Beko WMB71231
Contents
1. Pause button First the machine will drain the water inside of it Then it will spin the laundry with the set spin speed and drain the water coming out of them If you wish to drain only the water without spinning your laundry select the Pump Spin programme and then select the No Spin function with the help of Spin Speed Adjustment button Press Start Pause button i Use a lower spin speed for delicate laundries Temperature selection Whenever a new programme is selected the maximum temperature for the Selected programme appears on the temperature indicator To decrease the temperature press the Temperature Adjustment button Temperature will decrease gradually i If the programme has not reached the heating step you can change the temperature without switching the machine to Pause mode Spin speed selection Whenever a new programme is selected the recommended spin speed of the Selected programme is displayed on the spin speed indicator To decrease the spin speed press the Spin Speed Adjustment button Spin speed decreases gradually Then depending on the model of the product Rinse Hold and No Spin options appear on the display See Auxiliary function selection section for explanations of these options If the programme has not reached the spinning step you can change the speed without switching the machine to Pause mode 21 EN Programme and consumption table Auxiliary2. 17 EN Tips for efficient washing Soiling Level Heavily Soiled difficult stains such as grass Normally Soiled For example Lightly Soiled No visible stains exist Light colours and whites Recommended emperature range based on soiling evel 40 900 It may be necessary to pre reat the stains of perform prewash Powder and iquid detergents recommended or whites can b Clothes Colors Dark colors Recommended temperature range based on soiling level cold 400 Powder and iquid detergents recommended for colours can be used at dosages recommended for used at dosages recommended or heavily soiled clothes It is recommended O use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches Powder and liquid detergents heavily soiled clothes t is recommended O use powder detergents to clean and soil stains sensitive to bleaches Use detergents without bleach Powder and liquid detergents recommended for recommended for whites can be used at dosages recommended for normally soiled clothes Powder and liquid detergents colours can be used at dosages recommended for normally soiled clothes Use detergents without bleach Powder and liquid detergents recommended for recommended for whites can be used at dosages recommended for lightly soiled clothes colours can be used at dosage
3. Do not mix the bleaching agent and the detergent with each other Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum e Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum Odours and bacteria layers are formed on the drum as a result of continuous washing at lower temperatures and or in short programmes gt gt gt Leave the detergent drawer as well as the loading door of the machine ajar after each washing Thus a humid environment favorable for bacteria cannot occur in the machine Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum 33 EN Excessive laundry was loaded in gt gt gt Do not load the machine in excess Detergent in use is damp gt gt gt Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures A higher temperature is selected gt gt gt Select the proper programme and temperature according to the type and soiling degree of the laundry Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum The amount brand and storage conditions of the detergent used are inappropriate gt gt gt Use a deterge
4. This product is designed to resume operating in the event of powering on after a power interruption If you wish to cancel the programme see Cancelling the programme section e Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Do not neglect to have the grounding installation made by a qualified electrician Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations e The water supply and draining hoses must be securely fastened and remain undamaged Otherwise there is the risk of water leakage 6 EN Never open the loading door or remove the filter while there is still water in the drum Otherwise risk of flooding and injury from hot water will occur Do not force open the locked loading door The loading door will be ready to open just a few minutes after the washing cycle comes to an end In case of forcing the loading door to open the door and the lock mechanism may get damaged Unplug the product when not in use Never wash the product by spreading or pouring water onto it There is the risk of electric shock Never touch the plug with wet hands Never unplug by pulling on the cable always pull out by grabbing the plug Use detergents softeners and supplements suitable for washing machines only Follow the instructions on the textile tags an
5. gt gt Washing time is prolonged to avoid poor washing results when the supply voltage is low e Input temperature of water might be low gt gt gt Required time to heat up the water extends in cold seasons Also washing time can be lengthened to avoid poor washing results e Number of rinses and or amount of rinse water might have increased gt gt gt Machine increases the amount of rinse water when good rinsing is needed and adds an extra rinsing step if necessary e Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage Use recommended amount of detergent i Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment Laundry should be rearranged and re spun e Timer may stop during water intake gt gt gt Timer indicator will not countdown until the machine takes in adequate amount of water The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water Timer indicator will resume countdown after this e Timer may stop during heating step gt gt gt Timer indicator will not countdown until the machine reaches the selected temperature e Timer may stop during spinning step gt gt gt Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the
6. laundry in the arum i Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment Laundry should be rearranged and re spun e There might be an imbalance of laundry in the machine gt gt gt Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum i Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment Laundry should be rearranged and re spun 32 EN e There might be an imbalance of laundry in the machine gt gt gt Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the arum i Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment Laundry should be rearranged and re spun The machine will not spin if water is not drained completely gt gt gt Check the filter and the draining hose Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage Use recommended amount of detergent Insufficient amount of detergent was used over a long period of time gt gt gt U
7. the hoses are connected tightly Plug in your machine Turn the tap on completely Place the laundry in the machine Add detergent and fabric softener gie selection Select the programme suitable for the type quantity and soiling degree of the laundry in accordance with the Programme and consumption table and the temperature table below QT Ooh Heavily soiled white cottons and linens coffee table 90 C covers tableclothes towels bed sheets etc Normally soiled coloured fade proof cottons or synthetic 60 C clothes shirt nightgown pajamas etc and lightly soiled white linens underwear etc 40 C Blended laundry including 30 C delicate textile veil curtains Cold etc synthetics and woolens 19 EN 2 Select the desired programme with the Programme Selection button i Programmes are limited with the highest spin speed appropriate for that particular type of fabric i When selecting a programme always consider the type of fabric colour degree of soiling and permissible water temperature i Always select the lowest required temperature Higher temperature means higher power consumption i For further programme details see Programme and consumption table Main programmes Depending on the type of fabric use the following main programmes Cottons Use this programme for your cotton laundry such as bed sheets duvet and pillowcase sets towels b
8. the product at least 1 cm away from the edges of other furniture Removing packaging reinforcement Tilt the machine backwards to remove the packaging reinforcement Remove the Poule d reinforcement by pulling the ribbon Removing the transportation locks Do not remove the transportation locks before taking out the packaging reinforcement Remove the transportation safety bolts before operating the washing machine otherwise the product will be damaged 1 Loosen all the bolts with a spanner until they rotate freely C 2 Remove transportation safety bolts by turning them gently 8 EN 3 Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel P c P S i Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future i Never move the product without the transportation safety bolts properly fixed in place Connecting water supply i The water supply pressure required to run the product is between 1 to 10 bars 0 1 10 MPa It is necessary to have 10 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly Attach a pressure reducing valve if water pressure is higher i If you are going to use the double water inlet product as a single cold water inlet unit you must install the supplied stopper to the hot water valve before operating th
9. washing 18 5 Operating the product 19 Control panel 2000085 19 Preparing the machine 19 Programme selection 19 Main programmes Additional programmes 20 Special programmes 4 21 Temperature selection 21 Spin speed selection 00 21 Programme and consumption table 22 Auxiliary function selection 24 Starting the programme 25 CHI LOCK sb d e tac 25 Progress of programme 26 Loading door lock 26 Changing the selections after programme has started ss anaia msa aamini ni 26 Canceling the programme 26 End of programme 27 6 Maintenance and cleaning28 Cleaning the detergent drawer 28 Cleaning the loading door and the QUM Gedeon e eda 28 Cleaning the body and control panel 28 Cleaning the water intake filters 28 Draining remaining water and cleaning the pump filter ccce 29 7 Troubleshooting 31 8 Guarantee 37 9 Service 38 Your washing machine Overview 1 Power cable 5 Adjustable feet 2 Top panel 6 Loading door 3 Control panel 7 Detergent drawer 4 Filter cap 8 Drain hose 4 EN Technical specifications Modes WMB71231B WMB712318 WMB71231W eae ME MM ME NUNG CD Height cm Width cm Depth cm Net waht SG eae i Technical specifications may be changed with
10. will continue running To activate the Child Lock Press and hold 1 and 2 Auxiliary Function buttons for 3 seconds The lights on the 1 and 2 Auxiliary Function buttons will flash and COS CO2 CO1 will appear on the display respectively while you keep the buttons pressed for 3 seconds Then Con will appear on the display indicating that the Child Lock is activated If you press any button or turn the Programme Selection knob when the Child Lock is active same phrase will appear on the display The lights on the 1st and 2nd auxiliary function buttons that are used to deactivate the Child Lock will blink 3 times To deactivate the Child Lock Press and hold 1 and 2 auxiliary function buttons for 3 seconds while any programme is running The lights on the 1 and 2 Auxiliary Function buttons will flash and COS CO2 CO1 will 25 EN appear on the display respectively while you keep the buttons pressed for 3 seconds Then COFF will appear on the display indicating that the Child Lock is deactivated i In addition to the method above to deactivate the Child Lock switch the Programme Selection knob to On Off position when no programme is running and select another programme i Child Lock is not deactivated after power failures or when the machine is unplugged Progress of programme Progress of a running programme can be followed from the Programme Follow up indicator
11. At the beginning of every programme step the relevant indicator light will turn on and light of the completed step will turn off You can change the auxiliary functions speed and temperature settings without stopping the programme flow while the programme is running To do this the change you are going to make must be in a step after the running programme step If the change is not compatible relevant lights will flash for 3 times If the machine does not pass to the spinning step Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the machine Loading door lock There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable Loading door light will start flashing when the machine is switched to Pause mode Machine checks the level of the water inside If the level is suitable Loading Door light illuminates steadily within 1 2 minutes and the loading door can be opened If the level is unsuitable Loading Door light turns off and the loading door cannot be opened If you are obliged to open the Loading Door while the Loading Door light is off you have to cancel the current programme see Canceling the programme Changing the selections after programme has started Switching the machine to pause mode Press the Start Pause butto
12. BEKO Automatic washing machine WMB71231B WMB71231S WMB71231W 2820521853 070211 1601 Please read this user manual first Dear Customer We hope that you get the best results from the product which has been manufactured in state of the art plants and passed through a strict quality control procedure Therefore please read the entire user manual carefully before using the product and keep it as a reference for future use In case of transferring the product to someone else give the manual as well The user manual will help you use your machine in a fast and safe way e Read the user manual before installing and starting your product Always follow the safety instructions Keep this user manual within easy reach for future reference e Read also the other documents supplied with the product Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this user manual the following symbols are used i Important information or useful hints about usage A Warning for hazardous situations with regard to life and property A Warning for electric shock This appliance s packaging material is recyclable Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose Your appliance also contains a great amount of recyclable material It is marked with thi
13. The amount of washing detergent to be used depends on the amount of laundry the degree of soiling and water hardness Read the manufacturer s instructions on the detergent package carefully and follow the dosage values e Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam poor rinsing financial savings and finally environmental protection e Use lesser detergent for small amounts or lightly soiled clothes e Use concentrated detergents in the recommended dosage Using softeners Pour the softener into the softener compartment of the detergent drawer e Use the dosages recommended on the package e Do not exceed the max level marking in the softener compartment e fthe softener has lost its fluidity dilute it with water before putting it in the detergent drawer Using liquid detergents If the product contains a liquid detergent cup e Make sure that you have placed the liquid detergent cup in compartment nr ll e Use the detergent manufacturer s measuring cup and follow the instructions on the package e Use the dosages recommended on the package e If the liquid detergent has lost its fluidity dilute it with water before EN putting in the detergent cup If the product does not contain a Maus detergent cup Do not use liquid detergent for the prewash in a programme with prewash Use the deterge
14. ain hose must be directly connected to the wastewater drain or to the washbasin Your house will be flooded if the hose comes out of its housing during water discharge Moreover there is risk of scalding due to high washing temperatures To prevent Such situations and to ensure smooth water intake and discharge of the machine fix the end of the discharge hose tightly so that it cannot come out e The hose should be attached to a height of at least 40 cm and 100 cm at most e Incase the hose is elevated after laying it on the floor level or close to the ground less than 40 cm above the ground water discharge becomes more difficult and the laundry may come out excessively wet Therefore follow the heights described in the figure e To prevent flowing of dirty water back into the machine and to allow for easy discharge do not immerse the hose end into the dirty water or drive it in the drain more than 15 cm If it is too long cut it short e The end of the hose should not be bent it should not be stepped on and the hose must not be pinched between the drain and the machine e If the length of the hose is too short use it by adding an original extension hose Length of the hose may not be longer than 3 2 m To avoid water leak failures the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak Adjusting the feet In ord
15. at the electricity tap water Supply and water drainage systems are appropriate before calling the Authorized Service Agent If they are not call a qualified technician and plumber to have any necessary arrangements carried out Preparation of the location and electrical tap water and waste water installations at the place of installation is under customer s responsibility Installation and electrical connections of the product must be carried out by the Authorized Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons Prior to installation visually check if the product has any defects on it If SO do not have it installed Damaged products cause risks for your safety Make sure that the water inlet and discharge hoses as well as the power cable are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures Appropriate installation location e Place the machine on a rigid floor Do not place it on a long pile rug or similar surfaces e Total weight of the washing machine and the dryer with full load when they are placed on top of each other reaches to approx 180 kilograms Place the product on a solid and flat floor that has sufficient load carrying capacity e Do not place the product on the power cable e Do not install the product at places where temperature may fall below O C e Place
16. athrobes underwear etc Your laundry will be washed with vigorous washing action for a longer washing cycle Synthetics Use this programme to wash your synthetic clothes shirts blouses synthetic cotton blends etc It washes with a gentle action and has a shorter washing cycle compared to the Cottons programme For curtains and tulle use the Synthetic 40 C programme with prewash and anti creasing functions selected As their meshed texture causes excessive foaming wash the veils tulle by putting little amount of detergent into the main wash compartment Do not put detergent in the prewash compartment Woollens Use this programme to wash your woolen clothes Select the appropriate temperature complying with the tags of your clothes Use appropriate detergents for woolens Additional programmes For special cases additional programmes are available in the machine i Additional programmes may differ according to the model of the machine Cottons Eco You may wash your normally soiled durable cotton and linen laundry in this programme with the highest energy and water saving compared to all other wash programmes suitable for cottons Actual water temperature may differ from the declared cycle temperature Programme duration may automatically be shortened during later stages of the programme if you wash less amount e g 2 capacity or less of laundry In this case energy and water consumption will be f
17. continuously to notify that the 26 EN programme has been canceled Pump function is activated for 1 2 minutes regardless of the programme step and whether there is water in the machine or not After this period your machine will be ready to start with the first step of the new programme i Depending on the step where the programme was canceled in you may have to put detergent and softener again for the programme you have selected anew End of programme End appears on the display at the end of the programme 1 Wait until the loading door light illuminates steadily 2 Press On Off button to switch off the machine 3 Take out your laundry and close the loading door Your machine is ready for the next washing cycle 27 EN Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals Cleaning the detergent drawer Clean the detergent drawer at regular intervals every 4 5 washing cycles as shown below in order to prevent accumulation of powder detergent in Ly 1 Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine i If more than normal amount of water and softener mixture starts to gather in the softener compartment the siphon must be cleaned 2 Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbas
18. crapers cutlery baskets filters and light bulbs e Repairs required as a result of unauthorised repair or inexpert installation that fails to meet the requirements contained in the user instruction book e Repairs to products used on commercial or non residential household premises e Loss of frozen food in freezers or fridge freezers Food loss insurance is often included within your household contents insurance policy or may be available separately from your retailer Important notes e Your Beko product is designed and built for domestic household use only e The guarantee will be void if the product is installed or used in commercial or non residential domestic household premises e The product must be correctly installed located and operated in accordance with the instructions contained in the User Instructions Booklet provided e Professional installation by a qualified Electrical Domestic Appliance Installer is recommended for all Washing Machines Dishwashers and Electric Cookers e Gas Cookers must only be installed by a CORGI or BORD GAIS registered Gas Installer e The guarantee is given only within the boundaries of the United Kingdom and the Republic of Ireland e The guarantee is applicable only to new products and is not transferable if the product is resold e Beko disclaims any liability for incidental or consequential damages e The guarantee does not in anyway diminish your statutory or lega
19. d on the detergent package The product must be unplugged during installation maintenance cleaning and repairing procedures Always have the installation and repairing procedures carried out by the Authorized Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons Intended use This product has been designed for domestic use It is not suitable for commercial use and it must not be used out of its intended use The product must only be used for washing and rinsing of laundry that are marked accordingly The manufacturer waives any responsibility arisen from incorrect usage or transportation The service life of your product is 10 years During this period original spare parts will be available to operate the appliance properly Children s safety e Electrical products are dangerous for the children Keep children away from the product when it is in use Do not let them to tamper with the product Use child lock to prevent children from intervening with the product e Do not forget to close the loading door when leaving the room where the product is located e Store all detergents and additives in a safe place away from the reach of the children 7 EN Installation Refer to the nearest Authorised Service Agent for installation of the product To make the product ready for use review the information in the user manual and make sure th
20. dry the degree of soiling and the washing programme desired The machine automatically adjusts the amount of water according to the weight of the loaded laundry Follow the information in the Programme and consumption table When overloaded machine s washing performance will drop Moreover noise and vibration problems may occur Laundry types and their average weights in the following table are given as examples Laundry type Weight g Bathrobe 1200 Napkin 100 Duvet cover 700 Bed Sheet 500 Pillowcase 200 Tablecloth 250 Towel 200 Hand towel 100 Evening gown 200 Underclothing 100 Men s overalls 600 Men s shirt 200 Men s pajamas 500 Blouses 100 Loading the laundry e Open the loading door e Place laundry items loosely into the machine e Push the loading door to close until you hear a locking sound Ensure that no items are caught in the door i The loading door is locked while a programme is running The door can only be opened a while after the programme comes to an end In case of misplacing the laundry noise and vibration problems may occur in the machine 14 EN Using detergent and softener Detergent Drawer The detergent drawer is composed of three compartments I for prewash Il for main wash Ill for softener in addition there is siphon piece in the softener compartment Tel Tono ry Wwe i The deterge
21. during rinsing or softener step Wash and clean the dispenser with hot water Put the detergent in the correct compartment Detergent might be mixed with the softener gt gt gt Do not mix the softener with detergent Wash and clean the dispenser with hot water Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum 34 EN Detergent is put in wet drawer gt gt gt Dry the detergent drawer before putting in detergent Detergent has gotten damp gt gt gt Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures Water pressure is low gt gt gt Check the water pressure The detergent in the main wash compartment got wet while taking in the prewash water Holes of the detergent compartment are blocked gt gt gt Check the holes and clean if they are clogged There is a problem with the detergent drawer valves gt gt gt Call the Authorized Service Agent Detergent might be mixed with the softener gt gt gt Do not mix the softener with detergent Wash and clean the dispenser with hot water Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum Excessive laundry was loaded in gt gt gt Do not load the machine in excess Wrong programme and temperature were selected gt gt gt Select the pr
22. e Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case Take out all substances in the pockets Such as coins pens and paper clips and turn pockets inside out and brush Such objects may damage the product or cause noise problem Put small size clothes such as infant s Socks and nylon stockings in a laundry bag or pillow case Place curtains in without compressing them Remove curtain attachment items Fasten zippers sew loose buttons and mend rips and tears Wash machine washable or hand washable labeled products only with an appropriate programme Do not wash colours and whites together New dark coloured cottons release a lot of dye Wash them Separately Tough stains must be treated properly before washing If unsure check with a dry cleaner Use only dyes colour changers and limescale removers suitable for machine wash Always follow the instructions on the package Wash trousers and delicate laundry turned inside out Keep laundry items made of Angora wool in the freezer for a few hours before washing This will reduce pilling Laundry that are subjected to materials such as flour lime dust milk powder etc intensely must be shaken off before placing into the machine Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage Correct load capacity The maximum load capacity depends on the type of laun
23. e pump filter is clogged Filter must be cleaned whenever it is clogged or in every 3 months Water must be drained off first to clean the pump filter In addition prior to transporting the machine eg when moving to another house and in case of freezing of the water water may have to be drained completely Foreign substances left in the pump filter may damage your machine or may cause noise problem In order to clean the dirty filter and discharge the water 1 Unplug the machine to cut off the supply power A Temperature of the water inside the machine may rise up to 90 C To avoid burning risk filter must be cleaned after the water in the machine cools down 2 Open the filter cap If the filter cap is composed of two pieces press the tab on the filter cap downwards and pull the piece out towards yourself If the filter cap is one piece pull the cap from both sides at the top to open AS i You can remove the filter cover by slightly pushing downwards with a thin plastic tipped tool through the gap above the filter cover Do not use metal tipped tools to remove the cover 3 Some of our products have emergenoy draining hose and some does not have Follow the steps below to discharge the water Discharging the water when the product has an emergenoy draining hose 29 EN a Pull the emergency draining hose out from its seat b Place a large container at the end of the hose Drain th
24. e product Applies for the products supplied with a blind stopper group i If you want to use both water inlets of the product connect the hot water hose after removing the stopper and gasket group from the hot water valve Applies for the products supplied with a blind stopper group Models with a single water inlet should not be connected to the hot water tap In such a case the laundry 9 EN 1 will get damaged or the product will Switch to protection mode and will not operate Do not use old or used water inlet hoses on the new product It may cause stains on your laundry Connect the special hoses supplied with the product to the water inlets on the product Red hose left max 90 C is for hot water inlet blue hose right max 25 C is for cold water inlet Ze A Ensure that the cold and hot water connections are made correctly when installing the product Otherwise your laundry will come out hot at the end of the washing process and wear out Tighten all hose nuts by hand Never use a wrench when tightening the nuts Open the taps completely after making the hose connection to check for water leaks at the connection points If any leaks occur turn off the tap and remove the nut Retighten the nut carefully after checking the seal To prevent water leakages and damages caused by them keep the taps closed when the machine is not in use Connecting to the drain e The end of the dr
25. e water into the container by pulling out the plug at the end of the hose When the container is full block the inlet of the hose by replacing the plug After the container is emptied repeat the above procedure to drain the water in the machine completely c When draining of water is finished close the end by the plug again and fix the hose in its place d Turn the pump filter to take it out Discharging the water when the product does not have an emergency draining hose P a Place a large container in front of the filter to catch water from the filter b Loosen pump filter anticlockwise until water starts to flow Fill the flowing water into the container you have placed in front of the filter Always keep a piece of cloth handy to absorb any spilled water c When the water inside the machine is finished take out the filter completely by turning it 4 Clean any residues inside the filter as well as fibers if any around the pump impeller region 5 Install the filter If your product has a water jet feature be sure to fit the filter into its housing in the pump Never force the filter 30 EN while installing it into its housing Seat the filter into its place completely Otherwise water may leak from the filter cap If the filter cap is composed of two pieces close the filter cap by pressing on the tab If it is one piece seat the tabs in the lower part into their places first and then press
26. ed on the package Do not use softener and starch together in a washing cycle Wipe the inside of the machine with a damp and clean cloth after using starch Using bleaches Select a programme with prewash and add the bleaching agent at the beginning of the prewash Do not put detergent in the prewash compartment As an alternative application select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step Do not use bleaching agent and detergent by mixing them Use just a little amount approx 50 ml of bleaching agent and rinse the clothes very well as it causes skin irritation Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes When using oxygen based bleaches follow the instructions on the package and select a programme that washes at a lower temperature e Oxygen based bleaches can be used together with detergents however if its thickness is not the same with the detergent put the detergent first into the compartment nr Il in the detergent drawer and wait until the detergent flows while the machine is taking in water Add the bleaching agent from the same compartment while the machine is still taking in water Using limescale remover e When required use limescale removers manufactured specifically for washing machines only e Always follow instructions on the package
27. er to ensure that the product operates more silent and vibration free it must stand level and balanced on its feet Balance the machine by adjusting the feet Otherwise the product may move from its place and cause crushing and vibration problems 1 Loosen the lock nuts on the feet by hand 2 Adjust the feet until the product stands level and balanced 3 Tighten all lock nuts again by hand M Z Do not use any tools to loosen the lock nuts Otherwise they will get damaged Electrical connection Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Our company shall not be liable 10 EN for any damages that will arise when the product is used without grounding in accordance with the local regulations e Connection must comply with national regulations e Power cable plug must be within easy reach after installation e The voltage and allowed fuse or breaker protection are specified in the Technical specifications section If the current value of the fuse or breaker in the house is less than 13 Amps have a qualified electrician install a 13 Amp fuse e The specified voltage must be equal to your mains voltage e Do not make connections via extension cables or multi plugs N Damaged power cables must be replaced by the Authorized Service Agents Electrical requirements Before you insert the plug into the wall Soc
28. ety bolts Laundry quantity in the machine might be too little gt gt gt Add more laundry to the machine Machine might be overloaded with laundry gt gt gt Take out some of the laundry ied ris machine or distribute the load by hand to balance it homogenously in the machine Machine might be leaning on a rigid item gt gt gt Make sure that the machine is not leaning on anything Machine might have stopped temporarily due to low voltage gt gt gt t will resume running when the voltage restores to the normal level e Draining hose might not be at adequate height gt gt gt Connect the water draining hose as described in the operation manual i The water level is not visible from outside of the washing machine This is not a failure 31 EN e Door lock is activated because of the water level in the machine gt gt gt Drain the water by running the Pump or Spin programme e Machine is heating up the water or it is at the spinning cycle gt gt gt Wait until the programme completes e Child lock is engaged Door lock will be deactivated a couple of minutes after the programme has come to an end gt gt gt Wait for a couple of minutes for deactivation of the door lock e Water pressure is low gt gt gt Machine waits until taking in adequate amount of water to prevent poor washing quality due to the decreased amount of water Therefore the washing time extends e Voltage might be low gt
29. functions EN Programme Selectable temperature Buisea15 nuv 4D9edg XEN UM uonduunsuo 46u N y CAR di is e e s s s a s Q Q st S9 olol o Oo oO 6 oyu wo o j alaj o c lt amp amp amp ololeo es glIlglsisz z E lone ome kone ime Oe O _ EO S Baby amp Toddler Clothing eo 7 20 240 1600 BECUNNE Synthetics 22 EN e Selectable Automatically selected no canceling Energy Label programme EN 60456 Ed 3 If maximum spin speed of the machine is lower then this value you can only select up to the maximum spin speed See the programme description for maximum load o Water and power consumption may vary subject to the changes in water pressure water hardness and temperature ambient temperature type and amount of laundry selection of auxiliary functions and spin speed and changes in electric voltage i You can see the washing time of the programme you have selected on the display of the machine It is normal that small differences may occur between the time shown on the display and the real washing time 23 EN i The auxiliary functions in the table may vary according to the model of your machine Auxiliary function selection Select the desired auxiliary functions before starting the programme Furthermore you may also select or cancel auxiliary functions that are suitable to the running programme without pressing the Star
30. in Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning 3 Insert the drawer back into its place after cleaning and make sure that it is Seated well Cleaning the loading door and the drum Residues of softener detergent and dirt may accumulate in your machine in time and may cause unpleasant odours and washing complaints To avoid this use the Drum Cleaning programme If your machine is not featured with Drum Cleaning programme use Cottons 90 programme and select Additional Water or Extra Rinse auxiliary functions as well Before starting the programme put max 100 g of powder anti limescale into the main wash detergent compartment compartment nr Il If the anti limescale is in tablet form put only one tablet into compartment nr Il Dry the inside of the bellow with a clean piece of cloth after the rogramme has come to an end tj Repeat Drum Cleaning process in every 2 months i Use an anti limescale suitable for the washing machines After every washing make sure that no foreign substance is left in the drum If the holes on the bellow shown in the figure is blocked open the holes using a toothpick i Foreign metal substances in your machine will cause rust stains Clean the stains on the drum surface by using cleaning agents for stainless Steel Never use steel wool or wire wool Cleaning the body and control pane
31. is performed with more water 3096 and the pet hair is removed more effectively Never wash your pets in the washing machine Delayed Start With the Delayed Start function the startup of the programme may be delayed up to 19 hours Delayed start time can be increased by increments of 1 hour 24 EN i Do not use liquid detergents when you set Delayed Start There is the risk of staining of the clothes 1 Open the loading door place the laundry and put detergent etc 2 Select the washing programme temperature spin speed and if required the auxiliary functions 3 Set the desired time by pressing the Delayed Start button 4 Press Start Pause button The delayed start time you have set is displayed Delayed start countdown starts symbol next to the delayed start time moves up and down on the display i Additional laundry may be loaded during the delayed start period 5 Atthe end of the countdown duration of the selected programme will be displayed symbol will disappear and the selected programme will start Changing the Delayed Start period If you want to change the time during countdown 1 Press Delayed Start button Time will increase by 1 hour each time you press the button 2 lf you want to decrease the delayed start time press Delayed Start button repeatedly until the desired delayed start time appears on the display Canceling the Delayed Start function If you want to cancel the de
32. ket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply We recommend that this appliance be connected to the mains supply via a Suitable switched and fused socket in a readily accessible position Should the mains lead of the appliance become damaged or need replacing at any time it must be replaced by a special purpose made mains lead which can only be obtained from a Authorised Service Agent ZN This appliance must be earthed If the fitted moulded plug is not suitable for your socket then the plug should be cut off and an appropriate plug fitted Destroy the old plug which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house The moulded plug on this appliance incorporates a 13A fuse Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used Do not forget to refit the fuse cover In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug Fuse covers are available from any good electrical store Important Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug proceed as follo
33. l Wipe the body of the machine with Soapy water or non corrosive mild gel detergents as necessary and dry with a Soft cloth Use only a soft and damp cloth to clean the control panel Never use sponge or scrub materials These will damage the painted and plastic surfaces Cleaning the water intake filters There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap These filters prevent foreign substances and dirt in the water to enter the washing machine Filters should be 28 EN cleaned as they do get dirty Close the taps 2 Remove the nuts of the water intake hoses to access the filters on the water intake valves Clean them with an appropriate brush If the filters are too dirty take them out by means of pliers and clean them 3 Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water 4 Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand Draining remaining water and cleaning the pump filter The filter system in your machine prevents Solid items such as buttons coins and fabric fibers clogging the pump impeller during discharge of washing water Thus the water will be discharged without any problem and the service life of the pump will extend If the machine fails to drain water th
34. l rights Should you experience any difficulty in obtaining service please contact the Beko Customer Help Line Tel 0845 600 4911 e mail service beko co uk 37 EN E Service Please keep your purchase receipt or Service can be obtained at a charge other proof of purchase in a safe place you will need to have it should the product Should you experience any difficulty in require attention under guarantee obtaining service please contact the Beko Customer Help Line You should also complete the details Tel 0845 600 4911 below it will help us assist you when e mail service beko co uk requesting service The model number is printed on the Instruction Booklet and the serial number is printed on the Rating Label affixed to the appliance Model No Serial No Retailer Date of purchase For service under guarantee simply telephone the appropriate number below UK Mainland amp Northern Ireland Fridges amp Freezers 0845 600 4903 Electric Cookers 0845 600 4902 Gas amp 0845 600 4905 Dual Fuel Cookers Washing Machines amp 0845 600 4906 Dishwashers Republic of Ireland All Refrigeration 01 862 3411 All Cookers Washing Machines amp Dishwashers Before requesting service please check the trouble shooting guide in the Operating Instructions as a charge may be levied where no fault is found even though your product may still be under guarantee Service once the manufacturers guarantee has expired If y
35. layed start countdown and start the programme immediately 1 Set the Delayed Start period to zero or turn the Programme Selection knob to any programme Thus Delayed Start function will be canceled The End Cancel light flashes continuously 2 Then select the programme you want to run again 3 Press Start Pause button to start the programme Starting the programme 1 Press Start Pause button to start the programme 2 Programme follow up light showing the startup of the programme will turn on i If no programme is started or no key is pressed within 1 minute during programme selection process the machine will switch to Pause mode and the illumination level of the temperature speed and loading door indicator lights will decrease Other indicator lights and indicators will turn off Once the Programme Selection knob is rotated or any button is pressed indicator lights and indicators will turn on again Child Lock Use Child Lock function to prevent children from tampering with the machine Thus you can avoid any changes in a running programme i If the Programme Selection knob is turned when the Child Lock is active Con appears on the display The Child Lock does not allow any change in the programmes and the selected temperature speed and auxiliary functions i Even if another programme is selected with the Programme Selection knob while the Child Lock is active previously selected programme
36. manner E Washing water temperature Wash with sensitive short programmes Operate the product in the highest capacity allowed by the programme you have selected but do not overload see Programme and consumption table Always follow the instructions on the detergent packaging Wash slightly soiled laundry at low temperatures Use faster programmes for small quantities of lightly soiled laundry Do not use prewash and high temperatures for laundry that is not heavily soiled or stained If you plan to dry your laundry in a dryer select the highest spin speed recommended during washing process Do not use detergent in excess of the amount recommended on the detergent package Sorting the laundry Sort laundry according to type of fabric colour and degree of soiling and allowable water temperature Always obey the instructions given on the garment tags 13 EN P De Do not use bleach w o 8 93 o ag 3 c o ji et Suitable for drier Do not dry with drier E B n be ironed with hot iron Hang without spinning amp ik Non machine washable e Dry cleanable Do not dry clean a K Dry horizontally o 3 o 3 m En D 5 a 2 BJ X Can be ironed Do not iron with warm iron Preparing laundry for washing Laundry items with metal attachments such as underwired bras belt buckles or metal buttons will damage the machin
37. n to switch the machine to pause mode while a programme is running The light of the Step which the machine is in starts flashing in the Programme Follow up indicator to show that the machine has been switched to the pause mode Also when the loading door is ready to be opened Loading Door light will also illuminate continuously in addition to the programme step light Changing the speed and temperature settings for auxiliary functions Depending on the step the programme has reached you may cancel or activate the auxiliary functions see Auxiliary function selection You may also change the speed and temperature settings see Spin speed selection and Temperature selection If no change is allowed the relevant light will flash for 3 times Adding or taking out laundry 1 Press the Start Pause button to Switch the machine to pause mode The programme follow up light of the relevant step during which the machine was switched into the pause mode will flash 2 Wait until the Loading Door can be opened 3 Open the Loading Door and add or take out the laundry 4 Close the Loading Door 5 Make changes in auxiliary functions temperature and speed settings if necessary 6 Press Start Pause button to start the machine Canceling the programme To cancel the programme turn the Programme Selection knob to select another programme Previous programme will be canceled End Cancel light will flash
38. nt a may be in two different types according to the model of your machine as seen above Detergent softener and other cleaning agents e Add detergent and softener before starting the washing programme e Never open the detergent drawer while the washing programme is running e When using a programme without prewash do not put any detergent into the prewash compartment compartment nr e na programme with prewash do not put liquid detergent into the prewash compartment compartment nr e Do not select a programme with prewash if you are using a detergent bag or dispensing ball Place the detergent bag or the dispensing ball directly among the laundry in the machine e f you are using liquid detergent do not forget to place the liquid detergent cup into the main wash compartment compartment nr Il Choosing the detergent type The type of detergent to be used depends on the type and colour of the fabric e Use different detergents for coloured and white laundry 15 e Wash your delicate clothes only with special detergents liquid detergent wool shampoo etc used solely for delicate clothes e When washing dark coloured clothes and quilts it is recommended to use liquid detergent e Wash woolens with special detergent made specifically for woolens A Use only detergents manufactured specifically for washing machines Do not use soap powder Adjusting detergent amount
39. nt appropriate for the washing machine and your laundry Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures Detergent is put in the wrong compartment gt gt gt f detergent is put in the prewash compartment although prewash cycle is not selected machine can take this detergent during rinsing or softener step Put the detergent in the correct compartment Pump filter is clogged Check the filter Drain hose is folded gt gt gt Check the drain hose Insufficient amount of detergent is used gt gt gt Using insufficient amount of detergent for the water hardness can cause the laundry to become stiff in time Use appropriate amount of detergent according to the water hardness Detergent is put in the wrong compartment gt gt gt f detergent is put in the prewash compartment although prewash cycle is not selected machine can take this detergent during rinsing or softener step Put the detergent in the correct compartment Detergent might be mixed with the softener gt gt gt Do not mix the softener with detergent Wash and clean the dispenser with hot water Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum Detergent is put in the wrong compartment gt gt gt f detergent is put in the prewash compartment although prewash cycle is not selected machine can take this detergent
40. nt manufacturer s measuring cup and follow the instructions on the package Liquid detergent stains your clothes when used with Delayed Start function If you are going to use the Delayed Start function do not use liquid detergent Using gel and tablet detergent When using tablet gel etc detergents read the manufacturer s instructions on the detergent package carefully and follow the dosage values If there is not any instruction on the package apply the following If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup put the gel detergent into the main wash detergent compartment during first water intake If your machine contains a liquid detergent cup fill the detergent into this cup before starting the programme If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet put it directly into the drum before washing Put tablet detergents into the main wash compartment compartment nr Il or directly into the drum before washing 16 EN i Tablet detergents may leave residues in the detergent compartment If you encounter such a case place the tablet detergent between the laundry close to the lower part of the drum in future washings i Use the tablet or gel detergent without selecting the prewash function Using starch Add liquid starch powder starch or the dyestuff into the softener compartment as instruct
41. ogramme and consumption table When you use additional chemicals stain removers bleaches and eto reduce the amount of detergent Laundry remains wet at the end of the programme e Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage Use recommended amount of detergent i Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment Laundry should be rearranged and re spun A If you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorized Service Agent Never try to repair a nonfunctional product yourself 36 EN B Guarantee Your new Beko product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase What is covered e Repairs necessary as a result of faulty materials defective components or manufacturing defect e The cost of functional replacement parts but excluding consumable items e The labour costs of a Beko approved repairer to carry out the repair What is not covered e Transit delivery or accidental damage or misuse and abuse e Cabinet or appearance parts including knobs flaps handles or container lids e Accessories or consumable items including but not limited to ice trays s
42. oper programme and temperature for the laundry to be washed pide aa was used gt gt gt Select the proper detergent for the laundry to be washed Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum Improper detergents for the washing machine are being used gt gt gt Use detergents appropriate for the washing machine Excessive amount of detergent is used gt gt gt Use only sufficient amount of detergent Detergent was stored under improper conditions gt gt gt Store detergent in a closed and dry location Do not store in excessively hot places Some meshed laundry such as tulle may foam too much because of their texture gt gt gt Use smaller amounts of detergent for this type of item Detergent is put in the wrong compartment gt gt gt Put the detergent in the correct compartment Softener is being taken early gt gt gt There may be problem in the valves or in the detergent dispenser Call the Authorized Service Agent Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum 35 EN e Too much detergent is used gt gt gt Mix 1 tablespoonful softener and 12 water and pour into the main wash compartment of the detergent drawer i Put detergent into the machine suitable for the programmes and maximum loads indicated in the Pr
43. ou have purchased an extended guarantee please refer to the instructions contained within the extended guarantee agreement document Otherwise please call the appropriate number above where 38 EN 39 EN BEKO Beko plc Beko House Caxton Way Watford Hertfordshire WD18 8UF Tel 0845 6004911 Fax 0845 6004922 Email service 9 beko co uk www beko co uk
44. out prior notice to improve the quality of the product Figures in this manual are schematic and may not match the product exactly i Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards Depending on operational and environmental conditions of the product these values may vary 5 EN El Important safety instructions This section contains safety instructions that will help protect from risk of personal injury or property damage Failure to follow these instructions shall void any warranty General safety e This product should not be used by persons with physical sensory or mental disorders or unlearned or inexperienced people including children unless they are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product e Never place the product on a carpet covered floor otherwise lack of airflow beneath the machine will cause electrical parts to overheat This will cause problems with your product e Do not operate the product if the power cable plug is damaged Call the Authorized Service Agent e Have a qualified electrician connect a 16 Ampere fuse to the installation location of the product e If the product has a failure it should not be operated unless it is repaired by the Authorized Service Agent There is the risk of electric shock e
45. s recommended for lightly soiled clothes Use detergents without bleach 18 EN he stains that are Recommended temperature range based on solling level cold 400 Liquid detergents suitable for colours and dark colours can be used at dosages recommended for heavily soiled clothes Liquid detergents suitable for colours and dark colours can be used at dosages recommended for normally soiled clothes Liquid detergents suitable for colours and dark colours can be used at dosages recommended for lightly soiled clothes Delicates Woolens Silks Recommended temperature range based on soiling level cold 30C Prefer liquid detergents produced for delicate clothes Woollen and silk clothes must be washed with Special woollen detergents Prefer liquid detergents produced for delicate clothes Woollen and silk clothes must be washed with special woollen detergents Prefer liquid detergents produced for delicate clothes Woollen and silk clothes must be washed with special woollen detergents Operating the product Control panel 1 Programme Selection knob Uppermost position On Off 2 Display 3 Delayed Start button 4 Programme Follow up indicator 5 Start Pause button 6 Auxiliary Function buttons 7 Spin Speed Adjustment button 8 Temperature Adjustment button Preparing the machine 1 Make sure that
46. s label to indicate the used appliances that should not be mixed with other waste This way the appliance recycling organised by your EE Manufacturer will be done under the best possible conditions in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment Contact your town hall or your retailer for the used appliance collection points closest to your home We thank you doing your part to protect the environment 2 EN TABLE OF CONTENTS 1 Your washing machine 4 OVENS e beca Ne d eta s 4 Technical specifications 5 2 Important safety instructions 6 General safety o n anaana 6 Intended US 2 2 eee eee 6 Children s safety 2 T 3 Installation 8 Appropriate installation location 8 Removing packaging reinforcement 8 Removing the transportation locks 8 Connecting water supply 9 Connecting to the drain 10 Adjusting the feet 0 10 Electrical connection 10 FIKSE USE ce s dore E PR RR 12 Disposing of packaging material 12 Transportation of the product 12 Disposing of the old product 12 4 Preparation 13 Things to be done for energy saving 13 Sorting the laundry 13 Preparing laundry for washing 13 Correct load capacity 14 Loading the laundry 14 Using detergent and softener 15 Tips for efficient
47. se the recommended amount of detergent appropriate for water hardness and the laundry Washing was made at low temperatures for a long time over a long period of time gt gt gt Select the proper temperature for the laundry to be washed Insufficient amount of detergent is used with hard waters gt gt gt Using insufficient amount of detergent with hard water causes the soil to stick on the cloth and this turns the cloth into gray in time It is difficult to eliminate graying once it happens Use the recommended amount of detergent appropriate for water hardness and the laundry Too much detergent is used gt gt gt Use the recommended amount of detergent appropriate for water hardness and the laundry Regular drum cleaning is not applied gt gt gt Clean the drum regularly For this please see Cleaning the loading door and the drum Insufficient amount of detergent is used gt gt gt Use recommended amount of detergent appropriate for the laundry Excessive laundry was loaded in gt gt gt Do not load the machine in excess Load with amounts recommended in the Programme and consumption table Wrong programme and temperature were selected gt gt gt Select the proper programme and temperature for the laundry to be washed Wrong type of detergent is used gt gt gt Use original detergent appropriate for the machine Detergent is put in the wrong compartment gt gt gt Put the detergent in the correct compartment
48. t Pause button when the machine is operating For this the machine must be in a step before the auxiliary function you are going to select or cancel If the auxiliary function cannot be selected or canceled light of the relevant auxiliary function will blink 3 times to warn the user i Some functions cannot be selected together If a second auxiliary function conflicting with the first one is selected before starting the machine the function selected first will be canceled and the second auxiliary function selection will remain active For example if you want to select Quick Wash after you have selected the Prewash Prewash will be canceled and Quick Wash will remain active i An auxiliary function that is not compatible with the programme cannot be selected See Programme and consumption table i Auxiliary Function buttons may vary according to the model of the machine Prewash A Prewash is only worthwhile for heavily soiled laundry Not using the Prewash will save energy water detergent and time i Prewash without detergent is recommended for tulle and curtains Quick Wash This function can be used in Cottons and Synthetics programmes It decreases the washing times and also the number of rinsing steps for lightly soiled laundry When you select this function load your machine with half of the maximum laundry specified in the programme table Extra Rinse This function enables the machine
49. the upper part to close Troubleshooting e Washing machine has switched to self protection mode due to a supply problem line voltage water pressure etc gt gt gt Press and hold Start Pause Cancel button for 3 seconds to reset the machine to factory settings See Canceling the programme e Some water might have remained in the product due to the quality control processes in the production gt gt gt This is not a failure water is not harmful to the machine e Likely problems with hoses or the pump filter gt gt gt Be sure the seals of the water inlet hoses are securely fitted Attach the hose to the tap tightly e Pump filter might not be closed fully gt gt gt Make sure that the pump filter is completely closed Tap is turned off gt gt gt Open the inlet water taps fully Water inlet hose is bent gt gt gt Flatten the water inlet hose Water inlet filter is clogged Clean the water inlet filter e e e e The loading door is ajar gt gt gt Close the Loading Door e Water drain hose might be clogged or twisted gt gt gt Clean or flatten the hose e Pump filter is clogged gt gt gt Clean the pump filter Machine might be standing unbalanced gt gt gt Adjust the feet to level the machine A hard substance might have entered into the pump filter gt gt gt Clean the pump filter Transportation safety bolts are not removed gt gt gt Remove the transportation saf
50. to make another rinsing in addition to the one already made after the main wash Thus the risk for sensitive skins babies allergic skins etc to be effected by the minimal detergent remnants on the laundry can be reduced Anti Creasing This function creases the clothes lesser when they are being washed Drum movement is reduced and spinning speed is limited to prevent creasing In addition washing is done with a higher water level Rinse Hold If you are not going to unload your clothes immediately after the programme completes you may use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from getting wrinkled when there is no water in the machine Press Start Pause button after this process if you want to drain the water without spinning your laundry Programme will resume and complete after draining the water If you want to spin the laundry held in water adjust the Spin Speed and press Start Pause button The programme resumes Water is drained laundry is spun and the programme is completed e Soaking The Soaking auxiliary function ensures better removal of stains ingrained into the clothes by holding them in the detergent water prior to startup of the programme Pet hair removal This function helps to remove pet hair that remain on your garments more effectively When you select this function Prewash and Extra Rinse steps are added to the normal programme Thus washing
51. uality control processes in the production It is not harmful for the product Disposing of packaging material Packaging materials are dangerous to children Keep packaging materials in a safe place away from reach of the children Packaging materials of the product are manufactured from recyclable materials Dispose of them properly and sort in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the product 1 Unplug the product before transporting it 2 Remove water drain and water supply connections 3 Drain the remaining water in the product completely see Draining remaining water and cleaning the pump filter 4 Install transportation safety bolts in the reverse order of removal procedure see Removing the transportation locks i Never move the product without the transportation safety bolts properly fixed in place Disposing of the old product Dispose of the old product in an environmentally friendly manner Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your product For children s safety cut the power cable and break the locking mechanism of the loading door so that it will be nonfunctional before disposing of the product 12 EN n Preparation Things to be done for energy saving Following information will helo you use the product in an ecological and energy efficient
52. urther decreased giving you the opportunity for a more economical wash This feature is available for certain models having remaining time display Baby Toddler Clothing Use this programme to wash baby laundry and the laundry that belongs to allergic persons Longer heating time and an additional rinsing step provide a higher level of hygiene e Hand Wash Use this programme to wash your woolen delicate clothes that bear not machine washable tags and for which hand wash is recommended It washes laundry with a very gentle washing action to not to damage clothes Daily Quick Use this programme to wash your lightly Soiled cotton clothes in a short time e Dark Care Use this programme to wash your dark coloured laundry or the laundry that you do not want it get faded Washing is performed with little mechanic action and at low temperatures It is recommended to use liquid detergent or woolen shampoo for dark coloured laundry Mixed Fabrics Use this programme to wash your cotton and synthetic clothes together without 20 EN sorting them Special programmes For specific applications select any of the following programmes Rinse Use this programme when you want to rinse or starch separately e Spin Drain Use this programme to apply an additional spin cycle for your laundry or to drain the water in the machine Before selecting this programme select the desired spin speed and press Start
53. ws 1 Connect the green yellow or green earth wire to the terminal in the plug marked E or with the symbol f or coloured green and yellow or green 2 Connect the blue neutral wire to the terminal in the plug marked N or coloured black 3 Connect the brown live wire to the terminal in the plug marked L or coloured red With the alternative plugs a 18A fuse must be fitted either in the plug or adaptor or in the main fuse box If in doubt contact a qualified electrician Green and yellow or green Blue or Brown or black red 11 EN First use Before starting to use the product make sure that all preparations are made in accordance with the instructions in sections Important safety instructions and Installation To prepare the product for washing laundry perform first operation in Drum Cleaning programme If your machine is not featured with Drum Cleaning programme use Cottons 90 programme and select Additional Water or Extra Rinse auxiliary functions as well Before starting the programme put max 100 g of powder anti limescale into the main wash detergent compartment compartment nr Il If the anti limescale is in tablet form put only one tablet into compartment nr Il Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end i Use an anti limescale suitable for the washing machines i Some water might have remained in the product due to the q
Download Pdf Manuals
Related Search