Philips HTS5553
Contents
1. e MUSIC iLINK A MUSIC iLINK Audio input from an MP3 player 2 lt USB Audio video or picture input from a USB storage device Rear connectors 1 Standby On Switch the home theater on or to standby Qo gt 11 Play Pause Start pause or resume play 3 E Stop Stop play n radio mode press and hold to erase he current preset radio stations SOURCE Select an audio or video source for the home theater lt Increase or decrease volume A Open Close Open or close the disc compartment or eject the disc D Display panel Disc compartment Connectors This section includes an overview of the connectors available on your home theater ORO 00000 AC MAINS Connect to the power supply SPEAKERS Connect to the supplied speakers and subwoofer Wireless Rear Audio Connect to a Philips wireless module Model Philips RVVSS5512 sold separately HDMI OUT ARC Connect to the HDMI input on the TV VIDEO OUT VIDEO Connect to the composite video input on the TV ANTENNA FM 75 Q Signal input from an antenna cable or satellite AUDIO IN AUX 1 AUX 2 Connect to an analog audio output on the TV or an analog device DIGITAL IN OPTICAL Connect to an optical audio output on the or a digital devi2. 665 nm DVD 770 800 nm CD Output power 6 mW DVD 7 mW VCD CD Beam divergence 60 degrees 20 EN 8 Troubleshooting Warning Risk of electric shock Never remove the casing of the product To keep the warranty valid never try to repair the product yourself If you have problems using this product check the following points before you request service If you still have a problem get support at www philips com support Main unit The buttons on the home theater do not work Disconnect the home theater from the power supply for a few minutes then reconnect Picture No picture Make sure that the TV is switched to the correct source for the home theater If this happens when you change the TV system press A to open the disc compartment and then 439 on the remote control to restore the default TV system No picture on a TV connected through HDMI Make sure that the HDMI cable is not faulty If it is faulty replace it with a new cable If this happens when you change the HDMI video resolution press 4 to open the disc compartment and then 304 on the remote control to restore the default setting Wait for 10 seconds for auto recovery or change the HDMI video setting Disc does not play high definition video e Make sure that the disc contains high definition video Make sure that the TV supports high definition video Use an HDMI cable to connect
3. gt Audio Sync forward VCD SVCD can only slow forward Picture Rotate the picture clockwise or counter clockwise Data files Left Right g Video Fast backward or fast Your home theater can play pictures audio and orward Press repeatedly to video files contained in a disc or a USB storage change the search speed device Before you play a file check that the file Flip the picture verti format is supported by your home theater see cally or horizontally File formats on page 19 oK Confirm an entry or selection 1 Play the files from a disc or USB storage device gt 11 Play Start pause or resume play 2 stop play press Pause To resume the video from where you H Stop play stopped press IM I4 pl Skip to the previous or next track chapter or file SUBTITLE Select subtitle language for video Note DISC Access or exit the disc menu To play DivX DRM protected files connect your AUDIO SYNC Select an audio language or channel home theater to a TV through an HDMI cable SCREEN Fit the picture format to the TV FIT screen ZOOM Zoom into a video scene or picture EN 11 English Subtitles If your video has subtitles in multiple languages select a subtitle language Make sure that the subtitle file has the exact same name as the video file For example if the video file is named movie avi name the subtitle file as movie srt or movie sub Your home theater support
4. he ratings shown on the plug e aBS 1362 approval and he ASTA approval mark Contact your dealer if you are not sure about what type of fuse to use Caution To conform with the EMC directive 2004 108 EC do not detach the plug from the power cord Compliance This product is in compliance with the essential requirements and other relevant provisions of Directives 2006 95 EC Low Voltage 2004 108 22 Trademarks CX DOLBY DIGITAL PRO LOGIC II Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories S dts Digital Surround Manufactured under license under U S Patent Nos 5 956 674 5 974 380 6 487 535 amp other US and worldwide patents issued amp pending DTS the Symbol amp DTS and the Symbol together are registered trademarks amp DTS Digital Surround and the DTS logos are trademarks of DTS Inc Product includes software DTS Inc All Rights Reserved DIVX ULTRA DivX DivX Ultra DivX Certified and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license DivX Ultra Certified to play DivX video with advanced features and premium content ABOUT DIVX VIDEO DivX is a digital video format created by DivX LLC a subsidiary of Rovi Corporation This is an official DivX Certified device that plays DivX video Vi
5. 9065 Church Slavic Slavonic 6785 Chuvash 6786 Corsican 6779 esky 6783 Dansk 6865 Deutsch 6869 Dzongkha 6890 English 6978 Esperanto 6979 Estonian 6984 Euskara 6985 di OEI 6976 Faroese 7079 Francais 7082 Frysk 7089 Fijian 7074 Gaelic Scottish Gaelic 7168 Gallegan 7176 Georgian 7565 Gikuyu Kikuyu 7573 Guarani 7178 Gujarati 7185 Hausa 7265 Herero 7290 Hindi 7273 Hiri Motu 7279 Hrwatski 6779 Ido 7379 Interlingua International 7365 Interlingue 7365 Inuktitut 7385 Inupiaq Irish islenska Italiano Ivrit Japanese Javanese Kalaallisut Kannada Kashmiri Kazakh Kernewek Khmer Kinyarwanda Kirghiz Komi Korean Kuanyama Kwanyama Kurdish Lao Latina Latvian Letzeburgesch Limburgan Limburger Lingala Lithuanian Luxembourgish Macedonian Malagasy Magyar Malayalam Maltese Manx Maori Marathi Marshallese Moldavian Mongolian Nauru Navaho Navajo Ndebele North Ndebele South Ndonga Nederlands Nepali Norsk Northern Sami North Ndebele Norwegian Nynorsk Occitan Provencal Old Bulgarian Old Slavonic Oriya Oromo Ossetian Ossetic Pali Panjabi Persian Polski Portugu s 7375 7165 7383 7384 7269 7465 7486 7576 7578 7583 7575 7587 577 8287 7589 7586 7579 7574 7585 7679 7665 7686 7666 7673 7678 7684 7666 7775 7771 7285 7776 7784 7186 7773 7782 7772 7779 7778 7865 7886 7868 7882 7871 7876 7869 7879 8369 7868 7878 7967 6785 7982 797
6. Subtitles on page 12 Select the correct character set see Subtitles page 12 Make sure that the format of the USB storage device is compatible with the home heater Make sure that the file system on the USB storage device is supported by the home heater entry or sign appears on the TV The operation is not possible EasyLink does not work Make sure that the home theater is connected to a Philips brand EasyLink TV and he EasyLink option is turned on see Set up EasyLink HDMI CEC control on page 9 When you switch on the TV the home theater automatically switches on This behavior is normal when you are using Philips EasyLink HDMI CEC To make the home theater work independently switch off EasyLink EN 21 English 9 Notice This section contains the legal and trademark notices Copyright Be responsible Respect copyrights This item incorporates copy protection technology that is protected by U S patents and other intellectual property rights of Rovi Corporation Reverse engineering and disassembly are prohibited Copyright in the UK Recording and playback of material may require consent See Copyright Act 1956 and The Performers Protection Acts 1958 to 1972 Mains fuse UK only This information applies only to products with a UK mains plug This product is fitted with an approved molded plug If you replace the fuse use one with
7. contains the files is created in the USB storage device To exit the menu select Exit and then press OK Note Do not remove the USB and press any buttons when the conversion is in progress DTS CDs and copy protected CDs cannot be converted Write protected or password protected USB storage device cannot be used to store MP3 files Choose sound This section helps you choose the ideal sound for your video or music Sound mode Select predefined sound modes to suit your video or music 1 Press SOUND repeatedly to select a sound mode e MOVIE Enjoy a cinematic audio experience specially enhanced for movies e MUSIC Recreate the original recording environment of your music in the studio or at a concert e ORIGINAL Experience the original sound of your movies and music without added sound effects NEWS Hear every word with optimized speech and clear vocals e GAMING Enjoy thrilling arcade sounds ideal for action packed video games or loud parties Surround sound mode Experience an immersive audio experience with surround sound modes 1 Press SURR repeatedly to select a surround mode STEREO Enhanced stereo sound Ideal for party music e MULTI CH DOLBY PLII Traditional 5 1 channel for a more relaxing cinematic experience STEREO Two channel stereo sound Ideal for listening to music Note e Ifthe audio source is a 2 1 channel mul
8. old product helps to prevent potential negative consequences for the environment and human health Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health Help and support Philips provides extensive online support Visit our website at www philips com support to e download the complete user manual e print the quick start guide watch video tutorials available only for selected models find answers to frequently answered questions FAOs email us a question e chat with our support representative Follow the instructions on the website to select your language and then enter your product model number Alternatively you can contact Philips Consumer Care in your country Before you contact Philips note down the model number and serial number of your product You can find this information on the back or bottom of your product EN 3 English 2 Your home theater Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Main unit This section includes an overview of the main unit Front connectors
9. speaker Make sure that the left right and the center speakers are at equal distance from your seating position 4 REAR LEFT rear left and REAR RIGHT rear right speakers Place the rear surround speakers to the left and right side of your seating position either in line with it or slightly behind it 5 SUBWOOFER subwoofer Place the subwoofer at least one meter to the left or right of the TV Leave about 10 centimeter clearance from the wall Make your rear speakers wireless Connect the rear speakers to your home theater wirelessly using a wireless module accessory For details see the wireless module user manual What you need e A Philips wireless module Model Philips RWSS5512 sold separately 1 Connect the wireless transmitter to the Wireless Rear Audio connector on your home theater lt Wireless Rear Audio 2 Connect the rear speakers to the wireless receiver 3 Connect the wireless receiver to the power supply 2V Gar Connect to TV Connect your home theater to a TV to watch videos You can listen to the TV audio through your home theater speakers Use the best quality connection available on your home theater and TV Option 1 Connect to TV through HDMI ARC Best quality video Your home theater supports HDMI version 1 4 Audio Return Channel ARC If you
10. 7 7983 8073 8065 7065 8076 8084 Pushto Russian Quechua Raeto Romance Romanian Rundi Samoan Sango Sanskrit Sardinian Serbian Shona Shqip Sindhi Sinhalese Slovensky Slovenian Somali Sotho Southern South Ndebele Sundanese Suomi Swahili Swati Svenska Tagalog Tahitian Tajik Tamil Tatar Telugu Thai Tibetan Tigrinya Tonga Tonga Islands Tsonga Tswana T rkce Turkmen Twi Uighur Ukrainian Urdu Uzbek Vietnamese Volapuk Walloon Welsh Wolof Xhosa Yiddish Yoruba Zulu 8083 8285 8185 8277 8279 8278 8377 8371 8365 8367 8382 8378 8381 8368 8373 8373 8376 8379 8384 7882 8385 7073 8387 8383 8386 8476 8489 8471 8465 8484 8469 8472 6679 8473 8479 8483 8478 8482 8475 8487 8571 8575 8582 8590 8673 8679 8765 6789 8779 8872 8973 8979 9085 2012 Koninklijke Philips Electronics N V All rights reserved sgpjp_1202 51_v1 PHILIPS
11. For a comprehensive interactive guide visit www connectivityguide philips com Note For identification and supply ratings see the type plate at the back or bottom of the product Before you make or change any connections make sure that all devices are disconnected from the power outlet Connect speakers The speaker cables are color coded for easy connection To connect a speaker to your home theater match the color on the speaker cable to the color on the connector Speaker position plays a critical role in setting up a surround sound effect For best effect position all the speakers towards the seating position and place them close to your ear level seated as gf SUB FRONT 7 FRONT WOOFER LEFT RIGHT Note Surround sound depends on factors such as room shape and size type of wall and ceiling windows and reflective surfaces and speaker acoustics Experiment with the speaker positions to find the optimum setting for you Follow these general guidelines for speakers placement Seating position This is the center of your listening area 2 FRONT CENTER front center speaker Place the center speaker directly in front of the seating position either above or below your TV 3 FRONT LEFT front left and FRONT RIGHT front right speakers Place the left and right speakers in the front and at equal distance from the center
12. INK connector on your home theater Press SOURCE repeatedly until MUSIC I LINK appears on the display panel W N Press the buttons on the MP3 player to select and play audio files Create MP3 files Use your home theater to convert audio CDs into MP3 files What you need e An audio disc A USB storage device Connect a USB storage device to your home theater Play your audio CD CDDA Press CREATE MP3 L gt confirmation message is displayed A WN Select Yes and then press OK The create MP3 screen is displayed The right panel contains MP3 settings and the left panel shows the audio tracks CREATE MP3 OPTIONS TRACK Speed Normal Track01 04 14 Bitrate 128kbps Track02 04 17 CRTID3 Yes O Track03 03 58 O Track04 04 51 Device USB1 O Track05 03 53 SUMMARY Trackoe 04 09 Select Track 0 O Track07 04 38 Time 00 00 b d Start Exit Select All Deselect All Press the Navigation buttons and OK to select and change Speed Select the write to file speed Bitrate Select the conversion quality CRT ID3 Copy the tracks information when converting to MP3 files Device Select the USB storage device which you use to store the MP3 files Navigate to the right panel select the audio tracks and press OK To select all tracks navigate to Select All and then press OK Select Start and then press OK to start the MP3 conversion L gt A new folder which
13. Press again to stop music EN 13 English Radio Listen to FM radio on your home theater and store up to 40 radio stations Note AM and digital radio are not supported f no stereo signal is detected or if fewer than five stations are found you are prompted to install the radio stations again 1 Connect the FM antenna to the ANTENNA FM on your home theater For the best reception place the antenna away from the TV or other sources of radiation 2 Press RADIO f you have already installed the radio stations the last channel that you listened to is played L gt f you have not installed any radio stations the message AUTO INSTALL PRESS PLAY appears on the display panel press 3 Use the remote control to listen or to change radio stations Button Action Numeric Select a preset radio station buttons I4 gt l Navigation Left Right Search for a radio station buttons Up Down Fine tune a radio frequency a Press to stop the installation of radio stations Press and hold to erase the preset radio station PROGRAM anual Press once to access program mode and press again to store the radio station Automatic Press and hold for three seconds to reinstall the radio stations 14 EN MP3 player Connect a MP3 player to play audio files What you need An MP3 player 3 5mm stereo audio cable Connect the MP3 player to the MUSIC iL
14. Register your product and get support at www philips com welcome HTS5533 HTS5543 HTS5553 User manual PHILIPS Contents 1 Important 2 Safety 2 Care for your product 3 Care of the environment 3 Help and support 3 2 Your home theater 4 Main unit 4 Connectors 4 Remote control 5 3 Connect and set up 6 Connect speakers 6 Connect to TV 7 Connect audio from TV and other devices 8 Set up speakers 9 Set up EasyLink HDMI CEC control 9 4 Use your home theater 1 Discs 11 Data files 1 USB storage devices 12 Audio video and picture options 13 Radio 14 MP3 player 14 Create MP3 files 14 Choose sound 15 5 Change settings 16 Language settings 16 Picture and video settings 16 Audio settings 16 Parental control settings 17 Display settings 17 Energy saving settings 17 Restore default settings 17 6 Update software 18 Check software version 18 Update software through USB 18 7 Product specifications 19 8 Troubleshooting 20 9 Notice 22 Copyright 22 Mains fuse UK only 22 Compliance 22 Trademarks 22 10 Index 23 EN 1 English 1 Important Read and understand all instructions before you use your product If damage is caused by failure to follow instructions the warranty does not apply Safety Risk of electric shock or fire lever expose the produ rain or water 38 near nake
15. are not available 2 Press the Navigation buttons and OK to select and change Title Select a specific title Chapter Select a specific chapter Track Select a specific track for VCD SVCD only e Audio Select audio language for video Subtitle Select subtitle language for video Angle Select video scenes recorded in different camera angels TT Time Skip to a specific part of the video by entering the title time Ch Time Skip to a specific part of the video by entering the chapter time Disc Time Skip to a specific part of the video by entering the disc time for VCD SVCD only Track Time Skip to a specific part of the video by entering the track time for VCD SVCD only Preview Select a content preview for disc Repeat Select a repeat mode Time Disp Select the information of time display Picture options 1 Press D INFO to access picture preview mode Ly 12 thumbnail pictures are displayed 2 Press IJ PI to go to previous or next preview page 3 Press the Navigation buttons and OK to select a picture Musical slideshow If the picture and audio files are from the same disc or USB storage device you can create a musical slideshow Select an audio track and then press OK Press D BACK and then go to the picture folder NA Select a picture and then press OK to start the slideshow Press to stop slideshow UA w
16. ce DIGITAL IN COAXIAL Connect to a coaxial audio output on the TV or a digital device Remote control This section includes an overview of the remote control ui HOME THEATER SYSTEM w Do 9 Standby On Switch the home theater on or to standby When EasyLink is enabled press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby O 4 Open Close Open or close the disc compartment or eject the disc Source buttons e DISC Switch to disc source Access or exit the disc menu when you play a disc e AUDIO SOURCE Select an audio input source e RADIO Switch to FM radio USB Switch to USB storage device Navigation buttons avigate menus n video mode press left or right to fast backward or fast forward press up or n radio mode press left or right to search a radio station press up or down o fine tune a radio frequency OK Confirm an entry or selection gt BACK Return to a previous menu screen I4 Pl Previous Next Skip to the previous or next track chapter or file n radio mode select a preset radio station Mute Mute or restore volume VOL Increase or decrease volume SOUND Select a sound mode Numeric buttons Select an item to play ANGLE Select video scenes recorded in different camera angels REPEAT PROGRAM Select or
17. d and then press OK Display settings 1 Press SETUP 2 Select Preference Setup and then press OK Enable or disable the content menu navigation of VCD and SVCD discs with Play Back Control feature e MP3 JPEG Display Select the content display for MP3 JPEG files Energy saving settings 1 Press SETUP 2 Select General Setup and then press OK Screen Saver Switch the home theater o screen saver mode after 10 minutes of no activity e Auto Standby Switch the home theater o standby mode after 30 minutes of no activity when in disc or USB mode Sleep Timer Switch the home theater standby mode after the elapsed time Display Dim Set the brightness of the home theater front panel display Restore default settings 1 Press SETUP 2 Select Preference Setup gt Default and then press OK 3 Select Reset and then press OK to confirm Your home theater is reset to its default settings except for parental control setting EN 17 English 6 Update software Philips continually tries to improve its products To get the best features and support update your home theater with the latest software Compare the version of your current software with the latest version on www philips com support If the current version is lower than the atest version available on the Philips support website upgrade your home theater with the atest s
18. d flames or o including direc ever insert objects in sunlight ct and accessories to ever place liquid containers such vases near the product If liquids are spilt on or the product disconnect it from the power outlet immediately Contact Philips Consumer Care to have the product checked before use ever place the product and accessories her heat sources o the ventilation slots or other openings on the product Where the mains plug or an appliance coupler is used as the disconnect device shall remain readi device the disconnect y operable Disconnect the product from the power outlet before lightning storms When you disconnect pull the plug never the Risk of short circuit or fire Before you connect the he power cord always cable product to the power outlet ensure that the power voltage matches the value printed on the back or bottom of the product Never connect the product to the power outlet if the voltage is different Risk of injury or damage to the home theater For wall mountable products use only the supplied wall moun bracket Secure the wall mount to a wall that can support the combined weight of the product and the wall mount Koninklijke Philips Electronics N V bears no responsibility for improper wall mounting that results in accident injury or damage For speakers with stands use only the supplied stands Secure the stands to the sp
19. devices e System Audio Control System audio control If system audio control is enabled the audio of the connected device is output through your home theater speakers automatically when you play the device Audio Input Mapping Audio input mapping If system audio control does not work map the connected device to the correct audio input connector on your home theater see Set up the audio on page 10 Note To change the EasyLink control settings press SETUP select Video Setup gt HDMI Setup gt EasyLink Setup 10 EN Set up the audio If you cannot hear the audio output of a connected device through your home theater speakers check that you have enabled Easylink on all the devices see Enable EasyLink on page 10 Then set up the EasyLink audio control Press SETUP 2 Select Video Setup and then press OK 3 Select HDMI Setup gt EasyLink Setup gt System Audio Control gt On To play the audio from the TV speakers select Off and then skip the following steps Select EasyLink Setup gt Audio Input Mapping 5 Follow the onscreen instructions to map the connected device to the audio inputs on your home theater If you connect your home theater to the TV through an HDMI ARC connection make sure that the TV audio is mapped to the ARC input on your home theater 4 Use your home theater This section helps you use the home theater to play media
20. disc compartment is closed and there is no disc inside N Switch your TV to the correct source for your home theater Follow the onscreen instructions to confirm the update Once complete the home theater automatically switches off and restarts If it does not disconnect the power cord for a few seconds and then reconnect tt 7 Product specifications Note Specifications and design are subject to change without notice Region codes The type plate on the back or bottom of the home theater shows which regions it supports Country DV Europe United Kingdom Asia Pacific Taiwan Korea Latin America Australia New Zealand Russia India China Gl opoe Media formats DVD Video DVD R RW DVD R RW DVD R R DL CD R CD RW Audio CD Video CD SVCD Picture files MP3 media WMA media DivX media USB storage device File formats e Audio mp3 wma Video divx mpg mpeg e Picture jpg jpeg Amplifier e Total output power 1000W RMS 0 5dB 30 THD Frequency response 20 Hz 20 kHz 3 dB Signal to noise ratio gt 65 dB CCIR A weighted e Input sensitivity e AUXT AUX2 1 V Music iLink 350 mV Video Signal system PAL NTSC e HDMI output 480i 576i 480p 576p 720p 1080i 1080p Audio S PDIF Digital audio input Coaxial IEC 60958 3 Optical TOSLINK Sampling frequency
21. e 32 kHz 44 1 kHz 48 kHz e WMA 44 1 kHz 48 kHz Constant bit rate e 32 kbps 320 kbps e WMA 48 kbps 192 kbps Radio Tuning range Europe Russia China FM 87 5 108 MHz 50 kHz Asia Pacific Latin America FM 87 5 108 MHz 50 100 kHz Signal to noise ratio FM 50 dB Frequency response FM 180 Hz 12 5 kHz 3 dB Compatibility Hi Speed USB 2 0 e Class support USB Mass Storage Class MSC File system FAT16 FAT32 EN 19 English Main unit e Power supply Europe China Russia India 220 240 V 50 Hz Latin America Asia Pacific 110 127V 220 240V 50 60 Hz e Power consumption 105 WV Standby power consumption lt 0 5 W Dimensions WxHxD 435 x 56 x 344 mm Weight 3 0kg Subwoofer mpedance 4 ohm Speaker drivers 165 mm 6 5 woofer Dimensions WxHxD 178 x 303 x 343 mm Weight 3 84 kg Speakers Center speaker Speaker impedance 4 ohm Speaker drivers 1 x 76 2 mm 3 woofer Dimensions WxHxD 223 x 101 5 x 93 5 mm Weight 0 6 kg Front Rear speaker Speaker impedance 4 ohm Speaker drivers 1 x 76 2 mm 3 woofer Dimensions WxHxD Speakers 90 x 185 x 105 5 mm Tall speakers 247 x 1091 x 242 mm Weight Speakers 0 54 kg each Tall speakers 2 19 kg each Remote control batteries 2 x AAA RO3 1 5 V Laser Type Semiconductor laser GaAlAs CD Wave length 645
22. e TV through composite video Basic quality video If your TV does not have HDMI connectors use a composite video connection A composite connection does not support high definition video Using a composite video cable connect the VIDEO connector on your home theater to the VIDEO IN connector on the TV The composite video connector might be labeled AV IN COMPOSITE or BASEBAND 2 Connect an audio cable to hear the TV audio through your home theater see Connect audio from TV and other devices on page 8 3 When you watch TV programs press SOURCE on your home theater repeatedly to select the correct audio input 4 When you watch videos switch your TV to the correct video input For details see the TV user manual VIDEO OUT Connect audio from TV and other devices Play audio from TV or other devices through your home theater speakers Use the best quality connection available on your TV home theater and other devices Note The audio connections in this user manual are only recommendations You can use other connections too When your home theater and TV are connected through HDMI ARC an audio connection is not required Option 1 Connect audio through a digital optical cable Best quality audio Using an optical cable connect the OPTICAL connector on your home theater to the OPTICAL OUT connector on the TV or other device he digital optical connector
23. eakers tightly Place the assembled stands on flat level surfaces that can support the combined weight of the speaker and stand Never place the product or any objects on power cords or on other electrical equipment EN Risk Risk Risk f the product is transported in temperatures below 5 C unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet Visible and invisible laser radiation when open Avoid exposure to beam Do not touch the disc optical lens inside the disc compartment Parts of this product can be made of glass Handle with care to avoid injury and damage of overheating ever install this product in a confined space Always leave a space of at least four inches around the product for ventilation Ensure curtains or other objects never cover the ventilation slots on the product of contamination Do not mix batteries old and new or carbon and alkaine etc Danger of explosion if batteries are incorrectly replaced Replace only with the same or equivalent type Remove batteries if they are exhausted or if the remote control is not to be used for a long time Batteries contain chemical substances they should be disposed of properly of swallowing batteries The product remote control may contain a coin button type battery which can be swallowed eep the battery out of reach of children at all imes If swallowed the battery can ca
24. from a wide range of sources Before you start Make the necessary connections described in the quick start guide and the user manual e Switch the TV to the correct source for your home theater for example HDMI AV IN Discs Your home theater can play DVDs VCDs and CDs It can also play discs that you ve made at home such as CD R discs of photos and music Insert a disc into the home theater 2 Ifthe disc does not play automatically press DISC 3 Use the remote control to control play Play buttons REPEAT Select or turn off repeat mode REPEAT Mark two points within a chapter or track to repeat play or turn off the repeat mode ANGLE Select video scenes recorded in different camera angels G INFO Access the advanced options when you play your audio video or media files see Audio video and picture options on page 13 Synchronize picture and sound If the audio and video are not synchronized delay the audio to match the video 1 while playing video press and hold AUDIO SYNC Audio sync menu is displayed 2 Press the or Navigation buttons to synchronize the audio with the video and then press OK Note Button Action Navigation Navigate menus Picture and sound can be synchronized rough buttons Up Down the setup menu of your home theater press Video Slaw backward SETUP select Audio Setup
25. hat are connected through HDMI can be controlled by a single remote control Note Depending on the manufacturen HDMI CEC is known by many names For information on your device see the user manual of the device Philips does not guarantee 100 interoperability with all HDMI CEC devices Before you start Connect your home theater to the HDMI CEC compliant device through HDMI connection Make the necessary connections described in the quick start guide and then switch the TV to the correct source for your home theater EN 9 English Enable EasyLink 1 Press SETUP Select Video Setup and then press OK 2 3 Select HDMI Setup gt EasyLink Setup gt EasyLink gt On 4 On your TV and other connected devices turn on HDMI CEC control For details see the user manual of the TV or other devices e On your TV set the audio output to Amplifier instead of TV speakers For details see the TV user manual EasyLink controls With EasyLink you can control your home theater TV and other connected HDMI CEC compliant devices with a single remote control OneTouch Play One touch play When a video disc is in the disc compartment press gt IE to wake up the TV from standby and then play a disc e One Touch Standby One touch standby one touch standby is enabled your home theater can switch to standby with the remote control of the TV or other HDMI CEC
26. lution of the video signal being output from the HDMI OUT e Picture Settings Select color settings for the video display on TV HD JPEG Enable or disable high definition picture display Note f you change setting make sure that the TV supports the new setting Audio settings 1 Press SETUP 2 irs Audio Setup and then press OK HDMI Audio HDMI audio is automatically down mixed to two channel for TV speakers If you do not want to output audio through your TV disable the HDMI audio Night Mode Select quiet or full dynamic sound Night mode decreases the volume of loud sounds and increases volume of sounds such as speech Applicable to Dolby Digital encoded DVD discs only Parental control settings Password and Ratings 1 Press SETUP 2 Select Preference Setup and then press OK e Password Set or change your password for parental control access If you do not have a password or have forgotten your password enter 0000 Parental Enable maturity based restricted access for playback of DVD video that are recorded with ratings To play discs irrespective of the rating select 8 Adult Lock disc 1 Press SETUP 2 Select General Setup and then press OK e Disc Lock Lock the disc to restrict play You can lock up to 20 discs on your home theater Note To play a locked disc follow the onscreen instructions to enter the passwor
27. might be labeled SPDIF or SPDIF OUT OPTICAL IN Option 2 Connect audio through a digital coaxial cable Good quality audio Using a coaxial cable connect the COAXIAL connector on your home theater to the COAXIAL DIGITAL OUT connector on the TV or other device he digital coaxial connector might be labeled DIGITAL AUDIO OUT DIGITAL IN COAXIAL IN Option 3 Connect audio through analog audio cables Basic quality audio Using an analog cable connect the AUX connectors on your home theater to the AUDIO OUT connectors on the TV or other device AUX IN AUDIO IN Set up speakers Set up the speakers manually to experience customized surround sound Before you start Make the necessary connections described in the quick start guide and then switch the TV to the correct source for your home theater 1 Press SETUP on your home theater remote control 2 Select Audio Setup and then press OK 3 Press the Navigation buttons and OK to select and change Speakers Volume Set the volume level of each speaker Speakers Delay Set the delay time for speakers which are placed closer to the seating position in order to obtain equal audio transmission from all the speakers Set up EasyLink HDMI CEC control This home theater supports Philips EasyLink which uses the HDMI CEC Consumer Electronics Control protocol EasyLink compliant devices t
28. oftware EB Caution Do not install a lower version of software than the current version installed on your product Philips is not liable for problems caused due to software downgrade Check software version Check the version of the current software installed on your home theater 1 Press SETUP 2 Select Preference Setup and then press OK 3 Select Version Info and then press OK The software version is displayed 18 EN Update software through USB What you need e USB flash drive that is FAT formatted with at least 75MB of memory Do not use a USB hard drive e A computer with Internet access e Anarchive utility that supports the ZIP file format Step 1 Download the latest software 1 Connect a USB flash drive to your computer 2 m your web browser go to www philips com support 3 Athe Philips Support website find your product and locate the Software and drivers The software update is available as a zip file Save the zip file in the root directory of your USB flash drive Use the archive utility to extract the software update file in the root directory Os Disconnect the USB flash drive from your computer Step 2 Update the software Caution Do not switch off the home theater or remove the USB flash drive during the update Connect the USB flash drive containing the downloaded file to your home theater Make sure that the
29. r TV is HDMI ARC compliant you can hear the TV audio through your home theater by using a single HDMI cable Using a High Speed HDMI cable connect the HDMI OUT ARC connector on your home theater to the HDMI ARC connector on the TV The HDMI ARC connector on the TV might be labeled differently For details see the TV user manual 2 on your TV turn on HDMI CEC operations For details see the TV user manual Ifyou cannot hear the TV audio through your home theater set up the audio manually see Set up the audio on page 10 HDMI OUT ARC EN 7 English Option 2 Connect to TV through standard HDMI Best quality video If your TV is not HDMI ARC compliant connect your home theater to the TV through a standard HDMI connection 1 Using a High Speed HDMI cable connect the HDMI OUT ARC connector on your home heater to the HDMI connector on the TV 2 Connect an audio cable to hear the TV audio hrough your home theater see Connect audio from TV and other devices on page 8 3 On your TV turn on HDMI CEC operations For details see the TV user manual e Ifyou cannot hear the TV audio through your home theater set up the audio manually see Set up the audio on page 10 e f your T V has a DVI connector you can use HDMI DVI adapter to connect to TV However some of the features may not be available HDMI OUT Option 3 Connect to th
30. s the following file formats srt sub txt ssa ass smi and sami If the subtitles do not appear correctly change the character set 1 while playing video press SUBTITLE to select a language 2 For Divx video if the subtitles do not appear correctly continue the following steps to change the character set Press SETUP Select Preference Setup and then press OK Select DivX Subtitle and then select a character set that supports the subtitle Un 43 Ww Character Set Standard Language English Albanian Danish Dutch Finnish French Gaelic German Italian Kurdish Latin orwegian Portuguese Spanish Swedish and Turkish Albanian Croat Czech Dutch English German Hungarian rish Polish Romanian Slovak Slovene and Sorbian Central Europe Cyrillic Bulgarian Belorussian English acedonian Moldavian Russian Serbian and Ukrainian Greek Greek Hebrew Hebrew Chinese Simp Simplified Chinese 12 EN VOD code for DivX Before you purchase DivX videos and play them on your home theater register the home theater www divx com using the DivX VOD code Press SETUP Select General Setup and then press OK Select DivX R VOD Code and then press OK Press OK again The DivX VOD registration code for your home theater is displayed N USB storage devices Enjoy pictures audio and video stored on a USB storage device
31. settings 16 lock disc 17 main unit overview 4 menu language for discs 16 MP3 player 14 musical slideshow 13 night mode 16 one touch play 10 one touch standby 10 onscreen menu language 16 parental control 7 parental ratings 7 password 7 PBC play back control 7 picture options 3 picture settings 6 product serial number 3 program radio stations 4 radio 14 recycling 3 remote control overview 5 repeat mode 11 restore default settings 17 rotate pictures 11 EN 23 English 5 screen saver setup menu 6 sleep timer 7 slideshow 3 sound mode S speakers placement 6 speakers setup 9 specifications 9 subtitle language for discs 6 supported file format 9 supported media formats 9 surround sound 5 synchronize picture and sound 1 system audio control 0 T time search 13 titles 13 trademarks 22 troubleshooting 20 U update software 18 USB storage device 12 V video options 13 video resolution 16 VOD code for DivX 12 W wireless rear audio 7 24 EN Language Code Abkhazian 6566 Afar 6565 Afrikaans 6570 Amharic 6577 Arabic 6582 Armenian 7289 Assamese 6583 Avestan 6569 Aymara 6589 Azerhaijani 6590 Bahasa Melayu 7783 Bashkir 6665 Belarusian 6669 Bengali 6678 Bihari 6672 Bislama 6673 Bokmal Norwegian 7866 Bosanski 6683 Brezhoneg 6682 Bulgarian 6671 7789 Castellano 6983 Catal n 6765 Chamorro 6772 Chechen 6769 Chewa Chichewa Nyanja 7889 9072 Chuang Zhuang
32. sit divx com for more information and software tools to convert your files into DivX videos ABOUT DIVX VIDEO ON DEMAND This DivX Certified device must be registered in order to play purchased DivX Video on Demand VOD movies To obtain your registration code locate the DivX VOD section in your device setup menu Go to vod divx com for more information on how to complete your registration HDMI and HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United States and other countries CLASS 1 LASER PRODUCT 10 Index A audio from TV and other devices 8 audio input mapping 10 audio language for discs 16 audio options 13 auto standby 17 B batteries 20 C change password 17 character set 12 check current version 18 connect analog audio cable 9 connect coaxial audio cable 9 connect coaxial audio cable 9 connect composite video cable 8 connect FM antenna 4 14 connect HDMI cable 7 8 connect home theater 6 connect optical audio cable 8 connect speakers 6 connect to TV 7 connectors 4 consumer support 3 control play buttons 11 create MP3 14 D disc menu 16 discs 11 display brightness 17 display menu for MP3 JPEG 17 display menu for VCD SVCD 17 disposal 3 DivX 12 19 DivX subtitles 12 E Easylink HDMI CEC 9 Easylink audio setup 10 Easylink controls 10 H HDMI ARC 7 HDMI video 16 HDMI CEC 9 language
33. such as an MP4 player or digital camera What you need A USB storage device that is formatted for FAT file system and complies with the Mass Storage Class Note f you use a USB extension cable USB HUB or USB multi reader the USB storage device may not be recognized You can connect to a digital camera if they can play the files without using a special computer program Connect a USB storage device to the amp USB connector on your home theater Press USB A content browser is displayed Select a file and then press OK AW N Use the play buttons to control play see Play buttons on page 11 Audio video and picture options Use advanced features when you play pictures audio and video files from a disc or a USB storage device Audio options For CDDA 1 Press D INFO repeatedly to cycle through the following options Show the current track information and time Disc Go To Enter the disc time to skip to a specific part of the disc Track Go To Enter the track time to skip to a specific part of the track Select Track Select a specific track For MP3 Press INFO to display the remaining time of the current track 2 Press INFO again to enter track time mode and then press the Numeric buttons to input the track time Video options 1 Press INFO The video options menu is displayed Depending on the video source some options
34. ti channel mode will output 5 channel stereo sound EN 15 English 5 Change settings The home theater settings are already configured for optimal performance Unless you have a reason o change a setting we recommend that you keep he default setting You cannot change a setting that is grayed out To return to the previous menu press 2 BACK To exit the menu press SETUP Language settings Onscreen display language 1 Press SETUP 2 Select General Setup and then press OK OSD Language Select a display language for menu Disc language 1 Press SETUP Select Preference Setup and then press OK e Audio Select an audio language for discs Subtitle Select subtitle language for discs Disc Menu Select a menu language for discs Note f your preferred disc language is not available select Others from the list and enter the 4 digit language code found at the end of this user manual f you select a language that is not available on a disc the home theater uses the default language of the disc 16 Picture and video settings 1 Press SETUP 2 Select Video Setup and then press OK TV System Select a video format supported by the TV Display Select a picture format to fit the TV screen HDMI Setup Wide Screen Format For 16 9 wide screen TV display setting HDMI Video Select the reso
35. to the TV Sound No sound from home theater speakers Connect the audio cable from your home theater to your TV or other devices see Connect audio from TV and other devices on page 8 Set up the audio for the connected device for HDMI connection only see Set up the audio on page 10 Reset your home theater to its factory settings see Restore default settings on page 17 then switch it off and switch on again On your home theater press SOURCE repeatedly to select the correct audio input Distorted sound or echo If you play audio from the TV through the home theater make sure that the TV is muted Audio and video are not synchronized 1 Press and hold AUDIO SYNC 2 Press the or Navigation buttons within 5 seconds to synchronize the audio with the video Play Cannot play a disc Cannot play a DivX file Clean the disc Make sure that the home theater supports he type of disc see Media formats on page 19 Make sure that the home theater supports he region code of the disc f the disc is DVDXRW or DVDR disc make sure that it is finalized Make sure that the DivX file is encoded according to the Home Theater Profile with he DivX encoder Make sure that the DivX file is complete DivX subtitles do not display correctly Cannot read the contents of a USB storage device Make sure that the subtitle file name is the same as the movie file name see
36. turn off repeat mode e In radio mode press once to access program mode and press again to store the radio station n radio mode press and hold for three seconds to reinstall the radio stations REPEAT A B Mark two points within a chapter or track to repeat play or turn off the repeat mode EN 5 down to slow backward or slow forward English 5 CREATE MP3 ZOOM e Access the create menu e Zoom into a video scene or picture Press the Navigation buttons left right to select a zoom factor EB SCREEN FIT Fit the picture format to the TV screen 7 SUBTITLE Select subtitle language for video AUDIO SYNC Select an audio language or channel Press and hold to access audio delay setting and then press the or Navigation buttons to delay the audio to match the video SURR Select surround sound or stereo sound E Stop Stop play In radio mode press and hold to erase the current preset radio stations Q1 gt IH Play Pause Start pause or resume play Q3 WINFO Access more play options while playing a disc or a USB storage device Q3 SETUP Access or exit the setup menu SLEEP Switch the home theater to standby mode after the elapsed time 3 Connect and set up This section helps you connect your home theater to a TV and other devices and then set it up For information about the basic connections of your home theater and accessories see the quick start guide
37. use serious injury or death Severe internal burns can occur within two hours of ingestion f you suspect that a battery has been swallowed or placed inside any part of the body seek immediate medical attention When you change the batteries always keep all new and used batteries out of reach of children Ensure that the battery compartment is completely secure after you replace the battery If the battery compartment cannot be completely secured discontinue use of the product Keep out of reach of children and contact the manufacturer Care for your product Do not insert any objects other than discs into the disc compartment Do not insert warped or cracked discs into the disc compartment Remove discs from the disc compartment if you are not using the product for an extended period of time e Use only microfiber cloth to clean the product Care of the environment ab Your product is designed and manufactured with high quality materials and components which can be recycled and reused A When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your
Download Pdf Manuals
Related Search