Ergotron StyleView
Contents
1. 1 Enter default Master PIN 1 2 3 4 5 then press ENTER 2 Press 5 for Master PIN Entry mode 3 Enter new Master PIN and press Enter LEDs will blink green if PIN is accepted 4 Master PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice Master PIN Mode Menu Enter Master PIN and then select one of the below numbers to enter that mode 1 User PIN Entry Mode 2 Pharmacy PIN Entry Change Mode 5 Master Pin Change Mode Programming User PINS 1 Enter Master PIN and press ENTER for Mode Menu 2 Press 1 for User PIN Entry Mode 3 Input new User PIN and press ENTER All LEDs blink green if PIN is accepted You may enter multiple USER PINs consecutively 4 User PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice NOTE User PIN cannot be the same as a Master PIN or Pharmacy PIN Once maximum User PIN storage is exceeded the oldest User PIN will be over written Programming Pharmacy PIN Note System will hold 1 Pharmacy PIN Pharmacy PIN allows all drawers to unlock at the 1 Enter Master PIN and press ENTER for Mode Menu same time Drawers should then be opened at least slightly as the system will auto lock after 2 Press 2 for Pharmacy PIN Entry Mode 10 seconds All LEDs will flash green until system auto locks Once a drawer is opened the 3 Input Pharmacy PIN and press ENTER all LEDs blink green in PIN is accepted corresponding LED for that row will light solid until it is placed2. gt Gems e 3 4 AA 86 mm om oe a gt F o E u 8 5 787 1295 mm 40 216 mm 31 1016 mm 2 5 n 787 mm ea anil 19 75 502 mm 23 43 584 1092 mm 16 75 ene 425 mm O ey 19 25 de i 489 mm 22 38 12 4 2 51mm 4 568 mm 315 mm 21 102 mm 533 mm CPU Compartment n gt Exc q NEN m ME 102 mm E lt 2 3 When figuring dimensions include mounted accessories protruding cables and port replicators or docking stations Side View 4 16 k lt 12 25 lt 1 38 Front View 311 mm I 311 mm AAA AA lt 14 75 375 mmK _ IN LZ A lt 13 58 mm 35 mm lt 12 25 wee 2 75 70 mm gt 330 mm E Top View lt 390 mm 17 5 445 mm lt 17 63 e 2 75 448 mm l i lt 2 75 70 mm lt 21 75 lt 7 75 197 mm 552 mm a a 17 75 lt 4 25 108 mm 451 mm C 888 24 298 G 00 rev A 08 14 Set up 888 24 298 G 00 rev A 08 14 CAUTION Completely release brake engagement before raising or lowering the cart Raising or lowering the cart with the brake partially engaged may cause product damage M3 5 x 6mm 5 16 Sterile Alcohol Prep S CAUTION Close worksurface before opening drawers Open only one drawer at a time Do Not push cart when drawers or worksurface are open Failure to follow these instruct
3. Without Independent LCD Lift 20 Ibs 9 kg 888 24 298 G 00 rev A 08 14 Auto Lock Drawer k k CAUTION Only use NiMh rechargeable batteries Using non Ao OIE Baer yiac 6x rechargeable batteries may cause product damage AA Rechargeable Nickel Metal Hydride USB to computer USB to charge ALD Batteries may not come fully charged and may need to charge for several hours To charge ALD batteries batteries computer needs to be powered on and connected to the USB hub CAUTION Open only one drawer at a time Do Not push cart when drawers are open Failure to follow these instructions may cause the cart to be unstable NOTE User should change Master Personal Identification Number PIN upon receipt of cart Lost Master PIN Contact Ergotron Customer Care for instructions All PINs may vary in length from 4 7 digits Number of PINs possible Carts using StyleLink will store up to 1 000 PINs on the cart Carts not using StyleLink will store up to 100 PINs on the cart Ergotron recommends the following for choosing PIN digit length assumes less than 1 in 25 chance of guessing random User PIN Max number of User PINs gt 50 5 digit length recommended Max number of User PINs gt 300 6 digit length recommended For maximum security use PIN length of 7 Set up Master PIN for the First Time Default Master PIN 12345 Contact Ergotron Customer Care for instructions if Master PIN is lost
4. Storage Area USFF Ultra Small Form Factor Thin Client DO NOT OBSTRUCT AIR VENTS Obstructing air vents may cause overheating and result in equipment damage Center CPU in storage area To increase space and improve airflow power brick may be stored under the storage area If computer with cables is too wide then follow these instructions 10 16 888 24 298 G 00 rev A 08 14 Set up en kK f Adjustment uu It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps Any time CUSTOMER a ADIUST equipment is added or removed from this product resulting in a change in the weight of the mounted load you should repeat these adjustment LIFT TENSION steps to ensure safe and optimum operation EXP ME Adjustments should move smoothly and easily through the full range of motion and stay where you set it If adjustments are difficult and do not stay in the desired position follow the instructions to loosen or tighten the tension to create a smooth easy adjustment motion Depending on your product and the adjustment it may take several turns to notice a difference iuf Release Brake to move riser Lift Up and down C Follow these instructions to tighten or loosen tension NOTE Adjustment may require EM 40 60 revolutions 14mm 9 16 M4 x 8mm b Til
5. or a OT market after 13 August 2005 Range worksurface are open Failure to follow these instructions may cause the cart to be unstable Operational Storage IMPACT HAZARD MOVING PARIS CAN CRUSH AND CUT This Class A digital apparatus complies with Canadian ICES 003 injury or property damage Minimize Lift Tension BEFORE Removing Mounted Equipment Shipping Cart Storing Cart The cart has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC DANGER D IMPACT Rules These limits are designed to provide reasonable protection against harmful interference when the equipment LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy Il existe un risque de blessure corporelle ou d endommagement and if not installed and used in accordance with the instruction manual may cause harmful interference to radio mat riel en cas de non respect de cet avertissement communications Operation of this equipment in a residential area is likely to cause harmful interference in which case Minimisez la tension d l vation AVANT de retirer l quipement fix d exp dier le chariot de stocker le chariot Changes or modifications not expressly approved by Ergotron Inc could void the user s authority to operate the A 2 16 Cet appareil num rique de la classe A est conforme a la norme
6. NMB 003 du Canada FCC Compliance Statement the user will be required to correct the interference at his own expense equipment Please contact Ergotron for complete EMC compatibility information www ergotron com 826 501 IMPORTANT This product will need tension adjustments once installation is complete Make sure all equipment is properly installed on the product before attempting range of motion or tension adjustments Any time equipment is added or changed on this product resulting in a different mounted weight you should repeat the adjustment steps to ensure safe and optimum operation This product should move smoothly and easily through the full range of motion and stay where you set it If movement is difficult or the product does not stay where you set it follow the adjustment instructions to loosen or tighten the tension to create a smooth easy motion Depending on your product and the adjustment it may take many turns to notice a difference Height Adjustable LCD Mount attaches LCDs or tablet PC s with 75x75 or 100x100mm mounting interface Worksurface 2a Worksurface Lock and Release Secure Storage for Laptop Thin Client or CPU Front Handle Height Adjustment Brake Handle USB Hub connects keyboard and mouse USB cables Keyboard tray slides out tilts and allows for right or left mousing with attached mouse holder Keyboard Light under Front Handle Keyboard Light Switch Cable Management and Storage for excess cables a
7. ONS Follow operating instructions 3 Remaining plastics and metals can be recycled through a commercial recycler ON OFF push push NOTE Each position ON OFF is a stable position A cleaning and Maintenance The following procedures are not guaranteed to control infection The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes Ato avoid risk of electric shock do not expose electrical components to water cleaning solutions or other potentially corrosive liquids or substances Ano not immerse Cart or Cart components in liquid or allow liquids to flow into the Cart Wipe all cleaners off surface immediately using a damp cloth Thoroughly dry surface after cleaning Do not use flammable cleaners on Cart surfaces due to close proximity of electrical power and equipment All paints and plastic Cart components will withstand cleaning by most commonly used diluted non abrasive solutions such as quaternary ammonia compounds ammonia enzyme cleaners bleach or alcohol solutions Pen and permanent and dry erase markers can be removed with 91 isopropyl alcohol and a soft cloth e lodine stains can be removed with commonly used cleaners and a soft cloth Never use steel wool or other abrasive materials that will damage the surface finish e Do not use strong solvents such as trichloroethylene and acetone These solvents will damage the surface finish I
8. User Guide ERGOTRON StyleView SV43 Cart with LCD Mount Tools Needed ux D o 14mm 9 16 Components SB AL EA p S 12557 S am ERAS 2 1x UOS Vx Jn Y ud M4 x 8mm Features amp Specifications e eere eere eene ene 2 4 DOU UID H 5 14 Ads MOON siii 11 12 Auto Lock DIA WOR ainia cai 13 14 E QOMOMICS T 14 2X Maint amp Safety MM 15 16 1x D aintenance arety Acemi M4 x 12mm For service and warranty visit www ergotron com For local customer care phone numbers visit http contact ergotron com For the latest User Installation Guide and StyleLink Software Download please visit www ergotron com User s Guide English Gu a del usuario Espanol Manuel de l utilisateur Francais Gebruikersgids Deutsch Benutzerhandbuch Nederlands Guida per l utente Italiano qe www ergotron com Anvandarhandbok svenska USA 1 800 888 8458 0000000 000 N Europe 31 0 33 45 45 600 0000 00g China 86 769 86018920 888 24 298 G 00 rev A 08 14 1 16 Features amp Specifications Failure to heed this warning may result in serious personal 14mm 9 16 Em Temperature Range Temperature Range Relative Relative CAUTION Close worksurface before opening drawers Open M eme mt ipi Humidity only one drawer at a time Do Not push cart when drawers
9. an soit fix Dans un tel cas le pivot d cran se rel verait rapidement et cela pourrait engendrer des blessures www ergotron com 826 502 888 24 298 G 00 rev A 08 14 7 16 Set up 6 To increase space and improve airflow power brick may be stored under the storage area 2x O M4 x 12mm WARNING DO NOT OPERATE WITHOUT GUARD IN PLACE Only remove guard when routing a cable with a large connector through AWARNING the bottom of the compartment Replace guard imediately after DO NOT OPERATE WITHOUT routing cable Failure to replace guard my result in equipment Se GUARD damage and or personal injury IN PLACE 822 447 00 8 16 888 24 298 G 00 rev A 08 14 Set up 7 Place computer and AC power adaptors in compartment Do not place power bricks near computer or compartment air vents M4 x 10mm C Plug the following factory connected cables into your computer USB This cable runs from the USB Hub to your computer and uses your computer to power the USB Hub Keyboard Lights and Fan NOTE Your computer must be turned on for the USB Hub Keyboard Lights and Fan to function WARNING Fan must always be running when computer is on Operating computer without fan may lead to overheating resulting in reduced equipment performance 888 24 298 G 00 rev A 08 14 9 16 Placement of CPU s in Secure
10. back into its original location 4 Pharmacy PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice 888 24 298 G 00 rev A 08 14 13 16 Auto Lock Drawer Unlock Drawer 2 methods NOTE All Drawers in row must be closed before a new row can be unlocked Enter User PIN only numbers for available drawer rows flash green then press desired drawer row number e Key turn clockwise 1 4 turn Drawer Row Numbers Lock Drawer e Wait 4 seconds for lock to engage automatically NOTE Always ensure drawer is pushed in all the way and engaged with lock Drawer Troubleshooting LEDs Alarm Meaning No LEDs on keypad when pressing any number 1 2 3 4 or 5 LED ON green Corresponding Drawer is open Verify battery box is connected to controller 1 2 3 4 or 5 LED flashing red and alarm sounding Corresponding Drawer is open longer than 20 e Verify keypad cable is connected to controller seconds Mute alarm by pressing flashing button corresponding to open drawer e Verify battery box switch is in the ON position and that batteries are All available drawer numbers flashing green Waiting for drawer selection see Unlock Drawer properly installed All LEDs flashing green Pharmacy mode all drawers are unlocked e Drawer selection not available when User PIN is entered All LEDs blink red twice PIN entry rejected exit current mode after 5 seconds timeout e Check to make sure drawer cable is installed securely All LEDs b
11. ents 888 24 298 G 00 rev A 08 14 15 16 Maintenance amp Safety Safety Alerts Associated with this Product The following Warnings Cautions appear in this reference guide or on the cart NOTE Failure to adhere to these guidelines may result in equipment damage or personal injury AN caution The lift brake helps stablilize the worksurface and keyboard tray during normal use but it DOES NOT increase load capacity DO NOT load riser with equipment totaling more than the maximum weight capacity specified by Ergotron Ensure optimum lift function by testing and if necessary re adjusting tension whenever the weight mounted to the riser changes i e equipment is removed or added See Set Riser Lift Tension adjustment instructions A caution Do not operate StyleView Cart with missing or damaged components Do not remove modify or substitute Cart components without consulting Ergotron If you encounter problems with Cart installation or operation contact Ergotron Customer Care CAUTION DO NOT overtighten fasteners Overtightening may cause damage to your equipment A warnine Stored Energy Hazard The worksurface lift mechanism is under tension and will move up rapidly on its own as soon as attached equipment is removed For this reason DO NOT remove equipment unless the worksurface has been moved to the highest position on the tower Failure to follow this instruction may result in serious personal injury and or equipment damage When Ship
12. ions may cause the cart to be unstable A Pa e 6 16 888 24 298 G 00 rev A 08 14 Set up E S cS os SS SSS SSS SSS TL IIT LL qe See gt a Connect Keyboard and Mouse to USB Hub QO a USB Type A USB Type A NOTE Bar Code Scanner should be connected directly to AN computer USB port DO NOT connect Bar Code Scanner to the USB Hub EM Pite n C i jl Wm M4 x 10mm Impact Hazard Moving Parts can Crush and Cut Raise monitor to top of vertical adjustment BEFORE removing Failure to heed this warning may result in serious personal injury or property damage 822 310 2 orawers For 9 drawer carts only After installing the monitor remove and save the shipping screw IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT Failure to heed this warning may result in serious personal injury or property damage Raise monitor to top of vertical adjustment BEFORE removing DO NOT remove Stop Screw without monitor attached Doing so will cause monitor pivot to shoot up rapidly and may cause personal injury DANGER D IMPACT LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER Il existe un risque de blessure corporelle ou d endommagement mat riel en cas de non respect de cet avertissement Elevez l cran au plus haut de l ajustement vertical AVANT de le retirer NE retirez PAS la vis d arr t avant que l cr
13. link green 3 times PIN entry accepted e Remove power from drawer system for 10 seconds and re apply All LEDs flashing red Firmware update in progress LEDs flash red green after User PIN in entered All LEDs flashing red green System power ON or low battery condition Battery charge is low check to make sure USB charging cable is plugged into computer and computer is ON Set up Keyboard Light 1 Turn Computer on 2 Test Keyboard Light Keyboard Light will automatically turn off after 15 minutes if not manually turned off Ergonomics Working Moving customize to your size stow before you go 1 During normal movement release brake and lower worksurface to lowest position for optimal stability and unobstructed view 1 Set top of monitor screen about one inch below eye level Release brake and lift or lower riser as needed 2 Tuck away open trays and return mouse scanner and other accessories to their places 2 Tilt screen for comfortable viewing and to reduce eye and neck strain 3 Pull keyboard tray forward and position mouse tray on right or left as needed 3 Unlock both front casters 4 Work with elbows bent at about 90 to minimize muscle strain 4 Push cart from rear with elbows bent at about 90 to maximize control 5 If the riser moves up and down with difficulty or if it drifts out of set position consult the product and minimize muscle strain manual for adjustment information 5 Don t run out Bef
14. nd power supplies Storage Basket and Rear Handle Front Locking Casters Quick Reference Card Scanner Holder Antimicrobial worksurface and antimicrobial coating on wrist rest Auto Lock Drawer see page 3 for drawer configurations 888 24 298 G 00 rev A 08 14 Features amp Specifications Part Number Auto Lock Drawer SV43 1310 0 SV43 1320 0 SV43 1340 0 SV43 1360 0 SV43 1390 0 Auto Lock Drawer 10 5 267 mm 315 mm Weight Capacity With Independent LCD Lift Without Independent LCD Lift 14 lbs 6 4 kg 20 Ibs 9 kg See How To Eliminate Independent LCD Lift section 0 Ibs 0 kg Open Worksurface lt 5 lbs 2 3 kg Closed Worksurface lt 13 Ibs 5 9 kg CPU Compartment Y 5 oz mm 5 20 508 mm 12 lt 2 Ibs 0 9 kg A see inset bipes Combined LCD and CPU Compartment weight 27 lbs 12 2 kg N CAUTION If the combined LCD and CPU weight is greater than 27 lbs 12 2 kg then the CPU must be mounted to the rear of the cart using the Universal CPU Holder accessory ordered separately Total weight capacity per drawer 2 lbs 1 kg E 0 25 Ibs 0 1 kg Total weight capacity per drawer 888 24 298 G 00 rev A 08 14 3 16 Features amp Specifications 14 63 372 mm e 19 5 Jo T9 495 mm al Mos 178 305 mm ON V 50 5
15. or wear pinching bad Monthly nier cables connectors Inspect for dust at intake vacuum Fan on side of CPU as required using a vacuum cleaner Monthly Avy set compartment that DOES NOT generate ESD Electrostatic Discharge Casters Inspect for wear and debris Monthly Any user Inspect to ensure that maximum Maximum Load recommended loads are not Daily Any user exceeded 1 Please dispose of all batteries in accordance with local law 2 Always replace with similar size battery 33 A h to replace 33 A h and always replace in pairs Americas Sales and Corporate Headquarters EMEA Sales 1181 Trapp Rd Amersfoort The Netherlands St Paul MN USA 31 33 45 45 600 800 888 8458 www ergotron com E econ gt 2014 Ergotron Inc 1 651 681 7600 info eu ergotron com ERGOTRON All rights reserved www ergotron com While Ergotron Inc makes every effort to provide accurate and complete information on the installation sales ergotron com and use of its products it will not be held liable for any editorial errors or omissions including those made in the process of translation from English to another language or for incidental special or consequential damages of any nature resulting from furnishing this instruction and performance of APAC Sales Worldwide OEM Sales equipment in connection with this instruction Ergotron Inc reserves the right to make changes in the product design and or product documentation without notification to its u
16. ore moving make sure cord is unplugged from outlet and hooked to basket for safe travel Remember charge battery fully 10096 every day 6 Stay in charge Powered carts should be plugged into outlet as often as possible to keep battery charged and computer running 1 R 25 IR 14 16 888 24 298 G 00 rev A 08 14 Maintenance amp Safety Signal Word Hazard Symbols Review Level of Hazard The Meaning of Symbols appearing in this Guide on the Cart or on the Power System Indicates an imminently hazardous situation which if not These symbols alert you to a safety condition that avoided will result in death or serious injury demands your attention You should be able to recognize and understand the significance of the following Safety Hazards if you encounter them on the Cart or within Cart documentation such as this Set up Guide Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Used without the safety alert symbol indicates a potentially CAUTION hazardous situation which if not avoided may result in i property damage EQUIPMENT amp ACCESSORIES DISPOSAL INSTRUCTIONS Follow operating instructions 1 Please dispose of all batteries in accordance with local law 2 All Electronics should be recycled through an electronics recycler lil INSTRUCTI
17. ping the cart set the worksurface lift mechanism to the lowest tension setting CAUTION DO NOT loosen tighten or remove any other nuts or bolts on the riser or top of tower Tampering with nuts or bolts may result in an unstable Cart leading to equipment damage and or personal injury CAUTION Release Lift Brake before moving work surface Moving work surface while Lift Brake is engaged may cause serious damage to Lift Engine A warning In the event that repair of the StyleView Cart is needed contact Ergotron Customer Care immediately Cart repair can only be performed by Ergotron Inc or by an Ergotron authorized agent warning This cart is not intended for use in a flammable anesthetic mixture or oxygen rich environment Configuration amp Safety Additional multiple socket outlet or extension cord shall not be connected to the medical system When used in a Medical Electrical system connect only equipment that complies with IEC ISO UL ANSI or CSA standards that are relevant to that equipment A Risk of shock or personal injury when connecting non medical equipment supplied as part of a system directly to the wall outlet when non medical equipment is intended to be supplied by the multiple socket outlet Risk of shock or personal injury when connecting any equipment that has not been supplied as part of the medical system to the multiple socket outlet Recommended Periodic Inspection and Maintenance UI Ethernet USB Inspect f
18. sers For the most current product information or to know if this document is available in languages other than those herein Tokyo Japan www ergotron com please contact Ergotron No part of this publication may be reproduced stored in a retrieval system or www ergotron com info cem ergotron com transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written consent of Ergotron Inc 1181 Trapp Road Eagan Minnesota 55121 USA apaccustomerservice ergotron com Patents Pending and Patented U S amp Foreign Ergotron is a registered trademark of Ergotron Inc 16 16 888 24 298 G 00 rev A 08 14
19. t Forward and Backward Q Loosen knob tilt Display to desired position then retighten knob 888 24 298 G 00 rev A 08 14 11 16 Adjustment C Lift Up and down o To Stop Independent LCD Lift For heavier Displays or when using a Tablet PC you can keep the LCD Lift from moving out of position by installing this screw into one of the three holes on the back of the riser depending on the desired height 1x Q M4 x 8mm IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT Failure to heed this warning may result in serious personal injury or property damage Raise monitor to top of vertical adjustment BEFORE removing DO NOT remove Stop Screw without monitor attached Doing so will cause monitor pivot to shoot up rapidly and may cause personal injury DANGER D IMPACT LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER Il existe un risque de blessure corporelle ou d endommagement mat riel en cas de non respect de cet avertissement Elevez l cran au plus haut de l ajustement vertical AVANT de le retirer NE retirez PAS la vis d arr t avant que l cran soit fix Dans un tel cas le pivot d cran se rel verait rapidement et cela pourrait engendrer des blessures www ergotron com 12 16 826 502 Q Follow these instructions to tighten or loosen tension 3 L Q Follow these instructions to tighten or loosen tension With Independent LCD Lift lt 14 Ibs 6 4 kg A A v
20. t is recommended that any cleaning solution be tested on a small inconspicuous area to ensure surface is not harmed A saustment Service Replacement DO NOT attempt to adjust service or replace any part of the StyleView Cart unless directed to do so through Ergotron approved documentation i e installation instructions Only Ergotron Inc or an Ergotron certified entity may adjust service or replace StyleView Cart components If any component on the Cart is missing or damaged the Cart must not be used contact Ergotron Customer Care immediately to request a replacement part Cables Keep cables neatly organized on the Cart a variety of solutions are provided with your cart for this purpose Excess cables should be routed away from moving components with cable clips Review Cable Routing section of this guide or contact Ergotron Customer Care for more information casters Check casters periodically to make sure they are clean and free of debris that would prevent smooth travel Avoid moving Cart across uneven dirty or damaged surfaces AM customer Equipment Make sure equipment is balanced and mounted securely to Cart Do not reposition Cart components on riser or tower unless instructed to do so in the installation instructions Moving Cart components too high or too low on the Riser may create an unstable condition leading to equipment damage or even personal injury Contact Ergotron Customer Care for information about moving Cart compon
Download Pdf Manuals
Related Search