Da-Lite Tensioned Executive Electrol
Contents
1. INSTRUCTION BOOK FOR Tensioned Executive Electrol DA LITE Important Safety Instructions Pre Installation When using your video equipment basic safety precautions should 1 Carefully unpack screen and remove outer wrapping always be followed including the following from case 1 Read and understand all instructions before using 2 Remove instructions cover and please read 2 Position the cord so that it will not be tripped over pulled or nstructions Fig 1 contact hot surfaces 3 Remove fabric and cardboard strips from access 3 If an extension cord is necessary a cord with a current rating at door Fig 1 least equal to that of the appliance should be used Cords rated 4 Remove access door by gently prying from edge of box for less amperage than the appliance may overheat toward the fabric door 4 To reduce the risk of electric shock do not disassemble this 5 FOR TYPE 3 INSTALLATION ONLY Remove wood strips along appliance Contact an authorized service dealer when repair bottom of screen case work is required Incorrect reassembly can cause electric shock i NOTE Screen surface is not centered in box Screen surface when the appliance is used subsequently f s 25 from motor end 5 The use of an accessory attachment not recommended by f 6 Make sure to recheck measurements of screen location the manufacturer may cause a risk of fire electric2. Solution Screen jammed Will not operate motor hums door open closing mechanism detached from door Closing mechanism detached from door allowing it to jam into box After securing fabric to roller loosen set screws on motor gear and manually rotate solenoid assembly back over top of roller into position then reattach door Match flats on motor drive shaft to gear set screws and tighten Scraping or grinding noise If metal shipping bracket is left attached to screen it may be rubbing on motor end of roller Remove shipping brace Gear noise Gear may need light weight grease Apply light weight grease Incorrect down limit switch setting Lost roller wrap Limit switch out of adjustment See installation instructions See door closure and timing instructions Door closes and screen continues to run upward Door limit out of adjustment Door limit switch is shorted Loosen nut holding limit switch Rotate adjusting position then secure Repair short or replace limit switch LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due t
3. e sure there is approximately 3 16 clearance around access door Keep paint plaster tile or mastic out of hinge Fit access panel so it can be removed for maintenance The picture surface drop and the opening and closing of the fabric door are controlled automatically by limit switches which have been preset at Da Lite When the picture surface is moving upward it is controlled by a limit switch that shuts off when the door closes The height for tensioned screens are adjusted at Da Lite changing the height of screen will change the tension on fabric and cause the screen to hang improperly Do not adjust Tensioned Executive Electrol Installation Suggested Methods of Installation Type 14 2 Offset mounting recessed above ceiling for plaster dry wall or paneling Door painted same finish as ceiling Including Mounting Brackets 9 a X N we Sy IS x EOX SS NE vas SIRIO SOS SHV Ss gt KNX S SRY RAS SOS lt ES x 3 X S x eS x RYN a m SN vi SEN IR ERS SS RS R as aa Ceiling Tile EE gt 3 Approx NOTE Paint the same as doors Block 5 and ceiling or remove and replace with ceiling tile Type 3 Allow min clearance all around surface door Extended mounting recessed above ceiling For use with acoustical or other ceiling tile thick laid over door Sa E
4. lectrical Lenath Of Fabric Width 28 All Sizes L Bracket Mounting Brackets Ae Thick NS SS False Top Type1 amp 2 Allow Ve min clearance all around surface door Flush mounting recessed above ceiling For use with 14 max paneling or installation in existing ceiling using molding around door A f By Se Sa CADA 124 BH AS 2A ARA 9 SS 4A PARA Y Max 2 lt gt 4 34 gt L Bracket Drywall Screw 1 Ya x 1 Screw Y RA ap amp Nut Insert iss AS Mounting 1 GE Brackets ES VA prx YA x A AR SHIM 6 VA O 23 Surface Door J SL le Access Door Ya x 2 Lag Screw Tensioned Executive Electrol Installation 120V Wiring Diagram Qu Down Limit Switch Capacitor Door Solenoid Limit Switch Motor 120V 60 Cycles 1 10 HP Intermittent Duty With Auto Reset Thermal Protector Solenoid Up Limit Switch Operated By Door Internal Wiring Y External Wiring to Be Completed By Installer AA Junction Box Mounted In Screen Case In Which Internal Wiring Terminates In White Black And Red Leads In Multiple Control Installations This Switch ls Replaced By The Low Voltage Control l off Operating Switch Operated From Push Button Stati
5. motor if there is power With power off turn roller by hand to free binding Replace capacitor Secure connection or replace wire Screen starts upward and door closes immediately shutting off motor Fabric door does not fully open Screen runs NOTE Remember door must open by gravity Defective solenoid limit switch Solenoid pin not retracting Defective solenoid Door binding Plaster paint or adhesive can cause the hinge to stick Case may be put into a bind during installation Inadequate clearance around the fabric door on new installations Manually retract pin a few times Check for power to the solenoid terminals If there is power replace solenoid Check blue wire between solenoid switch and solenoid It is either crimped or broken Repair or replace Clean hinge and apply oil Tighten or loosen lag screws located on back of case Provide adequate clearance Clicking noise in each downward revolution Non energized solenoid NOTE There should be three clicks Check for power to solenoid Replace solenoid Loud buzzing noise Solenoid not fully retracting Check for foreign object caught in solenoid Remove object Tighten 4 mounting screws Check for pin binding Door closes on fabric leaving 15 to 20 left hanging out Lost roller wrap See installation instructions Troubleshooting Symptom Cause
6. o improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the even
7. ons Switch Box And 120VAC 60HZ Plate Furnished Side View Of 1 Amp Max With o With Center E A This Switch Cannot Be Used With LVC 240 Volt Wiring Diagram For Standard Wall Switch Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram included in wall switch box included with screen Troubleshooting Visit www da lite com to find installation and troubleshooting tutorials You will also find a link to Live Chat for interactive support and you can contact us by email at info da lite com or by phone at 800 622 3737 or 574 267 8101 with any troubleshooting questions Symptom Cause Solution Screen will not operate or will not go down Blown fuse Tripped circuit breaker Improper wiring to operating switch Improper wiring to junction box in screen NOTE Use low voltage control LVC electrical checklist for either 1 or 3 button control Replace fuse Reset circuit breaker Tighten all loose wire connections Correct any improper connections Check for power Down Position Check for power across black and white leads Up Position Check for power across red and white leads Down Position Check for power at black and white leads Up Position Check for power atred and white leads Shut power off at breaker Remove wall switch and Defective capacitor M
8. otor does not hum Defective wall switch check for broken or loose connection Replace if Defective LVC unit h p defective Check LVC electrical checklist Thermal overload tripped excessive 4 peso Let motor cool down for 15 minutes Try again overheating Disconnect motor leads and check for continuity between black and white wires for down position Burned out motor winding Check for continuity between red and white wires for up position Replace gear motor if either combination shows an open circuit Disconnect down limit switch from circuit Check for Defective limit switch continuity Switches are normally closed and open on contact Replace if defective Temporary fabric binding With power off turn roller by hand to free binding Rotonhanet Shipping bracket not removed Remove shipping bracket and wooden wedge Replace capacitor Troubleshooting Symptom Cause Solution Screen will not move up Motor does not hum Motor hums No power between red and white leads in junction box Check LVC See above Thermal overload tripped acts as a breaker Burned out motor winding Temporary fabric binding Burned out capacitor Broken wire or loose connection in up position red and white leads Check fuse Reset circuit breaker Correct improper wiring Let motor cool for 15 minutes Try again Check for power between red and white motor leads Replace
9. shock or i before installation injury to persons Save These Instructions 7 Remove reverse and remount center support brackets Case Fabric Strip Access Door nn Fabric Door MB Instruction Cover Figure 1 Installation 1 Position screen under mounting location with the case CAUTION Do not secure access door or seal in unit opening down until screen has been secured in position and properly tested for satisfactory operation Do not fit unit so tightl 2 Install screen by raising unit into position between joists at yop E omy that the screen surface drop door binds Door drops by one end only Install one lag screw in each mounting bracket it l ravity only Secure opposite end Support center of the screen using the g y y brackets ATTENTION Ne fixez pas la trappe d acc s ou ne scellez as l unit jusqu ce qu il ait t correctement mis en 3 Level unit lengthwise with a carpenter s level and p a a Sum place et qu il fonctionne convenablement Ne serrez pas l unit au point que la surface de la trappe d acc s de l cran soit bloqu e La trappe tombe uniquement cause de la gravit Installation Continued 4 Bumper Bracket If you are going to cover screen door with paneling or other materials allow access suitable holes or a plug to screws for servicing Use supplied 1 8 nex key and a 7 16 wrench to remove silver shipping brackets attached to slat and screen case Picture s
10. t that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite com www da lite com DL 0266 Rev 2 10 14 O 2014 Milestone AV Technologies LLC Printed in U S A 76359
11. urface should hang freely Fig 2 Remove any tape left hanging on back of fabric Bottom edge should be positioned between bottom edge of case and center of roller Install electrical hook up that applies to your unit Unit should be installed by a qualified electrician Fabric Door Figure 2 Access Door Installation NOTE Must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA C221 and the National Electric Code NEC NFPA 70 Test installation by carefully running picture surface up and down several times Be prepared to stop screen Fabric door must open freely to 90 Make sure picture surface when rolled down has a full wrap around roller No part of roller should be exposed Fabric door and picture surface will drop simultaneously when switch is pressed down Door will close simultaneously with picture surface as picture surface rolls into case Cross Section _ Picture Surface Access Panel Clip Press switch down so that fabric door opens Fig 2 Remove screws 2 located on each bumper bracket NOTE The access door is slotted on one edge permitting the slotted section to fit over the access panel clips on inside of case Place access panel so slot can be pushed over clips Holes in access panel brackets should align with bumper bracket holes Screen Adjustment Replace screws Mak
Download Pdf Manuals
Related Search