning Remove all the packaging labelling and protective film before first use www zanussi com 5 Ignition of the burner A Warning Be very careful when you use open fire in kitchen environment Manufacturer decline any responsibility in case misuse of the flame Always light the burner before you put cookware To light the burner 1 Push and hold the spark generator button aN 2 At the same time turn the control knob counterclockwise to the maximum position and push it down to light the burner 8 Release the spark generator button when burner lights but keep the control knob on this position for equal or less than 10 sec onds this will let thermocouple to warm up If not the gas supply will be interrupted 4 Adjust the flame after it is regular If after some tries the burner does not light check if the crown and its cap are in cor rect positions 7 Helpful hints and tips A Warning Refer to the Safety chapters Energy savings If possible always put the lids on the pans 6 x wo A Burner cap B Burner crown C Ignition candle D Thermocouple Warning Do not keep the control knob pushed for more than 15 seconds If the burner does not light after 15 seconds release the control knob turn it into off position and try to light the burner again after minimum 1 minute Import
Download Pdf Manuals
Related Search