Home

Da-Lite 34502L projection screen

1. INSTRUCTION BOOK FOR Tensioned Cosmopolitan Electrol For Sizes Up To 10 x 10 DA LITE Important Safety Instructions Pre Installation When using your video equipment basic safety precautions 1 Carefully unpack screen and remove outer wrapping Should always be followed including the following from Case 1 Read and understand all instructions before using 2 Remove shipping brackets by removing the screws from the slat bar and wooden board and use supplied 1 8 next 2 Position the cord so that it will not be tripped over pulled or key to remove silver shipping brackets attached to slat contact hot surfaces 3 Always handle screen in horizontal position 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 Jo reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric Shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons Installation There are three methods of mounting to include Flush against wall Suspended from ceiling use extension brackets and recessed above ceiling Wall Mounted Concealed Allow Room For Access Cei
2. OOD Splitter Dry Contacts ILT RJ9 Pin Outs Tab Is Facing U eee IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 4 conductor connection that is accessible IR or Up Ground Common 5V DN or Data Screen Adjustment The screen surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite The screen should not be adjusted for more or less drop The fabric cables are adjusted for proper vertical and lateral tension at Da Lite A CAUTION Contact Da Lite at 800 622 3737 or 574 267 8101 if screen motor needs adjustment A ATTENTION Contactez Da Lite au 800 622 3737 ou au 574 267 8101 au cas le moteur de l cran a besoin d tre ajust Troubleshooting Visit www da lite com products tutorials php to find installation info da lite com or by phone at 800 622 3737 or 574 267 8101 and troubleshooting tutorials You will also find a link to Live Chat with any troubleshooting questions for interactive Support and you can contact us by email at Symptom Cause Solution Verify 15 125V or 220 240V If insufficient voltage rewire Incorrect line voltage l l are incoming electric line Screen will not operate Blown fuse Replace fuse Motor does not hum Tripped circuit breaker Reset circuit breaker Check
3. above Tighten all loose wire connections Correct any improper connections Down Position No power to operating switch or junction i j A Check for power across black and white leads Up Position Check for power across red and white leads Power at junction box Let motor cool down for 15 minutes Try again Thermal overload tripped Broken wire in the up or down position Check for continuity Cut off old splice and reconnect Replace motor assembly Defective motor limit switch or capacitor p NOTE Motor is a sealed assembly Motor hums Temporary binding With power off turn roller by hand to free binding Capacitor burned out Replace motor assembly Incorrect stopping position in i i Down limit switch out of adjustment Contact Da Lite at 800 622 3737 or 5 4 267 8101 downward direction Incorrect stopping position in i Up limit switch out of adjustment Contact Da Lite at 800 622 3737 or 574 267 8101 upward direction Noise NOTE Screen will operate Gear noise Replace motor assembly with a low pitched hum Defective brake Replace motor assembly Roller displaced from Pin end slipped out of nylon bearing Realign pin end bracket mounting bracket LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da Lite branded products to the original purchaser only to be free from defects in mater
4. CABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 8773254832 E info da lite com www da lite com DL 0264 Rev 1 07 14 2014 Milestone AV Technologies LLC Printed in U S A 76063
5. creen Case In Which Internal Wiring Terminates In White Black and Red Leads Poa a Peo o a W w O es Common White a White 3 Diameter For Ceiling Mounting Enclosure Cover e Diameter Opening For Electrical Settings Picture Surface Slat Wiring Enclosure Cover up gt Red L Off Down Ly Black With Operating Switch In Multiple Control F Meow And Plate Furnished Installations This With Screen SPDT Switch Is Replaced By Se View AC Common With Center Off The Low Voltage Of Switch Control Operated And Box 120 V 60 Hz 25 Max Amp From Push Button This Switch Cannot Be Used With LVC i AE NOTE A single switch cannot be used to operate more than one screen Contact the factory for further information 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram included in wall switch box included with screen 120V Wiring Diagram with Optional Built In Low Voltage Control 3 conductor 20 24 gauge wire can be used in place of the Supplied RJ 14 cable to connect the wall switch Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board IMPORTANT NOTE he wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire t
6. creen trigger output to the length required to reach the VPI When extending the low voltage connection from the projector s screen trigger output polarity does not matter The red and black wires from the VPI are interchangeable Front Of Wall Switch Wall Switch Black ke Red lee Loo d s i2 Volt Screen Trigger On Projector VPI Trigger Module Black Hot White Common IMPORTANT NOTE he wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible 3 conductor 20 24 gauge wire can be used in place of the Supplied RJ 14 cable to connect the wall switch Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board RJ 22 Jack RJ 22 Output Up Noni Dry Contacts Common Bus BUS 5V RJ 45 Receptacle RJ 45 Jack Data Cable Ground Must Be Connected To Building Ground Power Input 120VAC 60Hz Tensioned Cosmopolitan Electrol Installation Connect Supplied RJO Cable to Splitter and Switch or use 4 Cable Conductor to Connect PE r to Screw Terminals 240V Wiring Diagram With Optional Built In Optional IR and RF UP DN GND 5V Blue Common Brown Hot DAOVACSOHZ ae p m 3 Position oelah cine Ground Must be Green lal C Connected to Building Ground Ground to Case 2 z Front Back
7. he switch or provide a 3 conductor connection that is accessible RJ 22 Jack LED RJ 22 Output D Down Dry Contacts Inputs if 2 Common N Oy BUS RJ 45 Receptacle Up Limit Tactile Button Down Limit Tactile Button Front Of Back Of Wall Switch Wall Switch Power Wire Green Ground Black Hot White Common Ground Must Be Connected To Building Ground Power Input 120VAC 60Hz RJ 14 Pin Outs Tab Is Facing Up RJ 22 Pin Outs Tab Is Facing Up RJ 45 Pin Outs Tab Is Facing Up 12V Blue Manual 2 Brown Bus RP Data C white Bus RP Data Yellow 12v Bue Bus RP Data ___ Yellow RO Data Green RO Data Green RO Data E Green 5V __ Red 5V ____ Red 5V Red Ground L Black Ground C Black Ground Black E RQ Clock Orange C RQ Clock Whit ere a Manual 1 L Purple Supplied RJ 14 cable Standard RJ 22 can be used in place of RJ 14 120V Wiring Diagram with Optional Built In Video Projector Interface A CAUTION The projector must be turned off before connecting the trigger wires to the projector Failure to do so may damage the controller A ATTENTION Le projecteur doit tre teint avant de brancher les fils de d clenchement a celui ci Tout manquement cette instruction pourrait endommager le contr leur Use 2 conductor 20 24 gauge wire to extend the low voltage connection from the projector s 5 or 12 volt s
8. ials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also Nave other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLI
9. ling Use No 6 Mounted Brackets To Hang Behind Picture Picture Picture Beam or Valance Surface Surface Surface lt Picture i Surface NOTE Under no circumstances should unit be completely sealed in recessed installation Allow access for service Picture surface is centered in case Case extends 5 1 2 beyond surface on either end Do not attach anything to screen slat rod or bottom fabric pocket Make sure screen is level Use a carpenter s level and plumb level 3 Test installation by running screen up and down a few times Be prepared to stop screen Standard Duty Cycle CAUTION Do not cut wrapping paper or tape with knife or an A tical 1 MIN ON 3 MIN OFF sharp tool Remove by hand NOTE Must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA C221 and the National Electric Code NEC NFPA 70 A ATTENTION Ne coupez pas le papier d emballage ou le ruban adh sif avec un couteau ou un outil tranchant Retirez ala main 2 Install electrical hook up that applies to your unit Make sure to review your Electrical Installation Checklists and Wiring Diagrams included for either 120 Volt Switch 220 240 Volt Switch or Low Voltage Control Tensioned Cosmopolitan Electrol Installation Overall Length of Case Between Hanger Eyes Diameter Hole For Wall 5 4 Installation 120V Wiring Diagram cus To Junction Box Mounted In S

Da-Lite 34502L projection screen

Contents

Download Pdf Manuals

Related Search

Related Contents