Humanscale QuickStand
Contents
1. Adjusting Weight Capacity WARNING Do not use a Power Drill to adjust the tension adjuster gt Tools 6 mm Hex Key e Remove top cover from QuickStand unit to expose the tension adjuster screw fig R e Slowly begin to turn the tension adjuster screw clockwise to increase the tension fig S e Werecommend turning the tension adjuster screw 10 revolutions at a time before checking to see if your QuickStand is correctly balanced e Once you have adjusted your QuickStand try raising and lowering a few times until it fluidly adjusts Your QuickStand should stay where you set it e Ifyou need to make further adjustments please follow these steps again Increase Weight Capacity If the platform is too heavy to raise but easy to lower and does not stay in place when raised please adjust the tension adjuster Decrease Weight Capacity If the platform is too easy to raise but difficult to lower and does not stay in place when lowered please adjust the tension adjuster STEP 14 Adjusting Monitor Height SINGLE QUICKSTAND e Hold each side of your monitor and manually raise or lower until it is in the correct position fig T DUAL QUICKSTAND Tools 6 mm Hex Key e Remove top cover of the carriage assembly fig V e Slowly begin to turn the monitor height adjustment screw clockwise to raise the monitors and counter clockwise to lower the monitors fig W STEP 15 Adjusting Monitor Til2. Failure to comply with the instructions provided may result in property damage or serious injury Do not remove bracing box attached to QuickStand unit until your QuickStand is fully assembled STEP 1 Remove Shipping Plate Tools 6 mm Hex Key e Lay the QuickStand unit on the work surface facing up and unscrew the 2 M8 x 10 mm Cap Head Machine Screws holding the Shipping Plate in place fig A e Set aside the 2 M8 x 10 mm Cap Head Machine Screws and the Washers for Step 3 STEP 2 Attach Base Plate Tools 5 mm Hex Key e Secure the Base Plate in place using 6 M8 x 18 mm Flat Head Machine Screws fig B STEP 3 Attach Platform Tools 6 mm Hex Key e Ensure the Platform is equally spaced from the Base Plate on either side fig C e Using the 2 M8 x 10 mm Cap Head Machine Screws and the Washers from step 1 secure the Platform to the QuickStand unit STEP 4 Measure Work Surface Depth IMPORTANT Please check the depth of your work surface If you are installing a QuickStand with a Large Platform your QuickStand is pre set to attach to a 29 750 mm deep work surface If you are installing a QuickStand with a Small Platform your QuickStand is pre set to attach to a 23 600 mm deep work surface Tools Measuring Tape e The distance between the front edge of the Platform to the inside face of the Base Clamp must be equal to the work surface depth fig D e lfthe Ba
3. QuickStand INSTALLATION INSTRUCTIONS Humanscale PARTS REQUIRED Single QuickStand Parts 1 QuickStand Unit aus I Base Plate 1 Platform Palm Support VESA Plate 8 x 18 mm Flat Head Machine Screws M4 x 18 mm Pan Head Phillips 4 x 8 mm Pan Head Phillips VESA Spacer TO TMMOOU p D D Soe Se SoS a Db Additional Parts for Dual Monitor QuickStand J 1 Dual Monitor Crossbar K 1 M6 x 22 mm Flat Head Machine Screws L 2 M5 x 18 mm Flat Head Machine Screws M 2 VESA Plate N 8 M4 x 18 mm Pan Head Phillips O 8 M4 x 8 mm Pan Head Phillips P 8 VESA Spacer Tools Required aii CA 3 mm Hex Key supplied Box Knife AA 4 mm Hex Key supplied Tape Measure gt gt 5 mm Hex Key supplied 2 Phillips Screwdriver IA S 6 mm Hex Key supplied Flat Head Screwdriver m Hardware F 999999 c 3111 H 9999 Gees DO Z FAM tt 177727707 399999899 68886080888 Customer Service N America 1 800 400 0625 International 353 0 1 858 0910 www humanscale com A WARNING Read all instructions carefully before installing this product or attempting to use it This product contains a loaded mechanism that is under tension Do not attempt to remove or alter any part of this product or in any way modify or tamper with any component of this product other than as set forth in these instructions
4. rossbar for Dual Monitors Tools 3 mm Hex Key 4 mm Hex Key e Attach Dual Monitor Crossbar to QuickStand unit using the hardware kit supplied fig STEP 9 Attaching Dual Monitors et I EP Tools 2 Phillips Screwdriver 1 1 o 1 e Make sure the top of the VESA Plates are facing towards FS KP the top of the monitor before securing ls e Screw down the VESA Plates using the hardware kit supplied fig J A e Slide each monitor into the quick connector on the Dual Monitor Crossbar fig K e Plug the Power Cord and DVI cable into each monitor STEP 10 Secure Palm Support e Peel off sticker backing from Palm Support and place down in your desired position on the front edge of the Platform fig L STEP 11 Attaching USB Devices Tools Flat Head Screwdriver e Using a Flat Head Screwdriver if needed remove cable cover by tilting out from the bottom fig M e Route USB cables from keyboard and mouse into cable bracket fig N e Carefully pull cable slack through bracket until cable heads are set within Wrap remaining cable slack around bracket fig O e Replace cable bracket cover fig P STEP 12 Removing Brace Box e Remove tape and lift out box fig Q ADJUSTING QUICKSTAND In order to be able to raise and lower your QuickStand with ease it is important to spend some time adjusting the tension adjuster which can be located in the top of the QuickStand unit STEP 13
5. se Clamp is in the correct position please proceed to step 6 e Ifthe Base Clamp needs to be adjusted please proceed to step 5 STEP 5 Adjust Base Clamp for Correct Work Surface Depth Tools Measuring Tape 5 mm Hex Key e Loosen or remove the 4 M8 x 10 mm Pan Head Machine Screws and slide reposition the Base Clamp to achieve the correct work surface depth fig E NOTE If you will be installing the Grommet Mount Bolt through base instead of the clamp please refer to the Grommet Mount Bolt through kit instructions now STEP 6 Attaching QuickStand to the Work Surface IMPORTANT Your QuickStand unit is heavy If needed please have assistance when lifting e Carefully lift your QuickStand unit from its horizontal position to its vertical position fig F e Tighten the two thumbscrews to clamp your QuickStand unit to the back edge of the work surface STEP 7 Mounting Single Monitor If you are installing a dual QuickStand unit please proceed to Step 8 Tools 2 Phillips Screwdriver ci e Make sure the top of the VESA Plate is facing towards the top of the monitor before securing e Screw down the VESA Plate using the hardware kit supplied fig G e Slide the monitor into the quick connector on the QuickStand unit fig H e Plug the Power Cord and DVI Cable into the monitor e Once your monitor is in position please proceed to Step 10 STEP 8 Attaching C
6. t 15 SINGLE AND DUAL QUICKSTAND e Hold the top and bottom of your monitor and manually adjust the monitor tilt until the desired angle is achieved fig X STEP 16 Adjusting Monitor Orientation SINGLE AND DUAL QUICKSTAND e Hold each side of your monitor and manually turn the monitor until the desired orientation of either landscape or portrait is achieved fig Y STEP 17 Correctly Setting Up Your Workstation SINGLE AND DUAL QUICKSTAND e Adjust the platform until the keyboard is at or Just below elbow height e f needed manually adjust the monitor up or down until the top line of text on the screen is at eye level Humanscale HSOSI1114 Customer Service N America 1 800 400 0625 International 353 0 1 858 0910 www humanscale com
Download Pdf Manuals
Related Search