Chief K1P110B mounting kit
Contents
1. 13 4 Tighten knobs to secure faceplates in position See Figure 13 Figure 13 Array Bar Roll Adjustment 1 Loosen roll adjustment screws on back of array bracket See Figure 14 2 Adjust roll of array bar as desired See Figure 14 3 Tighten roll adjustment screws on back of array bracket See Figure 14 Figure 14 Installation Instructions K1P Series Display Removal WARNING Only remove display from mount when the display can be lifted up from the mount DO NOT remove display unless the display is in the upright position See Figure 15 1 Make sure display is in the upright position 2 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 15 quick release tab Figure 15 Pivot Adjustment Range Single Arm Models 1 Adjust arm angle as desired up to 90 degrees in either direction See Figure 16 WARNING Swinging the arm beyond 90 degrees may result in the mount slipping off the desk causing serious injury top view pivot point of the arm 90 degrees range of motion Figure 16 Dual Arm Models 1 Adjust arm angles as desired within a 90 degree range from the pivot point of the arm and a perpendicular centerline of mount See Figure 17 WARNING Swinging the arm beyond this range may r2. 34 kg 11 34 kg K1P22H 9 lbs 18 lbs 4 08 kg 8 16 kg K1P220 25 Ibs 50 lbs 11 34 kg 22 68 kg SAVE THESE INSTRUCTIONS Installation Instructions K1P Series DIMENSIONS K1P110 POLE CLAMP RANGE II 11 HLASI HORN A h ot th UU LIFT ARN ENG TH RANGE WII HAL A KN Li 1 83 10 21 46 4 nl INTERFACE ROTATION RANGE 01 K1P22H 0 18 19 6 POLE CLAMP RANGE K 1 50 1 90 DYNAMIC LIFT ARM 38 1 50 8 6 75 LENGTH RANGE 171 5 STRAIGHT ARH WAY FULL UPIDO NN amp N 10 21 GO 7 12 j 259 3 180 9 12 32 5 57 312 9 TT 141 5 __ 285 A 1 72 5 _ Oe ES af Do a 3 13 n 79 5 I K1P Series Installation Instructions POLE CLAMP RANGE KOMA 311 508 f Es SCH DYNAMIC LIFT ARM LENGTH RANGE STRRIGHTARN WAX 0 78 W RIC We 1 83 VLLUPIDO WA WI l 19 8 171 5 10 21 46 4 7 12 TILT AA NG E KE NK ne INTER FAC 0 TA TIO RANG Im PAT C 0 NPA TI ILITI 100 100 15115 da DINANIC HEIGHT ADJUSTRANG Hal A 1131 114 1014 2 AN CC ul
3. A DYNAMIC LIFT ARM LENGTH RANGE STRAIGHT ARM MAX FULL UP DOWN MIN xl 10 21 POLE CLAMP RANGE 1 STE my Ditt 259 3 32 5 3803 TILT RANGE 75 1 10200 W4 HEIGATRANG E 25 88 12 88 657 3 ES Installation Instructions K1P Series LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave
4. a punte aperte Steeksleutel Cl a fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a mao A mano Met de hand Ala main Optional Opcional Optional Opcional Opzionale Optie En option C O y x V Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabega sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale o h Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit K1P Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION e 2 3 16 included 1 8 included 5 32 included single display models dual display models B 4 8 C 4 8 D 4 8 M4x14mm M4x25mm M10x5 3x10 e er Y E a F 4 G 4 H 1 2 pole clamp lt 1 4 20 x 1 1 2 1 4 20 x 1 10 24 x 1 4 J 1 included with K1P22H only J3 1 5 32 5 16 18 x 3 L 1 J2 1 J4 1 3 16 Handle Pivot pin J12 1 J5 1 Aen J7 2 J8 2 J9 1 J10 1 J11 1 Pivot Se 1 8 Pocket washer 5 16 18 Array Cable Thin steel Plastic Rotational Cable clip spacer clip washer washer space
5. ARNING Only remove display from mount when the display can be lifted up from the mount DO NOT remove display unless the display is in the upright position See Display Removal section for details K1P Series Installation Instructions For recessed mounting hole installation WARNING Exceeding the weight capacity can result in Place four spacers D on top of mounting holes serious personal injury or damage to equipment It is the on back of display See Figure 5 installer s responsibility to make sure the combined weight of e Using Phillips screwdriver carefully install four all components attached to the K1P Series Monitor Arm up to M4x25mm screws C through corresponding and including the display does not exceed the weight limits holes on faceplate spacers D and into the listed below Use with products heavier than the maximum mounting holes on the display See Figure 5 weight indicated may result in collapse of the mount and its accessories causing possible injury for recessed mounting holes Max Weight Max Weight Allowed for EACH Capacity of y au Display Mounting System quick release faceplate i 5 13 Worx K1P110 25 lbs 25 lbs 11 34 kg 11 34 kg K1P120 25 lbs 25 Ibs 11 34 kg 11 34 kg K1P22H 9 lbs 18 lbs 4 08 kg 8 16 kg K1P220 25 lbs 50 lbs 11 34 kg 22 68 kg 2 Carefully place display face down on protective surface Connect faceplat
6. INSTALLATION INSTRUCTIONS K1P110 K1P120 K1P Pole Mounts G CHIEF K1P Series Our Mounts Your Vision K1P Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is t
7. e to display For flush mounting hole installation Figure 5 e Using Phillips screwdriver carefully install four M4x14mm screws B through corresponding 4 Position display with faceplate attached above mount See holes on faceplate and into the mounting holes on Figure 6 the display See Figure 4 5 Slide faceplate onto mounting head until quick release tab for flush mounting holes clicks into place See Figure 6 quick release faceplate d 3 a y B x4 Figure 4 Figure 6 Installation Instructions K1P Series Handle Installation K1P22 model only 1 Loosen four screws securing handle brackets to K1P22 array See Figure 7 2 Install uprights of handle J2 into handle brackets located on the back of array See Figure 7 J2 Figure 7 3 Position handle J2 at desired height and secure by tightening button head cap screws attaching handle brackets to array See Figure 8 Figure 8 Adjustments Pitch Adjustment non array models 1 Adjust pitch to desired tilt position See Figure 9 2 Adjust pitch tension screw to change the adjustment tension See Figure 9 Pivot Adjustment non array models 3 Adjust pivot position as desired See Figure 9 4 Use 3 16 hex key L to adjust pivot point tension screws to change pivot adjustm
8. ent tension See Figure 9 Rotational tension pivot point tension tension Figure 9 Rotational Adjustment NOTE Optional Rotational adjustment may be locked by installing rotational locking screw H into back of faceplate See Figure 10 Figure 10 5 The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor See Figure 9 6 Use 3 16 hex key L to adjust rotational adjustment screw to adjust rotational tension See Figure 9 K1P Series Installation Instructions Lift Arm Tension Adjustment 1 Use 3 16 hex key L to adjust lift arm tension adjustment screw See Figure 11 K1P110 Reduce tension DO lighter display IN Increase tension Q V heavier display WS Do NOT over tension A adjustment tension K1P120 screw Figure 11 NOTE Tension may also be adjusted with upper tension adjustment screw inside cable management cover and 1 8 hex key M See Figure 12 Reduce tension lighter display Q Increase tension heavier display Do NOT over tension A adjustment tension SS screw Figure 12 10 Adjustments K1P22H models only 1 Loosen knobs securing faceplates to array See Figure 13 2 Slide displays laterally on array to adjust lateral shift See Figure 13 3 Adjust pitch and pivot position as desired See Figure
9. esult in the mount slipping of the desk causing serious injury top view ivot point of the arm 90 degrees range i of motion per arm i perpendicular centerline Figure 17 11 K1P Series Installation Instructions Cable Management 1 Press insides of cable management covers at both ends to unhinge tabs on either end of cable management cover on upper arm See Figure 18 2 Lift cable management cover up until tabs are unhinged and cover is in the open position See Figure 18 Figure 19 3 Route cables through cable management channels See Figure 19 IMPORTANT Be sure to leave enough slack in the cables near display and arm joint to allow for full arm articulation 4 Close cable management covers on monitor arm See Figure 19 5 Repeat Steps 1 4 for lower arm 12 Array Models 1 2 Install array cable clips J7 to back of array See Figure 20 Route cables through array cable clips J7 as desired See Figure 20 Route cables through arm cable clips as desired See Figure 20 Figure 20 Installation Instructions K1P Series 13 K1P Series Installation Instructions 14 Installation Instructions K1P Series 15 K1P Series Installation Instructions USA International G CHIEF Our Mounts Your Vision Europe Chief a products division of Miles
10. he installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located attached to the K1P Series Monitor Arm up to and including the display does not exceed the weight limits listed below Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury Max Weight Max Weight Allowed for EACH Capacity of Display Mounting System K1P110 25 lbs 25 lbs 11 34 kg 11 34 kg K1P120 25 lbs 25 lbs 11
11. r p Installation Instructions K1P Series Assembly And Installation Connecting to Pole 1 Determine approximate location for mount keeping in mind display size extension height adjustment requirements Place mount A against pole with clamp E on opposite side of pole See Figure 1 4 5 Figure 1 Using 5 32 hex key L and appropriate length screws loosely attach assembly to pole clamp E If installing to 1 1 2 NPT pipe use 1 4 20 x 1 1 2 button head cap screws F If installing to 1 1 2 diameter pipe use 1 4 20 x 1 button head cap screws G See Figure 1 Position mount at desired height and orientation Equally tighten screws against mount and the pole clamp Array Installation K1P22H ONLY 1 Slide rotational spacer J10 into opening on array attachment bracket See Figure 2 Use 5 16 18 x 3 button head cap screw J3 two thin steel washers J8 plastic spacer J9 pocket washer J5 pivot pin J4 pivot point spacer J12 and 5 16 18 lock nut J6 to secure array J1 to K1 arm A See Figure 2 NOTE Cable clip J11 can be used in place of pivot point spacer J12 if additional cable managementis desired See Figure 2 Figure 2 Display Installation 1 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 3 Figure 3 W
12. tone AV Technologies Asia Pacific 8800 002479 Rev01 2014 Milestone AV Technologies www chiefmfg com 06 14 pNUb5TNUD TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
Download Pdf Manuals
Related Search