Irox EBR505 weather station
Contents
1. In clock time display mode press MODE ENTER bution to select alarm 1 or 2 then hold and press MODE ENTER again for 2 seconds to access alarm setting 2 The hour digits will flash use V UNIT button to decrease by one hour or A CH button to increase by one hour to your desired hour Hold press either button will change the digit rapidly Press MODE ENTER button to confirm alarm enable automatically when W UNIT button or A CH button pressed 3 The minute digits will flash Use V UNIT button to decrease by one minute or A CH button to increase by one minute to your desired minute Hold press either button will change the digit rapidly Press MODE ENTER button to confirm and finish the setting alarm enable automatically when W UNIT button or A CH button pressed 4 Press amp amp button again in alarm display mode to enable or disable the daily alarm setting automatically save when time out in 10 seconds MOON PHASE Our weather station is equipped with 8 moon phases display i e from new moon to waning crescent on the screen Waring Gb ous Waning Orsoni Wasing Crescent Wong Gbtous PA Moor Last Quarter Sew Mor Pirit Quarter WEATHER FORECAST Our weather station is capable of detecting local barometric pressure changes and based on the data collected predicts the weather forecast for the next 12 to 24 hours at lt a N Qe Fr ON LE N N L S gt N A AI SC Ce Wii We Note 1 The accuracy of a general pressure based w2. ENG IROX EBR505 INSTRUCTION MANUAL FUNCTIONS OF THE WEATHER STATION This weather station measures the environment of its surrounding area and may receive the measured temperature and relative humidity of up to three 868MHz remote thermo hygrometers The information is displayed by LCD 000 oe A S Z e S o Ss Z FEATURES Weather forecast based on barometric pressure changes Radio controlled time DCF77 Displays indoor outdoor minimum and maximum temperature humidity Low battery indication for main unit and wireless sensors Two Daily alarms wake up alarm with SNOOZE function 12 or 24 hour time format Moon Phase LCD Backlight Wall mount or free standing ENG DISPLAY AND FUNCTIONS ON THE MAIN UNIT A B Air pressure trend arrows Indicates the trend of air pressure changes Low battery indicator of outdoor sensor Appears when the batteries of the remote sensor are running dry and the temperature measured by this sensor is no longer reliable The user must change the batteries at once Weather forecast window Shows weather forecast by using icons Moon phase Shows current moon phase Outdoor remote sensor indicator Indicates the current outdoor remote sensor signal received It can display up to 3 different remote sensors which are placed in 3 different places and within 75 meter distance from the main unit Note Many factors may affect the actual distance wall
3. disturbance such as TV computer monitor microwave etc In rooms with concrete or metal walls e g cellar rooms modern office buildings etc the receipt of the signal may be more difficult due to the shielding In such cases find a better location for the device near a window Sometimes it also helps to simply turn the device by 90 thereby improving the alignment of the receiving antenna E i i RLC Mase sort AOL Ractive Once the time signal is received the wave icon will stay on the LCD and time and calendar will automatically be updated Note During the 10 minute time signal reception all manual settings will be suspended If setting is desired press once button key to deactivate the reception You can also press and hold the same key for 3 seconds to manually activate the reception in normal mode Attention The radio controlled time signal reception automatically activates itself again within 24 hours ENG SET THE CLOCK CALENDAR amp LANGUAGE i 2 3 Press amp hold MODE ENTER button for 2 seconds to enter clock setting mode Flashing 12 24 hours will appear Press W UNIT button or A CH button to switch between 24 hours and 12 hours format and then press MODE ENTER button to confirm The hour digits will flash Use the V UNIT button to decrease by one hour or A CH button to increase by one hour to your desired hour Hold press either button will change the digit rapidly Press MODE ENTER button to confir
4. does not press any key for 10 seconds it will exit the channel setting mode and transmit the RF signal The main unit will register the temperature reading For later sensor search and registration Start the sending mode on the main unit by pressing the 4 CH button for 2 seconds On the sensor unit do as described in step 2 and 3 above REMOTE CHANNEL AUTO SCROLLING This device is equipped with an auto scroll function While the auto scroll function is set the unit will automatically cycle to display the temperature and humidity of each remote sensor for 6 seconds 1 To retrieve manually the specific sensor temperature and humidity reading press A CH button until desired channel number is displayed 2 To enable auto scroll function use A CH button to toggle channel 1 2 or 3 until auto scroll icon appears on the left hand side of the second line display DCF 77 RADIO CONTROLLED CLOCK The time signal DCF 77 is transmitted by the atomic clock in Mainflingen near Frankfurt Main The long wave transmitter has a range of up to 1500km If the time icon is displayed without waves you have reception problems Please observe following points There are fewer disturbances in the atmosphere during the night which increases the likeliness of reception One reception per day is completely sufficient to ensure the preciseness of the clock by 1 second Make sure that the device is at least 2 meters 8 feet away from possible sources of
5. e latest manual onto your PC free of charge at www irox com Irox Development Technology www irox com
6. eather forecast is about 70 to 75 and therefore we cannot be held responsible for any inconveniences so caused by an inaccurate one 2 The weather forecast is meant for the next 12 to 24 hours It may not necessarily reflect the current situation 3 The Sunny forecast covering night hours indicates clear weather CE SPECIFICATIONS Main Unit Proposed operating range and measuring range Temperature resolution Displayed OUT temperature range Temperature resolution Indoor Remote relative humidity measurement Displayed relative humidity range Batteries Remote Unit Proposed operating range Displayed relative humidity range Displayed temperature range RF Transmission Frequency Open Field RF Transmission Range Temperature transmission cycle time Batteries ENG 0 0 C to 50 0 C 32 0 F to 122 0 F 0 1 C 0 2 F 10 0 C to 60 0 C 14 0 F to 140 0 F 0 1 C 0 2F 20 RH to 99 RH 3 pieces of AA size 1 5V alkaline battery 10 0 to 50 0 C 14 0 F to 122 0 F 20 RH to 99 RH 10 0 C to 50 0 C 14 0 F to 122 0 F 868 MHz max 75 meters 120 seconds 2 pieces of AA size 1 5V alkaline battery Please also remember that used batteries should not be thrown in the household rubbish bin but handed in at the designated collection points The environment will thank you for it CARE INSTRUCTIONS e Do not expose the device to extreme temperatures or direct sunlight over lon
7. f AA size 1 5V alkaline battery as indicate by the polarity 3 Close the battery door Note Replace the batteries when the low battery indicator appears on the bottom left corner of the LCD BATTERY INSTALLATION FOR REMOTE SENSOR UNIT 1 Remove the battery cover by grabbing its bottom edge near the two recess location from bottom of sensor unit 2 Insert 2 pieces of AA size batteries according to the and polarity marks shown in the battery compartment and then close the battery door with the clip on press down the snap on both sides slightly e e Front view Back view ENG WIRELESS REMOTE SENSOR REGISTRATION PROCEDURE 1 Insert 3 pieces of AA batteries first to the main unit The temperature display shows while the wave icon will keep blinking for 2 minutes indicate the main unit is in sensor searching mode 2 In a second step insert the 2 pieces of AA batteries into the sensor unit The red LED on the front will start flashing at a rate of one time per 2 seconds indicates channel 1 is in use 3 While the red LED is flashing press once the A CH button located in the battery compartment will change the sensor channel setting to 2 Keep toggle on A CH button can change channel setting up to 3 The LCD is blinking at a frequency to indicate the channel setting i e continuous blinks 2 times indicate channel 2 is selected Note If user
8. g mode MAX MIN Button Toggle to view the MAX MIN reading of the indoor and remote temperature humidity Press and hold 2 seconds to clear indoor and current channel remote temperature humidity memories amp Button While in alarm display mode press once to toggle between enable or disable the daily alarm Press and hold 3 seconds to manually activate the radio controlled function and press during reception once to deactivate Note The radio controlled time signal reception automatically activates itself again within 24 hours MODE ENTER Button Toggle amongst display for clock HR MIN SEC clock day HR MIN Weekday alarm 1 alarm 2 calendar Date Month Press and hold 2 seconds to access setting mode of clock or alarm while in corresponding display mode GETTING STARTED This Weather Station was designed for easy set up For best operation the following steps are required to be done in the proper sequence 1 2 3 Insert batteries for main unit before doing so for the sensor units The main unit cannot be programmed manually until the wireless remote sensor unit registration procedure has been completed Position the remote unit and main unit within effective transmission range which in usual circumstance is within 75 meters Although the remote unit is weather resistant it should be placed away from direct sunlight rain or snow ENG BATTERY INSTALLATION FOR MAIN UNIT 1 Remove the battery door 2 Insert 3 pieces o
9. ger periods Avoid blows and shocks of any kind to the device For cleaning use a dry soft cloth that you have moistened with water and a mild cleaning agent Never use volatile substances such as benzene thinner cleansing agents in spray cans etc When the device is not being used store it in a dry area and out of the reach of small children If the device is activated under extreme coldness it may occur that the display becomes illegible As soon as it is returned to a warm environment the device will function normally Please keep the user s manual and other documents delivered with the device stored carefully so that you can reference them at a later point if necessary Please use only new batteries and never mix old and new batteries Please also remember that old batteries should not be disposed of with household waste but should be handed in at the designated collection centres Important With all Irox appliances all disposal fees in Switzerland vRG advance recycling fee and in the EU WEEE have been paid SUPPORT This device is a new development of Irox Development Technology All information was made and checked by means of a functioning instrument It may occur that adjustments and improvements of the device will take place that due to typographical procedures were not able to be listed in this manual Should you notice deviations which make it difficult for you to operate and use the instrument you may at any time download th
10. m The minute digits will flash Use the V UNIT button or 4 CH button to set your desired minute Hold press either button will change the digit rapidly Press MODE ENTER button to confirm Note Every change of minute digit will automatically reset the seconds to zero The year digit will flash and Yr icon appears Press W UNIT button or A CH button to set your desired year Press MODE ENTER button to confirm D and M icons will flash Press V UNIT button or 4 CH button to select D and M Date and Month or M and D Month and Date format Press MODE ENTER button to confirm Month digits will flash Press V UNIT button or 4 CH button to set your desired month Press MODE ENTER button to confirm Do the same to set Date Note The moon phase and the weekday will be automatically calculated and displayed according to the date set as above E digit will flash Press V UNIT button or A CH button to switch 5 languages display of weekday English German French Spanish Italian See table 1 Press MODE ENTER button to confirm and exit setting mode MULTILANGUAGE DAY DISPLAY LANGUAGE m iI wo na a z if Wan Din Be pis AD Owa EUa EUon LU Wos Noe Mas Mou Maw WE Noa MEn Moa MEn Hoo Doo Ew Mos Gh ve nw Fon FRon WE Wor YEr Raw Aou Aou Aau SAn Note If no key press during setting mode for 10 seconds it will automatically keep the setting and exit to normal display ENG TO SET DAILY ALARM 1
11. s metal parts electrical appliances etc Auto scroll indicator The rotating arrow icon is shown to indicate the auto scroll of the 3 different remote channels Outdoor maximum minimum indicator Indicates the maximum minimum outdoor temperature and humidity are displayed Low battery indicator of main unit Shown to indicate the battery in the main unit is low and all displayed information on the LCD is no longer reliable The user needs to change the batteries at once Indoor indicator Indicates the indoor temperature and humidity are displayed Indoor maximum minimum indicator Indicates the maximum minimum indoor temperature and humidity are displayed Clock window Display current time current time and weekday calendar or alarm time Radio reception signal Indicates the condition of DCF77 radio controlled time reception Alarm on icon Appears when alarm is activated ENG DESCRIPTION OF BUTTONS The EBR505 has 6 function buttons on the front 1 2 SNOOZE LIGHT Button Press once to activate the LCD backlight for 5 seconds or SNOOZE function V UNIT Button Press once to decrease the setting in clock calendar or alarm setting mode While in clock display mode press once to toggle between C and F A CH Button Press once to increase the setting in clock calendar or alarm setting mode Select among channel 1 2 3 or to enter auto scroll mode Press and hold 2 seconds to activate or deactivate the sensor searchin
Download Pdf Manuals
Related Search