Baaske Medical Silence TP 2
Contents
1. Limit CPUID Maximum Disabled for Windows XP IDE Configuration ATA or IDE Configuration Select ATA or IDE configuration Configure SATA AS Select a configuration for SATA controller HDD Acoustic Power Ma Option to enable or disable HDD Acoustic Power Management DiPM Option to enable or disable DiPM Intel IGD SWSCI OpRegion DVMT Mode Select Selects DVMT Mode used by Internal Graphics Device DVMT FIXED Memory Selects DVMT FIXED Mode Memory size used by Internal Graphics Device IGD Boot Type Select the Video Device which will be activated during POST This has no effect if external graphics present LCD Panel Type Select LCD panel used by Internal Graphics Device by selecting the appropriate setup item Panel Scaling Select the LCD panel scaling option used by the Internal Graphics Device GMCH BLC Control Back Light Control Setting BIA Control Spread Spectrum clock gt gt Hardware Spread is controlled by chip gt gt Software Spread is controlled by BIOS 22 TV1 Standard TV2 Standard Active LFP Select the Active LFP Configuration No LVDS VBIOS does not enable LVDS INT LVDS VBIOS enables LVDS driver by Integrated encoder SDVO LVDS VBIOS enables LVDS driver by SDVO USB Configuration Legacy USB Support Allows USB devices to be used in MS DOS EHCI Hand off This is a workaround for OSes without EHCI hand off support The EHCI ownership change should be claimed by EHCI driver USB transfer time o2. Maximum Read Request Set Maximum Read Request Size of PCI Express Device or allow System BIOS to select the value ASPM Support Set the ASPM Level Force LO Force all links to LO State AUTO BIOS auto configure DISABLE Disables ASPM Extended Synch If ENABLED allows generation of Extended Synchronization patterns ACPI Settings Enables ACPI Auto Conf Enables or Disables BIOS ACPI Auto Configuration Enable Hibernation Enables or Disables System ability to Hibernate OS S4 Sleep State This option may be not effective with some OS ACPI Sleep State Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed S5 RTC Wake Settings Wake System with Fixed Time Enables or disables system wake on alarm event When enabled the system will wake on the time specified Wake system with Dynamic Time Enables or disables system wake on alarm event When enabled the system will wake on the current time Increase minute s CPU Configuration Hyper Threading Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology and Disabled for other OS OS optimized for Hyper Threading Technology 21 Core Multi Processing Enable or Disable Core Multi Processing mode Execute Disable Bit XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS Windows Server 2003 SP1 Windows XP SP2 SuSE Linux 9 2 RedHat Enterprise 3 Update 3
3. necessary such as reorienting or relocating the e medic Silence TP 2 8 TP 1 Over the freguency range 150 kHz to 80 MHz field strengths should be less than V m b B Safety ISO 7000 0434 CAUTION consult ACCOMPANYING DOCUMENTS ISO 7000 1641 Follow operating instructions or Consult instructions for use IEC 60417 5009 STAND BY S a gt IEC 60417 5031 Direct current EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your display products please follow the guidance of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself jat The mark on electrical and electronic products only applies to the current European Union Member States When networking with electrical devices the operator is responsible for ensuring that the resulting system meets the reguirements set forth by the following standards EN 60601 1 IEC 60601 1 Medical electrical eguipment Part 1 General reguirements for safety EN 60601 1 1 IEC 60601 1 1 Medical electrical eguipment Part 1 1 General requirements for safety Collateral standard Safety requ
4. 4GB 8GB Serial ATA SATA3 x 2 600MB s transfer rate USB x 7 socket USB 2 0 x 4 external x 3 internal COM x 6 x 2 external x 4 internal Audio Realtek ALC262 audio codec 2 2 watts amplifier LAN Marvell 88E8071 Gigabit Ethernet x 2 BIOS AMI BIOS 4M EEPROM RTC wake up Wake on LAN Power on after power failure PnP ACPI Speaker 1 5 watts x 2 front bottom LCD Panel Size 21 5 wide 16 9 Resolution Full HD 1920 x 1080 Brightness 250 nits Contrast 1000 1 Color numbers 16 7M 6 bit x 3 Hi FRC Viewing angle 170 H 160 V Response time 5ms R F Backlight LED 30 000 hours life time Touch Panel Type Front full flat customized touch panel Technology Resistive touch 5 wire Light transmittance gt 78 at 550 nm wavelength Hardness 3H Touch stylus No limitation Resolution 4096 x 4096 10 Life time 35 million activations Storage amp Expansion HDD 2 5 SATA HDD drive bay x 1 anti vibration kit Expansion slot PCI E x16 x 1 optional Card size 100 x 155 x 18 0 5 mm or 68 x 220 x 18 0 5 mm Mini PCle x 2 52 pin card edge type 1 0 amp Control Keys USB USB 2 0 x 4 COM DB 9 x 2 RS232 RS232 422 485 LAN RJ 45 x 2 Gigabit Video out DVI I x 1 Audio Line out Microphone in 3 5 mm phone jack Power input DC in x 1 6V 32V Control keys Front side projected capaci
5. Baa ke JA Medical e medic Silence TP 2 1 All in one Medical Panel PC e medic CCD e ese e nr Table of Contents I Safety amp Regulatory Notice ccccccsssscecssssececsssseesssssseeseessseeees 2 9 A Electronic Magnetic Compatibility i 2 6 Bi SALEM Asemele veli eaka tete A 7 8 C Intend d Use r eii late Alena ela lele eect 9 9 IL Product Basic isa ares cetictesceectdeccetesteccteecesstes 10 18 Ar Specifications xs tente Hee eee 10 12 B The Packing Outline I O Control Buttons 13 15 C Others tia iaia 16 18 I a cieca 19 29 I Safety amp Regulatory Notice A Electronic Magnetic Compatibility Guidance and manufacturer s declaration electromagnetic emissions The e medic Silence TP 2 amp TP 1 are intended for use in the electromagnetic environment specified below The user should assure the products are used in such an environment Compliance Electromagnetic environment guidance RF emissions The e medic Silence TP 2 amp TP 1use RF CISPR 11 energy only for its internal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF emissions The e medic Silence TP 2 amp TP 1 are CISPR 11 suitable for use in all establishments including domestic establishments and those directly connected to the public low voltage power supply network that suppli
6. NumLock state Quiet Boot Allows you to determine whether to display the AMI Logo at system startup Disabled displays normal POST message Fast Boot Enables or disables the quick boot function to speed up the system boot up process to shorten the waiting time for entering the operating system and to deliver greater efficiency for daily use GateA20 Active This option is useful when any RT code is executed above 1MB Upon Request GA20 can be disabled using BIOS services Default 26 Always Do not allow disabling GA20 Option ROM Messages Sets display made for option ROM Interrupt 19 Capture Enables or disables Option ROMs to Trap Int 19 Boot Option Priorities Specifies the sequence of loading the operating system from the installed hard drives 27 Security Aptio Setup Utility Copyright C 2010 American Megatrends Inc Administrator Password Enables or disables the security chip It is recommended that you use this function with the Administrator User password 28 Save amp Exit Aptio Setup Utility Copyright Built in EFI Shell Save Changes and Exit Exit system setup after saving the changes Discard Changes and Exit Exit system setup without saving any changes Save Changes and Reset Reset the system after saving the changes Discard Changes and Reset Reset system setup without saving the changes Save Changes Save the changes done so far to any of setup
7. ansportation 186 1 060 hPa Vibration Operating 15g 0 53 oz 11 ms half sine wave Non operating 50g 1 76 oz 11 ms half sine wave Operating 5 17 Hz Shock Amplitude 0 117 500Hz Acceleration 1 0G Non operating 10 55Hz 0 15g 55 500Hz 2 0g Regulatory CE Medical Safety 60601 1 3 edition EN 60601 1 2006 Medical EMC 60601 1 2 2007 Options Options WLAN mini PCIe module w internal antenna x 2 Bluetooth 2 1 USB Battery pack Power adaptor w 2 4m or 3 6m DC cable Desktop stand 12 B The Packing Outline 1 0 Control Buttons Basic packing list The medical PC e medic Silence TP 2 fanless or TP 1 smart fan Power adaptor Sinpro MPU101 105 AC power cord Touch stylus pen DVD title with drivers amp user s manual Screws for rear cover VESA mounting Note The contents may vary due to different options or configuration Outline dimension e medic Silence TP 1 r rrenad k 13 e medic Silence TP 2 The I O interface basic configuration LAN x2 RS232 422 485 RS232 USB x4 6 DVI I Reset DC in PCI E PCI expansion Line out Micropone in 14 The control buttons amp LED indicators N O CON DM BW PA Control buttons amp LED indicators HDD indicator Dark non operating stand by Amber blinking accessing Batt
8. ction from structures objects and people Guidance and manufacturer s declaration electromagnetic immunity The e medic Silence TP 2 amp TP 1 are intended for use in the electromagnetic environment specified below The user of the e medic Silence TP 2 amp TP 1 should assure that it is used in such an environment Immunity test IEC 60601 Compliance Electromagnetic test level level environment guidance 26 kV contact A6 kv contact Floors should be wood discharge ESD IEC 61000 4 2 Electrical fast transient burst IEC 61000 4 4 Surge IEC 61000 4 5 interruptions and voltage variations on power supply input lines IEC 61000 4 11 8 KV air 2 kV for power supply lines 1 KV for input output lines 1 KV line s to line s 2 kV line s to earth lt 5 UT gt 95 dip in UT for 0 5 cycle 40 UT 60 dip in UT for 5 cycles 70 UT 30 dip in UT for 25 cycles lt 5 UT gt 95 dip in UT for 5 sec 8 kV air 2 kV for power supply lines 1 kV for input output lines 1 kV line s to line s 2 kV line s to earth lt 5 UT gt 95 dip in UT for 0 5 cycle 40 UT 60 dip in UT for 5 cycles 70 UT 30 dip in UT for 25 cycles lt 5 UT gt 95 dip in UT for 5 sec concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Ma
9. ery indicator Dark non operating Amber operating Amber blinking battery low Power indicator Dark off Green on Power on off button Speaker volume adjustment button Speaker volume adjustment button LCD brightness button LCD brightness button LCD backlight on off button amp indicator Dark backlight on Green backlight off 10 Touch enable disable button amp indicator Dark touch enabled Amber touch disabled a Press the button for 5 seconds to disable or enable touch b When the touch is disabled after 60 seconds the touch will be enabled automatically C Others To clean or disinfect the system To clean or disinfect the system to avoid any damage to the touch panel and the plastic housing please check below chemical resistance table to ensure you disinfectant does not contain harmful ingredients We suggest to use Ethanol and do check with the personal who is responsible for disinfecting Chemical Touch panel 10 Sodium Hydroxid OK Acetone OK Carbitol Acetate OK Cellosolve Acetate OK Ethanol Alcohol OK Methylene Chloride OK Hydrochloric Acid 6 OK Nitric Acid 40 Damage Hexane OK Isopropanol Isopropyl Alcohol Propanol OK Methyl Ethyl Ketone OK OK Bleach Sodium Hypochlorite NaOCl Benzyl alcohol Hydrogen peroxide Chemical Plastic housing 40 S
10. es buildings used for domestic Voltage purposes fluctuations Harmonic emissions IEC 61000 3 2 flicker emissions IEC 61000 3 3 Recommended separation distances between portable and mobile RF communications equipment and the e medic Silence TP2 amp TP1 The e medic Silence TP 2 amp TP 1are intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The user of the e medic Silence TP 2 amp TP 1 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the e medic Silence TP 2 8 TP 1 as recommended below according to the maximum output power of the communications equipment Rated maximum output Separation distance according to frequency of power of transmitter transmitter 150 kHz to 80 80 MHz to 800 MHz to MHz 800 MHz 2 5 GHz d 1 2 F d 1 2 F d 2 3 JF For transmitters rated at a maximum output power not listed above the recommended separation distanced in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer NOTE 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and refle
11. he battery will be enabled automatically 18 III BIOS Immediately after powering on the system during the POST Power On Self Test stage press the lt Del gt key to enter the BIOS setup utility program Follow the menu amp the keys instruction to modify the BIOS configuration amp settings Main Aptio Setup Utility Copy vip 301 ri gt 2011 American Megatrends Inc an System Date 19 Advanced Copyright gt PCI Subsystem Settings Launch OpROM Support Launch PXE OpROM Enables or disables Boot Option for Legacy Network Devices Launch Storage OpROM Enables or disables Boot Option for Legacy Mass Storage Devices with Option ROM PCI Subsystem Settings PCI ROM Priority In Case of multiple Option ROMs Legacy and EFI Compatible specifies what PCI Option ROM to launch PCI Latency Timer Value to be programmed into PCI Latency Timer Register VGA Palette Snoop Enables or disables VGA Palette Registers Snooping PERR Generation Enables or Disables PCI Device to Generate PERR SERR Generation Enables or Disables PCI Device to Generate SERR Relaxed Ordering Enables or Disables PCI Express Device Relaxed Ordering 20 Extended Tag If ENABLED allows Device to use 8 bit Tag field as a requester No Snoop Enables or Disables PCI Express Device No Snoop option Maximum Payload Set Maximum Payload of PCI Express Device or allow System BIOS to select the value
12. ins power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment If the user of the e medic Silence TP 2 amp TP 1 require continued operation during power mains interruptions it is recommended that the e medic Silence TP 2 amp TP 1 be powered from an uninterruptible power supply or a battery Power 3A m frequency 50 60 Hz magnetic field IEC 61000 4 8 3 A m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment NOTE UT is the a c mains voltage prior to application of the test level Guidance and manufacturer s declaration electromagnetic immunity The e medic Silence TP 2 amp TP 1 are intended for use in the electromagnetic environment specified below The user of the e medic Silence TP 2 amp TP 1 should assure that it is used in such an environment Immunity Conducted RF IEC 61000 4 6 Radiated RF IEC 61000 4 3 Compliance level Electromagnetic environment guidance Portable and mobile RF communications equipment should be used no closer to any part of the e medic Silence TP 2 amp TP 1 including cables than the recommended separation distance calculated from the equation applicable to the f
13. irements for Medical electrical systems EN 60601 1 2 IEC 60601 1 2 Medical electrical equipment Part 1 2 General requirements for safety Collateral standard Electromagnetic compatibility Requirements and tests Accessory equipment connected to the analog and digital interfaces must be in compliance with the respective nationally harmonized IEC standards i e IEC 60950 for data processing equipment IEC 60065 for video equipment IEC 61010 1 for laboratory equipment and IEC 60601 1 for medical equipment Furthermore all configurations shall comply with the system standard IEC 60601 1 1 Everybody who connects additional equipment to the signal input part or signal output part configures a medical system and is therefore responsible that the system complies with the requirements of the system standard IEC 60601 1 1 The unit is for exclusive interconnection with IEC 60601 1 certified equipment in the patient environment and IEC 60XXX certified equipment outside of the patient environment If in doubt consult the technical services department or your local representative C Intended Use The e medic Silence TP 2 amp TP 1 are designed to serve as a medical PC for general purpose usage in the hospital environment and for clinic review purpose It could be used as a computer device for Surgical Radiology PACS Picture Archiving Communication Systems LIS Lab Information Systems and Electronic Medical Record application I
14. odium Hydroxid Damage Acetone Damage Carbitol Acetate Damage Cellosolve Acetate Damage Ethanol Alcohol 500g load with 95 Alcohol gt OK Methylene Chloride Damage Hydrochloric Acid 6 Damage Hexane Damage Isopropanol Isopropyl Alcohol Propanol Damage Methyl Ethyl Ketone Damage Damage 500g load with 5 Cresol gt OK Damage Damage Bleach Sodium Hypochlorite gt NaOCl 500g load with 10 Bleach gt OK Benzyl alcohol Damage Hydrogen peroxide Damage The internal battery optional For those systems installed with internal battery below is the specification Battery cell type Lithium lon rechargeable battery cell 2000mAh cell Configuration 2S2P Typical capacity 4000mAh for two cells Minimum capacity 3800mAh for two cells Nominal voltage 7 3 V average Energy 29 2 Wh typical 27 74 Wh minimum Charge voltage 8 4 V typical Charge time System on 1A 200 minutes System off 2A 120 minutes Battery life Discharge gt 10 minutes for 300 times lt 70 capacity left During the transportation we suggest you to disable battery Power off the system Disconnect the DC power or AC power cord Press the speaker volume button for 10 seconds Next time when you connect the AC power and power on the system t
15. options Discard Changes Discard the changes done so far to any of setup options Restore Defaults Restore load default values for all the setup options Save as User Defaults Save the changes done so far as User Defaults Restore User Defaults Restore the User Defaults to all the setup options EFIGUI_FLASH Press lt Enter gt to execute the simple EFI GUI Flash Program 29 Baa ke D LS Baaske Medical GmbH amp Co KG Bacmeisterstr 3 32312 L bbecke Tel 49 5741 236027 0 Fax 49 5741 236027 99 vertrieb baaske net www baaske medical de
16. requency of the transmitter Recommended separation distance d 1 2 P d 1 2 80 MHz to 800 MHz d 2 3 P 800 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol 6 NOTE 1 At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the e medic Silence TP 2 8 TP 1are used exceeds the applicable RF compliance level above the e medic Silence TP 2 8 TP 1 should be observed to verify normal operation If abnormal performance is observed additional measures may be
17. t shall not be used in life supporting systems WARMING Critical diagnostic decision must not be based solely on images displayed by this device CAUTION Use suitable mounting apparatus to avoid risk of injury The user is not to touch SIP SOPs and the patient at the same time The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70dB A a Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked Hospital Only or Hospital Grade b Use a power cord that matches the voltage of the power outlet which has been approved and complies with the safety standard of your particular country c CAUTION This power adapter Sinpro MPU101 105 is a forming part of this medical PC CAUTION Do not leave this equipment in an uncontrolled environment where the storage temperature is below 20 C 4 F or above 60 C 140 F This may damage the equipment II Product Basic A Specifications Main System CPU for TP 2 Support Intel Core i Ivy Bridge ultra low power CPU w BGA1023 package 17W TDP max and integrated graphics CPU for TP 1 Support Intel Core i Ivy Bridge mobile CPU w PGA988 package 35W TDP max and integrated graphics Chipset Intel BD82HM65 PCH Graphics Intel HD Graphics HD 4000 Memory 8GB maximum x 2 DDR3 SODIMM 1066 1333 1600MHz 2GB
18. tive type Power on off Brightness Audio volume Backlight on off Touch on off Power Power adaptor External 100 watts 90 264V AC in 12V DC out medical grade Sinpro MPU101 105 Power consumption TP 2 65 watts typical without any add ons TP 1 75 watts typical without any add ons Internal battery optional Rechargeable Lithium lon 2S2P 29 2Wh avg 27 74Wh min for 20 25 minutes operating approx Charge time 2 hours system off 3 5 hours system on Mechanical amp Environmental Housing Front Full flat design Touch standard Glass optional Rear Plastic I O cover w antibacterial treatment Color Housing White Control key icons Grey IP rating IP65 front side Cooling TP 2 fanless TP 1 Variable speed smart fan design lt 30 dB typical Mounting VESA 75 x 75 100 x 100 mm Kensington lock Yes x 1 at bottom Dimension 540 x 375 x 78 mm W x H x D w o stand Weight net 7 Kg approximate w o power adaptor Temperature Operating 0 C to 40 C 32 F 104 F Storage Transportation 20 C to 60 C 4 F 140 F Humidity Operating 10 to 90 non condensing Storage Transportation 10 to 90 40 C non condensing 11 Operating up to 3 000 m 9 842 feet Altitug s Shipping up to 12 192 m 40 000 feet HE Operating 700 1060 hPa Storage Tr
19. ut The time out value for Control Bulk and Interrupt transfers Device reset time out USB mass storage device Start Unit command time out Device power up delay Maximum time the device will take before it properly reports itself to the HOST Controller Auto uses default value for a Root port it is 100 ms for a Hub port the delay is taken from Hub descriptor F71869 Super IO Configuration Serial Port 0 Configuration Set Parameters of Serial Port 0 COM A Serial Port 1 Configuration Set Parameters of Serial Port 1 COM B F71869 H W Monitor Monitor hardware status Second Super 10 Configuration Serial Port 1 Configuration Set Parameters of Serial Port 1 COM C Serial Port 2 Configuration Set Parameters of Serial Port 2 COM D 23 Serial Port 3 Configuration Set Parameters of Serial Port 3 COM E Serial Port 4 Configuration Set Parameters of Serial Port 4 COM F Serial Port Console Redirection Serial Port Console Redirection 24 Chipset Aptio Setup Utility Copyright C 10 American Megatrends Host Bridge Host Bridge South Bridge This screen provides information on Host Bridge South Bridge parameters 25 Boot Aptio Setup Utility Copyright C 2011 American Me Boot Option 1 B802 DOO Yukon Boot Setup Prompt Timeout Number of seconds to wait for setup activation key 65535 0xFFFF means indefinite waiting Bootup Numlock State Selects the keyboard
Download Pdf Manuals
Related Search