Snow Joe Pressure Joe SPX3000
Contents
1. 6 Connect the PVC detergent tube to the detergent connection Fig 7 7 To assemble the spray wand protector snap the tab into the slot located at the bottom left side of the unit and secure it in place with small screw Figs 8 amp 9 8 To assemble the hose holder slide the holder into position Figs 10 amp 11 and secure it to the unit with remaining small screw Fig 12 9 Fit the spray wand into the gun and rotate it until the two parts are completely locked Fig 13 Fig 13 10 Connect the high pressure hose to the trigger gun Fig 14 Fig 14 Trigger gun High Pressure Hose 11 Connect the high pressure hose to the water outlet on the washer Fig 15 a REAR Fig 15 High pressure hose High pressure water outlet N WARNING Keep hose away from sharp objects Bursting hoses may cause injury Examine hoses regularly and replace if damaged Do not attempt to mend a damaged hose 12 Connect the garden hose adaptor female coupler to the water inlet of the pressure washer then thread your garden hose male end into the garden hose adaptor Fig 16 The garden hose must have an internal diameter of at least 13 mm 1 2 in and must be reinforced T2. 2030 PSI 1775 Ge P Model No SPX3000 A Division of Snow Joe LLC IMPORTANT Safety Instructions All Operators Must Read These Instructions Before Use Safety Alert Symbols Always follow these safety guidelines Failure to do so may result in serious bodily injury or death N WARNING This indicates a hazardous situation which if not avoided could result in death or serious injury Z cauTIon This indicates a hazardous situation which if not avoided could result in minor or moderate injury Z DANGER This indicates a hazardous situation which if not followed will result in death or serious injury Safety Rules N WARNING This appliance is not intended for use by children or by unassisted unsupervised persons whose physical sensory or mental capabilities prevent them from using it safely Children should be supervised to ensure that they do not play with the appliance Before starting up your machine please check it carefully for any defects If you find any do not start up your machine and contact your distributor N WARNING When using the pressure washer basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following e Know your product Know how to stop the machine and bleed pressure quickly Be thoroughly familiar with the controls e Keep bystanders away All visitors and pets should be kept a safe distance a
3. Release trigger and engage the gun safety lock N WARNING Turn off the water supply and squeeze the trigger to depressurize the unit Failure to do so could result in personal injury due to discharge of high pressure water Taking a break If you are taking a break of five minutes or more between cleaning tasks 11 e Engage the gun safety lock e Turn the switch to the OFF 0 position e Unplug the power cord from the outlet Storage N CAUTION Always store your pressure washer in a location where the temperature will not fall below 32 F 0 C The pump in this machine is susceptible to permanent damage if frozen FREEZE DAMAGE IS NOT COVERED BY THE WARRANTY e Store in a dry covered area where the weather cannot damage the machine e t is important to store this product in a frost free area e Always empty water from all hoses the pump and the detergent containers before storing Z caution The use of a pump protector is recommended to prevent cold weather damage during storage over the winter months Winterizing and long term storage If you must store your pressure washer in a location where the temperature is below 32 F 0 C you can minimize the chance of damage to your machine by utilizing the following procedure e Disconnect all water connections e Turn on the machine for a few seconds until the remaining water in the pump exits Turn off immediately e Do not allow the high pressure hose to become
4. by the manufacturer or his service agent or similarly qualified person in order to avoid a hazard e Keep the machine on a stable flat surface during operation handling transportation and storage Sudden overturn of the machine can cause bodily injury e In the event of an accident or breakdown switch off the machine immediately If contact with detergent occurs rinse with an abundance of clean water Electrical Safety ATTENTION If there are problems with the electrical MAINS short voltage drops may appear when starting the equipment This can in turn influence other equipment e g cause a lamp to blink If the MAINS IMPEDANCE Zmax lt 0 335 OHM such disturbances are not expected In case of assistance contact your local supply authority for further information N WARNING Electrical Shock Hazard Before starting up your machine please check it carefully for any defects If you find any do not start up your machine and contact your distributor The following should be observed when connecting the high pressure washer to the electric installation e The electric supply connection should be performed by a qualified person e The electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to the earth exceeds 30 mA for 30 ms or a device that will interrupt the earth circuit GFCI IMPORTANT Only use water without any impurities If t
5. into 5 L 1 gallon of fresh water Siphon water at low pressure for one minute so that all the detergent is flushed through the system Remove the detergent bottle and rinse it until it is thoroughly cleaned Fig 26 Rinsing with pressure washer Z caution Failure to follow these cleaning instructions will cause the injection system to become clogged and inoperable e Turn off the pressure washer and shut off the water supply e Pull the trigger to release water pressure e Engage the safety lock on the trigger handle by pushing up on the safety lock until it clicks into the slot Fig 22 e Remove the nozzle by placing your hand over the nozzle while pulling back on the quick connect collar e Select the right nozzle for the job Fig 26 i A 0 straight pencil point nozzle orange is a thin extremely powerful nozzle used to cut heavy deposits in a small concentrated area It is ideal for dissolving stubborn substances like tar and grease spots on concrete or caked mud from equipment Use this nozzle to clean hard to reach areas including the facades of 2 story buildings or the undersides of lawn mowers tractors NOTE Care should be used to avoid gouging wood or damaging fragile surfaces ii Use the 15 fan tip nozzle yellow for intense cleaning jobs on hard surfaces Applications include stripping paint removing oil stains grease heavy mildew stains and rust from steel This nozzle sh
6. kinked e Store the machine and accessories in a room that does not reach freezing temperatures e Do not store near a furnace or other sources of heat that may dry out the pump seals e Operate the washer with non corrosive non toxic antifreeze before storing for the winter N WARNING Before reusing completely flush the unit out with clear water Antifreeze can damage paintwork so you must ensure there is no antifreeze left in the system before using it again Maintenance Z cauTION Before working on the washer disconnect the plug from the power supply socket e To ensure good performance check and clean the water inlet filter Fig 27 Remove filter and rinse with warm water to prevent any foreign matter from clogging the pump Fig 28 Pig a7 FRONT Water inlet filter Garden hose adaptor Fig 28 Inlet filter ss SY e Clean the nozzle with the needle clean out tool provided Fig 29 Remove the spray wand from the gun remove any dirt from the nozzle hole and rinse Fig 29 Needle clean out tool e Remove additional debris by back flushing water through the nozzle To do this place the end of your garden hose with water running to the tip of nozzle pushing water and debris out the back opening of the spray wand Circuit Diagram A circuit diagram for the pressure washer is provided below for your reference Fig 30 Fig
7. wand e Quick connect 0 15 25 40 and soap nozzles e Removable detergent tanks 2 e 4 long screws e 2 small screws e Spray wand protector e Trigger gun holder e Hose holder e Needle clean out tool e High pressure hose e Garden hose adaptor female coupler with two sealing rings 1 Carefully remove the contents from the shipping carton Make sure that all items listed in the carton contents are included 2 Inspect the product carefully to make sure no breakage or damage occurred during shipping If you find damaged or missing parts DO NOT return to the store Please call 1 866 766 9563 NOTE Do not discard the shipping carton and packaging material until you are ready to use your new Electric Pressure Washer Assembly 1 Position the washer as CLOSE as possible to the water supply 2 The washer must be used on a secure and stable surface in a standing upright position Fig 1 3 Slide the trigger gun holder into position Fig 2 Fig 2 4 Slide the handle into position and secure it with 4 long screws Fig 3 Fig 3 Fig 1 X qi a I a 5 Insert the detergent bottles top end first under the ridge of their designated storage compartment Figs 4 amp 5 Then snap the bottom of the bottles into the V shaped grooves to secure them in place Fig 6 Fig 4 QUO Oe O
8. 30 Micro switch S Power cord Motor On off switch Capacitor Disposal Recycling the washer e Do not dispose of electrical appliances as unsorted municipal waste Use separate collection facilities e Contact your local government agency for information regarding the collection systems available e lf electrical appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain damaging your health and well being e When replacing old appliances with new ones the retailer is legally obligated to take back your old appliance for disposal at least free of charge Service and Support If your Electric Pressure Washer requires service or maintenance please call 1 866 766 9563 for assistance Model and Serial Numbers When contacting the company or reordering parts you will need to provide the model and serial numbers of your product These are found on the decal affixed to the housing or guard of your Electric Pressure Washer Copy these numbers into the space provided below Record the following numbers from the housing or handle of your new product Model S P X 3 0 0 0 Serial 12 Troubleshooting e Disconnect the unit from the electrical power supply b
9. 766 9563 Snow Joe LLC may from time to time change the design of its products Nothing contained in this warranty shall be construed as obligating Snow Joe LLC to incorporate such design changes into previously manufactured products nor shall such changes be construed as an admission that previous designs were defective This warranty is intended to cover product defects only Snow Joe LLC is not liable for indirect incidental or consequential damages in connection with the use of the Snow Joe Products covered by this warranty This warranty does not cover any cost or expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non use of this product while waiting for completion of repairs under this warranty Some states do not allow exclusions of incidental or consequential damages so the above exclusions may not apply in all states This warranty may give you specific legal rights in your state If you wish to contact Snow Joe please direct inquiries to the Customer Service Department Snow Joe Center 86 Executive Avenue Edison NJ 08817 Customers who have purchased Snow Joe products exported from the United States and Canada should contact their Snow Joe Distributor Dealer to obtain information applicable for your country province or state If for any reason you are not satisfied with the distributor s service or if you have difficulty obtaining warranty in
10. d using long thin hoses min 1 2 in e Clean the nozzle e Nozzle partially blocked e Water filter blocked e Hose kinked e Clean the filter e Straighten out hose Machine often starts e Pump spray gun is leaking e Please call 1 866 766 9563 for assistance and stops by itself Machine starts but e Pump hoses or accessories frozen e Wait for pump hoses or accessories to thaw no water comes out e No water supply e Connect inlet water e Water filter blocked e Clean the filter e Nozzle blocked e Clean the nozzle 13 A Two Year Full Warranty for residential use in the United States and Canada General Conditions Snow Joe LLC warrants this product to the original purchaser for two years against defects in material or workmanship when used for normal residential purposes Snow Joe LLC will repair any defect in material or workmanship and repair or replace any defective part subject to the conditions limitations and exclusions set forth herein Such repair or parts replacement will be free from charge to the original purchaser except noted below The duration of the warranty applies only if the product is put to personal use around the household or residence If the product is put to any business use commercial or industrial then the duration of this warranty is 90 days from the date of original purchase If any product is rented or leased the duration of the warranty is 90 days from the date of
11. e To ensure appliance safety use only original replacement parts from the manufacturer or approved by the manufacturer SAVE THESE INSTRUCTIONS N WARNING Water that has flown through backflow preventers is considered to be non potable N WARNING During cleaning maintenance or when replacing parts the machine must be disconnected from its power source by removing the plug from the socket outlet N WARNING High pressure hoses fittings and couplings are important for the safe operation of the appliance Use only hoses fittings and couplings recommended by the manufacturer e Check for damaged parts Do not use the appliance if the supply cord or other important parts of the appliance are damaged e g safety devices high pressure hoses trigger gun N WARNING If an extension cord is used the plug and socket must be of watertight construction N WARNING Inadequate extension cords can be dangerous e This high pressure washer must not be used at temperatures below 32 F 0 C N WARNING Power cords on drums should always be completely unwound to prevent the cord from overheating e Power cord connections should be kept dry and off the ground e Comply with the below requirements for length and cord specs Table 1 Total length of cord in feet 120V Ampere Rating More than Not more than 0 6 16 14 6 10 14 10 12 12 Not Recommended e f the power cord is damaged it must be replaced
12. e the life of the pump Store indoors NEVER store the pressure washer outdoors or where it could freeze The pump will be seriously damaged e Ground Fault Circuit Interrupter GFCI Protection should be provided on the circuits or outlets to be used for this pressure washer Receptacles are available having built in GFCI protection and may be used for this measure of safety The insulation of the power cord should be faultless and without any cracks If the power cord is damaged an authorized distributor should replace it N WARNING Do not use this appliance without reading this instruction manual N WARNING This appliance has been designed for use with cleaning agents that are recommended by the manufacturer The use of other cleaning agents or chemicals may adversely affect the safety of the appliance N WARNING Do not use the appliance within range of persons unless they are wearing protective clothing N WARNING High pressure jets can be dangerous if subject to misuse The jet must not be directed at persons pets live electrical equipment or the appliance itself e Do not direct the jet against yourself or others in order to clean clothes or footwear e Risk of explosion Do not spray flammable liquids e Disconnect tool Disconnect from the electrical power supply before performing any maintenance task e Keep children away High pressure washer must not be used by children or untrained personnel
13. ection Risk of electrocution e Inspect cord before using e Do not use if cord is damaged e Keep all connections dry and off the ground e Do not touch plug with wet hands e Keep cord away from heat and sharp edges e Do not spray electrical apparatus and wiring Risk of explosion e Do not spray flammable liquids e Do not use acids bases solvents or any flammable material in this product These substances can cause physical injuries to the operator and irreversible damage to the machine Additional safety instructions e High pressure keep clear of nozzle e Injection hazard equipment can cause serious injury if the spray penetrates the skin e Do not point the gun at anyone or at any part of the body e In case of skin penetration seek medical aid immediately e Before servicing cleaning or removing any parts shut off the power and relieve pressure e This machine is not suitable for connection to the potable water mains Product Description Purpose e The high pressure cleaner is intended for residential use to clean vehicles machines buildings facades etc Areas of application e Never use the machine in potentially explosive areas under any circumstances e The operating temperature must be between 32 F 0 C and 104 F 40 C e The machine consists of an assembly with a pump which is encased in a shock absorbing housing To provide the operator with an optimal working position the mach
14. efore carrying out maintenance on the machine or when checking that its parts are in proper working order e To avoid unnecessary disappointments you should check the following before contacting the service organization Problems Possible Cause Possible Solution Machine refuses e Power failure machine not plugged e Check to make sure machine is plugged into to start into a working receptacle a working outlet e Defective socket e Replace fuse Switch off other machines e Fuse has blown e Try without the extension cord e Defective extension cord e Check the power cord and reset the GFCI Fluctuating pressure e Pump sucking air e Check the hoses and connections are airtight e Valves dirty worn out or stuck e Clean and replace or refer to local distributor e Pump seals worn out Machine stops e Fuse has blown e Check that the mains voltage corresponds to e Incorrect mains voltage specification on the model tag e Leave the washer for 5 minutes to cool down Clean the nozzle e Thermal sensor activated e Nozzle partially blocked Fuse blows e Fuse too small e Change to an installation higher than the amp consumption of the machine You may try without the extension cord Machine pulsating e Air in inlet hose e Allow machine to run with open trigger until regular e Inadequate supply of mains water working pressure resumes e Check that the water supply corresponds to specifications required e WARNING Avoi
15. fore operating the pressure washer Compare the illustration below to the pressure washer in order to familiarize yourself with the location of the various controls and adjustments Save this manual for future reference 1 Safety lock Locate lock in center of trigger Pull up and snap in place See Fig 12 pg 7 2 Trigger 3 Handle 4 High pressure hose connection 5 Trigger gun 6 Spray wand 7 Water inlet garden hose connection 8 Spray wand protector 9 High pressure hose 10 Garden hose adaptor female coupler 11 Needle clean out tool 12 0 quick connect nozzle orange 13 15 quick connect nozzle yellow 14 25 quick connect nozzle green 15 40 quick connect nozzle gray 16 Soap quick connect nozzle black 17 Detergent selection dial 18 Removable detergent tanks 19 Hose holder 20 On off switch 21 Power cord 22 Cord holder 23 Onboard storage for quick connect nozzles 24 Detergent tube 25 Trigger gun holder 26 Water outlet high pressure connection 27 NS _ 12 13 14 15 16 Technical Data Rated Voltage 120 V 60 Hz Rated Pressure 1450 PSI Motor 14 5 amp 1800 W Max Pressure 2030 PSI Max Water Inlet Temperature 104 F 40 C Hose Length 20 ft 6 m Max Water Inlet Pressure 0 7 MPa Power Cord Length 35 ft 10 7 m Max Rated Flow 1 76 GPM Weight 31 Ibs 14 kg Unpacking Carton Contents e Pressure washer unit e Handle e Manual e Trigger gun e Spray
16. formation contact your Snow Joe seller If in the event your efforts are unsatisfactory please write to the Snow Joe Center at the above address If you have any questions about your product warranty please call 1 866 SNOW JOE or visit us online at www snowjoe com 14
17. he water supply must be at least equal to the washer delivery capacity NOTE The machine is not suitable for connection to the portable water main FRONT Garden hose This end to male end water inlet Water inlet Fig 16 Garden hose female coupler 13 Attach garden hose to water supply Fig 17 Fig 17 Connect to water supply t HTH Garden hose N WARNING The intake water temperature must not exceed 104 F 40 C The water supply must not exceed 0 7 MPa N CAUTION The washer must only be used with clean water use of unfiltered water containing corrosive chemicals will damage the washer 14 Push the motor switch to the OFF 0 position Fig 18 15 Check that the electrical supply voltage and frequency Volt Hz correspond to those specified on the washer rating plate If the power supply is correct you may now plug the washer into the power outlet Fig 19 Fig 19 7 ee GFCI R Operation N IMPORTANT This pressure washer is equipped with a micro switch sensitive to water flow This Total Stop System TSS senses water flow in the pump When the trigger is released water stops flowing through the pump The TSS then automatically turns the motor off to protect the pump from overheating 1 Turn the water supply tap on completely 2 Push the safety lock down and into its origina
18. here is a risk of running sand into the inlet water i e from your own well an additional filter should be installed Safety devices The unloader valve can reduce pressure if it exceeds preset values The spray gun features a locking device When the lock is activated the spray gun cannot be operated e Thermal sensor A thermal sensor protects the motor against overloading The machine will restart after a few minutes when the thermal sensor has cooled e Double insulation In a double insulated product two systems of insulation are provided instead of grounding No grounding means are provided on a double insulated product nor should a means for grounding be added to the product Servicing a double insulated product requires extreme care and knowledge of the system and should be performed only by a qualified service person Replacement parts for a double insulated product must be identical to the parts they replace A double insulated product is marked with the words DOUBLE INSULATION or DOUBLE INSULATED The symbol G may also be marked on the product Ground Fault Circuit Interrupter GFCI This pressure washer is provided with a ground fault circuit interrupter GFCI built into the plug of the power supply cord This device provides additional protection from the risk of electric shock Should replacement of the plug or cord become necessary use only identical replacement parts that include GFCI prot
19. ine is equipped with a spray wand and a non slip handle grip whose shape and configuration comply with applicable regulations e Do not cover or modify the spray wand or the spray nozzles in any way e The high pressure washer is designed to be used with cold or lukewarm water higher temperatures can damage the pump e Do not use water that is dirty gritty or contains any chemical products as these could impair operation and shorten the life of the machine Safety Symbols The following table depicts and describes safety symbols that may appear on this product Read understand and follow all instructions on the machine before attempting to assemble and operate Description SAFETY ALERT indicates a precaution a warning or a danger READ THE OPERATOR S MANUAL S Read understand and follow all instructions in the manual s before attempting to assemble and operate WARNING Keep out of rain and away from wet areas For protection against injury wear safety goggles and ear protection Electrical shock hazard To reduce the risk of injury user must keep all bystanders at least 15 m away SWITCH OFF Remove plug from outlet immediately if the cord is damaged or cut Machine not suitable for connection to the potable water mains Sound power level is 96 dB A Double insulation Know Your Pressure Washer Read the owner s manual and safety rules carefully be
20. l position Fig 20 then press the trigger for a few seconds until water flow is steady to allow air to escape and to discharge residual pressure in the hose Fig 20 Safety lock 3 Keeping the trigger pressed turn the switch to the ON 1 position to start the pressure washer Fig 21 i Fig 21 ON OFF 0 2 Z 4 When re starting the motor always keep the trigger pressed NOTE The motor only runs when the trigger is engaged and shuts off when the trigger is released Using the nozzles Before beginning any cleaning task determine the best nozzle for the job Each of the nozzles has a different spray pattern The nozzle patterns are 40 for gentle cleaning 25 for all purpose cleaning 15 for tough jobs 0 for spot cleaning or hard to reach areas and the Soap Nozzle for detergent application Z caution NEVER change nozzles without locking the safety lock on the trigger handle N WARNING High pressure jets can be dangerous if subject to misuse The jet must not be directed at persons pets live electrical equipment or the appliance itself e To engage the safety lock pull the safety lock until it clicks into the slot Fig 22 Fig 22 Safety lock The washer is equipped with quick connect nozzles that easily snap onto the quick connect collar of the spray wand To connect a nozzle to the spray wand e Turn off the pressure washer and shut off the water supply Pull
21. original purchase It is the owner s responsibility to perform correctly all maintenance and minor adjustments explained in the owner s manual Electric Products To obtain a replacement electric powered unit or repair the existing electric powered unit you must return the complete unit and postage prepaid to Snow Joe Return Center 86 Executive Avenue Edison NJ 08817 Gasoline Battery Products Limitations e Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis Rechargeable batteries will be replaced free from charge during the first 90 days After the initial 90 days batteries will be replaced at a prorated cost to the customer e Idlers cables and electrical components are warranted to the original purchaser for use at household or residence for a period of two years Exclusions e Snow Joe brand engines are covered under this warranty All other engines and engine accessories are covered only by the engine manufacturer s warranty and are not covered by this warranty e Parts used that are not genuine Snow Joe parts are not covered by this warranty e Damages resulting from misuse alteration improper assembly improper adjustment neglect or accident which requires repair is not covered under this warranty e Belts augers and tines are not covered under warranty belts augers and tines wear out and can be purchased at www snowjoe com or by calling 1 866
22. ould only be used in areas that can withstand the high pressure from this nozzle iii Use the 25 fan tip nozzle green to clean home siding brick patios wood decks driveways or sidewalks When using this nozzle test a small area first to avoid surface damage Use the 40 wide spray tip nozzle gray to clean items such as cars trucks boats patio furniture or lawn equipment Use the soap nozzle black for low pressure detergent application to clean equipment remove mildew and oxidations stains from houses clean effervescent brick and degrease NOTE When using detergent make sure that the correct soap nozzle black is installed All of the other colored nozzles will not work for detergent application e Start at the top of the area to be rinsed and work down making sure to overlap the strokes A important NEVER USE e Bleach chlorine products and other corrosive chemicals e Liquids containing solvents e g paint thinners gasoline oils e Tri sodium phosphate products e Ammonia products e Acid based products e These chemicals will harm the unit and will damage the cleaning surface Shutting down 1 Turn the switch to the OFF 0 position and unplug the power cord from the outlet Turn off the water source 3 Press trigger to release water pressure 4 Disconnect the garden hose from the water inlet on the unit Disconnect the high pressure hose from the high pressure outlet 6
23. t bottle e Gently pull the on board detergent tanks out of their storage position and fill with detergent Fig 24 Fig 24 Detergent tank e Insert the suction tube with filter into the tank and cap the tank closed Push the tanks back into their storage position on the unit e Turn the detergent dial to the center O Fig 25 e Install the soap nozzle black on the spray wand Fig 26 Z caution Always test detergent in an inconspicuous area before use e Turn on the pressure washer Pull the trigger to operate the unit The liquid detergent will automatically mix with water and be discharged through the nozzle e Turn the detergent dial to adjust the suction volume of the detergent solution Fig 25 Detergent selection dial e Apply detergent from the bottom to the top of the DRY surface to be cleaned NOTE Wetting the surface first is not recommended as it dilutes the detergent and reduces its cleaning ability e Allow the detergent to remain on the surface for a short time before rinsing Do not allow the detergent to dry on the surface 10 N CAUTION Damage may occur to painted surfaces if the detergent is allowed to dry on the surface Wash and rinse a small section at a time Avoid working on hot surfaces or in direct sunlight e When you have finished using the detergent injection system remove the detergent suction tube from the detergent bottle and insert it
24. the trigger to release water pressure e Engage the safety lock on the trigger handle by pushing up on the safety lock until it clicks into the slot Fig 22 e Snap the desired nozzle onto the quick connect collar until it clicks into place and is secured properly Fig 23 Fig 23 Spray wand Nozzle Click rz Quick connect collar To disconnect a nozzle from the spray wand once the cleaning job is complete e Turn off the pressure washer and shut off the water supply Pull the trigger to release water pressure e Engage the safety lock on the trigger handle by pushing up on the safety lock until it clicks into the slot Fig 22 e Remove the nozzle by placing your hand over the nozzle while pulling back on the quick connect collar N WARNING Do not adjust the nozzle while the trigger is squeezed Failure to do so could result in damage Working with detergents When cleaning with the pressure washer some cleaning tasks can be solved with water alone but for most tasks cleaning with detergent allows for more effective dirt removal N WARNING Use only detergents designed for Pressure Washers DO NOT USE household detergents acids alkaline solutions bleaches solvents flammable material or industrial grade solutions These can damage the pump Many detergents may require mixing prior to use Prepare the cleaning solution as instructed on the solution bottle e Remove the cap from the detergen
25. way from the work area e Use the right product Do not use this machine for any job except that for which it is intended e Dress properly Do not wear loose clothing or jewelry They can get caught in moving parts Protective rubber gloves and non slip footwear are recommended when working outdoors e Caution Exercise caution to avoid slipping or falling Wear protective footwear that will protect your feet and improve your footing on slippery surfaces 2013 by Snow Joe LLC All rights reserved Original instructions hoary 7A aa 7A nal 7A OM slacitie Prasstira Wasna y 7 Form No SJ SPX3000 880E OPERATOR S MANUAL e Stay alert Watch what you are doing Use common sense Do not operate the pressure washer when you are tired or under the influence of alcohol or drugs Do not overreach Keep proper footing and balance at all times e Avoid unintentional starting Do not carry plugged in machine with finger on the trigger Make sure the switch is off before plugging in the machine Do not abuse the cord Never carry the machine by the cord or yank the cord to disconnect it from the receptacle Keep the cord away from heat oil and sharp edges Use safety glasses Also use safety footwear snug fitting clothing protective gloves hearing and head protection Water temperature Pressure washer is not meant to pump hot water NEVER connect it to a hot water supply as it will significantly reduc
Download Pdf Manuals
Related Search