VIVOTEK AE-235
Contents
1. 6 Pan and tilt the enclosure to aim at the monitored area Ethernet cable Power cord 7 Mount the enclosure to the mounting plate C with supplied four screws 8 Use the supplied long screw to secure C with B 9 Use the supplied big screw to secure B with A 10 Use the supplied three screws to mount the enclosure to a desired location2. AE 235 Infrared Illuminator Enclosure Installation Guide Rev 1 0 CAUTION TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL UNPACKING Unpack carefully Electronic components can be damaged if improperly handled o dropped If an item appears having been damaged in shipment place it properly in its carton and notify the shipper and followed before the unit is to be operated 2 Electrical Connections Only a qualified electrician allow to make electrical 1 Read and follow Instructions All operating and user instructions should be read connections Specifications Model Name AE 235 AC90 240V 10 Rating Current Heater Control 18 C ON 28 C OFF amp 0 C ON 10 C OFF Blower Control 35 C ON 25 C OFF 20 C 50 C 40 C 50 C IP68 or IP44 with ventilation hole Temper glass 4mm thickness on gt Operation Temp Environmental Storage Temp Protection Level Mounting Bracket Fully cable Management Construction Die Cast Aluminum Alloy Coating Ivory Powder amp Stove Finish 425 L x 160 W x 165 H mm 275 L x 90 W x 100 H mm 5530 gm Dimensions Camera Space Net Weight fl Physical description Lens cap with heater IR LEDs behind temper glass IR board and IR board bracket Thermostat switch Day Night trigger controls the color mono Universa
3. al status High Low Network Current status Low Security Digital output PTZ Normal status Open Grounded Event Current status Open Applications Save Motion detection DI and DO Tampering detection Day Night settings i Configure the camera s IR cut filter RT ER setting if your camera comes with it to 7 Turn on external IR illuminator in night mode Synchronize with digital input IR cut filter Auto mode Auto mode i i Light sensor sensitivity Day mode The configuration option can be found Night mode in Configuration gt Media gt Image gt Schedul d i Color BIW Color General settings gt Day Night settings gt Power line frequency 50 Hz 60 Hz IR cut filter 0 Hardware Installation 1 Loosen two screws on both sides of the camera bracket and then adjust the position of camera bracket by sliding it up and down 2 Use the supplied L type hex key wrench to fix the camera on the camera bracket 3 Connect the power cable and Ethernet cable to the camera Side View L type hex key wrench i CLI f N J j I English 4 Assemble the mounting bracket arm A B C 110 00mm WW00 S6 8 00mm Dimensions of Bracket Base 5 Feed the Ethernet cable and power cord from hole D on the bottom of the enclosure through the mounting bracket arm
4. l IR control circuit board to mode switch for D N cameras control color mono switching and IR on off synchronization Power Supply Unit AC90 240V power input DC12V output power input 3 OUTPUT_1 spare terminal block for AC 24V or AC 90 240V camera use VR to adjust the Infrared LED activation level 16 Thermostat switch turn on at 35 C and turn off at 25 C for blower 3 Camera bracket ol Ei English AC input wiring connect power lines to an external power cord Power cords Connector Block Brown Line Blue Neutral Yellow Green Earth Once a camera is installed you can connect the 12V DC phone jack connector to power the camera Since the housing comes with a light sensor which controls when to turn into the night mode and light the IR LEDs Connect the red or orange wire to the DI pin on the terminal block and the black wire to the Ground pin The following determines which wire Red or Orange should be connected to the DI pin Red If IR trigger signal is on the high position 5V DC connect the Red and Black wires Orange If IR trigger signal is on the Low position OV DC connect the Orange and Black wires You should check the DI and Do settings on a web console in Configuration gt Applications gt DI and DO For example if you connect the Red line to the DI its normal status should be High Applications gt DI and DO seem Digital input Media Norm
Download Pdf Manuals
Related Search