Vogel's PFW 6831 Display wall mount - Panasonic 103 inch
Contents
1.2. Bracket B Qty 2 Step 20 Locate the four 4 M16 hex head bolts and lock washers on the back of the display and remove them place this hardware to the side as they will be used again Step 21 Align the mounting bracket holes on Mounting Bracket A with the mounting holes on the back of the display Two mounting holes will used on each side of the display Step 22 Place the lock washers between the display and the mounting brackets Step 23 Insert the M16 hex head bolts through the mounting bracket then through the lock washer and into the display Step 24 Tighten the bolt and repeat Steps 20 and 21 for the remaining three bolts Tighten all hardware A WARNING DO NOT OVERTIGHTEN THE HARDWARE CLEVIS SPRING CLIP Clevis Pin Step 25 Place Mounting Bracket B into Mounting Bracket A and install the clevis pin flat washer and clevis spring clip hardware into the lower locations on the mounting bracket Flat Washer Step 26 Repeat Step 25 for the remaining mounting bracket Page 6 Installation Instructions Sagel s eo professional PFW 6831 M8 x 70mm Lateal Shift Locking Sew M8 x 70mm Lateal Shift Locking Sew M8 x 70mm Latsal Shift Locking Sew M8 x 70mm Lateal Shift Locking Sew ane RAISE THE DISPLAYTO THE WALL PLATES FOLLOWINGTHE LIFTINGINSTRUCTIONS A PROVIDEDBY THE DISPLAYMANUFACTURERJSE AN APPROPRIATELIFTINGDEVICE ASSIST WHEN LIFTING THE DISPLAY INTO PLACE Step 27 Raise the flat panel with th
3. been drilled attach the upper mounting plate make sure the open flange side is pointing up using eight 8 5 16 x 3 lag bolts and eight 8 5 16 flat washers Tighten all upper wall plate mounting hardware and remove the hanger nail Line up the mounting holes of the side mounting bracket B with the mounting holes that are located on the side of the upper wall plate Repeat this step for the second side mounting bracket Use four 4 m5x0 8x12 Phillips heads screws 2 each side for the upper mounting points to attach the side mountin g brackets to the upper wall plate Tighten using a Phillips head screwdriver After securing the upper side mounting bracket hardware slide the lower wall plate between the lower side mounting brackets reference arrow pointing up in the event that there is no arrow make sure the open flange side is pointing up While the lower wall plate is held in place use four 4 m5x0 8x12 Phillips heads screws 2 each side for the lower mounting points to attach the side mounting brackets to the lower wall plate Tighten using a Phillips head screwdriver Repeat Steps 12 and 13 to mount the lower wall plate Tighten ALL hardware when complete Installation Instructions Page 5 vogel s ie sae PFW 683 1 A Mounting Bracket A B Mounting Bracket B M16 Bolt D Lock Washer gt Mounting Bracket A Lock Washer P a M16 Bolt Step 19 Locate Mounting Bracket A Qty 2 and Mounting
4. stud Mark this point with your pencil in from the other side swinging in from right to Step 8 Repeat the previous steps to determine the location left of all wall studs Page 4 Installation Instructions ies el s professional PFW 6831 A Upper and Lower Wall Plates B Side Mounting Brackets m5x0 8x12 Phillips Head Screws Lag Bolts and Washers wooden studs only For solid wall construction incorporate the use of wedge anchors supplied with the lag bolts m5x0 8x12 Phillips Head Screws Step 9 Step 10 Step 11 Step 12 Step 13 Step 14 Step 15 Step 16 Step 17 Step 18 A Mounting Slots Open Flange x aM vy v A Open Flagge Lag Bolts and Washers wooden studs only Once the center points on all the wood studs have been determined use a large hanger nail and partially drive it into the wood stud that will be center most of the viewing area The hanger nail will go where the pencil mark was made Locate the mounting slot closest to center on the upper wall plate A and hang the upper wall plate on the hanger nail Use a spirit level supplied to level the upper wall plate Once the upper wall plate is level mark the correspond mounting slots that line up with the studs Use a commercially available supplied 1 4 pilot drill bit to pre drill all upper wall plate mounting holes do not exceed 1 4 maximum drill bit size Once the mounting holes have
5. ARNING DERFORM LISTRUCTURAREINFORCEMENBEFORATTACHINGHEDISPLA YOTHEWALL USE THE APPROPRIATE LIFTING DEVICE WHEN LIFTING THE DISPLAY INTO PLACE Step 1 Determine and mark where the ideal viewing center of the display will be located on the wall Step 2 Measure up 24 21 615 01mm and mark this location with a pencil STUD CENTER SPACING 16 to 18 A total of four 4 studs will be used which means that you will have a total sixteen 16 mounting points Eight 8 willbe used forthe upper wallplate and eight 8 willbe used for the lower wall plate 24 A total of three 3 studs will be used which means that you willhave a total twelve 12 mounting points Three 3 willbe used for the upper willplate and three 3 willbe used for the lower wall plate 24 21 615 01 i a a i i a SF M Stud Structure Mark 1 SN Mark 2 A S QQ GF A ys A RS Stud Finder Step 6 When the lights illuminate or a buzzer sounds Step 3 Using a commercially available stud finder mark that spot on the wall using a pencil place it against the wall and swing it from left to right Step 7 Now that the edges of the wall stud while engaging the button have been located use your tape measure Step 4 When the lights illuminate or a buzzer sounds mark that and determine the center point between spot on the wall using a pencil the two marks This will be center of the Step 5 Repeat Step 2 but this time swing the stud finder
6. PFW 6831 Display Wall Mount For use with Panasonic TH 103PF10UK Series 103 Plasma Displays INSTALLATION INSTRUCTIONS 9531 0028 Z00 01 lt Gdgel s gt professional PFW 6831 Table of Contents Installation Instructions Technical Specifications Warning Statements 2 Parts List 3 Recommended Installation Tools 3 Features 4 4 8 Warning Statements INSTALLTHE DISPLAYACCORDINGTO THE INSTRUCTIONPROVIDEDBY THE DISPLAYMANUFACTURER A PERFORM ALL STRUCTURAIREINFORCEMENTBEFORE ATTACHINGTHE DISPLAY TO THE WALL USE THE APPROPRIATE LIFTING DEVICE WHEN LIFTING THE DISPLAY INTO PLACE W PRIOR TO THE INSTALLATIONF THIS PRODUCT THE INSTALLATIORNSTRUCTIONSHOULD BE READ AND STOP COMPLETELWNDERSTOODLHEINSTALLATIONSTRUCTIONHUSTBEREADIO PREVENPERSONAIINJURYND PROPERTDAMAGEKEEPIHESHNSTALLATIOINSTRUCTIONIN AN EASIL ACCESSIBUBOCATIONFOR FUTURE REFERENCE _ VOGEL S DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY VOGEL S PRODUCT FORPURPOSEWTHERTHANTHOSH ORW HICHTWASDESIGNEIDRDAMAGKAUSEIB YUNAUTHORIZEDTTACH MENTSOR MODIFICATIONSANDIS NOTRESPONSIBLEOR AN YODAMAGESCLAIMSDEMANDSSUITS ACTIONDR CAUSEXF ACTIONOF WHATEVEKRINDRESULTINGROM ARISIN UTOF ORIN ANYMANNERELATINGO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE WALLSTRUCTURMUST BE CAPABLEOF SUPPORTING 907 KG IF NOT THE WALLSTRUCTURMUST BE REINFORCEDPROPERINSTALLATIORROCEDURBY A QUALIFIEDSERVICHECHNICIAMS OUTLINEDOIN THE INSTALLATIOBNSTRUCTIONMUSTBE ADHERED O FAIL
7. URHO DO SO COULDRESULTIN SERIOU PERSONAL INJURY OR EVEN DEATH SAFETWEASUREMUSTBEPRACTICEIATALLITMEDURINGPHEINSTALLATIOOF THISPRODUCTUSEPROPER W SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY THIS MOUNT IS NOT RECOMMENDED FOR USE WITH STEEL STUD WALL STRUCTURES THAT ARE LESS THAN 10 GAUGE IN THICKNESS ON THE PROPOSED INSTALLATION WALL Indicates that the power plug is to be disconnected from the power outlet Safety precautions must be taken at all times Warning and Caution statements Itisrecommended that a maximum of 5 8 thick plaster board be used along with 5 16 lag bolts and flat washers when mougtio wooden studs Do not install next to any high heat sources Failure to do so may result in damage to the flat panel display and could inc thse risk of fire In the interest of safety it is recommended that two to three people with the aid of an appropriate assisted lifting devpeeform this installation Injury and or damage can result from dropping or mishandling the flat panel display Page 2 Installation Instructions vogel s gers PFW 6831 Parts List This wall mount is shipped with all proper installation hardware and components Make sure that none of these parts A Note are missing and or damaged before beginning installation Wall Mounting Plates Qty 2 Mounting Brackets Qty 2 Side Straps Qty 2 m5x 8x12 Phillips Head Screws Qty 8 5 16
8. e mounting brackets attached and hang the top and bottom hooks over the mounting rods that are on the upper and lower wall plates Step 28 Once the display is attached to the wall insert four 4 M8 x 70mm lateral shift locking screws The mounting points for these screws are located on the top and at the bottom of the mounting brackets Step 29 These screws once tightened down will prevent the display from sliding side to side Make any lateral adjustments at this time and then tighten the lateral shift locking screws down 2 3 and 4 the 1 setting will leave the display in a full vertical position There are four hole settings at the bottom Once the display is mounted securely to the wall the forward tilt must be determined There are four tilt setting 1 A mre of each mounting bracket Step 30 Determine the forward tilt setting Step 31 Insert the clevis pin through the mounting hole Step 32 Once the clevis pin is completely through the mounting hole place the clevis pin flat washer onto the clevis pin and insert the cotter pin into the clevis pin Repeat this step for the remaining side Installation Instructions Page 7 Wdgel s eo professional PEW 6831 Technical Specification All measurements are in inches mm 70 33 1786 3 16 00 16 00 i 16 00 16 00 406 4 406 4 406 4 406 4 A Sm N N D E E C a io oe e eee oe Pe x N Installation Instructions 48 4 1229 8 Page 8
9. x 3 Lag Bolts Qty 16 OO OOOO 5 16 Flat Washers QOOOO Qty 16 5 16 Tri Lobe Anchor Qty 16 Pencil Tape Measure Spirit Level Supplied 3 8 Concrete Drill Bit For use with 3 8 concrete 1 2 Socket and Wrench 2 Phillips Screwdriver Stud Finder Ladder wedge anchors Installation Instructions Page 3 professional x2 5 vogels eg PFW 6831 Installation Instructions Ease of Installation Vogel s has designed this mount with installer ease of installation in mind Tilt Flat Display Orientation With the PFW 683 you can mount your display flat to the wall or if you choose there is a variable tilt feature on the PFW 6831 This will allow you to tilt your display forward for a more optimized viewing angle Side to Side Lateral Shift Centering the display has never been easier The PFW 6831 features 3 built in side to side lateral shift This feature will allow you to slide the entire display left or right to adjust the final position of the display THE WALLSTRUCTUREMUST BE CAPABLEOF SUPPORTING 907 KG IF NOT THE WALL A WARNING STRUCTURMUST BE REINFORCEDPROPER INSTALLATIORROCEDURBBY A QUALIFIED SERVICETECHNICIANAS OUTLINEDIN THE INSTALLATIONNSTRUCTIONSMUST BE ADHERED TO FAILURETO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH USE SUITABLE CONCRETE ANCHORS FOR 3000PSI POURED CONCRETE WALLS FOLLOWTHEINSTRUCTIONSROVIDEIB YTHEMANUFACTURBRHENLIFTINCTHEDISPLA Y A W
Download Pdf Manuals
Related Search