Chief PNRUB-G flat panel wall mount
Contents
1. PNR Series Installation Instructions USA International CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002682 Rev00 2014 Milestone AV Technologies www chiefmfg com 11 14 gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 44772. into the cover and top bracket See Figure 4 3 Repeat Steps 1 and for the lower mounting bracket See Figure 4 NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 6 Figure 5 Figure 4 Mounting the Display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 Ibs 18 1kg ALWAYS use two people and proper lifting techniques when installing display 1 Install PSBU interface bracket included with PNRU only to display using hardware and installation instructions included with PSBU bracket 2 Move faceplate to extended position by grasping faceplate and pulling outward away from wall WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in faceplate 3 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figure 5 and See Figure 6 4 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lo
3. 0 to be used with UL Listed Chief accessory PSBU interface bracket not included Model PNRU which includes the UL Listed Chief accessory PSBU interface bracket SAVE THESE INSTRUCTIONS Installation Instructions PNR Series DIMENSIONS 0 TE PSBU INTERFACE BRAC KET NOT SHOWN THE PSBU INTERFACE BRAC KETWILLADD 1 IN DEPTH AND MAY AFFECTTHE LO CATION Mounting Pattern OF THE DISPLAY ON THE MOUNT T 483 19 00 a 8 _ 38 46 _ 25 7 00 Lu 25 1 50 1 81 1 00 1 00 i i C d PA Cer IS o 500 19 69 LA NU 406 16 00 118 DIMENSIONS MILLIMETERS INCHES Installation Instructions PNR Series DIMENSIONS cont d Unit Depth Tilt Adjustment Extended Retra cted Tilted U Tilted Down 15 Roll Adjustment DIMENSIONS MILLIMETERS INCHES Installation Instructions PNR Series LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vas
4. INSTALLATION INSTRUCTIONS Large Flat Panel Dual Arm Wall Mount GS CHIEF PNR Series Our Mounts Your Vision PNR Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief ClickConnect and Centris Select are registered trademarks of Milestone AV Technologies All rights reserved IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result
5. and lateral movement needed to rotate the display The swing arms can be adjusted as follows Adjusting the Swing Arms Off Center With no disassembly required you can adjust the swing arms up to 1 inch to the left of center or up to 1 inch to the right of center Reconfiguring the Swing Arms Left of Center With some disassembly and reassembly required you can move the swing arms to the left of center by reconfiguring the mount Use the first and third slotted holes in the top and bottom mounting brackets Reconfiguring the Swing Arms Right of Center With some disassembly and reassembly you can move the swing arms to the right of center by reconfiguring the mount Use the third and fifth slotted holes in the top and bottom mounting brackets Adjusting the Swing Arms Off Center 1 Remove the display from the mount 2 Loosen four bolts two on the top and two on the bottom securing the swing arm assembly to top and bottom mounting brackets See Figure 11 3 Move the swing arm assembly left or right within slots to desired location Tighten the bolts Install the display on the mount Top bolts Figure 11 Installation Instructions PNR Series Reconfiguring the Swing Arms to Left or Right of 3 Move the swing arm assembly left or right within slots to Center desired location Left of Center See Figure 12 Right of Center See Figure 13 1 Remove the display from the m
6. desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 1 and 2 until desired tension is achieved NOTE If changing from a smaller display to a larger display it may be necessary to increase swing arm tension Figure 15 Sr Tension adjustment screw Figure 14 12 Figure 16 Installation Instructions PNR Series Removing Display from Mount 1 Removeboltor padlock from faceplate if used NOTE The pin may have been used as a more permanent locking device If so remove nut and pin and move from the lower holes to the upper holes 2 Pull back flag on upper mounting hole and press down into Open position See Figure 17 WARNING DISPLAY MAY WEIGH IN EXCESS OF 40 LBS Always use two people and proper lifting techniques when installing or positioning display on mount Remove bolt or padlock if used position move to Open position to remove display 3 4 Carefully lift display from mount Lift up on pin and place flag back against faceplate to return it to Closed position See Figure 18 position move to Closed position after display is removed Figure 17 Figure 18 13 PNR Series Installation Instructions 14 Installation Instructions PNR Series 15
7. ench EEN Installation washer wa H 4 5 1 2 Cable tie 5 16 x 3 1 2 K 1 PSBU bracket Only included with PNRU Installation Instructions PNR Series Installing Mount to Wall WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which the mount is being installed is capable of supporting five times the combined weight of the mount and all attachments NOTE The following instructions assume a suitable mounting structure and surface exists prior to installation CAUTION To avoid personal injury use an assistant when lifting lowering or holding PNR during installation 1 Determine mounting location taking into consideration display size and PNR s range of movement 2 Using a stud sensor locate two wood studs 16 on center See Figure 1 Figure 1 3 Place and level mount against wall aligning mounting holes in upper and lower wall channels with studs See Figure 1 4 Mark four mounting holes making sure mounting holes are located as close as possible to center of studs See Figure 1 5 Drill four 7 32 pilot holes where the mounting holes were marked See Figure 1 10 11 12 Partially install two 5 16 x 3 1 2 lag bolts H into upper pilot holes DO NOT tighten at th
8. in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in Serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this mount does not exceed 200 Ibs 90 7 kg WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors IMPORTANT The PNR Series mounts has been designed to be mounted onto a 2 x 4 51mm x 102 mm 16 on center wood stud wall NOTE The PNR Series includes Accessory Model PNR200
9. is time See Figure 2 Align mounting holes in upper wall channel with lag bolts and hang mount on lag bolts Adjust mount lateral position left until lag bolts are seated in mounting slots in upper wall channel See Figure 2 Place two installation washers G over two lag bolts H See Figure 2 Install two 5 16 x 3 1 2 lag bolts H through mounting holes in lower wall channel and into pilot holes See Figure 2 Place two installation washers G over two lag bolts H See Figure 2 Tighten all hardware DO NOT over tighten du ean x4 in SE Figure 2 Adjusting PNR Height NOTE Height adjustment range up to 1 08 inches 1 Check PNR for the desired height If needed use the adjustment wrench E to adjust the PNR height See Figure 3 Turn adjustment nut clockwise to lower the unit height or e Turn adjustment nut counterclockwise to raise the unit height a 9 DI L Lower Adjustment nut Figure 3 PNR Series Installation Instructions Installing Covers and End Caps NOTE The covers and end caps have pressure fitting ends that lock into place with each other 1 Install cover B over the top bracket See Figure 4 2 Install end caps and D
10. ment knob Vertical tilt lock screw Figure 9 PNR Series Installation Instructions Swivel Tension Adjustment CAUTION DO OVER SWIVEL ADJUSTMENT NUT Over tightening swivel adjustment nut will cause excessive wear and may distort adjustment components 1 Usinga 9 16 wrench not provided slightly tighten or loosen swivel tension adjustment nut See Figure 10 2 Repeat until desired tilt tension is obtained Roll Tension Adjustment 1 If necessary loosen or tighten roll tension adjustment nut See Figure 10 2 Repeat until desired rotational tilt tension is obtained P fe TE Swivel tension adjustment nut 7 d Roll tension adjustment nut Figure 10 10 Swing Arm Adjustments The dual swing arms are shipped installed in the center of the top and bottom mounting brackets which is the standard mounting configuration The top and bottom mounting brackets have slotted holes allowing for lateral adjustment of the dual swing arms After installing top and bottom mounting brackets between two wood studs 16 on center the swing arms can be adjusted or moved off center depending on the location of the mount size of display
11. ount WARNING The next step will release the arm assembly 4 n RR MAU a SE to from the mount The arms and plate may fall if you are not mounting brackets careful Tighten the bolts 2 Remove four bolts two on the top and two on the bottom securing the swing arm assembly to the top and bottom mounting brackets See Figure 12 Install the display on the mount Top bolts Figure 12 Figure 13 11 PNR Series Installation Instructions Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mount s capacity If smaller displays are used it may be difficult to reposition the display after mounting NOTE The display must be mounted prior to adjusting swing arm tension To adjust swing arm tension to compensate for smaller display 1 Place adjustment insert F into tension adjustment screw located at swing arm pivot point See Figure 14 NOTE The display may need to be repositioned in order to gain access to the tension adjustment screw s 2 Usethe adjustment wrench E provided with the mount turn adjustment insert clockwise to increase swing arm tension See Figure 15 or counterclockwise to reduce swing arm tension See Figure 16 NOTE Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension 3 Check swing arm tension If
12. tdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster s y E Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche AO 9 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabega sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale PNR Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION GA vu lt 7 32 5 5mm 2 9 16 B 2 Cover PNR assembly C 2 De End cap x lt E 1 S F 1 E G 4 Adi Adjustment wr
13. wer area of mounting holes and ClickConnect mechanism engages See Figure 5 and See Figure 6 To use as a more permanent lock remove pin and nuts and move to lower holes lt placed through latch holes Figure 6 Installation Instructions PNR Series Cable Management 1 WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure cables do not run through pinch points Thread cable ties J under cable clamps in mount arms See Figure 1 Top view tie Cable clamps Figure 7 Route power audio video cables through the cable channel in top arm See Figure 7 allowing sufficient slack in cables for left right movement of display and swing arm as well as swing arm extension and retraction Secure cables to top arm using two cable ties J Repeat Steps 1 through 3 as necessary for remaining top arm and lower arms WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in faceplate Tension Adjustments Vertical Tilt Tension Adjustment 1 With display mounted check for desired vertical tilt tension 2 Adjust the Centris Select knob until desired vertical tilt tension is obtained See Figure 8 3 To lock the mount at the desired vertical tilt tighten the vertical tilt lock screw See Figure 9 Centris Select adjust
Download Pdf Manuals
Related Search