Home

Gigabyte GA-H97N-WIFI motherboard

1. d You may clear the CMOS values by removing the battery 1 Tum off your computer and unplug the power cord 2 Gently remove the battery from the battery holder and wait for one minute i Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 3 Replace the battery 4 Plug in the power cord and restart your computer DES Always turn off your computer and unplug the power cord before replacing the battery A e Replace the battery with an equivalent one Danger of explosion if the battery is replaced with an incorrect model e Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model e When installing the battery note the orientation of the positive side and the negative side of the battery the positive side should face Used batteries must be handled in accordance with local environmental regulations Hardware Installation 24 0 1 2 3 4 5 SATA 6Gb s Connectors SATA connectors conform to SATA6Gb s sta
2. co II Bo ND e Do not plug the IEEE 1394 bracket 2 5 cable into the USB 2 0 1 1 header e Prior to installing the USB bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket 12 COM Serial Port Header The COM header can provide one serial port via an optional COM port cable For purchasing the optional COM port cable please contact the local dealer Pin No Definition NDCD NSIN NSOUT NDTR GND NDSR NRTS 5 NRI No Pin CO II BR ND gt Hardware Installation 28 13 CLR_CMOS Clear CMOS Jumper Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults To clear the CMOS values use a metal object like a screwdriver to touch the two pins for a few seconds Open Normal a Sho
3. lt Profile DDR Voltage When using a non XMP memory module or Extreme Memory Profile X M P is set to Disabled the value is displayed according to your memory specification When Extreme Memory Profile X M P is set to Profile1 or Profile2 the value is displayed according to the SPD data on the XMP memory Channel Interleaving Enables or disables memory channel interleaving Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability Auto lets the BIOS automatically configure this setting Default Auto 7 Rank Interleaving Enables or disables memory rank interleaving Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability Auto lets the BIOS automatically configure this setting Default Auto Channel A B Memory Sub Timings GIGABYTE DualBIOS ID m amp o b A PS System Information BIOS Features Peripherals Power Management Save amp Exit o Back M I T Aduanced Memory Settings Channel Memory Sub Timings ST Mode English Q Flash Memory Timing Mode Auto Auto This sub menu provides memory timing settings for each channel of memory This sub menu provides memory timing settings for each channel of memory The respective timing setting screens are configurable only when Memory Timing Mode is set to Manual or Advanced Manual Note Your system may become unstable or
4. e Saudi Arabia WEB address http www gigabyte com sa Gigabyte Technology Pty Ltd Australia WEB address http www gigabyte com au Appendix G B T TECHNOLOGY TRADING GMBH Germany WEB address http www gigabyte de G B T TECH CO LTD U K WEB address http www giga byte co uk Giga Byte Technology B V The Netherlands WEB address http www giga byte nl GIGABYTE TECHNOLOGY FRANCE France WEB address http www gigabyte fr Sweden WEB address http www gigabyte se Italy WEB address http www giga byte it e Spain WEB address http www giga byte es Greece WEB address http www gigabyte com gr Czech Republic WEB address http www gigabyte cz e GIGABYTE Global Service System eu Global Technical Service Welcome to GIGABYTE Service system If you are a GIGABYTE Passport member please login with your GIGABYTE membership E Mail address and password Otherwise you can simply enter E Mail address to login NN M English Deutsch EPI Appendix e Hungary WEB address http www giga byte hu Turkey WEB address http www gigabyte com tr Russia WEB address http www gigabyte ru Poland WEB address http www gigabyte pl Ukraine WEB address http www gigabyte ua Romania WEB address http www gigabyte com ro Serbia WEB address http www gigabyte
5. 1xDVI I port supporting a maximum resolution of 1920x1200 60Hz 2 x HDMI ports supporting a maximum resolution of 4096x2160 24Hz or 2560x1600 60Hz Support for HDMI 1 4a version Support for up to displays at the same time To set up a triple display configuration you must connect a D Sub monitor using a DVI to D Sub adapter Maximum shared memory of 1 GB Audio Realtek ALC892 codec High Definition Audio 2 4 5 1 7 1 channel Support for S PDIF Out Intel GbE LAN chip 10 100 1000 Mbit LAN1 LAN Atheros GbE LAN chip 10 100 1000 Mbit LAN2 Wi Fi 802 11 a b g n ac supporting 2 4 5 GHz Dual Band Bluetooth 4 0 3 0 HS 2 1 EDR Support for 11ac wireless standard and up to 867 Mbps data rate Actual data rate may vary depending on environment and equipment Wireless Communication Module Expansion Slots 1x PCI Express x16 slot running at x16 The PCIEX16 slot conforms to PCI Express 3 0 standard 1xmini PCI Express slot for the wireless communication module Storage Interface Chipset 6x SATA 660 5 connectors Support for RAID 0 RAID 1 RAID 5 and RAID 10 Only for GA Z97N WIFI Only for GA H97N WIFI Hardware Installation 10 USB Chipset 4x USB 2 0 1 1 ports 2 ports on the back panel 2 ports available through the internal USB header 6x USB 3 0 2 0 ports 4 ports on the back panel 2 ports available th
6. 20 ec CNN 2 7 Power Management JE c ne 36 Chapter 3 Configuring SATA Hard Drive s 97 3 1 Configuring SATA Controllers 57 3 2 Installing the SATA RAID AHCI Driver and Operating System 69 AODEM eo nu 19 73 Regulatory Statements nnne 74 a a a en 79 Box Contents GA Z97N WIFI GA H97N WIFI motherboard Motherboard driver disk Wireless module driver disk User s Manual Quick Installation Guide Two SATA cables O Shield One antenna The box contents above are for reference only and the actual items shall depend on the product package you obtain The box contents are subject to change without notice Optional Items 2 port USB 2 0 bracket Part No 12CR1 1UB030 6 R eSATA bracket Part No 12CF1 3SATPW 4 R 3 5 Front Panel with 2 USB 3 0 2 0 ports Part No 12CR1 FPX582 2 R HDMI to DVI adapter Part No 12CT2 HDMI01 1 R COM port cable Part No 12CF1 1CM001 3 R GA Z97N WIFI GA H97N WIFI Motherboard Layout COM SYS FAN CPU FAN DDR3 1 DDR3 2 TE 12V CMOS WIFI Module cdm 5 2 9 DVI DOUBLE HIPMI GA Z97N WIFI GA H97N WIFI FE SATA3
7. Address No 6 Bao Chiang Road Hsin Tien Dist New Taipei City 231 Taiwan TEL 886 2 8912 4000 FAX 886 2 8912 4005 Tech and Non Tech Support Sales Marketing http ggts gigabyte com tw WEB address English http www gigabyte com WEB address Chinese http www gigabyte tw INC U S A TEL 1 626 854 9338 FAX 1 626 854 9326 Tech Support http ggts gigabyte com tw Warranty Info http rma gigabyte us Web address http www gigabyte us G B T INC USA Mexico Tel 1 626 854 9338 x 215 Soporte de habla hispano FAX 1 626 854 9326 Correo soporte gigabyte usa com Tech Support http rma gigabyte us Web address http latam giga byte com e Giga Byte SINGAPORE PTE LTD Singapore WEB address http www gigabyte sg Thailand WEB address http th giga byte com Vietnam WEB address http www gigabyte vn Em e NINGBO G B T TECH TRADING CO LTD China WEB address http www gigabyte cn Shanghai TEL 86 21 63400912 FAX 86 21 63400682 Beijing TEL 86 10 62102838 FAX 86 10 62102848 Wuhan TEL 86 27 87685981 FAX 86 27 87579461 GuangZhou TEL 86 20 87540700 FAX 86 20 87544306 Chengdu TEL 86 28 85483135 FAX 86 28 85256822 Xian TEL 86 29 85531943 FAX 86 29 85510930 Shenyang TEL 86 24 83992342 FAX 86 24 83992102 GIGABYTE TECHNOLOGY INDIA LIMITED India WEB address http www gigabyte in
8. Atherose BAT Intele GbE LAN Ll fre Intele Z970 Super I D Intele H97 F AUDIO SPDIF O PCIEX16 B BIOS _ 0 CODEC 7 CI amp HI w C ea 7 D t a L C7 Only for GA Z97N WIFI Only for GA H97N WIFI GA Z97N WIFI GA H97N WIFI Motherboard Block Diagram PCI Express Bus CPU CLK 100 MHz 16 LGA1150 1 PCI Express x16 CPU DDR3 1600 1333 MHz tila Dual Channel Memory HDMI ww PCle CLK 100 MHz LL Pasos LAN1 LAN 6 SATA 6Gb s RJ45 RJ45 PCIe CLK 100 MHz Intel GbE Atheros Intel Z97 GbE LAN Intele H97 x1 PCI Express Bus 4 USB 2 0 1 1 bi LPC Mini PCle WiFi Bus iTE gang Super 2 RE CODEC PS 2 KB Mouse 555 O55 5 O 555 25 amp BEB Center Subwoofer Speaker Out Only for GA Z97N WIFI Only for GA H97N WIFI ER For detailed product information limitation s refer to 1 2 Product Specifications JB Chapter 1 Hardware Installation 1 1 The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge ESD Prior to installation carefully read the user s Installation Precautions manual and follow these procedures Prior to installation make sure the chassis is suitable for the motherboard Prior to installation do
9. CPU that supports this function This feature only works for operating systems that support multi processor mode Auto lets the BIOS automatically configure this setting Default Auto lt CPU Enhanced Halt C1E Note 1 Enables or disables Intel CPU Enhanced Halt C1E function a CPU power saving function in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption Auto lets the BIOS automatically configure this setting Default Auto 7 C3 State Support Note 1 Allows you to determine whether to let the CPU enter C3 mode in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption The C3 state is a more enhanced power saving state than C1 Auto lets the BIOS automatically configure this setting Default Auto 7 C6 C7 State Support Note 1 Allows you to determine whether to let the CPU enter C6 C7 mode in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption The C6 C7 state is a more enhanced power saving state than C3 Auto lets the BIOS automatically configure this setting Default Auto CPU Thermal Monitor Note 1 Enables or disables Intel Thermal Monitor function a CPU overheating protection function When enabled the CPU core frequency and voltage will be reduced when the CPU is
10. Cloud Station ON OFF Charge Smart TimeLock Smart Recovery 2 System Information Viewer USB Blocker Support for Q Flash Support for Smart Switch Support for Xpress Install Bundled Norton Internet Security OEM version Software Intel Rapid Start Technology Intel Smart Connect Technology Intel Smart Response Technology Intel Small Business Advantage Intel Wireless Display qug Operating Support for Windows 8 1 8 7 System Form Factor Mini ITX Form Factor 17 0cm x 17 0cm GIGABYTE reserves the right to make any changes to the product specifications and product related information without prior notice Please visit the Support amp Downloads Utility page on GIGABYTE s website to check the supported operating system s for the software listed in the Unique Features and Bundled Software columns Only for GA H97N WIFI Hardware Installation 12 1 3 Installing the CPU and CPU Cooler Read the following guidelines before you begin to install the CPU e Make sure that the motherboard supports the CPU Go to GIGABYTE s website for the latest CPU support list e Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage Locate the pin one of the CPU The CPU cannot be inserted if oriented incorrectly Or you may locate the notches on both sides of the CPU and alignment keys on
11. gt gt Wake up day Turn on the system at a specific time on each day or on a specific day in a month Wake up hour minute second Set the time at which the system will be powered on automatically Note When using this function avoid inadequate shutdown from the operating system or removal of the AC power or the settings may not be effective Wake on LAN Enables or disables the wake on LAN function Default Enabled Soft Off by PWR BTTN Configures the way to turn off the computer in MS DOS mode using the power button gt gt Instant Off Press the power button and then the system will be turned off instantly Default Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system If the power button is pressed for less than 4 seconds the system will enter suspend mode RC6 Render Standby Allows you to determine whether to let the onboard graphics enter standby mode to decrease power consumption Default Enabled AC BACK Determines the state of the system after the return of power from an AC power loss Always Off The system stays off upon the return of the AC power Default Always On The system is turned on upon the return of the AC power Memory The system returns to its last known awake state upon the return of the AC power BIOS Setup 54 Power On Keyboard Allows the system to be turned on by a PS 2 keyboard wake up event Note To use this function you need an ATX p
12. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it For HD Front Panel Audio For AC 97 Front Panel Audio Eu ESE Pin No Definition Pin No Definition H 1 MIC2L 1 MC 2 GND 2 GND H g 1 3 MIC2R 3 MIC Power 1 4 ACZ DET 4 NC l 5 5 Line Out R 6 GND 6 NC 7 FAUDIO JD 7 NC 8 NoPin 8 NoPin 9 LINE2L 9 Line Out L 10 GND 10 NC ER The front panel audio header supports HD audio by default Audio signals will be present on both of the front and back panel audio connections simultaneously e Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug For information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 25 Hardware Installation 8 F_PANEL Front Panel Header Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below Note the
13. System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Copyright C 2014 Ame Figure 5 Configuring SATA Hard Drive s 60 Step 5 After setting the capacity move to Create Volume and press lt Enter gt to begin Figure 6 GIGABYTE DualBIOS Sh Name RAID Level Select Disks SATA 0 0 Hitachi HDS721050CLA660 JP1532FR3BKRJK 465 76 SATA 0 1 Hitachi HDS 21050CLA660 JP1532ER04EJTK 465 7GB Strip Size Capacity Copyright 2014 American Megatrends Figure 6 Create a volume with the settings specified above Select Screen 11 Click Select Item Enter Dbl Click Select PU PD Change Opt F2 Smart Tweak Mode F5 Previous Values F Optimized Defaults F8 Q Flash F9 System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit After completing you ll be brought back to the Intel R Rapid Storage Technology screen Under RAID Volumes you can see the new RAID volume To see more detailed information press Enter on the volume to check for information on RAID level stripe block size array name and array capacity etc Figure 7 Volume Actions 0 0 M M RAID Level Strip Size Size Status Bootable GIGABYTE DualBIOS Volumel RAIDO Str ipe 16KB 931 56B Normal Yes gt SATA 0 0 Hitachi HDS721050CLA660 JP1532FR3BKRJK
14. 2 0 ports please contact the local dealer Pin No Definition Pin No Definition 1 VBUS 11 D2 2 2 SSRXt 12 02 __ 3 SSRX1 13 GND 4 GND 14 SSTX2 5 SSTX1 15 SSTX2 1 6 SSTX1 16 GND T i 7 GND 17 SSRX2 8 D1 18 SSRX2 9 D1 19 VBUS 10 NC 20 NoPin Prior to installing the USB front panel be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB front panel 27 Hardware Installation 11 F_USB USB 2 0 1 1 Header The header conforms to USB 2 0 1 1 specification Each USB header can provide two USB ports via an optional USB bracket For purchasing the optional USB bracket please contact the local dealer m pr Pin No Definition Power 5V Power 5V USB DX USB DY USB DX USB DY GND GND No Pin NC 10 8 19 2 _ 1
15. 465 7GB gt SATA 0 1 Hitachi HDS721050CLA660 JP1532EROA4EJTK 465 7GB Copyright C 2014 American Megatrends Inc Figure 7 61 Select Screen 11 Click Select Item Enter Dbl Click Select PU PD Change Opt F2 Smart Tweak Mode F5 Previous Values F Optimized Defaults F8 Q Flash F9 System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Configuring SATA Hard Drive s Delete RAID Volume To delete a RAID array press lt Enter gt on the volume to be deleted on the Intel R Rapid Storage Technology screen After entering the RAID VOLUME INFO screen press lt Enter gt on Delete to enter the Delete screen Press Enter on Yes Figure 8 GIGABYTE DualBIOS f gt 3 O v 49 A z Sustem Information BIOS Features Power Management save amp Exit Back Peripherals Intel Rapid Storage Technology RAID VOLUME INFO Delete ST Mode English Q Flash Delete the RAID volume ALL DATA ON VOLUME WILL BE LOST gt Yes Figure 8 Configuring SATA Hard Drive s 62 C 2 Configuring Legacy RAID Enter the Intel legacy RAID BIOS setup utility to configure a RAID array Skip this step and proceed with the installation of Windows operating system for a non RAID configuration Step 1 After the POST memory test begins and before the operating system boot begins look for a message which says Pre
16. D L gs 1 8 2003 n 259 article 104 activity subject to general authorization for outdoor use and article 105 free use for indoor use in both cases for private use 2 D M 28 5 03 for supply to public of RLAN access to networks and telecom services L uso degli apparati regolamentato da 1 D L gs 1 8 2003 n 259 articoli 104 attivit soggette ad autorizzazione generale se utilizzati al di fuori del proprio fondo e 105 libero uso se utilizzati entro il proprio fondo in entrambi i casi per uso private 2 28 5 03 per la fornitura al pubblico dell accesso R LAN alle reti e ai servizi di telecomunicazioni Appendix 16 Taiwan NCC Wireless Statements 242 zt ff amp 4 AE BJ KIS EE N E REOS P HIR EUSEB JERIT Foe HE Ko HIE JS ic SELMER Ze RAB AE NGA WEN NEAR FER ADH RE Tatts SAA c SE HA BS SUSCI E HIT TR EB PSC MT LB 4 7 1 5 25 5 35 Korea NCC Wirel ment 5 25GHz 5 35 GHz CHAS NB TA IE LRO AS HEHE LICE Japan Wireless Statement 5 15GHz fi 5 35CHz fT Appendix Appendix 220 Contact Us e GIGA BYTE TECHNOLOGY CO LTD
17. DATA ON SELECTED DISKS WILL BE LOST TAB Next ESC Previous Menu ENTER Select Figure 13 When completed you can see detailed information about the RAID array in the DISK VOLUME INFORMATION section including the RAID level stripe block size array name and array capacity etc Figure 14 1 Create RAID Volume Recovery Volume Options 2 Delete RAID Volume Acceleration Options 3 Reset Disks to Non RAID Exit DISK VOLUME INFORMATION RAID Volumes ID Name Level Strip Size Status Bootable 0 Volume0 RAID0 Stripe 128KB 931 5GB Yes Physical Devices ID Device Model Serial Size Type Status Vol ID 1 Hitachi HDS72105 JP1532FR3BWV7K 465 7GB 2 Hitachi HDS72105 JP1532ER046M2K 465 7GB TL ESC Exit ENTER Select Menu Figure 14 To exit the RAID BIOS utility press lt Esc gt or select 6 Exit in MAIN MENU Now you can proceed to install the SATA RAID AHCI driver and operating system 65 Configuring SATA Hard Drive s Recovery Volume Options Intel Rapid Recover Technology provides data protection by allowing users to easily restore data and system operation using a designated recovery drive With the Rapid Recovery Technology which employs RAID 1 functionality users can copy the data from the master drive to the recovery drive if needed the data on the recovery drive can be restored back to the master drive Before you begin The recovery drive must have equ
18. Delete RAID Volume To delete a RAID array select Delete RAID Volume in MAIN MENU and press lt Enter gt In the DELETE VOLUME MENU section use the up or down arrow key to select the array to be deleted and press Delete When prompted to confirm your selection Figure 19 press lt gt to confirm or lt N gt to abort DELETE VOLUME MENU Level Drives Capacity Status Bootable Volume0 RAIDO Stripe 2 931 5GB Normal Yes ALL DATA IN THE VOLUME WILL BE LOST Deleting a volume will reset the disks to non RAID ALL DISK DATA WILL BE DELETED This does not apply to Recovery volumes ESC Exit DEL Delete Volume Figure 19 Acceleration Options This option allows you to view the status of your accelerated drive volume Figure 20 created using the Intel IRST utility In case you are unable to run the Intel IRST utility due to an application error or operating system issue you will need to remove acceleration or manually enable synchronization Maximized mode only using this option in the RAID ROM utility Steps Select Acceleration Options in MAIN MENU and press lt Enter gt To remove the acceleration select the accelerated drive volume press lt gt and press lt gt to confirm To synchronize data from the cache device to the accelerated drive volume press lt 5 gt and press lt gt to confirm SI ACCELERATION OPTIONS Name y Capacity Mode Status DISK P
19. Hardware Playbeck Recording Sounds Conmuricatons and Sound gt Sound gt Playback set Intel R Display Audio aa ROM to the default playback device peakers Realtek High Definition Audio Not plugged in Realtek Digital Output Realtek High Definition Audio Ready Realtek Digital Output Optical Realtek High Definition Audio Configure Set Default v Properties Ko 19 Hardware Installation Triple Display Configurations for the Onboard Graphics To set up a triple display configuration you must connect a D Sub monitor using a DVI to D Sub adapter Triple display configurations are supported after you install motherboard drivers in OS Only dual display configurations are supported during the BIOS Setup or POST process RJ 45 LAN Port LAND The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate The following describes the states of the LAN port LEDs Connection Speed LED Activity LED Activity LED State Description State Description T Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring Green 100 Mbps data rate Off No data transmission or receiving is occurring LAN Port Off 10 Mbps data rate USB 3 0 2 0 Port The USB 3 0 port supports the USB 3 0 specification and is compatible to the USB 2 0 1 1 specification Use this port for USB devices Use this port for USB devices such as a USB keyboard mouse
20. Note Allows you to determine whether to limit CPUID maximum value Set this item to Disabled for Windows XP operating system set this item to Enabled for legacy operating system such as Windows NT4 0 Default Disabled Execute Disable Bit Note Enables or disables Intel Execute Disable Bit function This function may enhance protection for the computer reducing exposure to viruses and malicious buffer overflow attacks when working with its supporting software and system Default Enabled Intel Virtualization Technology Note Enables or disables Intel Virtualization Technology Virtualization enhanced by Intel Virtualization Technology will allow a platform to run multiple operating systems and applications in independent partitions With virtualization one computer system can function as multiple virtual systems Default Enabled Intel TXT LT Support Note Enables or disables Intel Trusted Execution Technology Intel TXT Intel Trusted Execution Technology provides a hardware based security foundation Default Disabled Dynamic Storage Accelerator Enables or disables Intel Dynamic Storage Accelerator When enabled the hard drive 1 0 performance will be adjusted according to hard drive load Default Disabled VT d Note Enables or disables Intel Virtualization Technology for Directed 1 0 Default Enabled Windows 8 Features Allows you to select the operating system to be installed Default Other OS CSM Su
21. USB printer USB flash drive and etc RJ 45 LAN Port LAN1 The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate The following describes the states of the LAN port LEDs Connection Speed LED Activity LED Activity LED State Description State Description Ez T Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring Green 100 Mbps data rate On No data transmission or receiving is occurring LAN Port Off 10 Mbps data rate Center Subwoofer Speaker Out Jack Orange Use this audio jack to connect center subwoofer speakers in a 5 1 7 1 channel audio configuration Rear Speaker Out Jack Black This jack can be used to connect front speakers in a 4 5 1 7 1 channel audio configuration Optical S PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital optical audio Before using this feature ensure that your audio system provides an optical digital audio in connector Line In Jack Blue The line in jack Use this audio jack for line in devices such as an optical drive walkman etc Line Out Jack Green The line out jack Use this audio jack for a headphone or 2 channel speaker This jack can be used to connect front speakers a 4 5 1 7 1 channel audio configuration Mic In Jack Pink The Mic in jack Microphones must be connected to this jack Hardware Installation 20
22. audio jacks be reconfigured to perform different functions via the audio software supported functions may vary based on hardware specification If you install a Side Speaker you need to retask other audio jack to be Side Speaker out Only microphones still MUST be connected to the default Mic in jack When removing the cable connected to a back panel connector first remove the cable from your device and then remove it from the motherboard When removing the cable pull it straight out from the connector Do not rock it side to side to prevent an electrical short inside the cable connector 21 Hardware Installation 1 7 Internal Connectors 1 ATX12V 8 F PANEL 2 9 SPDIF O 3 CPU FAN 10 USB30 4 SYS 11 USB 5 BAT 12 6 SATA3 0 1 2 31415 13 CLR CMOS 7 F AUDIO 14 CI e First make sure your devices compliant with the connectors you wish to connect Before installing the devices be sure to turn off the devices and your computer Unplug the power cord from the power outlet to prevent damage to the devices e After installing the device and before turning on the computer make sure the device cable has been securely attached to the connector on the motherboard i Read the following guidelines before connecting external devices Hardware Installation 22 1 2 12 2x2 12V Power Connector and 2x12 Main Power Connector Wit
23. co rs e Kazakhstan WEB address http www gigabyte kz You may go to the GIGABYTE website select your language in the language list on the top right corner of the website To submit a technical or non technical Sales Marketing que http The 80 stion please link to ggts gigabyte com tw n select your language to enter the system
24. configurations Options are 20 Upgrade 40 Upgrade 60 Upgrade 80 Upgrade 100 Upgrade Default Auto lt CPU Base Clock Allows you to manually set the CPU base clock in 0 01 MHz increments Default Auto Important It is highly recommended that the CPU frequency be set in accordance with the CPU specifications lt Host PCle Clock Frequency Allows you to manually set the host clock frequency which controls CPU PCle and memory frequencies in 0 01 MHz increments This item is configurable only when CPU Base Clock is set to Manual lt Processor Base Clock Gear Ratio CD Note Allows you to configure the Processor Base Clock by multiplying the Host PCle Clock Frequency by several preset host clock multipliers This item is configurable only when CPU Base Clock is set to Manual 7 Spread Spectrum Control Q Note Enables or disables CPU PCle Spread Spectrum Default Auto Host Clock Value This value is determined by multiplying the Host PCle Clock Frequency value by the Processor Base Clock Gear Ratio value lt Processor Graphics Clock Allows you to set the onboard graphics clock The adjustable range is from 400 MHz to 4000 MHz Default Auto 7 CPU Upgrade Note Allows you to set the CPU frequency Options may vary depending on the CPU being used Default Auto Only for GA Z97N WIFI Note This item is present only when you install a CPU that supports this feature For more information about Int
25. em carater prim rio MR 7946 ANRT 2013 Chile Ngan CCAH13LP0320T1 2092 DFRS08617 F 50 Connection and use of this communications AN CCAH13LP0340T7 China equipment is permitted by the NB CCAH13LP0360TO AN CMIIT ID 2013AJ0752 Nigerian Communications Commission BN CCAH13LP0380T6 NB CMIIT 1D 2013AJ0757 BN CMIIT 1D 2013AJ0754 See the latest safety and regulatory documents at GIGABYTE s website Copyright 2014 GIGA BYTE TECHNOLOGY CO LTD All rights reserved The trademarks mentioned in this manual are legally registered to their respective owners Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice No part of this manual may be reproduced copied translated transmitted or published in any form or by any means without GIGABYTE s prior written permission Documentation Classifications In order to assist in the use of this product GIGABYTE provides the following types of documentations For quick set up of the product read the Quick Installation Guide included with the product For detailed product information carefully read the User s Manual For product related information check on our website at http www gigabyte com Identifying Your Motherboard Revision The revision number on your motherboard looks like this REV X X For example
26. fail to boot after you make changes on the memory timings If this occurs please reset the board to default values by loading optimized defaults or clearing the CMOS values 41 BIOS Setup gt Advanced Voltage Settings GIGABYTE gt System Information BIOS Features Back M I T Aduanced Voltage Settings gt CPU Core Voltage Control DualBIOS Peripherals Copyright C 2014 American Me This sub menu allows you to set CPU chipset and memory voltages BIOS Setup 42 Pouer Management ST Mode English 3 Save amp Exit Q Flash gt PC Health Status GIGABYTE DualBIOS 2 a ON A 5 System Information BIOS Features Peripherals Power Management Save Exit o Back MBA ST Mode English Q Flash Reset Case Open Status Disabled Case Open CPU Vcore CPU URIN DRAM Voltage 3 30 5 120 CPU VAXG CPU Temperature System Temperature CPU Fan Speed 3183 RPM System Fan Speed 0 RPM Normal Normal j Reset Case Open Status Disabled Keeps or clears the record of previous chassis intrusion status Default Enabled Clears the record of previous chassis intrusion status and the Case Open field will show No at next boot Case Open Displays the detection status of the chassis intrusion detection device attached to the motherboard header If the system chassis cover is removed this field will show Yes otherwise it will show No To clear
27. in this section may differ from the exact settings for your motherboard The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version Configuring SATA Hard Drive s 58 C 1 UEFI RAID Configuration Only Windows 8 1 8 64 bit supports UEFI RAID configuration Step 1 In BIOS Setup go to BIOS Features and set Windows 8 Features to Windows 8 and CSM Support to Never Figure 2 Save the changes and exit BIOS Setup Limit CPUID Maximum Execute Disable Bit Intel Virtualization Technology Dynamic Storage Accelerator Windows 8 Features Administrator Password User Password System Mode state Secure Boot state Secure Boot Secure Boot Mode Step 2 GIGABYTE DualBIOS Setup Disabled Copyright 2014 finerican Megatrends Figure 2 Inc This option controls if CSM will be launched 11 Click Select Item Enter Dbl Click Select PU PD Change Opt F2 Smart Tweak Mode F5 Previous Values F Optimized Defaults F8 Q Flash F9 System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Select Screen After the system reboot enter BIOS Setup again Then enter the Peripherals Intel R Rapid Storage Technology sub menu Figure 3 Mode Audio Controller Intel Processor Graphics Intel Processor Graphics Memory Allocation DUMT Total Memory Size Intel R Rap
28. not remove or break motherboard S N Serial Number sticker or warranty sticker provided by your dealer These stickers are required for warranty validation Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components When connecting hardware components to the internal connectors on the motherboard make sure they are connected tightly and securely When handling the motherboard avoid touching any metal leads or connectors It is best to wear an electrostatic discharge ESD wrist strap when handling electronic components such as a motherboard CPU or memory If you do not have an ESD wrist strap keep your hands dry and first touch a metal object to eliminate static electricity Prior to installing the motherboard please have it on top of an antistatic pad or within an electrostatic shielding container Before unplugging the power supply cable from the motherboard make sure the power supply has been turned off Before turning on the power make sure the power supply voltage has been set according to the local voltage standard Before using the product please verify that all cables and power connectors of your hardware components are connected To prevent damage to the motherboard do not allow screws to come in contact with the motherboard circuit or its components Make sure there are no leftover screws or metal components placed on the motherboard
29. or within the computer casing Do not place the computer system on an uneven surface Do not place the computer system in a high temperature environment Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user If you are uncertain about any installation steps or have a problem related to the use of the product please consult a certified computer technician 9 Hardware Installation 1 2 Product Specifications 4 CPU Support for Intel Core i7 processors Intel Core i5 processors Intel Core i3 processors Intel Pentium processors Intel Celeron processors the LGA1150 package Go to GIGABYTE s website for the latest CPU support list 3 cache varies with CPU Chipset Intel Z97 H97 Express Chipset Memory 2xDDR3 DIMM sockets supporting up to 16 GB of system memory 2 Due to a Windows 32 bit operating system limitation when more than 4 GB of physical memory is installed the actual memory size displayed will be less than the size of the physical memory installed Dual channel memory architecture Support for DDR3 1600 1333 MHz memory modules Support for non ECC memory modules Support for Extreme Memory Profile memory modules Go to GIGABYTE s website for the latest supported memory speeds and memory modules Onboard Integrated Graphics Processor Y Graphics
30. overheated Auto lets the BIOS automatically configure this setting Default Auto gt CPU EIST Function Note Enables or disables Enhanced Intel Speed Step Technology EIST Depending on CPU loading Intel EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease average power consumption and heat production Auto lets the BIOS automatically configure this setting Default Auto gt Extreme Memory Profile Note 2 Allows the BIOS to read the SPD data on memory module s to enhance memory performance when enabled Disabled Disables this function Default Profile Uses Profile 1 settings Profile2 2 Uses Profile 2 settings Note 1 This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website Note 2 This item is present only when you install a CPU and a memory module that support this feature 39 BIOS Setup gt E System Memory Multiplier Allows you to set the system memory multiplier Auto sets memory multiplier according to memory SPD data Default Auto Memory Frequency MHz The first memory frequency value is the normal operating frequency the memory being used the second is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings Advanced Memory Settings GIGAB
31. setup menu esp Move the selection bar to select an configuration item on a menu lt Enter gt Execute command or enter a menu lt gt lt Page Up gt Increase the numeric value or make changes lt gt lt Page Down Decrease the numeric value or make changes lt F2 gt Switch to ST Mode or Startup Guide screen lt F5 gt Restore the previous BIOS settings for the current submenus lt F7 gt Load the Optimized BIOS default settings for the current submenus lt F8 gt Access the Q Flash utility lt F9 gt Display system information lt F10 gt Save all the changes and exit the BIOS Setup program lt F12 gt Capture the current screen as an image and save it to your USB drive lt Esc gt Main Menu Exit the BIOS Setup program Submenus Exit current submenu Only for GA Z97N WIFI BIOS Setup 94 BIOS Setup Menus B MIT Use this menu to configure the clock frequency and voltages of your CPU and memory etc Or check the system CPU temperatures voltages and fan speeds System Information Use this menu to configure the default language used by the BIOS and system time and date BIOS Features Use this menu to configure the device boot order and advanced features available on the CPU Peripherals Use this menu to configure all peripheral devices such as SATA USB integrated audio and integrated LAN etc Power Management Use this menu to configure all the power saving func
32. speed and chips be used for optimum performance Hardware Installation 16 1 4 2 Installing a Memory Before installing a memory module make sure to turn off the computer and unplug the power AN cord from the power outlet to prevent damage to the memory module DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs Be sure to install DDR3 DIMMs on this motherboard DDR3 DIMM ADDR3 memory module has a notch so it can only fit in one direction Follow the steps below to correctly install your memory modules in the memory sockets Step 1 Note the orientation of the memory module Spread the retaining clip at the right end of the memory socket Place the memory module on the socket As indicated in the picture on the left place your fingers on the top edge of the memory push down on the memory and insert it vertically into the memory socket Step 2 The clip at the right end of the socket will snap into place when the memory module is securely inserted 17 Hardware Installation 1 5 Installing an Expansion Card e Make sure the motherboard supports the expansion card Carefully read the manual that came with your expansion card Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to
33. surface of the installed CPU Place the cooler atop the CPU aligning the four push pins through the pin holes on the motherboard Push down on the push pins diagonally Step 5 After the installation check the back of the motherboard If the push pin is inserted as the picture above shows the installation is complete Male Push Pin Direction of the Arrow Sign on the Male 1827 Push Pin Female Push Pin Step 2 Before installing the cooler note the direction of the arrow sign lt on the male push pin Turning the push pin along the direction of arrow is to remove the cooler on the contrary is to install Step 4 You should hear a click when pushing down each push pin Check that the Male and Female push pins are joined closely Refer to your CPU cooler installation manual for instructions on installing the cooler Step 6 Finally attach the power connector of the CPU cooler to the CPU fan header CPU FAN on the motherboard Use extreme care when removing the CPU cooler because the thermal grease tape between the CPU cooler and CPU may adhere to the CPU Inadequately removing the CPU cooler may damage the CPU Hardware Installation 1 4 Installing the Memory Read the following guidelines before you begin to install the memory A e Make sure that the motherboard supports the memory It is recommended that memory of the same capacity brand speed and chips be us
34. the CPU socket Apply an even and thin layer of thermal grease on the surface of the CPU Do not turn on the computer if the CPU cooler is not installed otherwise overheating and damage of the CPU may occur e Set the CPU host frequency in accordance with the CPU specifications It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals If you wish to set the frequency beyond the standard specifications please do so according to your hardware specifications including the CPU graphics card memory hard drive etc 1 3 1 Installing the CPU Locate the alignment keys on the motherboard CPU socket and the notches on the CPU LGA1150 CPU Socket Alignment Key Alignment Key Pin One Corner of the CPU Socket LGA1150 CPU Triangle Pin One Marking on the CPU 13 Hardware Installation Follow the steps below to correctly install the CPU into the motherboard CPU socket Before installing the CPU make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU To protect the socket contacts do not remove the protective plastic cover unless the CPU is inserted into the CPU so
35. to return to the BIOS Setup Main Menu Exit Without Saving Press lt Enter gt on this item and select Yes This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS Select No or press lt Esc gt to return to the BIOS Setup Main Menu Load Optimized Defaults Press lt Enter gt on this item and select Yes to load the optimal BIOS default settings The BIOS defaults settings help the system to operate in optimum state Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values Boot Override Allows you to select a device to boot immediately Press lt Enter gt on the device you select and select Yes to confirm Your system will restart automatically and boot from that device Save Profiles This function allows you to save the current BIOS settings to a profile You can create up to 8 profiles and save as Setup Profile 1 Setup Profile 8 Press lt Enter gt to complete Or you can select Select File in HDD USB FDD to save the profile to your storage device Load Profiles If your system becomes unstable and you have loaded the BIOS default settings you can use this function to load the BIOS settings from a profile created before without the hassles of reconfiguring the BIOS settings First select the profile you wish to load and then press lt Enter gt to complete You can select Select File in HDD USB FDD to input the profile previously created from your storage device or load th
36. 2014 American Megatrends Intel Virtualization Technology Intel TXT LT Support Dynamic Storage Accelerator UT d Windows 8 Features Boot Mode Selection LAN PXE Boot Option ROM Storage Boot Option Control Other Device Priority Network stack Administrator Password System Mode state Setup Secure Boot state Disabled Copyright C 2014 American Megatrends Inc 7 Boot Option Priorities Specifies the overall boot order from the available devices Removable storage devices that support GPT format will be prefixed with string on the boot device list To boot from an operating system that supports GPT partitioning select the device prefixed with UEFI string Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64 bit select the optical drive that contains the Windows 7 64 bit installation disk and is prefixed with UEFI string 7 Bootup NumLock State Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST Default Enabled BIOS Setup DualBIOS DualBIOS 46 Specify the overall boot order from the available devices list Use keys to modify the order Default Devices ordered according to SATA port number Lowest first Select Screen fl Click Select Item Enter Dbl Click Select PU PD Change Opt F2 Smart Tweak Mode F5 Previous Values Optimized Defau
37. Controller Atheros GbE LAN Chip LAN 2 Enables or disables the Atheros GbE LAN function Default Enabled If you wish to install a 3rd party add in network card instead of using the onboard LAN set this item to Disabled 51 BIOS Setup gt SATA Configuration GIGABYTE DualBIOS Fa M MIT Systen Information BIOS Features Pouer Management Save amp Exit Back Peripherals SATA Configuration ST Mode English Q Flash Integrated SATA Controller Enabled AHCI Serial Port 0 Empty Softuare Preserve Unknoun Enabled Disabled Disabled Serial ATA Port 1 Empty Software Preserve Unknown Enabled Disabled Disabled Serial ATA Port 2 Empty Software Preserve Unknown Enabled Disabled Disabled Serial ATA Port 3 Empty Software Preserve Unknown Integrated SATA Controller Enables or disables the integrated SATA controllers Default Enabled SATA Mode Selection Enables or disables RAID for the SATA controllers integrated in the Chipset or configures the SATA controllers to AHCI mode IDE Configures the SATA controller to IDE mode RAID Enables RAID for the SATA controller gt AHCI Configures the SATA controllers to AHCI mode Advanced Host Controller Interface AHCI is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug Default v Serial ATA Port 0 1 2 3 415 Port 0 1 2 3 4 5 Enables or disabl
38. D Controller and click Next to load the driver and continue the OS installation Hide drivers that aren t compatible with this computer s hardware Browse Rescan 69 Configuring SATA Hard Drive s Rebuilding an Array Rebuilding is the process of restoring data to a hard drive from other drives in the array Rebuilding applies only to fault tolerant arrays such as RAID 1 RAID 5 or RAID 10 arrays The procedures below assume a new drive is added to replace a failed drive to rebuild a RAID 1 array Note The new drive must have equal or greater capacity than the old one Turn off your computer and replace the failed hard drive with a new one Restart your computer Enabling Automatic Rebuild Step 1 When the message Press Ctrl I to enter Configuration Utility appears press Ctrl lt I gt to enter the RAID Configuration Utility The following screen appears after you enter the RAID Configuration Utility MAIN MENU DEGRADED VOLUME DETECTED ah Hitachi HDS72105 JP1532FR3BWV7K 465 7GB Hitachi HDS72105 JP1532FR3ABMPK 465 7GB Step 2 Select the new hard drive to add into the array to be rebuilt and press lt Enter gt The following screen appears indicating that an automatic rebuild will be performed after you enter the operating system If you do not enable automatic rebuild on this stage you have to manually rebuild the array in the operating system see the next page
39. GA Z97N WIFI GA H97N WIFI User s Manual Rev 1001 12ME Z97NWIF 1001R Declaration of Conformit DECLARATION OF CONFORMITY G B T Technology Trading GMbH Per FCC Part 2 Section 2 1077 a Address Bullenkoppel 16 22047 Hamburg Germany Declare that the product Product Type Motherboard Product GA Z97N WIFI GA H97N WIFI conforms with the essential requirements of the following directives Responsible Party Name G B T INC U S A x 2004 108 EMC Directive Address 17358 Railroad Street Conduction amp Radiated Emissions EN 55022 2010 City of Industry CA 91748 DJ Immunity EN 55024 2010 X Power line harmonics EN 61000 3 2 2006 A2 2009 Phone Fax No 626 854 9338 626 854 9326 x Power line flicker EN 61000 3 3 2008 hereby declares that the product 4 2006 95 EC LVD Directive Product Name Motherboard X Safety EN60950 1 2006 A11 2009 A12 2011 Model Number GA Z97N WIFI GA H97N WIFI 04 1999 5 R amp TTE Directive Conforms to the following specifications X Technical Requirements EN 300 328 v1 8 1 EN 301 489 1 V1 9 2 EN 301 489 17 v2 2 1 FCC Part 15 Subpart B Section 15 107 a and Section 15 109 a Class Digital Device X 2011 65 EU RoHS Directive Supplementary Information X Restriction of use of certain This product does not contain any of the restricted TE ind This device complies with part 15 ofthe Rules Operation is substances in e
40. LECT DISKS box press lt Tab gt on the hard drive you want to use for the master drive and press lt Space gt on the hard drive you want to use for the recovery drive Make sure the recovery drive has equal or larger capacity than the master drive Then press lt Enter gt to confirm Figure 17 Intel 1115510 CREATE VOLUME MENU Name Volume0 RAID Level Recovery SELECT DISKS T4 Change TAB Next ESC ESC Previous Menu ENTER Select Figure 17 Step 4 Under Sync select Continuous or On Request Figure 18 When set to Continuous changes made to the data on the master drive will be automatically and continuously copied to the recovery drive when both hard drives are installed in the system On Request allows users to update data from the master drive to the recovery drive manually using the Intel Rapid Storage Technology utility in the operating system On Request also allows users to restore the master drive to a previous state CREATE VOLUME MENU Name Volume0 RAID Level Recovery Disks Select Disks Strip Size N A Capacity 0 0 GB NAME Continuous Create Volume HELP Select a sync option On Request volume is updated manually Continuous volume is updated automatically Figure 18 Step 5 Finally press lt Enter gt on the Create Volume item to begin creating the Recovery Volume and follow the on screen instructions to complete 67 Configuring SATA Hard
41. ORT 3 Non RAID Disk 465 7GB Enhanced In Sync HELP Press s to synchronize data from the cache device to the Accelerated Disk Volume Press r to remove the Disk Volume Acceleration IT IS RECOMMENDED THAT YOU PERFORM A SYNCHRONIZATION BEFORE REMOVING ACCELERATION Figure 20 Configuring SATA Hard Drive s 68 3 2 Installing the SATA RAID AHCI Driver and Operating System With the correct BIOS settings you are ready to install the operating system A Installing the Operating System As Windows 7 already include Intel SATA RAID AHCI driver you do not need to install separate RAID AHCI driver during the Windows installation process After the operating system is installed we recommend that you install all required drivers from the motherboard driver disk using Xpress Install to ensure system performance and compatibility To install Windows 8 1 8 refer to the steps below Step 1 Copy the IRST folder under BootDrv in the driver disk to your USB thumb drive Step 2 Boot from the Windows 8 1 8 setup disk and perform standard OS installation steps When the screen requesting you to load the driver appears select Browse Step 3 Insert the USB thumb drive and then browse to the location of the driver The locations of the drivers are as follows Windows 32 bit IRST 32Bit Windows 64 bit IRST 64Bit Step 4 When a screen as shown in Figure 1 appears select Intel R Desktop Workstation Server Express Chipset SATA RAI
42. REV 1 0 means the revision of the motherboard is 1 0 Check your motherboard revision before updating motherboard BIOS drivers or when looking for technical information Example v 428 NG ZU d E E j KAN Table of Contents COMES ons AA GA Z97N WIFI GA H97N WIFI Motherboard GA Z97N WIFI GA H97N WIFI Motherboard Block Diagram Chapter 1 Hardware Installation ccccccccssscsscsssscssesssecsssssscssecsscesessseesesaseeen 1 1 Installation Precautlons nnn nennen 12 Product ne metre eee 1 3 Installing the CPU and CPU Cooler 1 31 Installing the CPU etr rt 1 3 2 Installing the CPU 6 1 4 Installing the Memory 1 4 1 Dual Channel Memory Configuration 22 2 14 2 Installing a MEMON se 1 5 Installing an Expansion Card than 1 6 Back Panel inerte tr IRR S 2 1 Startup SCLC PEOR 2 2 The Main MONU a AS Mi 2 4 System Information 22 a es
43. YTE DualBIOS gt gt P gt a AS System Information BIOS Features Peripherals Pouer Management Save amp Exit Back M I T Aduanced Memory Settings ST Mode English Q Flash Extreme Memory Profile X M P Disabled Disabled Auto Auto Normal Auto Extreme Memory Profile X M P Note System Memory Multiplier Memory Frequency MHz The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu Memory Overclocking Profiles DiNote Allows you to set the memory frequency Options may vary depending on the memory being used Default Disabled Memory Boot Mode Provides memory detection and training methods Auto Lets the BIOS automatically configure this setting Default Enable Fast Boot Skip memory detection and training in some specific criteria for faster memory boot Disable Fast Boot Detect and train memory at every single boot Memory Enhancement Settings Provides three different memory performance enhancement settings Normal basic performance Enhanced Stability and Enhanced Performance Default Normal Memory Timing Mode Manual and Advanced Manual allows the Channel Interleaving Rank Interleaving and memory timing settings below to be configurable Options are Auto default Manual Advanced Manual Only for GA Z97N WIFI Note This item is present only when you install a CPU and a memory module that support this feature BIOS Setup 40
44. al or greater capacity than the master drive e A recovery volume be created with two hard drives only recovery volume and a RAID array cannot co exist in the system at the same time that is if you have already created a recovery volume you are unable to create a RAID array By default only the master drive can be viewed in the operating system the recovery drive is hidden Step 1 Select Create RAID Volume in MAIN MENU and press lt Enter gt Figure 15 mi AIN PES TAY VIEN MAIN MENU 1 Create Volume 4 Recovery Volume Options 2 Delete RAID Volume 5 Acceleration Options 3 Reset Disks to Non RAID 6 Exit DISK VOLUME INFORMATION RAID Volumes None defined Physical Disks IE Drive Model Serial Size Type Status Vol ID 1 Hitachi HDS72105 JP1532FR3BWV7K 465 7GB 2 Hitachi HDS72105 JP1532ER046M2K 465 7GB LG Alay ase Exit elect ECSC EXIL Figure 15 Step 2 After entering the volume name select Recovery under the RAID Level item and press lt Enter gt Figure 16 Intel CREATE VOLUME MENU Name Volume0 RAID Level Disks Select Disks Strip Size N A Capacity 465 7 GB Sync Continuous Create Volume HELP Recovery Copies data between a master and a recovery disk TAB Next ESC Previous Menu Figure 16 Configuring SATA Hard Drive s 66 Step 3 Press Enter under the Select Disks item In the SE
45. assword and then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt You must enter the administrator password or user password at system startup and when entering BIOS Setup However the user password only allows you to make changes to certain BIOS settings but not all To cancel the password press lt Enter gt on the password item and when requested for the password enter the correct one first When prompted for a new password press lt Enter gt without entering any password Press lt Enter gt again when prompted to confirm 49 BIOS Setup 2 6 Peripherals DualBIOS a Ca BIOS Features Power Management Save amp Exit o ST Mode English Q Flash System Information Initial Display Output PCIe 1 Enabled Smart Auto Enabled Enabled 64M MAK Disabled Enabled Enabled Disabled USB Storage Devices Auto Disabled Enabled lt Initial Display Output Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard graphics gt IGFX Sets the onboard graphics as the first display PCle 1 Slot Sets the graphics card on the PCIEX16 slot as the first display Default PCHLAN Controller Intel GbE LAN Chip LAN1 Enables or disables the Intel GbE LAN function Default Enabled If you wish to install a 3rd party add in network card instead of using the onboard LAN s
46. ating system to boot Auto Enables legacy option ROM only EFI Driver Enables EFI option ROM Default This item is configurable only when Fast Boot is set to Enabled or Ultra Fast USB Support Disabled All USB devices are disabled before the OS boot process completes gt gt Full Initial All USB devices are functional in the operating system and during the POST Partial Initial Part of the USB devices are disabled before the OS boot process completes Default This item is configurable only when Fast Boot is set to Enabled This item is disabled when Fast Boot is set to Ultra Fast PS2 Devices Support Disabled All PS 2 devices are disabled before the OS boot process completes Enabled All PS 2 devices are functional in the operating system and during the POST Default This item is configurable only when Fast Boot is set to Enabled This item is disabled when Fast Boot is set to Ultra Fast NetWork Stack Driver Support Disabled Disables booting from the network Default Enabled Enables booting from the network This item is configurable only when Fast Boot is set to Enabled or Ultra Fast Next Boot After AC Power Loss Normal Boot Enables normal bootup upon the return of the AC power Default Fast Boot Keeps the Fast Boot settings upon the return of the AC power This item is configurable only when Fast Boot is set to Enabled or Ultra Fast 47 BIOS Setup Limit CPUID Maximum
47. cket Save the cover properly and replace it if the CPU is removed D vere i 11 INTEL CONFIDENTIAL QD4C ES 2 68GH2 ISA Gently press the CPU socket lever handle down Hold the CPU with your thumb and index fingers and away from the socket with your finger Then Align the CPU pin one marking triangle with the completely lift the CPU socket lever and the metal pin one corner of the CPU socket or you may align load plate plastic cover will be lifted as well the CPU notches with the socket alignment keys and gently insert the CPU into position e Step 3 Once the CPU is properly inserted carefully Finally secure the lever under its retention tab to replace the load plate When replacing the load complete the installation of the CPU plate make sure the front end of the load plate is under the shoulder screw Then press the CPU socket lever The protective plastic cover may pop off from the load plate during the process of engaging the lever Remove the cover Save the cover properly and always replace it when the CPU is not installed py NOTE 2 Hold the CPU socket lever by the handle not the lever base portion Hardware Installation 14 1 3 2 Installing the CPU Cooler Follow the steps below to correctly install the CPU cooler on the motherboard The following procedure uses Intel boxed cooler as the example cooler TAY Step 1 Apply an even and thin layer of thermal grease on the
48. ction administration for recycling f you need further assistance in recycling reusing in your end of life product you may contact us at the Customer Care number listed in your product s user s manual and we will be glad to help you with your effort Finally we suggest that you practice other environmentally friendly actions by understanding and using the energy saving features of this product where applicable recycling the inner and outer packaging including shipping containers this product was delivered in and by disposing of or recycling used batteries properly With your help we can reduce the amount of natural resources needed to produce electrical and electronic equipment minimize the use of landfills for the disposal of end of life products and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly Appendix 14 Notice U S A Only This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by on
49. d are 4 pin Most fan headers possess a foolproof insertion design When connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire The speed control function requires the use of a fan with fan speed control design For optimum heat dissipation it is recommended that a system fan be installed inside the chassis C3 Bec CPU FAN Pin No Definition 1 GND 1 2 12V CPU FAN 3 Sense 4 Speed Control __ SYS 1 Pin No Definition SYS_FAN 1 GND GE 8 2 Speed Control a 3 Sense 4 5V Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating Overheating may result in damage to the CPU or the system may hang These fan headers are not configuration jumper blocks Do not place a jumper cap on the headers 5 BAT Battery The battery provides power to keep the values such as BIOS configurations date and time information in the CMOS when the computer is tumed off Replace the battery when the battery voltage drops to a low level or the CMOS values may not be accurate or may be lost
50. e mainly consists of power switch reset switch hard drive activity LED and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly Hardware Installation 26 9 SPDIF O S PDIF Out Header This header supports digital S PDIF Out and connects a S PDIF digital audio cable provided by expansion cards for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards For example some graphics cards may require you to use a S PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time For information about connecting the S PDIF digital audio cable carefully read the manual for your expansion card EB 4 Pin No Definition ag B 1 SPDIFO E 2 GND DSc 10 F_USB30 USB 3 0 2 0 Header The header conforms to USB 3 0 2 0 specification and can provide two USB ports For purchasing the optional 3 5 front panel that provides two USB 3 0
51. e or more of the following measures e Reorient or relocate the receiving antenna ncrease the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult a dealer or experienced TV radio technician for help Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits Neither the Dealer nor the Manufacturer are responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment Unauthorized changes or modifications could void the user s authority to operate the equipment CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment Canada Industry Canada This device complies with RSS210 of Industry Canada Cet appareil se conforme 55210 de Canada d Industrie Caution When using IEEE 802 11a wireless LAN this product is restricted to indoor use due to its operation in the 5 15 to 5 25 GHz frequency range Industry Canada requires this product to be used indoors for the frequency range of 5 15 GHz to 5 25 GHz to reduce the potential for harmful interference to co channel mobile satellite systems High power radar is allocated as the primary user of the 5 25 to 5 35 GHz and 5 65 to 5 85 GH
52. e profile automatically created by the BIOS such as reverting the BIOS settings to the last settings that worked properly last known good record BIOS Setup 56 Chapter 3 Configuring SATA Hard Drive s RAID Levels RAID 0 RAID 1 RAID 5 RAID 10 Minimum Number of Hard gt 2 2 gt 3 gt 4 Drives Array Capacity Number of hard Size of the smallest Number of hard Number of hard drives Size ofthe drive drives 1 Size of drives 2 Size of the smallest drive the smallest drive smallest drive Fault Tolerance No Yes Yes Yes To configure SATA hard drive s follow the steps below A Install SATA hard drive s in your computer B Configure SATA controller mode in BIOS Setup C Configure a RAID array in RAID BIOS ee 1 D Install the SATA RAID AHCI driver and operating system Not 2 Before you begin Please prepare e Atleast two SATA hard drives to ensure optimal performance it is recommended that you use two hard drives with identical model and capacity If you do not want to create RAID you may prepare only one hard drive e Windows setup disk e Motherboard driver disk AUSB thumb drive 3 1 Configuring SATA Controllers A Installing SATA hard drive s in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard Then connect the power connector from your power supply t
53. ections available depend on the number of the hard drives being installed Press Enter to proceed CREATE VOLUME MENU Name Volume0 RAID Level Disks Select Disks Strip Size 16KB Capacity 931 5 GB Sync N A Create Volume HELP RAID 0 Stripes data performance ESC Previous Men Figure 11 Step 4 Under Disks item select the hard drives to be included in the RAID array If only two hard drives are installed they will be automatically assigned to the array Set the stripe block size Figure 12 if necessary The stripe block size can be set from 4 KB to 128 KB Once you have selected the stripe block size press lt Enter gt Inte Opt CREATE VOLUME MENU Name Volume0 RAID Level RAID0 Stripe Disks Select Disks Strip Size 16KB Capacity 931 5 GB Sync N A Create Volume HELP The following are typical values RAIDO 128KB RAIDIO 64KB RAIDS 64KB T4 Change TAB Next ESC Previous Menu ENTER Select Figure 12 Configuring SATA Hard Drive s 64 Step 5 Enter the array capacity and press lt Enter gt Finally press lt Enter gt on the Create Volume item to begin creating the RAID array When prompted to confirm whether to create this volume press lt gt to confirm or lt N gt to cancel Figure 13 CREATE VOLUME MENU Name Volume0 RAID Level RAID0 Stripe Disks Select Disks Strip Size 128 MB Capacity 931 5 GB WARNING ALL
54. ed Go to GIGABYTE s website for the latest supported memory speeds and memory modules Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage e Memory modules have a foolproof design A memory module can be installed in only one direction If you are unable to insert the memory switch the direction 1 4 1 Dual Channel Memory Configuration This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology After the memory is installed the BIOS will automatically detect the specifications and capacity of the memory Enabling Dual Channel memory mode will double the original memory bandwidth The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following bp Channel A DDR3 1 Channel DDR3 2 CE DDR3 1 DDR3 2 lll Due to CPU limitations read the following guidelines before installing the memory in Dual Channel mode 1 Dual Channel mode cannot be enabled if only one DDR3 memory module is installed 2 When enabling Dual Channel mode with two memory modules it is recommended that memory of the same capacity brand
55. el CPUs unique features please visit Intel s website 37 BIOS Setup CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU The adjustable range is dependent on the CPU being installed lt Frequency Displays the current operating CPU frequency gt Advanced CPU Core Settings GIGABYTE DualBIOS SD s 1 e _ c Sai A Systen Information BIOS Features Peripherals Power Management Save amp Exit o Back M I T Aduanced Frequency Settings Aduanced CPU Core Settings ST Mode English Q Flash CPU Clock Ratio 35 Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto 7 CPU Clock Ratio CPU Frequency The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu c K OC Note Allows for increased performance by using certain CPUs Default Auto CPU PLL Selection Allows you to set the CPU PLL Auto lets the BIOS automatically configure this setting Default Auto Filter PLL Level Allows you to set the Filter PLL Auto lets the BIOS automatically configure this setting Default Auto lt Uncore Ratio Allows you to set the CPU Uncore ratio The adjustable range is dependent on the CPU being used lt Uncore Frequency Displays the current CPU Uncore frequency lt Intel R Turbo Boost Technology Note Allows you to determine whether to enable the Intel CPU Turb
56. es each SATA port Default Enabled Hot plug Enables or disable the hot plug capability for each SATA port Default Disabled lt External SATA Enables or disables support for external SATA devices Default Disabled BIOS Setup 52 Super 10 Configuration This section provides information on the super I O chip and allows you to configure the serial port Serial Port A Enables or disables the onboard serial port Default Enabled Intel R Smart Connect Technology ISCT Configuration Enables or disables Intel Smart Connect Technology Default Disabled Intel R Ethernet Network Connection LAN1 This sub menu provides information on LAN configuration and related configuration options 53 BIOS Setup 2 7 Power Management GIGABYTE S e 5 gt at MM a A MIT System Information BIOS Features DualBIOS COR OR Peripherals Save amp Exit o ST Mode English Q Flash Power Loading Auto Disabled Enabled Instant Enabled Always Off Disabled Disabled Disabled Disabled Power Loading Enables or disables dummy load When the power supply is at low load a self protection will activate causing it to shutdown or fail If this occurs please set to Enabled Auto lets the BIOS automatically configure this setting Default Auto Resume by Alarm Determines whether to power on the system at a desired time Default Disabled If enabled set the date and time as following
57. et this item to Disabled 7 XHCIMode Allows you to determine the operating mode for the xHCI controller in OS Smart Auto This mode is available only when the BIOS supports the controller in the pre boot environment This mode is similar to Auto but it adds the capability to route the ports to or EHCI according to setting used in previous boots for non G3 boot in the pre boot environment This allows the use of USB 3 0 devices prior to OS boot controller enabling and rerouting should follow the steps in Auto when previous boot routs ports to EHCI Note This is the recommended mode when BIOS has pre boot support Default Auto BIOS routes the sharable ports to EHCI controller Then it uses ACPI protocols to provide an option to enable the controller and reroute the sharable ports Note This is the recommended mode when BIOS does NOT have xHCl pre boot support Enabled All shared ports are eventually routed to the controller during the BIOS boot process If BIOS does not have pre boot support for the XHCI controller it should initially route the sharable ports to the EHCI controller and then prior to OS boot it should route the ports to controller Note OS has to provide support for the xHCI controller in this mode If the OS does not provide support all sharable ports won t work Disabled The USB 3 0 ports are routed to the EHCI controller and the xHCI controller
58. for more details 1 Create RAID Volume Recovery Volume Options 2 Delete RAID Volume 5 Acceleration Options 3 Reset Disks to Non RAID Exit DISK VOLUME INFORMATION RAID Volumes ID Name Level Strip Size Status Bootable 0 Volume0 RAID1 Mirror N A 465 7GB Yes Physical Devices ID Devices Model Serial Size Type Status Vol ID 0 Hitachi HDS72105 JP1532FR3BWV7K 465 7GB 1 Hitachi HDS72105 HD1529EP2ABRMDE 1657102 Configuring SATA Hard Drive s 70 Performing the Rebuild in the Operating System While in the operating system make sure the chipset driver has been installed from the motherboard driver disk Then launch the Intel Rapid Storage Technology utility from the desktop 2 intel An array disk has failed and you need to rebuild the volume to maintain redundancy and keep your data protected Select the disk you want to rebuild the volume to SATA disk on Controller 0 Port 3 466 GB WARNING Completing this action will permanently delete existing data on the selected disk Back up data before continuing You can continue using other applications during this time More help Step 2 Select new drive to rebuild the RAID and click Rebuild Step 1 Go to the Manage menu and click Rebuild to another disk in Manage Volume The Status item on the left of the screen displays Step 3 the rebuild progress After the RAID 1 v
59. h the use ofthe power connector the power supply can supply enough stable power to all the components on the motherboard Before connecting the power connector first make sure the power supply is turned off and all devices are properly installed The power connector possesses a foolproof design Connect the power supply cable to the power connector in the correct orientation The 12V power connector mainly supplies power to the CPU If the 12V power connector is not connected the computer will not start 12V Pin No Definition 1 GND 3 4 2 GND i 2 3 12V i 12V 4 a ATX Pin No Definition Pin No Definition 1 3 3V 13 3 3V 2 3 3V 14 12V 3 GND 15 GND 4 5V 16 5 soft On Off 5 GND 17 GND 6 5V 18 GND 7 GND 19 GND 8 Power Good 20 5 9 5VSB stand by 5 21 5V 10 12V 22 5V 11 12V Only for 2x12 pin 23 5 Only for 2x12 pin ATX 12 3 3V Only for 2x12 pin 24 GND Only for 2x12 pin ATX ATX ATX 22 Hardware Installation 3 4 CPU FAN SYS FAN Fan Headers The fan headers on this motherboar
60. hnology Create RAID Volume Select RAID Level Volumel QM Select Disks SATA 0 0 Hitachi HDS721050CLA660 JP1532FR3BK SATA 0 1 Hitachi HDS721050CLA660 JP1532ER04E RALDO Str ipe Strip Size Capacity 3 Select Screen fl Click Select Item Enter Dbl Click Select b Create Volume PU PD Change Opt F2 Smart Tweak Mode F5 Previous Values Optimized Defaults F8 Q Flash F9 System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Copyright C 2014 American Megatrends Inc Figure 4 Step 4 Under Select Disks item select the hard drives to be included in the RAID array Press the Space key the hard drives to be selected selected hard drives are marked with X Then set the stripe block size Figure 5 The stripe block size can be set from 4 KB to 128 KB Once you have selected the stripe block size set the volume capacity DualBIOS Back Perivherals Intel R Rapid Storage Technology Create RAID Volume Strip size help Name Volumel RAID Level Strip Size Select Disks SATA 0 0 Hitachi HDS721050CLA660 JP1532FR3BK SATA 0 1 Hitachi HDS721050CLA660 JP1532ER04E Capacity MB Select Screen 11 Click Select Item ones a m Enter Dbl Click Select b Create Volume PU PD Change Opt Smart Tweak Mode Previous Values Optimized Defaults Q Flash
61. id Start Technology Legacy USB Support Hand off EHCI Hand off USB Storaye Devices SanDisk Cruzer Pop 1 26 Two Layer KUM Switch OnBoard LAN Controller b SATA Configuration b Super I0 Configuration gt Intel R Smart Connect Technology Intelth Ethernet Network CONNECTION DualBIOS 1211 9 44 99 10 25 JA gt Intel R Rapid Storage Technology Copyright C 2014 American Megatrends Inc Figure 3 This formset allows the user to manage RAID volumes on the Intel R RAID Control ler Select Screen 11 Click Select Item Enter Dbl Click Select PU PD Change Opt F2 Smart Tweak Mode F5 Previous Values Optimized Defaults F8 Q Flash F9 System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit 59 Configuring SATA Hard Drive s Step 3 On the Intel R Rapid Storage Technology menu press lt Enter gt on Create RAID Volume to enter the Create RAID Volume screen Enter a volume name with 1 16 letters letters cannot be special characters under the Name item and press lt Enter gt Then select a RAID level Figure 4 RAID levels supported include RAID 0 RAID 1 RAID 10 and RAID 5 the selections available depend on the number of the hard drives being installed Next use the down arrow key to move to Select Disks GIGABYTE DualBIOS SPA Back Peripherals Intel R Rapid Storage Tec
62. is turned off All USB 3 0 devices function as High Speed devices regardless of xHCI software support availability BIOS Setup 50 Audio Controller Enables or disables the onboard audio function Default Enabled If you wish to install a 3rd party add in audio card instead of using the onboard audio set this item to Disabled Intel Processor Graphics Enables or disables the onboard graphics function Default Enabled Intel Processor Graphics Memory Allocation Allows you to set the onboard graphics memory size Options are 32M 1024M Default 64M DVMT Total Memory Size Allows you to allocate the DVMT memory size of the onboard graphics Options are 128M 256M MAX Default MAX Intel R Rapid Start Technology Enables or disables Intel Rapid Start Technology Default Disabled Legacy USB Support Allows USB keyboard mouse to be used in MS DOS Default Enabled XHCI Hand off Determines whether to enable XHCI Hand off feature for an operating system without XHCI Hand off support Default Enabled EHCI Hand off Determines whether to enable EHCI Hand off feature for an operating system without EHCI Hand off support Default Disabled USB Storage Devices Displays a list of connected USB mass storage devices This item appears only when a USB storage device is installed Two Layer KVM Switch Set to Enabled to ensure proper device functionality when chaining two KVM switches Default Disabled Onboard LAN
63. lectronic equipment substances listed in Annex Il in concentrations and applications banned by the directive subject to the following two conditions 1 This device may not cause harmful and 2 this device must accept any inference received CE marking gt including that may cause undesired operation Representative Person s Name ERIC LU Signature Eric Lu Signature Timmy Huang Date May 2 2014 Stamp Date 2 2014 Name Timmy Huang Wireless Module Country Approvals European Union Philippines United Arab Emirates ESD 1307219C ER0105789 13 Qatar Ukraine ICTQATAR RT 2013 R 3412 10094 001216 13 NB 10094 001213 13 United States FCC PD97260HU Canada IC 1000M 7260H Algeria India 300 IR AGR PC ARPT 2013 AN NR ETA 546 A Australia amp New Zealand NB NR ETA 547 Uruguay BN NR ETA 548 011 13 URSEC 210 FR 2013 N232 Japan Singapore R 003 130044 Complies with Brazil 0130020003 IDA Standards abs NATEL 5 15 5 35GHz indoor use only Ag ncia Nacional Telecomunica es Jordan South Korea 0640 13 2198 TRC LPD 2013 113 Mexico KCC CRM INT 7260HMW AN RCPIN7213 0646 AN KCC CRM INT 7260HMWAN NB RCPIN7213 0639 NB KCC CRM INT 7260HMWNB 01 07898355950261 BN RCPIN7213 0645 BN KCC CRM INT 7260HMWBN Este equipamento opera em car ter secundario isto 6 nao tem ee Tawan sistemas operando
64. lts F8 Q Flash F9 System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Allows you to setup a user password that will be required upon system boot To configure the password you will be asked to enter then re enter the password Note User level password protection restrictions limit access to certain BIOS features Select Screen fl Click Select Item Enter Dbl Click Select PU PD Change Opt F2 Smart Tweak Mode F5 Previous Values Optimized Defaults F8 Q Flash F9 System Information F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Security Option Specifies whether a password is required every time the system boots or only when you enter BIOS Setup After configuring this item set the password s under the Administrator Password User Password item gt gt Setup A password is only required for entering the BIOS Setup program System A password is required for booting the system and for entering the BIOS Setup program Default Full Screen LOGO Show Allows you to determine whether to display the GIGABYTE Logo at system startup Disabled skips the GIGABYTE Logo when the system starts up Default Enabled Fast Boot Enables or disables Fast Boot to shorten the OS boot process Ultra Fast provides the fastest bootup speed Default Disabled VGA Support Allows you to select which type of oper
65. ments Regulatory Notices This document must not be copied without our written permission and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose Contravention will be prosecuted We believe that the information contained herein was accurate in all respects at the time of printing GIGABYTE cannot however assume any responsibility for errors or omissions in this text Also note that the information in this document is subject to change without notice and should not be construed as a commitment by GIGABYTE Our Commitment to Preserving the Environment In addition to high efficiency performance all GIGABYTE motherboards fulfill European Union regulations for RoHS Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment WEEE Waste Electrical and Electronic Equipment environmental directives as well as most major worldwide safety requirements To prevent releases of harmful substances into the environment and to maximize the use of our natural resources GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your end of life product Restriction of Hazardous Substances 5 Directive Statement GIGABYTE products have not intended to add and safe from hazardous substances Hg Cr 6 PBDE and PBB The parts and components have been carefully selected to meet RoHS requirement Moreover
66. ndard and are compatible with SATA 3Gb s and SATA 1 5Gb s standard Each SATA connector supports a single SATA device The Intel Chipset supports RAID 0 RAID 1 RAID 5 and RAID 10 Refer to Chapter 3 Configuring SATA Hard Drive s for instructions on configuring a RAID array BEBE 8 Pin No Definition SATA3 1 GND TXP TXN GND RXN RXP GND No Ro gt 111 2060 TED 8 7 ut are to be used the total number of hard drives must be an even number ARAID 5 configuration requires at least three hard drives The total number of hard drives does not have to be an even number ARAID 10 configuration requires four hard drives To enable hot plugging for the SATA ports refer to Chapter 2 BIOS Setup Peripherals SATA Configuration for more information ER ARAID 0 or RAID 1 configuration requires at least two hard drives If more than two hard drives F AUDIO Front Panel Audio Header The front panel audio header supports Intel High Definition audio HD and AC 97 audio You may connect your chassis front panel audio module to this header Make sure the wire assignments of the module connector match the pin assignments of the motherboard header
67. o Boost technology Auto lets the BIOS automatically configure this setting Default Auto 7 Turbo Ratio 1 Core Active 4 Core Active Note Allows you to set the CPU Turbo ratios for different number of active cores Auto sets the CPU Turbo ratios according to the CPU specifications Default Auto Note This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website BIOS Setup 38 7 Turbo Power Limit Watts Allows you to set a power limit for CPU Turbo mode When the CPU power consumption exceeds the specified power limit the CPU will automatically reduce the core frequency in order to reduce the power Auto sets the power limit according to the CPU specifications Default Auto Core Current Limit Amps Allows you to set a current limit for CPU Turbo mode When the CPU current exceeds the specified current limit the CPU will automatically reduce the core frequency in order to reduce the current Auto sets the power limit according to the CPU specifications Default Auto No of CPU Cores Enabled Note 1 Allows you to select the number of CPU cores to enable in an Intel multi core CPU the number of CPU cores may vary by CPU Auto lets the BIOS automatically configure this setting Default Auto lt Hyper Threading Technology Note 1 Allows you to determine whether to enable multi threading technology when using an Intel
68. o the hard drive Note 1 Skip this step if you do not want to create RAID array on the SATA controller Note 2 Required when the SATA controller is set to AHCI or RAID mode 57 Configuring SATA Hard Drive s Configuring SATA controller mode BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup Step 1 Turn on your computer and press Delete to enter BIOS Setup during the POST Power On Self Test Go to Peripherals SATA Configuration make sure Integrated SATA Controller is enabled To create RAID set SATA Mode Selection to RAID Figure 1 If you do not want to create RAID set this item to IDE or AHCI GIGABYTE DualBIOS A 2 re No AS AS MIT System Information BIOS Features Power Management Save amp Exit o Back Peripherals SATA Configuration ST Mode English Q Flash Enabled SATA Mode Selection RAID Serial Port 0 UDC UD800JD 22 80 0GB Softuare Preserve SUPPORTED Enabled Disabled Disabled Serial ATA Port 1 WDC WD800JD 22 80 0GB Softuare Preserve SUPPORTED Enabled Disabled Disabled Serial ATA Port 2 Empty Software Preserve Unknown Enabled Disabled Disabled Serial ATA Port 3 Empty Software Preserve Unknown Figure 1 Step 2 If you want to configure UEFI RAID follow the steps in C 1 To enter the legacy RAID ROM save the settings and exit BIOS Setup Refer to C 2 for more information The BIOS Setup menus described
69. olume rebuilding the Status will display as Normal 71 Configuring SATA Hard Drive s Restoring the Master Drive to a Previous State for Recovery Volume only When two hard drives are set to Recovery Volume in Update on Request mode you can restore the master drive data to the last backup state when needed For example in case the master drive detects a virus you can restore the recovery drive data to the master drive Step 1 Select 4 Recovery Volume Options in the MAIN MENU of the Intel RAID Configuration Utility On the RECOVERY VOLUMES OPTIONS menu select Enable Only Recovery Disk to show the recovery drive in the operating system Follow the on screen instructions to complete and exit the RAID Configuration Utility Intel R Rapid Storage Technology Option ROM 13 0 0 2075 Copyright C Intel Corporation All Rights Reserved RECOVERY VOLUME OPTIONS 1 Enable Only Recovery Disk 2 Enable Only Master Disk Select a Recovery volume to do the operation T4 Up Down SPACE Selects ENTER Done 1 4 select ESC Previous Menu ENTER Select Are you sure you want to copy all the data from the recovery disk to the master disk WARNING Completing this action will override any master disk changes since the last update You can continue using other applications during this time More help Step 3 Click Yes to begin the data recovery Step 2 Go to the Manage menu of the Intel Ra
70. ower supply providing at least 1A on the 5VSB lead Disabled Disables this function Default Any Key Press any key to turn on the system Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system Password Set a password with 1 5 characters to turn on the system Power On Password Set the password when Power By Keyboard is set to Password Press lt Enter gt on this item and set a password with up to 5 characters and then press lt Enter gt to accept To turn on the system enter the password and press lt Enter gt Note To cancel the password press lt Enter gt on this item When prompted for the password press lt Enter gt again without entering the password to clear the password settings Power On By Mouse Allows the system to be turned on by a PS 2 mouse wake up event Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead Disabled Disables this function Default Move Move the mouse to turn on the system Double Click Double click on left button on the mouse to turn on the system ErP Determines whether to let the system consume least power in S5 shutdown state Default Disabled Note When this item is set to Enabled the following functions will become unavailable PME event wake up power on by mouse power on by keyboard and wake on LAN Platform Power Management Enables or disables the Active State Power Management f
71. pid Storage Technology utility and click Recover data in Manage Volume Step 4 The Status item on the left ofthe screen displays After the recovery volume is completed the Status the rebuild progress will display as Normal Configuring SATA Hard Drive s 72 Chapter 4 Appendix Drivers Installation Before installing the drivers first install the operating system The following instructions use ER Windows 8 1 as the example operating system e After installing the operating system insert the motherboard driver disk into your optical drive Click on the message Tap to choose what happens with this disc on the top right corner of the screen and select Run Run exe Or go to My Computer double click the optical drive and execute the Run exe program Xpress Install will automatically scan your system and then list all of the drivers that are recommended to install You can click the Xpress Install button and Xpress Install will install all of the selected drivers Or click the arrow E icon to individually install the drivers you need o GIGABYTE Xpress Install We recommend that you install the drivers listed below for your motherboard Please click Xpress Install to install all the Chipset drivers automatically rivers Click the ex button on the right of an application to install it For more software information please visit GIGABYTE s website 73 Appendix Regulatory State
72. positive and negative pins before connecting the cables 10 9 NC Power Switch bng PW RES PLED HD Hard Drive PLED HD PLED Power LED Yellow System Status LED Connects to the power status indicator on the chassis front panel The LED S0 On is on when the system is operating The LED is off when the system is in S3 S3 S4 S5 Off 54 sleep state or powered off 55 PW Power Switch Red Connects to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch refer to Chapter 2 BIOS Setup Power Management for more information e HD Hard Drive Activity LED Blue Connects to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data RES Reset Switch Green Connects to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart NC Purple No connection The front panel design may differ by chassis A front panel modul
73. pport Enables or disables UEFI CSM Compatibility Support Module to support a legacy PC boot process Always Enables UEFI CSM Default Never Disables UEFI CSM and supports UEFI BIOS boot process only This item is configurable only when Windows 8 Features is set to Windows 8 Boot Mode Selection Allows you to select which type of operating system to boot and Legacy Allows booting from operating systems that support legacy option ROM or UEFI option ROM Default Legacy Only Allows booting from operating systems that only support legacy Option ROM UEFI Only Allows booting from operating systems that only support UEFI Option ROM This item is configurable only when CSM Support is set to Always LAN PXE Boot Option ROM Allows you to select whether to enable the legacy option ROM for the LAN controller Default Disabled This item is configurable only when CSM Support is set to Always Storage Boot Option Control Allows you to select whether to enable the or legacy option ROM for the storage device controller gt gt Disabled Disables option ROM Legacy only Enables legacy option ROM only Default gt gt UEFI only Enables UEFI option ROM only Legacy First Enables legacy option ROM first UEFI First Enables UEFI option ROM first This item is configurable only when CSM Support is set to Always Note This item is present only when you install a CPU that supports this feature Fo
74. prevent hardware damage t Read the following guidelines before you begin to install an expansion card cm o PCI Express x16 Slot Follow the steps below to correctly install your expansion card in the expansion slot Locate an expansion slot that supports your card Remove the metal slot cover from the chassis back panel Align the card with the slot and press down on the card until it is fully seated in the slot Make sure the metal contacts on the card are completely inserted into the slot Secure the card s metal bracket to the chassis back panel with a screw After installing all expansion cards replace the chassis cover s Turn on your computer If necessary go to BIOS Setup to make any required BIOS changes for your expansion 5 7 Install the driver provided with the expansion card in your operating system Dx BB Example Installing and Removing PCI Express Graphics Card Installing a Graphics Card Gently push down on the top edge of the card until vol gt R it is fully inserted into the PCI Express slot Make sure the card is securely seated in the slot and does not rock e Removing the Card Gently push back on the lever on the slot and then lift the card straight o
75. r 1 for how to clear the CMOS values 31 BIOS Setup 2 1 Startup Screen The following startup Logo screen will appear when the computer boots GIGABYTE Function Keys Function Keys lt DEL gt BIOS SETUP Q FLASH Press the lt Delete gt key to enter BIOS Setup or to access the Q Flash utility in BIOS Setup lt F9 gt SYSTEM INFORMATION Press the lt F9 gt key to display your system information lt F12 gt BOOT MENU Boot Menu allows you to set the first boot device without entering BIOS Setup In Boot Menu use the up arrow key lt T gt or the down arrow key lt 4 gt to select the first boot device then press lt Enter gt to accept The system will boot from the device immediately Note The setting in Boot Menu is effective for one time only After system restart the device boot order will still be based on BIOS Setup settings lt END gt Q FLASH Press the lt End gt key to access the Q Flash utility directly without having to enter BIOS Setup first BIOS Setup 32 2 2 Main Menu Startup Guide Default The Startup Guide screen simplifies conventional complicated BIOS setup menus and presents only the most frequently used options in the easy to use interface It helps first time users to perform basic system setups more quickly and easily GIGABYTE Startup Guide ST Mode Smart Tweak Mode Differing from traditional interface the ST Mode provides a fancy and user friendl
76. r more information about Intel CPUs unique features please visit Intel s website BIOS Setup 48 Other PCI Device Priority Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other than the LAN storage device and graphics controllers Legacy OpROM Enables legacy option ROM only gt UEFI OpROM Enables UEFI option ROM only Default This item is configurable only when CSM Support is set to Always Network stack Disables or enables booting from the network to install a GPT format OS such as installing the OS from the Windows Deployment Services server Default Disabled Ipv4 PXE Support Enables or disables 4 PXE Support This item is configurable only when Network stack is enabled PXE Support Enables or disables IPv6 PXE Support This item is configurable only when Network stack is enabled Administrator Password Allows you to configure an administrator password Press lt Enter gt on this item type the password and then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt You must enter the administrator password or user password at system startup and when entering BIOS Setup Differing from the user password the administrator password allows you to make changes to all BIOS settings User Password Allows you to configure a user password Press lt Enter gt on this item type the p
77. rough the internal USB header Hin onnectors 1 x 24 pin main power connector 1 x 4 pin ATX 12V power connector 6 x SATA 6Gb s connectors 1 x CPU fan header 1 x system fan header 1 x front panel header 1 x front panel audio header 1 x USB 3 0 2 0 header 1 x USB 2 0 1 1 header 1 x serial port header 1 x S PDIF Out header 1 x Clear CMOS jumper 1 x chassis intrusion header D S K Back Panel gt Connectors 1 x PS 2 keyboard mouse port 2 X HDMI ports 2 5 antenna connectors 2T2R 1 x DVI I port 4 x USB 3 0 2 0 ports 2 x USB 2 0 1 1 ports 2 x RJ 45 ports 1 x optical S PDIF Out connector 5 x audio jacks Center Subwoofer Speaker Out Rear Speaker Out Line In Line Out Mic In O 1 0 Controller iTE I O Controller Chip Hardware Monitor System voltage detection CPU System temperature detection CPU System fan speed detection CPU System fan speed control Whether the fan speed control function is supported will depend on the cooler you install BIOS 2x64 Mbit flash ES Use of licensed AMI UEFI BIOS Support for DualBIOS PnP 1 0a DMI 2 7 SM BIOS 2 7 ACPI 2 0 11 Hardware Installation Unique Features Support for APP Center Available applications in APP Center may differ by motherboard model Supported functions of each application may also differ depending on motherboard specifications BIOS EasyTune EZ Setup Fast Boot
78. rt Clear CMOS Values wm i e Always turn off your computer and unplug the power cord from the power outlet before clearing A the CMOS values After system restart go to BIOS Setup to load factory defaults select Load Optimized Defaults or manually configure the BIOS settings refer to Chapter 2 BIOS Setup for BIOS configurations 14 CI Chassis Intrusion Header This motherboard provides a chassis detection feature that detects if the chassis cover has been removed This function requires a chassis with chassis intrusion detection design H Pin No Definition 1 Signal 2 GND BB Ad 29 Hardware Installation Hardware Installation 30 Chapter 2 BIOS Setup BIOS Basic Input and Output System records hardware parameters of the system in the CMOS on the motherboard Its major functions include conducting the Power On Self Test POST during system sta
79. rtup saving system parameters and loading operating system etc BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features When the power is turned off the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS To access the BIOS Setup program press the lt Delete gt key during the POST when the power is turned on To upgrade the BIOS use either the GIGABYTE Q Flash or BIOS utility e 2 allows the user to quickly and easily upgrade or back up BIOS without entering the operating system e BIOS is a Windows based utility that searches and downloads the latest version of BIOS from the Internet and updates the BIOS Because BIOS flashing is potentially risky if you do not encounter problems using the current A version of BIOS it is recommended that you not flash the BIOS To flash the BIOS do it with caution Inadequate BIOS flashing may result in system malfunction 115 recommended that you not alter the default settings unless you need to to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs try to clear the CMOS values and reset the board to default values Refer to the Load Optimized Defaults section in this chapter or introductions of the battery or the clear CMOS jumper in Chapte
80. sh Access Level Administrator This section provides information on your motherboard model and BIOS version You can also select the default language used by the BIOS and manually set the system time lt System Language Selects the default language used by the BIOS 7 System Date Sets the system date The date format is week read only month date and year Use Enter to switch between the Month Date and Year fields and use the Page Up or Page Down key to set the desired value 7 System Time Sets the system time The time format is hour minute and second For example 1 p m is 13 0 0 Use Enter to switch between the Hour Minute and Second fields and use the lt Page Up or Page Down key to set the desired value Access Level Displays the current access level depending on the type of password protection used If no password is set the default will display as Administrator The Administrator level allows you to make changes to all BIOS settings the User level only allows you to make changes to certain BIOS settings but not all 45 BIOS Setup Boot Option 2 Bootup NumLock State Security Option Full Screen LOGO Show Fast Boot Limit CPUID Maximum Execute Disable Bit Intel Virtualization Technology Intel TXT LT Support Dynamic Storage Accelerator UT d Windows 8 Features Boot Mode Selection LAN PXE Boot Option ROM Storage Boot Option Control Copyright
81. speed under the Fan Speed Percentage item b Full Speed Allows the fan to run at full speeds lt Fan Speed Percentage Allows you to control the fan speed This item is configurable only when System Fan Speed Control is set to Manual Options are 0 75 PWM value 2 50 PWM value C b Miscellaneous Settings GIGABYTE DualBIOS system Information BIOS Features Peripherals Power Management save amp Exit a Back M I T Miscellaneous Settings ST Mode English Q Flash PCIe Slot Configuration Auto Enabled Disabled PCle Slot Configuration Allows you to set the operation mode of the PCI Express slots to Gen 1 Gen 2 or Gen 3 Actual operation mode is subject to the hardware specification of each slot Auto lets the BIOS automatically configure this setting Default Auto 7 DMI Gen2 Speed Allows you to configure the DMI link speed Auto Lets the BIOS automatically configure this setting Enabled Sets the DMI link speed to Gen 2 Default Disabled Sets the DMI link speed to Gen 1 7 3DMark01 Boost Allows you to determine whether to enhance some legacy benchmark performance Default Disabled BIOS Setup 44 2 4 System Information GIGABYTE DualBIOS D Co NG Na 5j E v _ I M AS et x MIT 1 BIOS Features Peripherals Power Management Save amp Exit ST Mode English Q Flash Model Name 2Z97N UIFI BIOS Uersion Fig BIOS Date 04 02 2014 BIOS ID BAOGAGOM System Language Engli
82. ss lt Ctrl I gt to enter Configuration Utility Figure 9 Press Ctrl lt I gt to enter the RAID Configuration Utility Intel R Rapid Storage Technology Option ROM 13 0 0 2075 Copyright C Intel Corporation All Rights Reserved RAID Volumes None defined Physical Devices ID Device Model Serial Size Type Status Vol ID Hitachi HDS72105 JP1532FR3BWV7K 465 7GB 2 Hitachi HDS72105 JP1532ER046M2K 465 7GB Press lt C TRL gt to enter Configuration Utility Figure 9 Step 2 After you press Ctrl lt I gt the MAIN MENU screen will appear Figure 10 Create RAID Volume If you want to create a RAID array select Create RAID Volume in MAIN MENU and press lt Enter gt 1 MAIN MENU 1 Create RAID Volume Recovery Volume Options 2 Delete RAID Volume Acceleration Options 3 Reset Disks to Non RAID Exit 15 DISK VOLUME INFORMATION RAID Volumes None defined Physical Deivces ID Device Model Serial Size Type Status Vol ID 1 Hitachi HDS72105 JP1532FR3BWV7K 465 7GB 2 Hitachi HDS72105 JP1532ER046M2K 465 7GB 63 Configuring SATA Hard Drive s Step 3 After entering the CREATE VOLUME MENU screen enter a volume name with 1 16 letters letters cannot be special characters under the Name item and press lt Enter gt Then select a RAID level Figure 11 RAID levels supported include RAID 0 RAID 1 RAID 10 and RAID 5 the sel
83. tem will work stably with the overclock overvoltage settings you made is dependent Show all information about M I T status b Aduanced Frequency Settings gt Advanced Memory Settings gt Advanced Voltage Settings gt PC Health Status gt Miscellaneous Settings BIOS Version Fig BCLK 100 02MHz Select Screen 11 Click Select Item CPU Frequency 3901 36MHz Enter Dbl Click Select Memory Frequency 1333 60MHz PU PD Change Opt Total Memory Size 1024MB Smart Tweak Mode Previous Values CPU Temperature 45 0 C Optimized Defaults Q Flash Ucore 1 140U Systen Information DRAM Voltage F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Copyright C 2014 American Megatrends Inc This section provides information on the BIOS version CPU base clock CPU frequency memory frequency total memory size CPU temperature Vcore and memory voltage BIOS Setup 36 gt Current Status This screen provides information on CPU memory frequencies parameters Advanced Frequency Settings DualBIOS e Ig 75 ay FX system Information BIOS Features Peripherals Pouer Management Save amp Exit Back M I T Aduanced Frequency Settings ST Mode English Q Flash Performance Upgrade Auto Auto Auto Auto Auto Disabled Auto lt Performance Upgraded Note Provides you with five different overclocking
84. the chassis intrusion status record set Reset Case Open Status to Enabled save the settings to the CMOS and then restart your system CPU Vcore CPU VRIN DRAM Voltage 3 3V 5V 12V CPU VAXG Displays the current system voltages CPU SystemTemperature Displays current CPU System temperature CPU System Fan Speed Displays current CPU system fan speed CPU Fan Speed Control Allows you to determine whether to enable the fan speed control function and adjust the fan speed Normal Allows the fan to run at different speeds according to the CPU temperature You can adjust the fan speed with EasyTune based on your system requirements Default Silent Allows the fan to run at slow speeds gt gt Manual Allows you to control the fan speed under the Fan Speed Percentage item Full Speed Allows the fan to run at full speeds Fan Speed Percentage Allows you to control the fan speed This item is configurable only when CPU Fan Speed Control is set to Manual Options 0 75 PWM value 2 50 PWM value 43 BIOS Setup lt System Fan Speed Control Allows you to determine whether to enable the fan speed control function and adjust the fan speed Normal Allows the fan to run at different speeds according to the system temperature You can adjust the fan speed with EasyTune based on your system requirements Default Silent Allows the fan to run at slow speeds gt gt Manual Allows you to control the fan
85. tions Save amp Exit Save all the changes made in the BIOS Setup program to the CMOS and exit BIOS Setup You can save the current BIOS settings to a profile or load optimized defaults for optimal performance system operations 35 BIOS Setup GIGABYTE DualBIOS Show all information about M I T status gt Advanced Frequency Settings b Aduanced Memory Settings gt Advanced Voltage Settings gt PC Health Status b Miscellaneous Settings BIOS Version Fig BCLK 100 02MHz Select Screen 11 Click Select Item CPU Frequency 3901 36MHz Enter Dbl Click Select Memory Frequency 1333 60MHz PU PD Change Opt Total Memory Size 1024MB Smart Tweak Mode Previous Values CPU Temperature 45 07 Optimized Defaults Q Flash Ucore 1 1400 System Information DRAM Voltage 1 500U F10 Save amp Exit F12 Print Screen FAT16 32 Format Only ESC Right Click Exit Copyright 2014 American Megatrends Inc on your overall system configurations Incorrectly doing overclock overvoltage may result in damage to CPU chipset or memory and reduce the useful life of these components This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs clear the CMOS values and reset the board to default values GIGABYTE DualBIOS Whether the sys
86. ue rayonn e quivalente P I R E applicable dans les bandes 5 25 5 35 GHz et 5 725 5 85 GHz en fonctionement point a point Cet appareil num rique de la classe est conforme la norme NMB 003 No 4 et CNR 210 No 4 Dec 2000 et No 5 Nov 2001 Pour emp cher que cet appareil cause du brouillage au service faisant l objet d une licence il doit tre utilis a l int rieur et devrait tre plac loin des fen tres afin de fournir un cran de blindage maximal Si le mat riel ou son antenne d mission est install l ext rieur il doit faire l objet d une licence European Community Directive R amp TTE Directive Compliance Statement This equipment complies with all the requirements and other relevant provisions of Directive 1999 5 EC of the European Parliament and the Council of March 9 1999 on Radio Equipment and Telecommunication Terminal Equipment R amp TTE This equipment is suitable for home and office use in all the European Community Member States and EFTA Member States The low band 5 15 5 35 GHZ is for indoor use only France Pour la France metropolitaine 2 400 2 4835 GHz Canaux 1 13 autoris en usage int rieur 2 400 2 454 GHz canaux 1 7 autoris en usage ext rieur Pour la Guyane et la R union 2 400 2 4835 GHz Canaux 1 13 autoris en usage int rieur 2 420 2 4835 GHz canaux 5 13 autoris en usage ext rieur Italy The use of these equipments is regulated by 1
87. unction ASPM Default Disabled PEG ASPM Allows you to configure the ASPM mode for the device connected to the CPU PEG bus Auto lets the BIOS automatically configure this setting This item is configurable only when Platform Power Management is set to Enabled Default Auto PCle ASPM Allows you to configure the ASPM mode for the device connected to Chipset s PCI Express bus Auto lets the BIOS automatically configure this setting This item is configurable only when Platform Power Management is set to Enabled Default Auto CPU DMI Link ASPM Control Allows you to configure the ASPM mode for the CPU side of the DMI link Auto lets the BIOS automatically configure this setting This item is configurable only when Platform Power Management is set to Enabled Default LOsL 1 PCH DMI Link ASPM Control Allows you to configure the ASPM mode for both CPU side and Chipset side of the DMI link Auto lets the BIOS automatically configure this setting This item is configurable only when Platform Power Management is set to Enabled Default Enabled 55 BIOS Setup 2 8 a Save amp Exit GIGABYTE DualBIOS y gt e MIT System Information BIOS Features Peripherals Pouer Management ST Mode English Q Flash Load Optimized Defaults Save amp Exit Setup Press lt Enter gt on this item and select Yes This saves the changes to the CMOS and exits the BIOS Setup program Select No or press lt Esc gt
88. ut from the slot Hardware Installation 18 1 6 Back Panel Connectors 5 USB 2 0 1 1 Port The USB port supports the USB 2 0 1 1 specification Use this port for USB devices such as a USB keyboard mouse USB printer USB flash drive and etc PS 2 Keyboard Mouse Port Use this port to connect a PS 2 mouse or keyboard SMA Antenna Connectors 2T2R Use this connector to connect an antenna Tighten the antenna cables to the antenna connectors and then move the antenna to a place where the signal is good DVI I Port The DVI I port conforms to the DVI I specification and supports a maximum resolution of 1920x1200 60Hz the actual resolutions supported depend on the monitor being used Connect a monitor that supports DVI I connection to this port HDMI Port LOI The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD MuLtimeoia inrenrace Master Audio formats It also supports up to 192KHz 24bit 8 channel audio output You can use this port to connect your HDMI supported monitor The maximum supported resolution is 4096x2160 24Hz or 2560x1600 60Hz but the actual resolutions supported are dependent on the monitor being used After installing the HDMI device make sure to set the default sound playback device to HDMI The item ER name may differ depending on your operating system The screenshot below is from Windows 8 1 In Windows 8 1 select Apps gt Control Panel gt
89. we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals Waste Electrical Electronic Equipment WEEE Directive Statement GIGABYTE will fulfill the national laws as interpreted from the 2002 96 EC WEEE Waste Electrical and Electronic Equipment directive The WEEE Directive specifies the treatment collection recycling and disposal of electric and electronic devices and their components Under the Directive used equipment must be marked collected separately and disposed of properly WEEE Symbol Statement The symbol shown below is the product or on its packaging which indicates that this product ES must not be disposed of with other waste Instead the device should be taken to the waste collection centers for activation of the treatment collection recycling and disposal procedure The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local government office your household waste disposal service or where you purchased the product for details of environmentally safe recycling When your electrical or electronic equipment is no longer useful to you take it back to your local or regional waste colle
90. y BIOS environment where users can easily point and click through various settings and make adjustments for optimum performance In ST Mode you can use your mouse to move through the option menus for quick configuration or press lt F2 gt to switch to the traditional BIOS Setup screen GIGABYTE UEFI BIOS system to its defaults The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version Only for GA Z97N WIFI ER When the system is not stable as usual select the Load Optimized Defaults item to set your 33 BIOS Setup Classic Setup Classic Setup is the conventional BIOS Setup interface where you can press the arrow keys on your keyboard to move among the items and press lt Enter gt to accept or enter a sub menu Or you can use your mouse to select the item you want Sample BIOS Version GA Z97N WIFI F1g e MIT Switch to ST Mode Boot Option 1 GIGABYTE DualBIOS o gt PA tS Y Setup Menus A System Information Peripherals Power Management Save amp Exit ST Mode English O Flash Enter Q Flash rn Select Default UEFI 8 Language SanDisk Enabled Help System Enabled Disabled Disabled Enabled Enabled Disabled Disabled Enabled Function Keys Other 05 UEFI Disabled Legacy Configuration Items Current Settings Classic Setup Function Keys lt gt lt gt gt Move the selection bar to select a
91. z bands These radar stations can cause interference with and or damage to this device The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E I R P limit for the 5 25 to 5 35 and 5 725 to 5 85 GHz frequency range in point to point operation This Class B digital apparatus complies with Canadian ICES 003 Issue 4 and RSS 210 No 4 Dec 2000 and No 5 Nov 2001 To prevent radio interference to the licensed service this device is intended to be operated indoors and away from windows to provide maximum shielding Equipment or its transmit antenna that is installed outdoors is subject to licensing Attention l utilisation d un r seau sans fil IEEE802 11a est r streinte une utilisation en int rieur cause du fonctionement dans la bande de fr quence 5 15 5 25 GHz Industry Canada requiert que ce produit soit utilis l int rieur des b timents pour la bande de fr quence 5 15 5 25 GHz afin de r duire les possibilit s d interf rences nuisibles aux canaux co existants des syst mes de transmission satellites Les radars de puissances ont fait l objet d une allocation primaire de fr quences dans les bandes 5 25 5 35 GHz et 5 65 5 85 GHz Ces stations radar peuvent cr er des interf rences avec ce produit et ou lui tre nuisible 5 Appendix Le gain d antenne maximum permissible pour une utilisation avec ce produit est de 6 dBi afin d tre conforme aux limites de puissance isotropiq

Gigabyte GA-H97N-WIFI motherboard

Contents

Download Pdf Manuals

Related Search

Related Contents