Irox HBR556 weather station
Contents
1. 3 ENG Page 33 48 IROX WEATHER STATION WITH WEATHER FORECAST INDOOR OUTDOOR RADIO THERMO HYGROMETER AND RADIO CONTROLLED CLOCK DCF77 HBR556 INSTRUCTIONS FOR USE 1 INTRODUCTION Congratulations on your purchase of the HBR556 radio weather station The main appliance displays the weather forecast the indoor and outdoor temperature humidity and the time and date The weather data are received by the external sensor The 433 MHz technology used in the appliance means that no cables are needed between the outdoor sensor and the main appliance The appliance is also equipped with a radio clock The time is automatically synchronised with the time signal transmitter DCF77 If the appliance is located out of the range of the DCF77 signal the time and date can also be set manually The appliance has a barometer to reliably calculate the weather forecast As a basic principle the appliance does not need to be operated The respective barometric pressure tendency of the previous 24 hours is depicted graphically 34 IROX TE656NL amp TS33C MANUAL 3 ENG SIZE W93 X H150 mm BY ROSE KOON 08 06 07 ooooo0oo0o0000 O ooooo0oo0o000000 oooo0oo0oo000000 D Ls x a5 36 A LCD DISPLAY For the convenient reading of all values B MODE KEY BACK PANEL Manual setting of clock data 1f required C DOWN KEY v Reduces2. 39 2c PREPARATION OF THE RECEIVER UNIT 1 Open the cover of the battery compartment 2 Insert the 2 batteries 1 5 V UM 3 or size AA in accordance with the respective polarities 3 Close the battery compartment again 2d BATTERY EMPTY DISPLAY When it is time to replace the battery with a new one an indicator will appear next to the display of the indoor temperature batteries receiver unit or outdoor temperature batteries transmitter unit respectively 2e SETTING THE EXTERNAL SENSOR THERMO HYGRO a As soon as the batteries are in the outdoor sensor the sensor starts to transmit the values measured in intervals of approx 45 seconds The main appliance also looks for signals for approx 2 minutes as soon as the batteries are inserted When the signal from the outdoor sensor is received the outdoor temperature and the air humidity values appear on the display b If no sensor signals are received within 2 minutes 77 then appears on the display Press the W key for 3 seconds to initiate a search for the signals of the external sensor In this way you can synchronise the receiving and transmitting signal between the outdoor sensor and the main appliance Important The external sensor must be set to channel 1 40 3 WEATHER FORECAST 3a WEATHER FORECAST Based on the change in barometric pressure the receiver unit calculates the weather development for the next 12
3. 24 hours and indicates this with the following symbols L UL Symbols on P4 y LY y 7 T 4 d HN Ab s rf 26 4544 7 go OG A A at kx ryt f 4 fp EF Je p yt x the display 4 1 1 4 77 3b PLEASE NOTE THE FOLLOWING 1 When the weather station has been put into operation it is not necessary to set the current barometric pressure The appliance will calculate over the next few hours a weather forecast from the changes in barometric pressure 2 Lengthy stable weather conditions make a weather forecast more difficult A change in the weather symbol on the display may at times take longer than desired 3 The weather forecast is calculated solely by means of changes in the barometric pressure 4 The probability of the weather forecast is around 70 and applies for a radius of 20 30 kilometres 5 If the symbol sunny appears at night this means cloudless weather Fog is not displayed by the weather station as this can occur with different weather conditions 6 If you take the weather station with you on your travels the weather forecast will alter due to the differences in height above sea level and the resulting changes in barometric pressure Please wait up to 24 hours until the weather station has calculated the weather forecast based on the barometric pressure conditions at your new location 4 3c BAROMETRIC PRESSURE TENDENCY DISPLAY The indicator for the barometri
4. settings Switch radio signal reception on off New search for the temperature sensor D UP KEY a Increases settings Keep pressed Changes the display Barometric pressure Date barometric pressure 1s not compensated at sea level Changes the display unit for the temperature display in degrees Celsius C or degrees Fahrenheit F E HOLDER FOR WALL HANGING For wall hanging F BATTERY COMPARTMENT For two batteries of the type UM 3 or AA 1 5V alkaline batteries or better are recommended G REMOVABLE STAND For setting the appliance up on a table 37 FEATURES OF THE THERMO HYGRO TRANSMITTER UNIT HTS33 O RESET 5 N je r WA AA o ry ooh enn vw azis A LED DISPLAY Flashes 1 x briefly during signal transmission and 2 x when battery is running out B BATTERY COMPARTMENT For two batteries of the type UM 3 or AA 1 5V alkaline batteries or better are recommended C RESET BUTTON Resetting of the appliance to the default settings and after a change of channel D TRANSMISSION CHANNEL SELECTOR SWITCH Allocates channel 1 channel 2 or channel 3 to a sensor E HOLDER FOR WALL HANGING For wall hanging F C F SWITCH Switching between the temperature display in degrees Celsius C or degrees Fahrenheit F on the display unit 38 2 PUTTING INTO OPERATION 2a PLEASE READ BEFORE USE Please note the following instructions to e
5. transmitter unit 231g without batteries 62g without batteries Dimensions Receiver unit mm External transmitter unit 95 L x 198 H x 33 5 D 55 5 x 101 x 24 mm Resolution temperature gt 0I 0 2 F Transmission frequency 433 MHz Number of channels 3 Range Maximum 30 metres in free field without interference Measurement cycle approx 43 47 secs Measurement range 25 to 95 relative humidity Resolution relative 1 humidity Power supply Receiver unit 2 x UM 3 or AA 1 5V battery External transmission gt 2x UM 3 or unit AA 1 5V battery 45 46 CARE INSTRUCTIONS 1 Protect the appliance against moisture dust knocks and extreme temperatures and only clean it with a dry cloth without using an aggressive solvent 2 Do not intervene in the appliance otherwise the guarantee will expire 3 Please use only new batteries and never mix old and new batteries Please also remember that old batteries should not be disposed of with household waste but should be handed in at the designated collection centres Important With all Irox appliances all disposal fees in Switzerland vRG advance recycling fee and in the EU WEEE have been paid PLEASE NOTE Due to printing restrictions the depiction of the display in these instructions for use may deviate from the actual display Subject to change 47 EC Declaration of Conformity Product TE656 HBR556 When
6. c pressure tendency in the weather forecast window indicates the trend in barometric pressure change in the previous hour Three different indicators are displayed Indicator f 3 Barometric increasing staying falling pressure trend the same Note By default the barometric pressure measured is displayed in mbar hPa The pressure is the pressure measured locally it cannot be set to the sea level Frost alarm The frost alarm symbol appears on the display when the outdoor temperature falls below 3 C This is transmitted by the external sensor on channel 1 When the temperature rises above 6 C the symbol disappears again 42 4 RADIO CLOCK 4a NOTES ABOUT THE RECEPTION OF THE TIME SIGNAL The appliance is designed in such a way that the calendar clock is automatically synchronised as soon as it is within the range of the DCF77 signal To ensure a good reception of the time signal and minimise interference you should not set up the appliance in the vicinity of metallic objects or electrical appliances It normally takes around 3 to 5 minutes until the signal is fully received for the first time depending on the strength of the time signal received The subsequent hourly synchronisation of the time then only takes a few seconds If the reception problems persist please set the clock manually and wait until the next morning The chances of successful reception are greater in the night from
7. midnight to around 4 am One successful reception per week is perfectly sufficient to ensure that the clock runs precisely 43 4b MANUAL SETTINGS The appliance offers various options for changing the default settings To do so press the key MODE for three seconds to enter the setting mode Every time the MODE key is pressed again a flashing function which can be set appears on the display Press one of the keys A or w respectively there You can change the following functions in this sequence in between simply press the MODE key each time Year Calendar Month Day Display Format Day Month or Month Day Time format 24h or 12h Time hours minutes 4c Switching the radio reception off permanently You have the option of switching the radio reception on or off and using the appliance as a normal quartz clock Press the w button for 3 seconds to switch the radio reception on or off When the radio reception is switched off the receiving signal disappears from the display 44 5 TECHNICAL DATA Receiver unit Indoor temperature 5 C to 50 C 23 F to 122 F Relative measurement range 25 to 95 Air humidity at 25 C TPF Resolution temperature gt 0 1 C 0 2 C Resolution relative 1 humidity External transmitter unit Measurement range 10 C to 50 C Outdoor temperature 23 F to 122 F Weights Receiver unit External
8. nsure optimum operation of the appliances Place the receiver unit and the transmitter unit within 1 metre of one another Please follow the sequence described in 2b and 2e and wait until the measured value appears on the display Then install the receiver unit and the external transmitter unit within the possible range of the appliances i e within a maximum radius of 30 metres Please note that the actual range of the transmitters depends on the building materials of the respective building and on the respective position of the external transmitter unit and that the possible distance can be greatly reduced from the 30 metres by external influences various radio transmitters and other sources of interference In such cases we recommend that you seek another position for both the transmitter and the receiver Sometimes moving them by just a few centimetres is sufficient Although the external transmitter units are weatherproof you should not position them in places where they are exposed to direct sunlight rain or snow 2b PREPARATION OF THE EXTERNAL THERMO GYRO TRANSMITTER UNITS 1 Remove the cover of the battery compartment 2 Set channel 1 by moving the sliding switch important only set to channel 1 3 Insert the 2 batteries 1 5 V UM 3 or size AA in accordance with the respective polarities 4 Press the RESET button e g with a paper clip 5 Screw down the cover of the battery compartment again
9. used for its designated purpose this product complies with the basic requirements of Article 3 of R amp TTE 1999 5 EC Directive Efficient use of radio frequency spectrum Article 3 2 of the R amp TTE Directive Applied standard s EN 300 220 1 3 2000 Electromagnetic compatibility Article 3 1 b of the R amp TTE Directive Applied standard s EN 301 489 1 3 2000 Applied standard s EN 300 339 200 Additional information The product is thus compliant with the Low Voltage Directive 73 23 EEC and the Directive Regarding Electromagnetic Compatibility 89 336 EEC and bears the corresponding CE label Compliant in the following countries All EU countries Switzerland and Norway CH and CN QA MANAGER H Y WANG Ww C 0 Hh K S plastic factory Guan Lan Shen Shen Cina 48
Download Pdf Manuals
Related Search