Axis T90B30
Contents
1. OG Photocell disabled 5 Lux On 15 Lux Off 10 Lux On 30 Lux Off 25 Lux On 50 Lux Off eg 9009 4d N Telemetry Input The telemetry input wires orange and purple are designed to be used with a remote switch or input from an alarm system PIR detector control room video management system or camera output The input signal can be volt free or TTL 23 AXIS T90B Series Volt free input Non polarity sensitive Short circuit Light on TTL input Orange TTL ve Purple TTL ve GND 0 V Light on 3 V Light off The telemetry input wires orange and purple are soldered together when shipped from the factory to simulate a volt free input so that the illuminator automatically turns on and off via the photocell Any remote input or switch should be connected to these wires Snip the end of the cable and separate the cables to use with remote switch or input Under normal operating conditions a telemetry input will activate the unit only at night provided that the photocell detects low light conditions However if the photocell is disabled a telemetry input will activate the unit regardless of ambient light conditions The mode of operation is selected by using the remote control The remote input can be used in conjunction with the illuminator in the following ways 1 TEL see page 24 2 DIM see page 25 3 TEL2. TIMER see page 25 Telemetry TEL Press the TEL button if the illuminator is to be turned on and off using a remote switch or input The TEL input can be used in various ways 24 AXIS T90B Series 1 Turn the light on night and off day automatically via the photocell This is the standard factory setting no further action is required 2 Turn the light on and off from a remote switch or input 3 Used in conjunction with the Timer Function to turn the light on for a pre defined period of time Telemetry DIM The remote dimming feature allows the brightness of the illuminator to be controlled remotely using the telemetry input wires Use the DIM button to select this function When the DIM function is selected a telemetry input into the illuminator will vary the brightness up and down When the telemetry input is first applied it will start to dim the light and will continue to do so while the telemetry input is active When telemetry input stops the light level will stay where it was set When the telemetry input is activated for a second time the light will start to brighten This will continue while the telemetry input is active This activation and de activation of the telemetry input Will reverse the way the light is dimmed dim down and dim up to allow the user to set exactly the level required Disable the DIM function by pressing the TEL button After setting a specific light level using the DIM functi
3. AXIS T90B Series Safety Instructions The Axis product shall be installed by a trained professional The Axis product shall be used in compliance with local laws and regulations Store the Axis product in a dry and ventilated environment Avoid exposing the Axis product to shocks or heavy pressure Do not install the product on unstable brackets surfaces or walls Use only applicable tools when installing the Axis product Excessive force could cause damage to the product Do not use chemicals caustic agents or aerosol cleaners Use a clean cloth dampened with pure water for cleaning Use only accessories that comply with technical specification of the product These can be provided by Axis or a third party Use only spare parts provided by or recommended by Axis Do not attempt to repair the product by yourself Contact Axis support or your Axis reseller for service matters Transportation When transporting the Axis product use the original packaging or equivalent to prevent damage to the product AXIS T90B Series Installation Guide This Installation Guide provides instructions for installing AXIS T90B Series Installation Steps 1 Make sure the package contents tools and other materials necessary for the installation are in order See page 7 2 Study the hardware overview See page 8 3 Study the specifications See page 14 Install the hardware See page 15 HSI19N3 Package Contents e AXIS T90
4. or closed contact input zero volt is applied Check photocell is working Cover photocell fully light should turn on It is sometimes difficult to see Infra Red lamps working in high brightness conditions Make sure that the power cable is within the specified distance Lamp Test Note Use the appropriate multimeter depending on how the illuminator is being powered AC or DC Cover the photocell fully or disable the photocell using the optional remote control and make sure the telemetry wires are shorted out or closed contact input zero volt is applied Check that the current is being drawn The amount of current will depend on the power setting of the illuminator e Setup Camera Lens and Illumination Make sure the power is set to maximum Check the orientation of illuminator and make sure it is pointing in the correct direction Check angle of the diverging lens A too narrow angle may cause hot spots and the aperture of the camera lens to close down A too wide angle may cause insufficient light on the scene 28 AXIS T90B Series e Remote Control optional accessory Press the STATUS button to check the status of the remote control see LED Status Indicators Programming may be disabled Turn the illuminator power off for at least 10 seconds and then turn the power on to enter Programming Mode In bright sunlight conditions the distance between the remote control and the illuminator may need to be reduc
5. 11 AXIS T90B Series Date May 2014 Axis Communications AB 2014 Part No 57589
6. B Illuminator including power cable 1 pre mounted diverging lens 2 separate diverging lenses Optional Accessories e Mounting brackets e Remote control Diverging lens with additional angle Power supply For information about available accessories see www axis com AXIS T90B Series Hardware Overview Illuminator 1 2 AXIS 3 1 Photocell 2 Cable 3 Breather gland 1 2 3 4 5 6 Power cable red Power cable black Photocell cable white Photocell cable yellow Telemetry cable purple Telemetry cable orange AXIS T90B Series HSI19N3 AXIS T90B Series O1 N Red LED indicator Amber LED indicator Green LED indicator Remote control receiver Mounting bracket pre mounted 10 AXIS T90B Series AXIS T90B40 IR LED HSI19N3 1 Cables 2 Mounting bracket pre mounted 3 Bolt Optional Accessories Remote Control For information how to use the remote control see Access the Product 11 AXIS T90B Series Qo Mounting Brackets POWER PHOTOCELL TIMER e eee TELEMETRY z 9 5 8000000 Q POWER ADJUST buttons PHOTOCELL ADJUST buttons TIMER buttons Photocell disable button DIM button RESET button STATUS button Disable remote control setup button TELEMETRY but
7. COMMUNICATIONS AXIS T90B Series AXIS T90B15 W LED AXIS T90B25 W LED AXIS T90B35 W LED AXIS T90B20 IR LED AXIS T90B30 IR LED AXIS T90B40 IR LED Installation Guide HSI15N3 Legal Considerations Video and audio surveillance can be regulated by laws that vary from country to country Check the laws in your local region before using this product for surveillance purposes Liability Every care has been taken in the preparation of this document Please inform your local Axis office of any inaccuracies or omissions Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice Axis Communications AB makes no warranty of any kind with regard to the material contained within this document including but not limited to the implied warranties of merchantability and fitness for a particular purpose Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing performance or use of this material This product is only to be used for its intended purpose Intellectual Property Rights Axis AB has intellectual property rights relating to technology embodied in the product described in this document In particular and without limitation these intellectual property rights may include one or more of the patents listed at www axis com patent htm and one or
8. Risk group 2 IEC EN 60529 IP66 REACH WEEE CE Valid only for IR LED products Operating conditions 50 to 50 58 F to 122 F 10 100 RH condensing 32 AXIS T90B Series Dimensions HxWxL The size of the product shall be maximum WxHxL AXIS T90B15 W LED 75 x 100 x 64 mm 3 x 4x2 5 in AXIS T90B25 W LED 5 x 2 5 AXIS T90B35 W LED 7 3 2 AXIS T90B20 IR LED 5 x 2 5 AXIS T90B30 IR LED 7 3 2 AXIS T90B40 IR LED x 9 x 3 100 x 135 x 66 mm 4 x 135 x 180 x 68 2 mm 5 x 100 x 135 x 66 mm 4 x 135 x 180 x 68 2 5 x HSI19N3 279 x 223 x 68 mm 11 Weight AXIS T90B15 W LED AXIS T90B25 W LED AXIS T90B35 W LED AXIS T90B20 IR LED AXIS T90B30 IR LED AXIS T90B40 IR LED 600 g 1 3 lbs 950 2 1 lbs 1650 g 3 6 lbs 950 g 2 1 lbs 1650 3 6 lbs 4500 9 9 lbs Included accessories 3 diverging lenses 35 pre mounted 60 80 Optional accessories Power supply Mounting brackets AXIS T90B Remote Control Diverging lens 120 angle Further Information Visit Axis learning center www axis com academy for useful trainings webinars tutorials and guides 33 AXIS T90B Series Warranty Information For information about Axis product warranty and thereto related information see www axis com warranty 34 35 Installation Guide Ver M1
9. S T90B Series Distance AXIS T90B20 IR LED 10 x10 120 m 394 ft 35 x10 65 m 213 ft 60 x25 45 m 148 ft 80 x30 30 m 98 ft 120 x50 20 m 66 ft AXIS T90B30 IR LED 10 x10 220 m 722 ft 35 x10 120 m 394 ft 60 x25 65 m 213 ft 80 x30 45 m 148 ft 120 x50 30 m 98 ft AXIS T90B40 IR LED 10 x10 310 m 1010 35 x10 170 m 551 ft 60 x25 112 m 367 ft 80 x30 70 m 230 ft 120 x50 65 213 ft AXIS T90B15 W LED 10 x10 50 m 164 35 x10 35 m 115 ft 60 x25 20 66 ft 80 x30 15 m 49 ft 120 x50 10 m 33 ft AXIS T90B25 W LED 10 x10 90 m 295 35 x10 55 m 180 ft 60 x25 30 m 98 ft 80 x30 20 m 66 ft 120 x50 15 m 49 AXIS T90B35 W LED 10 x10 150 m 492 35 x10 80 m 262 ft 60 x25 45 m 148 ft 31 HSI19N3 AXIS T90B Series 80 x30 30 m 98 ft 120 x50 20 m 66 No diverging lens Optional accessory Casing Material Polycarbonate IR LED Black W LED White and silver Display and indicators LED indicators Environment Outdoor Mounting Wall Ceiling Column Camera housing Approvals EN 55022 Class B EN 55024 EN 61547 EN 55015 EN 50130 4 C tick AS NZS CISPR 22 Class B FCC Part 15 Subpart B Class B ICES 003 Class B KCC KN22 Class B KN24 IEC EN 60598 1 IEC EN 62471
10. be connected using a shielded network cable STP that is properly grounded Cet appareil num rique de la classe B est confome la norme NMB 003 du Canada Le produit doit tre connect l aide d un c ble r seau blind STP qui est correctement mis la terre Europe This digital equipment fulfills the requirements for RF emission according to the Class B limit of EN 55022 The product shall be connected using a shielded network cable STP that is properly grounded This product fulfills the requirements for immunity according to EN 61000 6 1 residential commercial and light industrial environments This product fulfills the requirements for immunity according to EN 61000 6 2 industrial environments Australia New Zealand This digital equipment fulfills the requirements for RF emission according to the Class B limit of AS NZS CISPR 22 The product shall be connected using a shielded network cable STP that is properly grounded Korea 0 217 2 7FSS Bg 677 A FE IYA ASE AS BE 1 I STP shielded twisted pair 0 amp amp ASS AZ Safety Photobiological Safety This product fulfills the requirements for photobiological safety according to IEC EN 62471 risk group 2 Disposal and Recycling When this product has reached the end of its useful life dispose of it according to local laws and regulations For information about your nea
11. e illuminator has been programmed the settings will be stored in a non volatile stored memory These settings are saved and reloaded if the illuminator experiences loss of power Press the RESET button to restore the illuminator back to the factory default settings HSI19N3 Disable Remote Control Setup Note To enable Programming Mode after remote setup has been disabled the illuminator must be powered off for at least 10 seconds When turned on the illuminator automatically re enters Programming Mode Disable remote setup once an individual illuminator has been programmed and is delivering the required operating performance This will help to avoid tampering and the possibility of receiving commands when programming other illuminators in close proximity Lock the illuminator settings by pressing the Disable Remote Setup button continuously for at least 4 seconds If remote control setup is not disabled the illuminator will remain in Programming Mode for a pre determined time of 4 weeks After 4 weeks remote control setup will be automatically disabled Troubleshooting Ensure all tests are undertaken by a qualified trained engineer Ensure safe working practices are followed at all times 27 AXIS T90B Series Basics Check the LED status indicator See LED Indicators Check polarity of lamp connection red ve black ve Ensure power is 12 24 V AC or DC Ensure telemetry wires are shorted out
12. ed Check the battery on the remote control CR2025 replace if necessary Make sure no other strong Infra Red source is pointing at the remote receiver Make sure there is a clear line of site between the illuminator and the remote control Check the remote control battery Technical Specifications Models AXIS T90B15 W LED AXIS T90B25 W LED AXIS T90B35 W LED AXIS T90B20 IR LED AXIS T90B30 IR LED AXIS T90B40 IR LED Supported cameras IR LED All Axis cameras with IR cut filter W LED All Axis network cameras 29 HSITSN4 AXIS T90B Series Power Input Voltage 12 24 V AC DC AC Frequenzy 50 60 Hz Cable length 2 5 m 8 ft Power Consumption maximum light 2090 of maximum light Standby mode AXIS T90B15 W LED 12 W 3 W 0 15 W AXIS T90B25 W LED 24 W 6 W d dd AXIS T90B35 W LED 48 W 12 0 15 W AXIS T90B20 IR LED 24 6 W 15 W AXIS 90 30 IR LED 24 W 12 W 0 15 W AXIS T90B40 IR LED 96 W 24 W 0 15 W Control technology Type Power level Photocell sensitivity Telemetry link for remote activation if required Timer IR LED 850 nm semi covert W LED luminous power AXIS T90B15 W LED 733 Im AXIS T90B25 W LED 1452 Im AXIS T90B35 W LED 2840 Im Color temperature 5700 K valid for W LED versions only Angle 10 without diverging lens With diverging lenses 35 60 80 120 Optional accessory 30 AXI
13. eries 1 Screws 2 Diverging lens Note Adjust the vertical position of the illuminator to ensure that the field of view of the camera is illuminated AXIS T90B Series 4 Position the illuminator adjacent to the camera and point the illuminator towards the scene HSI19N3 Red cable ve Black cable ve polarity sensitive 5 Mount the power supply 6 Connectthe illuminator to the power supply 19 AXIS T90B Series 1 Illuminator 2 Power cable 3 Power supply 7 Set photocell following output White amp Yellow Volt free output normally open day to normally closed night Connect direct to camera if required to control switchover of day night cameras Access the Product Programming Mode The illuminator has the following default settings e Power set to maximum 100 Photocell set to medium sensitivity level 10 lux On 30 lux Off e Timer disabled 20 AXIS T90B Series e Telemetry TEL enabled e Telemetry input wires soldered together for automatic photocell operation Telemetry DIM disabled e LED status indicators enabled Programming Mode Note Changing the settings requires a remote control optional accessory The illuminator must be in Programming Mode HSI19N3 The illuminator automatically switches from Programming Mode to Normal Operating Mode after 4 weeks To switch to Programming Mode restart the illuminator 1 Adjust the power see P
14. ies 50 C to 50 C 10 100 RH 58 F to 122 F densing Power Consumption Product Value AXIS T90B15 W LED 12 24 V AC DC max 12 W AXIS T90B20 IR LED 12 24 V AC DC max 24 W 14 AXIS T90B Series AXIS T90B25 W LED 12 24 V AC DC max 48 W AXIS T90B30 IR LED 12 24 V AC DC max 24 W AXIS T90B35 W LED 12 24 V AC DC max 48 W AXIS T90B40 IR LED 12 24 V AC DC 96 W For more information about power consumption see Technical Specifications on page 29 Install the Hardware To install the product using a compatible bracket from AXIS T90B Mounting Accessories see the Installation Guide delivered separately with the mounting bracket ej 15 15 HSI19N3 AXIS T90B Series IR emitted from this product Avoid prolonged eye exposure or use appropriate shielding or eye protection at distances of less than 1 5 m Follow these installation procedures 1 If required remove the screws and move the standard bracket to the top of the illuminator 2 If required loosen the screws and turn the bracket 90 16 AXIS T90B Series If required loosen the screws and change to a diverging lens with the desired angle of illumination The angle of illumination should be adjusted according to the camera field of view to light the whole scene adequately See Technical Specifications 17 HSI19N3 AXIS T90B S
15. more additional patents or pending patent applications in the US and other countries Equipment Modifications This equipment must be installed and used in strict accordance with the instructions given in the user documentation This equipment contains no user serviceable components Unauthorized equipment changes or modifications will invalidate all applicable regulatory certifications and approvals Trademark Acknowledgments AXIS COMMUNICATIONS AXIS ETRAX ARTPEC and VAPIX are registered trademarks or trademark applications of Axis AB in various jurisdictions All other company names and products are trademarks or registered trademarks of their respective companies Regulatory Information Europe C This product complies with the applicable CE marking directives and harmonized standards Electromagnetic Compatibility EMC Directive 2004 108 EC See Electromagnetic Compatibility EMC on page 2 Low Voltage LVD Directive 2006 95 EC See Safety on page 3 Restrictions of Hazardous Substances RoHS Directive 2011 65 EU See Disposal and Recycling on page 3 A copy of the original declaration of conformity may be obtained from Axis Communications AB See Contact Information on page 3 Electromagnetic Compatibility EMC This equipment has been designed and tested to fulfill applicable standards for Radio frequency emission when installed according to the instructions and used in its intended environme
16. nt Immunity to electrical and electromagnetic phenomena when installed according to the instructions and used in its intended environment USA This equipment has been tested using a shielded network cable STP and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The product shall be connected using a shielded network cable STP that is properly grounded Canada This Class B digital apparatus complies with Canadian ICES 003 The product shall
17. on if DIM is disabled and TEL enabled the last power level set when using the DIM function will be remembered and used by the system unless a new power adjust button is selected Timer The timer function allows the illuminator to be triggered via a telemetry input and remain on for a pre defined period of time There are four pre defined times and a timer disable function To select timer function first press and release the TEL button then select the duration of the timer as shown below 25 HSI19N3 AXIS T90B Series If you wish to cancel the timer period and have the illuminator operate under standard telemetry conditions press Timer Disabled rower moren mmer N ee GO 5 2 NE HOO d 4 Timer disabled 1 minute 3 minutes 10 minutes 30 minutes TEL button HS O LED Status Indicators This status indicator function can be switched on and off by pressing the STATUS button This is the only button that has two states It is possible for this function to be enabled even if Programming Mode has been disabled so the status of the illuminator can be checked at any time 26 AXIS T90B Series Factory Default Note To activate this feature the button must be pressed continuously for 4 seconds This is to avoid the possibility of activating this feature accidentally Once th
18. ower Adjust on page 22 2 Adjust the photocell sensitivity see Photocell Sensitivity on page 22 3 Setthe telemetry input TEL see page 24 DIM see page 25 u Timer see page 25 4 Disable the LED status indicators see LED Status Indicators on 26 5 Disable remote control setup see Disable Remote Control Setup on page 27 6 Restore the factory default settings see Factory Default on page 27 Normal Operating Mode The only function of the Remote Control available during Normal Operating Mode is LED Status Indicators see LED Status Indicators on page 26 21 AXIS T90B Series Power Adjust The power output of the illuminator can be adjusted between five pre set levels Select the required light intensity by using the buttons below POWER PHOTOCELL TIMER ee ee ECCO 7600000 20 4096 6096 8096 100 of maximum DE Co No za Photocell Sensitivity Note When the photocell is disabled the illuminator will turn on and off from a telemetry input regardless of ambient lighting conditions 22 AXIS T90B Series There are three pre defined levels to set the lux level threshold at which the photocell turns the illuminator on or off Select the required sensitivity level by using the buttons below JC NO NO a
19. rest designated collection point contact your local authority responsible for waste disposal In accordance with local legislation penalties may be applicable for incorrect disposal of this waste Europe E Wm his symbol means that the product shall not be disposed of together with household or commercial waste Directive 2012 19 EU on waste electrical and electronic equipment WEEE is applicable in the European Union member states To prevent potential harm to human health and the environment the product must be disposed of in an approved and environmentally safe recycling process For information about your nearest designated collection point contact your local authority responsible for waste disposal Businesses should contact the product supplier for information about how to dispose of this product correctly This product complies with the requirements of Directive 2011 65 EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS China 9 This product complies with the requirements of the legislative act Administration on the Control of Pollution Caused by Electronic Information Products Contact Information Axis Communications AB Emdalav gen 14 223 69 Lund Sweden Tel 46 46 272 18 00 Fax 46 46 13 61 30 www axis com Support Should you require any technical assistance please contact your Axis reseller If your questions cannot be ans
20. ton To install the product using a compatible bracket from AXIS T90B Mounting Accessories see the Installation Guide delivered separately with the mounting bracket 12 LED Indicators There are three colored LED indicators on the base of the illuminator which AXIS T90B Series provide operating and status information The color status depends on the current operating mode Programming Mode e Normal Operating Mode Programming Mode LED Indicator Indicated Behavior Solid Green Power on Flashing Green Remote control IR receiver error Solid Amber Illuminator receiving valid command from remote control Flashing Amber Illuminator in Programming Mode Solid Red Internal LED error Flashing Red Input voltage supply error Normal Operating Mode LED Indicator Indicated Behavior Solid Green Power on Flashing Green Remote control IR receiver error HSI19N3 AXIS T90B Series Normal Operating Mode Continued Solid Amber Input voltage level error Solid Red Internal LED error Once the voltage error has been corrected disable the remote control setup or restart the illuminator to turn the status LED off Connectors and Buttons For specifications and operating conditions see page 14 Power Connector e AC DC power connector Specifications Operating Conditions Product Temperature Humidity AXIS T90B Ser
21. wered immediately your reseller will forward your queries through the appropriate channels to ensure a rapid response If you are connected to the Internet you can L download user documentation and software updates find answers to resolved problems in the FAQ database Search by product category or phrase report problems to Axis support staff by logging in to your private support area chat iti Axis support staff selected countries visit Axis Support at www axis com techsup Learn More Visit Axis learning center www axis com academy for useful trainings webinars tutorials and guides AXIS T90B Series Safety Information Read through this Installation Guide carefully before installing the product Keep the Installation Guide for future reference Hazard Levels ADANGER Indicates a hazardous situation which if not avoided will result in death or serious injury m z AWARNING Indicates a hazardous situation which if not avoided could result in death or serious injury Indicates a hazardous situation which if not avoided could result in minor or moderate injury Indicates a situation which if not avoided could result in damage to property Other Message Levels Important Indicates significant information which is essential for the product to function correctly Note Indicates useful information which helps in getting the most out of the product
Download Pdf Manuals
Related Search