Seagate MobileMax ST320LT030 hard disk drive
Contents
1. led eee Q 4 ES awed 13 CONFIGURING AND MOUNTING THE DRIVE 1 14 3 1 HANDLING AND STATIC DISCHARGE PRECAUTIONS 14 3 2 CONFIGURING THE DRIVE a hrs 14 3 2 1 Serial ATA Cables and Connectors 14 3 3 DRIVE MOUNTING ker pe TCR SURG Ra ed IUUD EY a RR PA ER RO 15 SERIAL ATA SATA Ih 16 4 1 HOT PLUG COMPATIBILITY Cuy ZO aq Mu s 16 4 2 SERIAL ATA DEVICE PLUG CONNECTOR PIN DEFINITIONS 16 4 3 SUPPORTED ATA COMMANDS lesse hrs 17 4 3 1 Identify Device 19 4 3 2 Set Features command 23 4 3 3 SMART commands ete EXHI a ee aay 24 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A FIGURE 1 TYPICAL 5V STARTUP AND OPERATION CURRENT PROFILE FIGURE 2 ATTACHING SATA CABLING FIGURE 3 MOUNTING DIMENSIONS FOR STANDARD MODELS SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A FIGURES Seagate Technology Support Services For information regarding online support and services visit http www seagate com about contact us technical support Available services include Presales amp Technical support Global Support Services telephone numbers amp b2. Word Description Value 51 PIO data transfer cycle timing mode 02004 52 Retired 0200 53 Words 54 58 64 70 and 88 are valid 00074 54 Number of current logical cylinders XXXXy 55 Number of current logical heads XXXXH 56 Number of current logical sectors per logical track XXXXH 57 58 Current capacity in sectors XXXXH 59 Number of sectors transferred during a XXXXH Read Multiple or Write Multiple command 60 61 Total number of user addressable sectors ST500LT032 OFFFFFFFh This field contains a value that is one greater than the total number of ST500LT033 OFFFFFFFh user addressable sectors The maximum value that shall be placed in this ST320LT030 OFFFFFFFh field is OFFFFFFFh The OFFFFFFFh value applies to all capacities over ST320LT031 OFFFFFFFh 137GB see Section 2 1 for related information 62 Retired 00004 63 Multiword DMA active and modes supported Xx07H see note following this table 64 Advanced PIO modes supported modes 3 and 4 supported 00034 65 Minimum multiword DMA transfer cycle time per word 120 ns 00784 66 Recommended multiword DMA transfer cycle time per word 120 ns 00784 67 Minimum PIO cycle time without IORDY flow control 240 ns 00784 68 Minimum PIO cycle time with IORDY flow control 120 ns 00784 69 74 ATA reserved 00004 75 Queue depth 001FH 76 Serial ATA capabilities 0D06H 77 ATA reserved 00004 78 Serial ATA features supported 00484 79 Serial ATA features enabled 00484 80 Major version numb
3. 201 500 Hz 1 0 Gs 0 to peak 2 8 2 2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below 5 500 Hz 5 0 Gs 0 to peak Max displacement may apply below 22 Hz SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 10 DRIVE SPECIFICATIONS 2 9 ACOUSTICS Drive emission of sound is measured consistent with the ECMA 74 and its referenced standards Testing is conducted at room temperature approximately 25 C Emission levels are reported as the total A weighted sound power levers for steady state idle and active seeks modes of operation IpLE PERFORMANCE SEEK 2 0 bels typ 2 2 bels typ 2 2 bels max 2 4 bels max 1 During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels 2 9 1 Test for prominent discrete tones PDTs Seagate follows the ECMA 74 standards for measurement and identification of PDTs An exception to this process is the use of the absolute threshold of hearing Seagate uses the lower limit for the threshold curve to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA 74 standards Defined as the median curve given by ISO 389 7
4. 2 4 PHYSICAL CHARACTERISTICS Height max 5 0 0 20 mm 0 197 0 008 in Width 69 85 0 25 mm 2 750 0 010 in All models Length 100 35 0 20 0 25 mm 3 951 40 008 0 010 in Typical weight 93g 0 20516 Cache buffer 16 MB 16 192 KB 2 5 SEEK TIME Seek measurements are taken with nominal power at 25 C ambient temperature All times are measured using drive diagnostics The specifications in the table below are defined as follows m Track to track seek time is an average of all possible single track seeks in both directions m Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks less overhead Table 1 Typical seek times Typical seek times ms Track to track Average Average latency Read 1 5 13 0 5 6 These drives are designed to consistently meet the seek times represented in this manual Physical seeks regardless of mode such as track to track and average are expected to meet the noted values However due to the manner in which these drives are formatted benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications 2 6 START STOP TIMES Table 2 Start stop times Typical seek times ms Power on to ready sec Power on to ready sec SED models Standby to ready sec Typical Max 25 C SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANU
5. 304 8m to 3048m 304 8m to 12 192m Altitude 1000ft to 10 000ft 1000ft to 40 000ft The recommended storage period year under controlled conditions of 34 C 90 RH or less 90 days in uncontrolled storage conditions 2 8 1 Shock 2 8 1 1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 400 Gs based on half sine shock pulses of 2ms Shocks should not be repeated more than one time per axis 2 8 1 2 Nonoperating shock The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half sine shock pulse of 2 ms duration The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 1000 Gs based on a nonrepetitive half sine shock pulse of 1 ms duration 2 8 2 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws Vibration may be applied in the X Y or Z axis 2 8 2 1 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below 5 200 Hz 2 0 Gs 0 to peak Max displacement may apply below 10 Hz
6. 5V power Ground 2nd mate Ground or LED signal If grounded drive does not use deferred spin Ground ist mate 12V power pre charge 2nd mate 12V power P15 V42 12V power SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 16 NOTES 1 All pins are in a single row with a 1 27 mm 0 050 in pitch 2 The comments on the mating sequence apply to the case of backplane blindmate connector only In this case the mating sequences are the ground pins P4 and P12 the pre charge power pins and the other ground pins the signal pins and the rest of the power pins 3 There are three power pins for each voltage One pin from each voltage is used for pre charge when installed in a blind mate backplane configuration 4 All used voltage pins V must be terminated 4 3 SUPPORTED ATA COMMANDS Table 6 lists Serial ATA standard commands that the drive supports For a detailed description of the ATA commands refer to the Serial ATA International Organization Serial ATA Revision 2 6 Refer to www sata io org Refer to S M A R T commands on page 24 for details and subcommands used in the S M A R T implementation Table 6 Supported ATA commands ATA standard commands names Command code in hex Device Configuration Restore B1h COh Device Configuration Freeze Lock B1h C1h Device Configuration Identify B1h C2h Device Configur
7. Seagate Product Manual Seagate Laptop Ultrathin HDD SATA Standard models Self Encrypting Drive models ST500LT032 ST500LT033 ST320LT030 ST320LT031 Gen 9 3 100715053 Rev A May 2013 Document Revision History Revision Date Description of Change Rev A 05 07 2013 Initial release 2013 Seagate Technology LLC All rights reserved Publication number 100715053 Rev A May 2013 Seagate Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and or other countries Seagate Laptop Ultrathin HDD and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and or other countries The FIPS logo is a certification mark of NIST which does not imply product endorsement by NIST the U S or Canadian governments All other trademarks or registered trademarks are the property of their respective owners No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC Call 877 PUB TEK1 877 782 8351 to request permission When referring to drive capacity one gigabyte or GB equals one billion bytes and one terabyte or TB equals one trillion bytes Your computer s operating system may use a different standard of measurement and report a lower capacity In addition some of the listed capacity is used for formatting and other functions
8. 3 505 075 3x90 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 15 SERIAL ATA SATA INTERFACE 4 0 SERIAL ATA SATA INTERFACE These drives use the industry standard Serial ATA interface that supports FIS data transfers It supports ATA programmed input output PIO modes 0 4 multiword DMA modes 0 2 and Ultra DMA modes 0 6 The drive also supports the use of the IORDY signal to provide reliable high speed data transfers For detailed information about the Serial ATA interface refer to the Serial ATA High Speed Serialized AT Attachment specification 4 1 HoT PLUG COMPATIBILITY Seagate Laptop Ultrathin HDD SATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA High Speed Serialized AT Attachment specification revision 2 0 This specification can be downloaded from www serialata org This device requires a COMRESET from the host after a hotplug event 4 2 SERIAL ATA DEVICE PLUG CONNECTOR PIN DEFINITIONS Table 5 summarizes the signals on the Serial ATA interface and power connectors Refer to the Notes below Table 5 Serial ATA Connector Pin Definitions Segment Pin Function Definition 2nd mate Differential signal pair A from Phy 2nd mate Differential signal pair B from Phy 2nd mate 3 3V power 3 3V power 3 3V power pre charge 2nd mate Ground 1st mate 2nd mate 2nd mate 5V power pre charge 2nd mate 5V power
9. Tf curve minus 10dB at all frequencies 2 10 ELECTROMAGNETIC IMMUNITY When properly installed in a representative host system the drive operates without errors or degradation in performance when subjected to the radio frequency RF environment as defined in Table 4 Table 4 Radio Frequency Environments PERFORMANCE REFERENCE LEVEL STANDARD Electrostatic discharge Contact HCP VCP 4 kV Air 8 kV B EN 61000 4 2 95 80 to 1 000 MHz 3 V m Radiated RF immunity 80 AM with 1 kHz sine A TEST DESCRIPTION EN 61000 4 3 96 ENV 50204 95 900 MHz 3 V m 50 pulse modulation 200 Hz Electrical fast transient 1kV on AC mains 0 5 kV on external I O B EN 61000 4 4 95 1 kV differential 2 kV common AC mains B EN 61000 4 5 95 Conducted RF immunity 150 kHz to 80 MHz 3 Vrms 80 AM with 1 kHz sine A EN 61000 4 6 97 Power Frequency H field A m 50Hz 60Hz 3 axes A EN 61000 4 8 97 immunity 3096 Reduction for 25 cycles Voltage dips interrupts gt 95 Reduction for 250 cycles 29596 0 5 cycles EN 61000 4 11 94 goa SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 11 DRIVE SPECIFICATIONS 2 11 RELIABILITY Nonrecoverable read errors per 1014 bits read max Load Unload U UL 25 C 5096 relative humidity 600 000 software controlled power on off cycles 20 000 hard power on off cycles Warranty To determine the warranty for a specific drive use a web browser to access the f
10. 0 Ultra DMA mode 2 is currently active 1 Ultra DMA mode 3 is currently active 2 Ultra DMA mode 4 is currently active 13 Ultra DMA mode 5 is currently active 14 Ultra DMA mode 6 is currently active Bit Word 93 13 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 1 80 conductor cable detected CBLID above VIH 0 40 conductor cable detected CBLID below VIL SERIAL ATA SATA INTERFACE 22 SERIAL ATA SATA INTERFACE 4 3 2 Set Features command This command controls the implementation of various features that the drive supports When the drive receives this command it sets BSY checks the contents of the Features register clears BSY and generates an interrupt If the value in the register does not represent a feature that the drive supports the command is aborted Power on default has the read look ahead and write caching features enabled The acceptable values for the Features register are defined as follows Table 8 Set Features command values 02g Enable write cache default 03g Set transfer mode based on value in Sector Count register Sector Count register values 004 Set PIO mode to default PIO mode 2 Oly Set PIO mode to default and disable IORDY PIO mode 2 08 PIO mode 0 09g PIO mode 1 OAy PIO mode 2 OBy PIO mode 3 OCy PIO mode 4 default 20g Multiword DMA mode 0 214 Multiword DMA mode 1 22g Multiword DMA mode 2 40g Ultra DMA mode 0 41g Ultra DMA mode 1 42g
11. 6 2 7 POWER SPECIFICATIONS llle sees 7 2 7 1 Power CONSUMPTION se ne sterke opke ER awe a une E eke RE 7 2 7 2 GOnGUCIEd NOISE et re er e OX SR SURE RB Fe RTI SL C ER DEO e Ra 9 2 7 3 Voltage tolerance scsi pred Lae aed thongs Sebo Cha DERE DLE 9 2 7 4 Power management 9 2 8 ENVIRONMENTAL SPECIFICATIONS u lu ua has 10 2 8 1 SOC na mua wat LEM RE eee p bera e NR Ced da 10 2 8 2 Vibrations ee ea ertet bere anh ur oven T Cai OL iR NATI QA 10 2 9 ACOUSTICS S C S Rau yu Cane aun E Gea dead 11 2 9 1 Test for prominent discrete tones PDTS 11 2 10 ELECTROMAGNETIC IMMUNITY 11 2 11 RELIABILITY sce 22 2 ice Dex as ate QUA Meteora ee ed uiid 12 2 12 AGENCY 12 2 12 1 12 2 12 2 Electromagnetic Compatibility 12 2 12 38 FOO veriflCallOn az s sete rptu beu T PER IER risiede 12 2 13 ENVIRONMENTAL PROTECTION lees 13 2 13 1 European Union Restriction of Hazardous Substances RoHS Directive 13 2 13 2 China Restriction of Hazardous Substances RoHS Directive 13 2 14 CORROSIVE ENVIRONMENT bei eda
12. Host Interface FEh S M A R T Read Attribute Thresholds BOh D1h S M A R T Read Data BOh DOh S M A R T Read Log Sector BOh D5h S M A R T Return Status BOh DAh S M A R T Save Attribute Values BOh D3h S M A R T Write Attribute Thresholds BOh D7h S M A R T Write Attribute Values BOh E1h S M A R T Write Log Sector BOh D6h Write Buffer E8h Write DMA CAh Write DMA Extended 35h Write DMA without Retries CBh Write Long with Retries 32h Write Long without Retries 33h Write Multiple C5h Write Multiple Extended 39h Write Sectors 30h 31h Write Sectors Extended 34h ATA standard power management commands Check Power Mode E5h Idle E3h Idle Immediate Eth Sleep E6h Standby E2h SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 18 Table 6 Supported ATA commands SERIAL ATA SATA INTERFACE ATA standard commands names Command code in hex Standby Immediate EOh ATA standard security commands Security Set Password Fih Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h 4 3 1 Identify Device command The Identify Device command command code EC transfers information about the drive to the host following power up The data is organized as a single 512 byte block of data whose contents are shown in Table 7 All reserved bits or words should be set to zero Parameters listed with an x are
13. Revision 2 6 specification 1 One GB equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting 2 1 FORMATTED CAPACITY MODEL FORMATTED Capacity GUARANTEED SECTORS BYTES PER SECTOR 500GB model 500 GB 976 773 168 512 logical 4096 physical 320GB model 625 142 448 1 One GB equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting 2 1 1 LBA mode When addressing these drives in LBA mode all blocks sectors are consecutively numbered from 0 to n 7 where n is the number of guaranteed sectors as defined above Refer to Configuring and Mounting the Drive on page 14 words 60 61 and 100 103 for additional information about 48 bit addressing support of drives with capacities over 137 GB 2 2 PHYSICAL ORGANIZATION Drive model Read write heads Number of discs ST500LT032 and ST500LT033 ST320LT030 and ST320LT031 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 5 DRIVE SPECIFICATIONS 2 3 RECORDING AND INTERFACE TECHNOLOGY Interface Serial ATA SATA Recording method Perpendicular 1885 Kb in Recording density Track density 366 ktracks in avg Areal density 690 Gb in avg Spindle speed 5400 RPM 0 2 Sustained data transfer rate 100 MB s max I O data transfer rate 600 MB s max
14. Spindle speed 5400 RPM Sustained data transfer rate OD 100 MB s max I O data transfer rate 600 MB s max PIO modes 0 4 ATA data transfer modes supported Multiword DMA modes 0 2 Ultra DMA modes 0 6 MUERE 596 to 9596 operating Relat ye nanny 5 to 95 nonoperating Relative humidity gradient 30 per hour max 37 7 C max operating 40 0 C max nonoperating 304 8 m to 3048 m 1000 ft to 10 000 ft Wet bulb temperature max Altitude operating Altitude nonoperating 304 8 m to 12 192 m 1000 ft to 40 000 ft below mean sea level max 400 Gs at 2 ms max 1000 Gs at 1 ms max Operational Shock Non Operational Shock SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 4 DRIVE SPECIFICATIONS ST500LT032 ST320LTO30 5 200 Hz 2 0 Gs Vibration operating 201 500 Hz 1 0 Gs Vibration nonoperating 5 500 Hz 5 0 Gs Nonrecoverable read errors 1 per 1014 bits read To determine the warranty for a specific drive use a web browser to access the following web page http www seagate com support warranty and replacements Warranty From this page click on the Verify Your Warranty link You will be asked to provide the drive serial number model number or part number and country of purchase The system will display the warranty information for your drive Load unload cycles 600 000 at 25 C 50 rel humidity Supports Hotplug operation per the Yes Serial ATA
15. and thus will not be available for data storage Actual quantities will vary based on various factors including file size file format features and application software Actual data rates may vary depending on operating environment and other factors The export or re export of hardware or software containing encryption may be regulated by the U S Department of Commerce Bureau of Industry and Security for more information visit www bis doc gov and controlled for import and use outside of the U S Seagate reserves the right to change without notice product offerings or specifications 1 0 2 0 3 0 4 0 CONTENTS SEAGATE TECHNOLOGY SUPPORT SERVICES 1 INTRODUCTION 25 lxi iia Ss deed A i Hem EV ee eed E ARE ER 2 1 1 ABOUT THE SERIAL ATA INTERFACE 3 DRIVE SPECIFICATIONS luem p Mee Ga Re oe A E Reden de bere a cn 4 2 1 FORMATTED CAPACITY sh exi eid tar hoodia wealth nee S eon e een 5 2 1 1 BA MOOG Di acr vencedor ert 5 2 2 PHYSICAL ORGANIZATION ua MR QUE E ua DEA PA a QE Und 5 2 3 RECORDING AND INTERFACE TECHNOLOGY 6 24 PHYSICAL CHARACTERISTICS Erde ed seo Re ER AN RI UA a taal edb PRA 6 2 5 SEEK TIMES aa pa ced rut nis REESE RR E nee eem EO REIR NOCH Ee BORNE LS 6 2 6 START STOP TIMES sc s d wu exei a e her S dana TRE sta Sasu RT RAO es
16. drive motherboard power supply etc does comply with the limits for a Class B computing device pursuant to Subpart J Part 15 of the FCC rules Operation with noncertified assemblies is likely to result in interference to radio and television reception Radio and television interference This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer s instructions may cause interference to radio and television reception This equipment is designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television which can be determined by turning the equipment on and off you are encouraged to try one or more of the following corrective measures SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 12 DRIVE SPECIFICATIONS Reorient the receiving antenna Move the device to one side or the other of the radio or TV Move the device farther away from the radio or TV Plug the computer into a different outlet so that the receiver and computer are on different branch outlets If necessary you should consult your dealer or an experienced radio television technician for additional suggestions You may find helpful the following booklet prepared by the Federal Communications Commission How to Iden
17. errors 12 O operating shock 10 operating vibration 10 P physical characteristics 6 Physical organization 5 point to point 3 14 power consumption 7 power dissipation 7 power management modes 9 power modes 9 power specifications 7 precautions 14 printed circuit board 14 programmable power management 9 prominent discrete tone 11 Q quick reference 4 R Radiated RF immunity 11 radio and television interference 12 radio frequency RF 11 random track location 7 Read Buffer 17 Read DMA 17 Read DMA Extended 17 Read DMA without Retries 17 readerrors 12 Read Long with Retries 17 Read Long without Retries 17 Read Multiple 17 Read Multiple Extended 17 Read Native Max Address 17 Read Native Max Address Extended 17 Read Sectors 17 Read Sectors Extended 17 Read Sectors without Retries 17 Read Verify Sectors 17 Read Verify Sectors Extended 17 Read Verify Sectors without Retries 17 read write power 7 recording density 6 recording method 6 recording technology 6 INDEX reliability 12 Retries 17 RMS read write current 9 RoHS 13 RRL 12 S S M A R T 18 S M A R T implementation 17 safety certification 12 SATA ports 3 screws 15 Seagate Technology Support Services 1 sectors 5 Security Disable Password 19 Security Erase Prepare 19 Security Erase Unit 19 Security Freeze Lock 19 Security Set Password 19 Security Unlock 19 Seek 17 seek mode 7 Seek time 6 seektime 7 Self refresh
18. low power 9 Serial ATA SATA interface 16 Set Features 18 Set Max Address 18 Set Multiple Mode 18 shock 10 single track seeks 6 Sleep 18 sleep 7 sleep mode 9 spindle speed 6 spinup DC power 7 spinup power 7 Standby 18 standby 7 Standby Immediate 19 standby mode 7 9 standby timer 9 Start stop times 7 static discharge 14 subassembly 12 surge immunity 11 T temperature 6 timers Idle and Standby 9 track density 6 Track to track seek time 6 Transport major version number 21 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 26 U UL60950 1 12 V vibration 10 voltage dips interrupts 11 voltage tolerance 9 W warranty 12 weight 6 width 6 Write Buffer 18 Write DMA 18 Write DMA Extended 18 Write Long with Retries 18 Write Long without Retries 18 Write Multiple 18 Write Sectors 18 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A INDEX 27 e Seagate Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard Cupertino California 95014 United States 408 658 1000 ASIA PACIFIC Seagate Singapore International Headquarters Pte Ltd 7000 Ang Mo Kio Avenue 5 Singapore 569877 65 6485 3888 EUROPE MIDDLE EAST AND AFRICA Seagate Technology SAS 16 18 rue du D me 92100 Boulogne Billancourt France 33 1 4186 10 00 Publication Number 100715053 Rev A May 2013
19. AL REV A 6 DRIVE SPECIFICATIONS 2 7 POWER SPECIFICATIONS The drive receives DC power 5V through a native SATA power connector refer to Figure 2 2 7 1 Power consumption Power requirements for the drives are listed in the table in Table 3 Typical power measurements are based on an average of drives tested under nominal conditions at 25 C ambient temperature These power measurements are done with Interface Power Management modes like HIPM and DIPM enabled Spinup power Spinup power is measured from the time of power on to the time that the drive spindle reaches operating speed Seek mode During seek mode the read write actuator arm moves toward a specific position on the disk surface and does not execute a read or write operation Servo electronics are active Seek mode power is measured based on three random seek operations every 100 ms This mode is not typical Read write power and current Read write power is measured with the heads on track based on three 63 sector read or write operations every 100 ms Idle mode power Idle mode power is measured with the drive up to speed with servo electronics active and with the heads in a random track location Standby mode During standby mode the drive accepts commands but the drive is not spinning and the servo and read write electronics are in power down mode Table 3 Power dissipation 1 2 POWER DISSIPATION 5V INPUT AVERAGE 25 C Spi
20. Gb s Perpendicular recording technology State of the art cache and on the fly error correction algorithms Native Command Queuing NCQ with command ordering Full track multiple sector transfer capability without local processor intervention 1000 Gs nonoperating shock and 400 Gs of operating shock SeaTools diagnostic software performs a drive self test that eliminates unnecessary drive returns The 3D Defense System which includes Drive Defense Data Defense and Diagnostic Defense offers the industry s most comprehensive protection for disk drives Support for S M A R T drive monitoring and reporting Support for Read Multiple and Write Multiple commands Worldwide Name WWN capability uniquely identifies the drive Momentus Thin Self Encrypting Drive models have the following additional features Automatic data encryption decryption Controlled access Random number generator Drive locking 16 independent data bands Cryptographic erase of user data for a drive that will be repurposed or scrapped Authenticated firmware download There is no significant performance difference between Self Encrypting Drive and standard non Self Encrypting Drive models SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 1 1 ABOUT THE SERIAL ATA INTERFACE The Serial ATA interface provides several advantages over the traditional parallel ATA interface The primary advantages include m Easy installation and configuration w
21. Ultra DMA mode 2 43g Ultra DMA mode 3 44g Ultra DMA mode 4 45g Ultra DMA mode 5 46 Ultra DMA mode 6 55g Disable read look ahead read cache feature 82g Disable write cache AAy Enable read look ahead read cache feature default Cly Disable the Free Fall Protection feature 414 above enables the Free Fall Protection feature Fly Report full capacity available At power on or after a hardware or software reset the default values of the features are as indicated above SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 23 SERIAL ATA SATA INTERFACE 4 3 3 S M A R T commands S M A R T provides near term failure prediction for disk drives When S M A R T is enabled the drive monitors predetermined drive attributes that are susceptible to degradation over time If self monitoring determines that a failure is likely S M A R T makes a status report available to the host Not all failures are predictable S M A R T predictability is limited to the attributes the drive can monitor For more information on S M A R T commands and implementation see the Draft ATA 5 Standard SeaTools diagnostic software activates a built in drive self test DST S M A R T command for D44 that eliminates unnecessary drive returns The diagnostic software ships with all new drives and is also available at http www seagate com support downloads seatools This drive is shipped with S M A R T features disabled Y
22. ation Set B1h C3h Download Microcode 92h Execute Device Diagnostics 90h Flush Cache E7h Flush Cache Extended EAh Identify Device ECh Initialize Device Parameters 91h Read Buffer E4h Read DMA C8h Read DMA Extended 25h Read DMA without Retries C9h Read Long with Retries 22h Read Long without Retries 23h Read Multiple C4h Read Multiple Extended 29h Read Native Max Address F8h Read Native Max Address Extended 27h Read Sectors 20h Read Sectors Extended 24h Read Sectors without Retries 21h Read Verify Sectors 40h Read Verify Sectors Extended 42h Read Verify Sectors without Retries 41h Seek 70h SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 17 SERIAL ATA SATA INTERFACE Table 6 Supported ATA commands ATA standard commands names Command code in hex Set Features EFh Set Max Address F9h Note Individual Set Max commands are identified by the Address 004 value placed in the Set Max Features register as defined to Password 01g the right Lock 024 Unlock 03 Freeze Lock 044 Set Max Address Ext 37h Set Multiple Mode C6h S M A R T Disable Operations BOh D9h S M A R T Enable Disable Autosave BOh D2h S M A R T Enable Operations BOh D8h S M A R T Enable Disable Auto Offline BOh DBh S M A R T Enable One Attribute Modification BOh EOh S M A R T Execute Offline BOh D4h S M A R T Free Fall Protection
23. drive specific or vary with the state of the drive Refer to Drive Specifications on page 4 for default parameter settings The following commands contain drive specific features that may not be included in the Serial ATA specification Table 7 Identify Device command Word Description Value Configuration information OC5Ay Bit 15 0 ATA 1 ATAPI 0 Bit 7 removable media Bit 6 removable controller Bit 0 reserved 1 Number of logical cylinders 16 383 2 Specific configuration C837H 3 Number of logical heads 16 4 Retired 0000 5 Retired 0000 6 Number of logical sectors per logical track 63 003FH 7 9 Retired 0000 10 19 Serial number 20 ASCII characters 00004 none ASCII 20 Retired 0000 21 Retired 8000 22 Obsolete 00044 23 26 Firmware revision X XX 8 ASCII character string padded with blanks to end of string 27 46 Drive model number ST500LT032 40 ASCII characters padded with blanks to end of string ST500LT033 ST320LT030 ST320LT031 47 Bits 7 0 80104 Maximum sectors per interrupt on Read multiple and Write multiple 16 48 Trusted Computing Feature set options 00004 49 Standard Standby timer IORDY supported and may be disabled 2F004 50 Capabilities 40004 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 19 Table 7 Identify Device command SERIAL ATA SATA INTERFACE
24. e NOTE Each drive will have a unique value This field is valid if word 84 bit 8 is set to 1 indicating 64 bit WWN support 112 118 ATA reserved 00004 119 Free Fall Protection support bit 5 1 Free Fall Protection supported 0 Free Fall Protection not supported 120 Free Fall Protection enable disable bit 5 1 Free Fall Protection feature is enabled 0 Free Fall Protection feature is disabled 121 127 ATA reserved 0000 128 Security status 00214 129 159 Seagate reserved XXXXH 160 221 ATA reserved 00004 222 Transport major version number 101FH 223 254 ATA reserved 00004 255 Integrity word xXA5H NOE See the bit descriptions below for words 63 88 and 93 of the Identify Drive data Description if bit is set to 1 Bit Word 63 0 Multiword DMA mode 0 is supported 1 Multiword DMA mode 1 is supported 2 Multiword DMA mode 2 is supported 8 Multiword DMA mode 0 is currently active 9 Multiword DMA mode 1 is currently active 10 Multiword DMA mode 2 is currently active SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 21 Word 88 Ultra DMA mode 0 is supported Ultra DMA mode 1 is supported Ultra DMA mode 2 is supported Ultra DMA mode 3 is supported Ultra DMA mode 4 is supported Ultra DMA mode 5 is supported Ultra DMA mode 6 is supported Ultra DMA mode 0 is currently active 1 1 1 Ultra DMA mode 1 is currently active
25. e drive leaves sleep mode after it receives a hard reset or soft reset from the host After receiving a reset the drive exits sleep mode and enters standby mode with all current translation parameters intact Idle and standby timers Each time the drive performs an active function read write or seek the standby timer is reinitialized and begins counting down from its specified delay times to zero If the standby timer reaches zero before any drive activity is required the drive makes a transition to standby mode In both Idle and standby mode the drive accepts all commands and returns to active mode when disk access is necessary SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 9 DRIVE SPECIFICATIONS 2 8 ENVIRONMENTAL SPECIFICATIONS This section provides the temperature humidity shock and vibration specifications for Momentus drives Ambient temperature is defined as the temperature of the environment immediately surrounding the drive Above 1000 feet 305 meters the maximum temperature is derated linearly by 1 C every 1000 feet Parameters Operating Non Operating Ambient temperature 0 to 60 C 32 to 140 F 40 to 70 C 40 to 158 F 20 C per hour 68 F per hour max 35 C per hour 95 F per hour max Temperature gradient without condensation without condensation Humidit 5 to 95 non condensing 5 to 95 non condensing y 3096 per hour 30 per hour Wet bulb 37 7 C 99 8 F max 40 C 104 F max
26. er 01F04 81 Minor version number 00294 82 Command sets supported 746BH 83 Command sets supported 7D69y 84 Command sets support extension 61E3y 85 Command sets enabled 7469 86 Command sets enabled 49 87 Command sets enable extension 61E3y 88 Ultra DMA support and current mode see note following this table XX7Fy 89 Security erase time XXXXH 90 Enhanced security erase time XXXXH 91 Current APM values 80804 92 Master password revision code FFFEH SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 20 SERIAL ATA SATA INTERFACE Table 7 Identify Device command Word Description Value 93 Hardware reset value see description following this table XXXXy 94 Auto acoustic management setting XXXXy 95 Stream Min Request Size 0000 96 Streaming Transfer Time DMA 00004 97 Streaming Access Latency DMA and PIO 00004 98 99 Streaming Performance Granularity 0000 100 103 Total number of user addressable LBA sectors available ST500LT032 976 773 168 see Section 3 2 for related information ST500LT033 976 773 168 These words are required for drives that support the 48 bit addressing ST320LT030 625 142 448 feature Maximum value OOOOFFFFFFFFFFFFh ST320LT031 625 142 448 104 Streaming Transfer Time PIO 00004 105 Reserved 00004 106 Physical sector size Logical sector size 60034 107 Seagate reserved 00004 108 111 The mandatory value of the world wide name WWN for the driv
27. ith true plug and play connectivity It is not necessary to set any jumpers or other configuration options m Thinner and more flexible cabling for improved enclosure airflow and ease of installation m Scalability to higher performance levels In addition Serial ATA makes the transition from parallel ATA easy by providing legacy software support Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current system and expect all of your existing applications to work as normal The Serial ATA interface connects each disk drive in a point to point configuration with the Serial ATA host adapter There is no master slave relationship with Serial ATA devices like there is with parallel ATA If two drives are attached on one Serial ATA host adapter the host operating system views the two devices as if they were both masters on two separate ports This essentially means both drives behave as if they are Device 0 master devices The host adapter may optionally emulate a master slave environment to host software where two devices on separate Serial ATA ports are represented to host software as a Device 0 master and Device 1 slave accessed at the same set of host bus addresses A host adapter that emulates a master slave environment manages two sets of shadow registers This is not a typical Serial ATA environment The Serial ATA host adapter and drive share the function of emulating paralle
28. l ATA device behavior to provide backward compatibility with existing host systems and software The Command and Control Block registers PIO and DMA data transfers resets and interrupts are all emulated The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers referred to as the Shadow Register Block All Serial ATA devices behave like Device 0 devices For additional information about how Serial ATA emulates parallel ATA refer to the Serial ATA International Organization Serial ATA Revision 3 0 The specification can be downloaded from www serialata org SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 3 DRIVE SPECIFICATIONS 2 0 DRIVE SPECIFICATIONS Unless otherwise noted all specifications are measured under ambient conditions at 25 C and nominal power For convenience the phrases the drive and this drive are used throughout this manual to indicate the following drive models The specification summaries listed in the following tables are for quick reference For details on specification measurement or definition refer to the appropriate section of this manual one m Formatted capacity 500 GB 320 GB Guaranteed sectors 976 773 168 625 142 448 Heads 2 Disks 1 Bytes per sector 512 logical 4096 physical Recording density 1885 Kb in Track density 366 Ktracks in avg Areal density 690 Gb in avg
29. ltrathin HDD SATA drives support latching SATA connectors SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 14 3 3 DRIVE MOUNTING You can mount the drive in any orientation using four screws in the side mounting holes or four screws in the bottom mounting holes Refer to Figure 3 for drive mounting dimensions Follow these important mounting precautions when mounting the drive Allow a minimum clearance of 0 030 in 0 76 mm around the entire perimeter of the drive for cooling Use only M3 x 0 5 mounting screws Do not overtighten the mounting screws Maximum torque 4 0 in Ib 0 4519 N m Three 3 threads 0 080 in 2 032 mm minimum screw engagement recommended Avoid excessive drive distortion when mounting Refer to the following specifications for stiffness deflection information Top cover stiffness deflection Operating no performance degradation emitted noise 10 mm probe 1 02kgf or mechanical damage or hard errors 5 mm probe 0 92kgf Non operating no hard errors 20 mm probe 2 0kgf at any point of top cover 20 mm probe 15 0kgf at top cover edges only Figure 3 Mounting Dimensions for standard models E 100 350 0 200 69 850 0 250 2 13 430 1 Y T 8 230 121209 2 3 500 1 90 600 u 2 m 5 000 0 200 1 2x 2 997 N BOTH SIDES 2X M3x0 5 6H MOUNTING HOLES BOTH SIDES MIN 3 FULL THREADS Z
30. nt to provide greater energy efficiency In most systems power management is controlled through the system setup program The drive features the following power management modes POWER MODES HEADS SPINDLE BUFFER Active operating Tracking Rotating Full power Idle performance Tracking Rotating Self refresh low power Idle active Floating Rotating Self refresh low power Idle low power Parked Rotating Self refresh low power Standby Parked Stopped Self refresh low power Sleep Parked Stopped Self refresh low power Active mode The drive is in active mode during the read write and seek operations Idle mode The buffer remains enabled and the drive accepts all commands and returns to active mode any time disk access is necessary Standby mode The drive enters standby mode when the host sends a standby Immediate command If the host has set the standby timer the drive can also enter standby mode automatically after the drive has been inactive for a specifiable length of time The standby timer delay is established using a standby or idle command In standby mode the drive buffer is enabled the heads are parked and the spindle is at rest The drive accepts all commands and returns to active mode any time disk access is necessary Sleep mode The drive enters sleep mode after receiving a sleep command from the host In sleep mode the drive buffer is disabled the heads are parked and the spindle is at rest Th
31. nup max 1 00A Seek average 1 4W Write average 1 70W Read average 1 30W Idle performance D 1 10 Idle active 0 66W Idle low power mode 0 47W Standby 0 18W Sleep 0 18W During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels Standby power is measured at steady state after 200ms from transition SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 7 2 7 1 1 Typical current profiles The typical 5V startup and operation current profile is shown in Figure 1 Figure 1 Typical 5V Startup and Operation Current Profile 21 Jan 13 3 47 40 Motor Spinup to Ready DC 8 448 V bey ISD SEE SES e SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A u DRIVE SPECIFICATIONS 5V Input Supply Current 188 kS s STOPPED DRIVE SPECIFICATIONS 2 7 2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15 ohm resistive load on the 5 volt line m Using 5 volt power the drive is expected to operate with a maximum of 100 mV peak to peak square wave injected noise at up to 10 MHz Nor Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read write current 273 Voltage tolerance Voltage tolerance including noise m 5V 5 2 7 4 Power management modes The drive provides programmable power manageme
32. ollowing web page http www seagate com support warranty and replacements From this page click on the Verify Your Warranty link You will be asked to pro vide the drive serial number model number or part number and country of pur chase The system will display the warranty information for your drive 2 12 AGENCY CERTIFICATION 2 12 1 Safety certification These products are certified to meet the requirements of UL60950 1 CSA60950 1 and EN60950 and so marked as to the certify agency 2 12 2 Electromagnetic Compatibility EMC Hard drives that display the CE mark comply with the European Union EU requirements specified in the Electromagnetic Compatibility Directive 2004 108 EC as put into place 20 July 2007 Testing is performed to the levels specified by the product standards for Information Technology Equipment ITE Emission levels are defined by EN 55022 Class B and the immunity levels are defined by EN 55024 Drives are tested in representative end user systems Although CE marked Seagate drives comply with the directives when used in the test systems we cannot guarantee that all systems will comply with the directives The drive is designed for operation inside a properly designed enclosure with properly shielded I O cable if necessary and terminators on all unused I O ports Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products Korean RRL If these d
33. ou must have a recent BIOS or software package that supports S M A R T to enable this feature The table below shows the S M A R T command codes that the drive uses Table 9 S M A R T Commands CODE IN FEATURES REGISTER S M A R T COMMAND S M A R T Read Data D24 S M A R T Enable Disable Attribute Autosave D34 S M A R T Save Attribute Values D44 S M A R T Execute Off line Immediate runs DST D5g S M A R T Read Log Sector D6g S M A R T Write Log Sector D8g S M A R T Enable Operations D9y S M A R T Disable Operations DAg S M A R T Return Status If an appropriate code is not written to the Features Register the command is aborted and 0x04 abort is written to the Error register SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 24 A acoustics 11 active mode 9 Address 18 agency certification 12 ambient temperature 6 areal density 6 ATAcommands 17 Australia New Zealand Standard AS NZS3548 1995 12 Australian Communication Authority ACA 12 Australian C Tick 12 Average seek time 6 B buffer 6 C cables and connectors 14 capacity 5 CEmark 12 certification 12 Check Power Mode 18 China RoHS directive 13 compatibility 12 conducted noise 9 conducted RF immunity 11 configuring and mounting the drive 14 connectors 14 corrosive environment 13 CSA60950 1 12 D DC power 7 density 6 Device Configuration Freeze Lock 17 Device Configuration Resto
34. re 17 Device Configuration Set 17 Diagnostics 17 dimensions 15 dissipation 7 Download Microcode 17 E electrical fast transient 11 Electromagnetic Compatibility EMC 12 Electromagnetic Compatibility control Regulation 12 Electromagnetic Compatibility Directive 2004 108 EC 12 electromagnetic immunity 11 electrostatic discharge ESD 11 14 EN 55022 Class 12 EN 55024 12 EN60950 12 enclosures 12 environmental specifications 10 INDEX errors 12 ESD 14 EU 12 EU RoHS directive 13 European Union EU requirements 12 evice Configuration Identify 17 Execute Device Diagnostics 17 F FCC verification 12 features 2 Flush Cache 17 Flush Cache Extended 17 formatted capacity 5 Freeze Lock 17 G Gs acceleration of gravity 10 guaranteed sectors 5 H handling precautions 14 height 6 I O data transfer rate 6 Identify 17 Identify Device 17 Identify Device command 19 Idle 18 Idle Immediate 18 idle mode 7 9 idle performance 7 Information Technology Equipment ITE 12 Initialize Device Parameters 17 input noise ripple 9 interface 16 interference 12 ITE 12 K KCC 12 Korean Communications Commission 12 Korean Radio Research Laboratory RRL 12 L LBA mode 5 length 6 master slave 3 Max Address 18 Microcode 17 mounting 15 SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 25 N noise 9 nominal power 6 nonoperating shock 10 nonoperating vibration 10 nonrecoverable read
35. rives have the Korean Communications Commission KCC logo they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility EMC Framework requirements of the Radio Research Laboratory RRL Communications Commission Republic of Korea These drives have been tested and comply with the Electromagnetic Interference Electromagnetic Susceptibility EMI EMS for Class B products Drives are tested in a representative end user system by a Korean recognized lab m Certificate number KCC REM STX Ultrathin m Trade name or applicant Seagate Technology LLC m Certificate date 2013 04 19 m Manufacturer nationality USA Singapore and China Australian C Tick N176 If these models have the C Tick marking they comply with the Australia New Zealand Standard AS NZS3548 1995 and meet the Electromagnetic Compatibility EMC Framework requirements of the Australian Communication Authority ACA 2 12 3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure not attached as an external device As such each drive is considered to be a subassembly even when it is individually marketed to the customer As a subassembly no Federal Communications Commission verification or certification of the device is required Seagate has tested this device in enclosures as described above to ensure that the total assembly enclosure disk
36. rranty Some factory installed labels contain information needed to service the drive Other labels are used to seal out dirt and contamination CAUTION 3 2 CONFIGURING THE DRIVE Each drive on the Serial ATA interface connects in a point to point configuration with the Serial ATA host adapter There is no master slave relationship because each drive is considered a master in a point to point relationships If two drives are attached on one Serial ATA host adapter the host operating system views the two devices as if they were both masters on two separate ports Both drives behave as if they are Device 0 master devices 3 2 1 Serial ATA Cables and Connectors The Serial ATA interface cable consists of four conductors in two differential pairs plus three ground connections The cable size may be 30 to 26 AWG with a maximum length of one meter 39 37 in Refer to Table 5 for connector pin definitions Either end of the SATA signal cable can be attached to the drive or host For direct backplane connection the drive connectors are inserted directly into the host receptacle The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable For installations which require cables you can connect the drive as shown in Figure 2 Figure 2 Attaching SATA Cabling inal nnetr er nnetr inal ale er ale Each cable is keyed to ensure correct orientation Seagate Laptop U
37. tify and Resolve Radio Television Interference Problems This booklet is available from the Superintendent of Documents U S Government Printing Office Washington DC 20402 Refer to publication number 004 000 00345 4 2 13 ENVIRONMENTAL PROTECTION Seagate designs its products to meet environmental protection requirements worldwide including regulations restricting certain chemical substances 2 13 1 European Union Restriction of Hazardous Substances RoHS Directive The European Union Restriction of Hazardous Substances RoHS Directive restricts the presence of chemical substances including Lead Cadmium Mercury Hexavalent Chromium PBB and PBDE in electronic products effective July 2006 This drive is manufactured with components and materials that comply with the RoHS Directive 2 13 2 China Restriction of Hazardous Substances RoHS Directive P E in NF lt This product has an Environmental Protection Use Period EPUP of 20 years The following table contains information mandated by China s Marking Requirements for Control of Pollution Caused by Electronic Information Products Standard 0 20 738 AEA EPU lt PR SRS Piae HEE gt Toxic or Hazardous Substances or Elements sti SH RE Hexavalent Polybrominated Polybrominated F i i Diphenyl Diphery Ether Name of Parts A LRR Bid RE 2 PBDE O indicates the hazardous and toxic s
38. ubstance content of the part at the homogenous material level is lower than the threshold defined by the China RoHS MCV Standard OU AMT FAR ime E Br BJ 6 UE KT rRBIRoHS MCV Oni FTE X indicates the hazardous and toxic substance content of the part at the homogenous material level is over the threshold defined by the China RoHS MCV Standard XUN Ia F FARM mE ME KERAMA df RoHS MCV Pai Pre X BJ TAE 2 14 CORROSIVE ENVIRONMENT Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases chlorine and nitric oxide classes G and H per ASTM B845 However this accelerated testing cannot duplicate every potential application environment Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment The silver copper nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide chloride and nitrate contaminants Sulfur is found to be the most damaging In addition electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly PCBA or exposed to an ambient relative humidity greater than 95 Materials used in cabinet fabrication such as vulcanized rubber that can outgas corrosi
39. usiness hours Authorized Service Centers For information regarding Warranty Support visit http www seagate com support warranty and replacements For information regarding data recovery services visit http www seagate com services software data recovery services For Seagate OEM and Distribution partner portal visit http www seagate com partners For Seagate reseller portal visit http www seagate com partners my spp dashboard Seagate Laptop Ultrathin HDD SATA Product Manual Rev A 1 1 0 INTRODUCTION This manual describes the functional mechanical and interface specifications for the following Seagate Laptop Ultrathin HDD SATA model drives Standard models Standard SED models ST500LT032 1E9142 ST500LT033 1ED142 ST320LT030 1E914C ST320LT031 1ED14C Previous generations of Seagate Self Encrypting Drive models were called Full Disk Encryption FDE models before a differentiation between drive based encryption and other forms of encryption was necessary The Self Encrypting Drive models indicated on the cover of this product manual have provisions for Security of Data at Rest based on the standards defined by the Trusted Computing Group see www trustedcomputinggroup org These drives provide the following key features 5400 RPM spindle speed 16MB buffer Quiet operation Fluid Dynamic Bearing FDB motor High instantaneous burst data transfer rates up to 6
40. ve compounds should be minimized or eliminated The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide free alternatives SEAGATE LAPTOP ULTRATHIN HDD SATA PRODUCT MANUAL REV A 13 CONFIGURING AND MOUNTING THE DRIVE 3 0 CONFIGURING AND MOUNTING THE DRIVE This section contains the specifications and instructions for configuring and mounting the drive 3 1 HANDLING AND STATIC DISCHARGE PRECAUTIONS After unpacking and before installation the drive may be exposed to potential handling and electrostatic discharge ESD hazards Observe the following standard handling and static discharge precautions Keep the drive in the electrostatic discharge ESD bag until you are ready for installation to limit the drive s exposure to ESD Before handling the drive put on a grounded wrist strap or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet Wear a grounded wrist strap throughout the entire installation procedure Handle the drive by its edges or frame only The drive is extremely fragile handle it with care Do not press down on the drive top cover Always rest the drive on a padded antistatic surface until you mount it in the computer Do not touch the connector pins or the printed circuit board Do not remove the factory installed labels from the drive or cover them with additional labels Removal voids the wa
Download Pdf Manuals
Related Search