Chief LPAUS
Contents
1. engagement without contacting bottom of display mounting holes Select screw length See Figure 5 Using your hand insert SHORTEST length screw of selected diameter TA TD TG or TI through universal washer TN uprights B selected spacer TL or TM into display mounting hole Do NOT thread screw into hole at this time Universal washers TN are not needed if using M8 button head cap screws TI TJ or TK Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter If screw length is inadequate select longer screw Select shortest screw which will protrude the required distance Place uprights B on display ensuring See Figure 5 Center of uprights B are as close to the center of the back of display as possible after being installed Center of bracket is indicated by the diamond shaped hole Use selected screws and spacers to install two interface uprights B to back of display See Figure 5 Q YY TA TH Be AE 5 LPAU Installation Instructions 9 Move latches on interface uprights to the closed position to secure display to head assembly See Figure 8 WARNING Display may be very heavy Ensure display may be safely lifted and maneuvered as required to install on cart Failure to take adequate precautions can result in 7 serious personal injury or damage to equipment2. 7 Position latches on interface uprights so that they are in the open position See Figure 6 8 Hang interface uprights on interface head assembly E See Figure 6 open position Figure 8 10 Snap four upright covers A onto uprights See Figure 9 NOTE Tabs on inside of covers A will snap directly into holes on uprights to ensure a secure connection Figure 6 IMPORTANT In order to ensure an even mount install uprights to be centered over column assembly Do NOT install both uprights to the same side of column assembly See Figure 7 NI Figure 9 11 Optional Use padlocks not provided to secure uprights to head assembly See Figure 9 Figure 7 Installation Instructions LPAU Cable Management NOTE The following cable management options may vary based on type of display being mounted and user preference 1 Use two 1 4 20 x 1 2 Phillips pan machine screws Q to attach two cable hooks K to bottom of column assembly F See Figure 10 Figure 10 2 Place FCA clip U into groove on back of Fusion mount with clip handle in a vertical position See Figure 11 3 Rotate FCA clip U 90 in either direction until clip handle is in a horizontal position See Figure 11 4 Repeat Steps 1 2 for all clips t
3. INSTALLATION INSTRUCTIONS Height Adjustable Video Cart S CHIEF LPAU Our Mounts Your LPAU Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is t
4. e head assembly E to column assembly F See Figure 3 Figure 3 9 Use remaining 5 16 18 x 3 4 button head cap screw N to secure column upper cover C to interface head assembly E See Figure 4 10 Snap column inner cover D onto column assembly F See Figure 4 Figure 4 Installation Instructions LPAU Display Installation WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the LPAU up to and including the display does not exceed 200 Ibs 90 7 kg 1 Lay display face down on protective surface CAUTION Using screws of improper diameter may damage your display Proper screws will easily thread into display mounting holes 2 Select screw diameter by examining hardware 4mm 5mm 6mm or 8mm and comparing with mounting holes on display See Figure 5 3 Select spacers See Figure 5 f mounting holes are not recessed and both uprights B can lay flat against display then no spacers are required f mounting holes are recessed or if protrusions prevent uprights B from laying flat then spacers TL or TM must be used 4 NOTE CAUTION Using screws of improper length may damage your display Proper screws will have adequate thread
5. he installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the LPAU up to and including the display does not exceed 200 Ibs 90 7 kg WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors WARNING RISK OF INJURY TO PERSONS Do not place video equipment such as televisions or computer monitors on cart legs SAVE THESE INSTRUCTIONS Installation Instructions LPAU DIMENSIONS CEBLECORD W wAP H0 0 LS 1145 TIT AD USTHENT 141 200 M H EI 31 50 EO 11
6. i d I 15 15 e a uta i do H i i f H B wana b d i 11193 m j WAL HE RTI il CENTER OE DISPLAY LPAU Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aper
7. o be installed clip handle Figure 11 5 Route cables along FCA clips to be used for cable management See Figure 12 6 Use cable ties V to secure cables to FCA clips See Figure 12 Figure 12 7 Route cables from display through front channel of column assembly See Figure 13 cable example front channel Figure 13 LPAU Installation Instructions Route cables down column channel tucking them behind height adjustment carriage and underneath bracket holding height adjustment shaft See Figure 14 Wrap cables around cable hooks as desired See Figure 14 Snap back cover G onto back of column assembly making sure cables fit through opening at bottom of cover See Figure 14 rear view o N 8 under bracket NI cable opening 10 Figure 14 Adjustments Height Adjustment LE 2 Remove cable cover G to expose height adjustment knob Turn height adjustment knob clockwise to raise display See Figure 15 Turn height adjustment knob counterclockwise to lower display See Figure 15 WARNING Do not attempt to raise or l
8. om 01 13 USA International Europe Asia Pacific p TI U gt O 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH n O 0 SFCONSUMERS
9. ower the adjustment carriage beyond its upper or lower limit High and low points are shown in Figures 15 and 16 NOTE A 1 2 socket wrench may also be used to adjust height 4 by turning bolt just above height adjustment knob Reinstall cable cover G to column assembly height adjustment knob x high Figure 15 low point Figure 16 Installation Instructions LPAU Pitch Adjustment 5 Turn pitch adjustment knob clockwise to tilt display forward See Figure 17 6 Turn pitch adjustment knob counterclockwise to tilt display back See Figure 17 Roll Adjustment 7 Turn roll adjustment knob clockwise to adjust roll to the left See Figure 17 8 Turn roll adjustment knob counterclockwise to adjust roll to the right See Figure 17 9 pitch adjustment knob roll adjustment knob Figure 17 11 LPAU Installation Instructions G CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002209 Rev03 2013 Milestone AV Technologies a Duchossois Group Company www chiefmfg c
10. te Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a mao A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option J A CW vw CY Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale O O O O Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions LPAU TOOLS REQUIRED FOR INSTALLATION M5 included 3 16 included PARTS lt N xm A hardware bag c a lt 2 P e e A 4 column Sn cover TB 6 TC 6 upright TON e mu c Tee M4x25mm interface upright FS e e e column inner cover TD 6 TE 6 TF 6 G 0 Y M5xi6mm M5x20mm M5x25mm back cover 1 ge e 2 interface head assembly solum assembly TG 8 TH 6 M6x16mm M6x25mm Jm a right cart leg ie 62 e T dd cable hook TI 6 H 1 M8x20mm Maxdomm i oe left cart leg p ke o La TM TN 8 TP ui left transition co
11. ver right fianetion Laan Ma ie Einer e vA e0 gt cable VW P i P N 5 5 16 18x 3 3 4 Qi 3 16 un LPAU Installation Instructions Assembly And Installation CAUTION Attachment holes may be damaged if a power drill is used to insert button head cap screws Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the head head drill bit and power drill to complete the attachment Cart Assembly 1 Carefully set column assembly F on its left side See Figure 1 2 Place right transition cover M on right cart leg J lining up the holes on the cover with the holes on the leg and column assembly base See Figure 1 3 Use two 5 16 18 x 3 3 4 button head cap screws P to secure leg J and cover M to column assembly F See Figure 1 rear view x x2 c Figure 1 4 Turn column assembly F onto its right side See Figure 2 Figure 2 5 Place left transition cover L on left cart leg lining up the holes on the cover with the holes on the leg and column assembly base See Figure 2 Use two 5 16 18 x 3 3 4 button head cap screws P to secure leg H and cover L to column assembly F See Figure 2 7 Slide interface head assembly E into column assembly F See Figure 3 8 Use four 5 16 18 x 3 4 button head cap screws N to secure interfac
Download Pdf Manuals
Related Search