Home

Zoom ADSL X7N ADSL2+ Wi-Fi Ethernet LAN Black

1. the computer is no longer protected by the X7N s NAT firewall Caution should be used when setting up a computer with a DMZ A game station does not have the same secutity issues as your computer so setting up a DMZ works normally well with your game station You may want to create a DMZ if a computer in your network is acting as a web server or hosting Internet games You need to manually assign an IP address to the DMZ Please refer to Configuring Fixed DHCP Mapping for instructions on how to manually assign an IP address to the DMZ DMZ Host IP Address Enter the IP address of the computer or gaming station designated as a DMZ Note You need to give your LAN PC clients a fixed static IP address for DMZ to work properly To do this go to Configuring Fixed DHCP Mapping on page 54 Click Save Apply Chapter 8 Advanced X7N Setup Options X7N User Manual Port Triggering Port triggering allows a host machine to dynamically forward a specific port back to itself and is a way to automate port forwarding When traffic is seen on an outgoing port any traffic received on the corresponding incoming port will be forwarded to your computer or gaming station To set up port triggering follow the instructions below 1 Click Advanced Setup gt NAT gt Port Triggering 2 Click Add to add a new Port Triggering rule 3 Check the drop down list next to Server Name check that this is called server name If your game or application
2. Virtual Path Identifier ranges from 0 256 Your DSL provider supplies the VPI when you sign up for ADSL service Virtual Circuit Identifier ranges from 0 65536 Your DSL provider supplies the VCI when you sign up for ADSL service Your DSL provider supplies this PPP User Name when you sign up for ADSL service Your DSL provider supplies this PPP password when you sign up for ADSL service These settings allow you to give priority to data that is sent over the network Important You must make arrangements with your DSL provider 51 to use anything except UBR Unspecified Bit Rate in the Traffic Class setting Your service provider will also supply you with the Cell Burst and Tolerance Rates NAT Network Address Translation By default this setting is Enabled NAT keeps a table of individual private IP addresses in your network and refers to the table when incoming requests are made If no matches are found the incoming data cannot come into your network An Enabled setting keeps your IP addresses hidden from outside users MTU Maximum Transmission Unit Largest physical packet size measured in bytes that the modem can send Any messages larger than the MTU have to be fragmented before being sent After you enter your values click Save Apply Automatic Configuration You can use Automatic Configuration if you want to automatically set your Protocol Encapsulation VPI and VCI settings Clic
3. Macintosh TCP IP Settings acc sctesndvaiveleucnssabtandediionn 90 Windows TCP IP SettingS ooooccccnnnoccccnnnoccccnnncnnns 92 Appendix E Configuring Your Web Browser 96 Appendix F Wireless Channels by Country 102 Appendix G Getting Help ooooccconnncccninaniccnnnnanaccnnnnnas 103 Appendix H Regulatory Information ommmommo 104 Europe EU Declaration of ConforMity cccomomanassascnaannos 109 Overview This User Manual provides instructions for setting up your X7N connecting the X7N to wited and wireless computers or other devices on a network and securing your network There are also instructions for setting up the X7N for gaming For most customers Chapter 1 covers what you need to get connected to the Internet Chapter 2 applies if you want to set up a network Chapters 3 and 4 help you set up and secure your X7N wireless network Chapter 5 focuses on wireless options primarily for advanced users and Chapter 6 provides what you need for online gaming Chapters 7 9 provide advanced information that is primarily for System Administrators These chapters explain how to use advanced features of the X7N such as adding extra security with firewall filtering backing up and restoring the X7N configuration updating the X7N firmware creating a fixed IP address monitoring status and management and diagnostic features of your X7N Installation Instructions This chapter covers th
4. You can automatically configure WPS security using the router s built in WPS configuration program on each client device that is part of your wireless network The X7N supports Push Button WPS configuration This button can be either a physical button on the unit or a software button in its application If your devices only support using a PIN code then you must configure security manually Refer to Setting Up Security Manually on page 19 Note WPS configures one client device at a time Please repeat the configuration method for each client on your wireless network that supports WPS security 1 Press the WPS button on your X7N and hold it in for two 2 seconds After you release the button the WPS light on the front of the X7N should start to blink Important The Registrar the device configuring the WLAN goes into the WPS mode and the Enrollee the device joining the WLAN then looks for it You should always start the Registrar first The X7N is configured as a Registrar so you should put it into WPS mode first 2 Click or press the WPS button on the client device This button may be a physical button on the unit or a software button in its application 3 Refer to your client device s documentation for further instructions if necessary For each device that you used WPS to enable security and connect to the X7N test your Internet connection by opening your Web 23 browser for instance Internet Explorer Firefox or
5. you may need to know the IP address assigned to you by your Internet service provider For advanced users with special configuration needs the status information is useful for overall system maintenance Monitoring ADSL Status If you want to check the status of your ADSL connection click on the Status link on the left pane in the Zoom Configuration Manager If you forgot how to log in to the Zoom Configuration Manager see page 14 Chapter 7 Status Monitoring X7N User Manual The Status page provides information about your ADSL connection For example you can verify whether your ADSL connection is active or not You can also monitor related ADSL parameters for example how fast the X7N is transferring data Downstream Speed and Upstream Speed your WAN settings your LAN settings and so forth Note The Status page does not provide a way to change any of these settines see Chapter 8 Advanced X7N Setup Options if you need to make changes to these settings 45 Advanced X7N Setup Options Advanced Setup is primarily for technically advanced users For most people the options that are set by default when the X7N is installed are sufficient However those who want or need to change the X7N settings can do so using the Advanced Setup page in the Zoom Configuration Manager This chapter explains the advanced options and features of the X7N modem and how to apply them to your network The information in th
6. 207 South Street Boston MA 02111 USA 617 423 1072 www zoomtel com Brand Marca Zoom ADSL Modem Router w Wireless N Type Tipo Series 1093 Model 5790XY where X A B C D E F or nothing and Y G H J K L M or nothing The manufacturer declares under sole responsibility that this equipment is compliant to Directive 1999 5 EC via the following This product is CE marked El fabricante declara bajo su exclusiva responsabilidad que este equipo satisface la Directiva 1999 5 EC por medio de lo siguiente Este producto tiene marca CE 73 23 EEC LVD EN60950 1 2006 A11 2009 A1 2010 IEC60950 1 2005 89 336 EEC EMC EMF EN301 489 1 V1 8 1 2008 04 EN301 489 17 V2 1 1 2009 05 EN55022 2006 Class B 1999 5 EC EN300 328 v1 7 1 2006 10 CE Director Hardware Engineering Paul Prohodski Director Inaenier a de apovo 8 November 2011 1084 TF Boston MA USA Regulatory Notices for X7n Router with Wireless N Regulatory Notices also apply to ADSL Splitter Model TD 1301 U S FCC Part 68 Statement This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA The unit bears a label on the back which contains among other information a product identifier in the format US AAAEQRFTXXXX If requested this number must be provided to the telephone company This equipment uses the following standard jack types for network connection RJ11C This equipment contains an F
7. Changing Your WAN SettidgQS cooonnccccnnnncccccccnonccccccnnns 50 Changing Your LAN Settings cooooccccnnnoncccnnnncnccccnnnn 52 Configuring Fixed DHCP Mapping occcccccocccccccccnncnccnnnn 54 Creating a Virtual Server a DMZ or Using Port o E EA A aa vosevaecs 55 Creating a Virtual Server oooonnoccccnnnnccccncnoccnnnnnonannnnnnnnns 55 DMZ taaan 56 a occa decay warcunasta dee oe can cece neonate eee canes 57 Using IP PINCUS pecto cdi 57 Using MAC Filtering s scisci ciasiisimeciancataa tencia 58 Setting Up Time RestrictiONS oooonnnccccnnncnccccnnccccccnnnnns 59 Setting Up a Static Routing Table 60 Adding a DNS Server Name cooooccccocooccccccconncccccnannnnnnnnns 61 Using the ADSL SettingS ccooococcnnnnocccnnnoncccncnnnanccons 61 Enabling or Disabling UPAP ociosos ninas reat 62 Management and Diagnostics ccocccccccnnnnnnnnanccnnnnonnnnnnas 63 Backing Up Your Configuration oooocccncccccnnonoccccnnnnanccn 66 Resetting Default SettingS coomccccnnincccnnnnccccnnnnccccnn 67 Remote Access to Your Modem Configuration Settings68 Changing User Names and Passwotds 2 0 000 69 OG ie eee Sih et te A E 70 Dago cio is 70 Appendix A Troubleshooting TipPS oomooccccccconnnnnnnnnannnn 71 Appendix B ADSL Internet Settings Tables 82 Appendix C Top and Back Panels 0ooooocccccccccnnnncccannnnns 88 Appendix D TCP IP Network Settings mmmmooooo 90
8. Chapter 3 you will need to set up wireless security and enter the password Tip If you need help refer to the documentation that came with your wireless device There are several site scan issues you should be aware of gt More than one wireless network may appear in the list These are other wireless networks that are within range of your network Your neighbors for instance may be within range of your network Each wireless network has a channel associated with it We recommend there be at least a five channel difference between your network and those of yout neighbors Having less than a five channel difference may result in interference with your connection By default the X7N uses channel 10 If you need to change this channel you must do so using the Wireless Setup page of the Zoom Configuration Manager For instructions on how to log in to the Zoom Configuration Manager see page 14 After logging in select Wireless from the left side menu On the Wireless page you can select a new channel from the drop down menu gt If you want to secure your wireless network so it won t be accessible by others you should specify security settings To learn how see Setting Wireless Security on page 19 By default the wireless connections provided by the X7N do not have any security applied 2 Test your wireless connections From each computer or device that you set up open your Web browser for instance Internet Explorer Fi
9. Chrome and try to connect to a familiar Web address If you connect successfully you are ready to browse the Web If it fails to connect refer to Appendix A Troubleshooting Tips on page 70 You are now ready to start using your X7N If you want additional information on how to use your X7N you may choose to continue with gt Chapter 6 to learn about using the X7N with online gaming gt Chapter 7 to learn about monitoring your ADSL Status Most users will not need to use status monitoring gt Chapter 8 to learn about the advanced features of the X7N Most users will not need to change advanced features Chapter 3 Setting Wireless Security X7N User Manual Connecting Devices Wirelessly to the X7N This chapter assumes that your X7N has its wireless security settings set up the way you like them either with the factory defaults of no security or with a particular type of security as discussed in Chapter 3 This chapter provides tips for connecting devices computers phones non computer wireless device like an iPhone or other cellular phone iPod Touch etc wirelessly to the X7N If you are familiar with this already or if you prefer to use the instructions associated with each device you don t need to read this chapter You do need to make sure that each device connecting to the X7N is set up for wireless security that is compatible with the X7N s wireless security settings Note that for ea
10. MUX Germany 1 32 PPPoE LLC edi 0 35 PPPoE LLC Iceland Islandssimi 0 35 PPPoA VC MUX Iceland Siminn 8 48 PPPoA VC MUX Israel 8 35 PPPoA VC MUX Italy 8 35 PPPoA VC MUX Appendix B ADSL Internet Settings Tables 85 Jamaica 1 35 PPPoA VC MUX Jamaica 2 35 PPPoA VC MUX Jamaica 3 35 1483 Bridged IP LLC SNAP Jamaica 4 35 1483 Bridged IP LLC SNAP Kazakhstan 33 PPPoA VC MUX Mexico 35 PPPoE LLC Netherlands BBNED 35 PPPoA VC MUX Netherlands MX Stream 48 PPPoA VC MUX New Zealand Slingshot 100 PPPoA VC MUX Portugal 35 PPPoE LLC Puerto Rico Coqui net 35 PPPoA LLC Saudi Arabia 1 33 PPPoE LLC Saudi Arabia 2 35 PPPoE LLC Saudi Arabia 3 33 1483 Bridged IP LLC Saudi Arabia 4 33 1483 Routed IP LLC Saudi Arabia 5 35 1483 Bridged IP LLC Saudi Arabia 6 35 1483 Routed IP LLC Spain Albura Tiscali 32 PPPoA VC MUX Spain Colt Telecom Ola Internet 35 PPPoA VC MUX Spain EresMas Retevision 35 PPPoA VC MUX Spain Telefonica 1 32 PPPoE LLC Spain Telefonica 2 Terra 32 1483 Routed IP LLC Spain Wanadoo 1 35 PPPoA VC MUX Spain Wanadoo 2 32 PPPoE LLC Spain Wanadoo 3 32 1483 Routed IP LLC Appendix B ADSL Internet Settings Tables X7N User Manual Sweden Telenordia 35 PPPoE Sweden Telia 35 1483 Routed IP LLC Switzerland 35 PPPoE LLC
11. Start button and then depending on your computer either click Control Panel or click Settings and then Control Panel In the Control Panel double click the Internet Options icon If this icon does not appear double click the Network and Internet Options icon and then double click the Internet Options icon 2 Once open select Tools gt Internet Options and then click on the Connections tab 3 Select Setup to setup an Internet connection which will open the New Connection Wizard screen 4 Click Next 5 Select the type of connection desired Select Connect to the Internet to access the modem s HTTP Server Click Next 6 Select Set up my connection manually Click Next 7 Select Connect using a broadband connection that is always on Click Next Appendix E Configuring Your Web Browser X7N User Manual 8 Select Finish Configuring Internet Explorer 5 0 or 6 0 The following instructions are for Internet Explorer Version 5 0 and 6 0 If you are not sure what version you have open Internet Explorer and from the Help menu choose About Internet Explorer The version number is directly below the Microsoft Internet Explorer logo You can ignore all the numbers after the period following the first digit 1 On the desktop right click the Internet Explorer icon and select Properties Tip If you cannot access Internet Explorer in this way open your computer s Control Panel click the Start button and then depending on y
12. X7N will need to verify the TCP IP settings Depending on your operating system follow the steps in the appropriate section to ensure your TCP IP settings are correct e If you are using Macintosh see Macintosh TCP IP Settings on page 90 e If you are using Windows see Windows TCP IP Settings on page 92 Macintosh TCP IP Settings How you configure your Macintosh computer s network settings differs depending on your Mac OS For OS X follow the instructions below Otherwise go to page 91 Mac OS X 10 7 Lion 10 6 Snow Leopard and 10 5 Leopard 1 From the Dock or Apple menu select System Preferences and then Network 2 Select your connection method normally Ethernet for a wired connection Appendix D TCP IP Network Settings X7N User Manual 3 On the right pane select Using DHCP from the Configure IPv4 for Mac OS X v10 7 and v10 6 and Configure for Mac OS X v10 5 drop down menu All of the text fields should be left blank 4 Click Apply Mac OS X 10 4 and 10 3 1 From the Dock or Apple menu select System Preferences and then Network 2 Select your connection method normally Built in Ethernet for a wited connection 3 Make sure the TCP IP tab is selected and then select Using DHCP from the Configure IPv4 drop down menu All of the text fields should be left blank 4 Click Apply Now Mac OS 7 6 1 9 2 2 1 From the Apple menu choose Control Panels and then TCP IP to display the TCP IP
13. is listed go ahead and select it 4 Click Save Apply If your game or application is not listed enter a Custom Name for your port triggering rule and go to step 5 5 Enter the Start and End Trigger Ports in the text fields Your games documentation should supply you with this information 6 Select the Protocol for the Trigger Protocol from the drop down menu 7 Enter the Start and End Open Ports in the text fields 8 Select the Open Protocol from the drop down menu 9 Repeat steps 5 8 for each range of ports you want to trigger open ports with When you are finished go to step 10 10 Click Save Apply Note To delete a previously created Trigger Port click the checkbox of the Trigger Port in the Trigger Port list and click Delete Then click Apply to save your settings Using IP Filters Use the IP Filter Configuration page to set up IP filters to block outgoing or allow incoming traffic into your computer from the Internet To open this page click Advanced Setup gt Security Then click on IP Filtering Select Outgoing or Incoming depending on which type of filter you want to set up 57 Outgoing IP Filtering Setup By default all outgoing IP traffic from LAN is allowed but some IP traffic can be blocked by setting up filters Choose Add or Remove to configure outgoing IP filters Once you have set up the IP filters you want click the Save Apply button Incoming IP Filtering Setup By default all incoming IP
14. make changes to your modem s configuration from your remote PC We recommend leaving Remote access off to prevent unauthorized access to your router If you wish to leave it on you should change the default passwords See Changing User Names and Passwords below Changing User Names and Passwords Use the Passwords page to manage the user names and passwords that can access the Zoom Configuration Manager To open this page click Management gt Access Control gt Passwords When you installed the X7N and tried to open the Zoom Configuration Manager you were prompted for a User Name and Password in order to gain access The default User Name and Password were supplied to you in the section Logging into the Configuration Manager If you want you can change the default password Changing the password is not required but as a good security measure we recommend it To change the default password Access to your DSL modem is controlled through three user accounts admin support and user 1 Select the User Name for which you want to change the Password from the drop down menu of the Passwords page of the Configuration Manager Admin allows complete access to all functionality both locally and remotely Support allows remote access to all functionality except SSH User allows the 69 user to access the DSL Router view configuration settings and statistics as well as update the router s software 2 Enter the c
15. site If you cannot connect to the Web please refer to Appendix A Troubleshooting Tips If you want to connect other computers or other devices to the X7N continue with Chapter 2 Setting Up a Network on page 17 If you do not wish to add additional devices to your X7N you are ready to start using your X7N If you want additional information on how to use your X7N you may choose to continue with gt Chapter 6 to learn about using the X7N with online gaming gt Chapter 7 to learn about monitoring your ADSL Status Most users will not need to use status monitoring gt Chapter 8 to learn about the advanced features of the X7N Most users will not need to change advanced features Chapter 1 Installation Instructions X7N User Manual Logging into the Configuration Manager The Configuration Manager is built into the X7N and accessed through a web browser Various chapters in this manual ask you to use the configuration manager To Log into the Zoom Configuration Manager 1 Open your Web browser and in its address bar type http 192 168 1 1 and then press the Enter key on your keyboard In the Enter Network Password dialog box type the following user name and password in lowercase then click OK The X7N User Name and Password you enter here are not the same as the User Name and Password that your Internet service provider may have given you User Name admin Password zoomadsl If you are n
16. that you used to get into the Zoom Configuration Manager Note Remember that these terms are case sensitive Pay careful attention to whether you re using a capital or small letter a zero or the letter O and so on Clearly write down and store the User Name and Password on the bottom of the X7N case for instance and in a ModemSettings file C Click Save Apply e If Automatic Configuration does not work or in the unlikely event you are using a Static IP you can configure your settings manually by following these instructions a On the Basic Setup page enter your Protocol Encapsulation VPI and VCI settings in the appropriate boxes Your service provider should supply these values If you do not know these settings refer to the tables starting on page 70 b Depending on the Protocol setting you selected the bottom half of the page will change so that you can enter additional information e Ifyou selected PPPoA or PPPoE enter your ADSL User Name and Password in the appropriate boxes Your Internet service provider should have given this information to you Your User Name is typically your Chapter 1 Installation Instructions X7N User Manual email address or the characters preceding the sign in your email address This is NOT the same User Name and Password that you used earlier to open the Zoom Configuration Manager Note Remember that these terms are case sensitive Pay careful attention to whether you re
17. traffic from the WAN is blocked when the firewall is enabled However some IP traffic can be accepted by setting up filters To filter Internet traffic you must define one or more rules that is criteria you want the information to meet before it can proceed As information comes in from the Internet the X7N examines it and if it meets the rule the information moves forward to its destination on your computer or network If it does not it is discarded The rule can be based on many characteristics including the network or Internet protocol it carries the source IP address the port that the traffic is coming in on and so forth Choose Add or Remove to configure incoming IP filters Once you have set up the IP filters you want click the Save Apply button Using MAC Filtering Use the MAC Filter Configuration page to block a device from accessing the Internet To open this page click Advanced Setup gt Security Then click on MAC Filtering Select ADD to add the MAC address of the device you wish to prevent from accessing the Internet If you do not know the MAC address Click on STATUS gt DHCP for a list of devices and their MAC address that are connected to your X7N Chapter 8 Advanced X7N Setup Options X7N User Manual Setting Up Time Restrictions Do need time restrictions Time restrictions can be used to prevent a user from accessing the Internet during certain hours For example you can use Time Restri
18. using a capital or small letter a zero ot the letter O and so on Clearly write down and store the User Name and Password on the bottom of the X7N case for instance and in a ModemSettings file If you selected 1483 Bridged or 1483 Routed you have the option of using either dynamic or static IP addressing Depending on your situation select the appropriate option button 1 MOST USERS Ensure that Obtain an IP address Automatically is selected if you are using Dynamic Host Configuration Protocol also known as DHCP or dynamic IP addressing This option is selected by default because most Internet service providers use DHCP ii Select Use the following IP Address only if you are using a static IP address You should know if you are using static IP addressing There is typically an extra charge for a static IP address and you usually have to make special arrangements with your Internet service provider to get one ii Then enter the IP Address Subnet Mask Default Gateway and DNS that you plan to use C NAT Network Address Translation is Enabled by default This feature lets multiple users access the Internet sharing a single IP address Enabled is typically the right setting Select Disable in the unlikely event that you want to assign different public IP addresses to each network user d Click Save Apply Now check that your installation worked by opening a Web browser and connecting to your favorite web
19. your home has specially wired alarm equipment connected to the telephone line ensure the installation of this equipment does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer WHEN PROGRAMMING EMERGENCY NUMBERS AND OR MAKING TEST CALLS TO EMERGENCY NUMBERS Appendix H Regulatory Information 1 Remain on the line and briefly explain to the dispatcher the reason for the call 2 Perform such activities in the off peak hours such as early morning or late evenings U S FCC Part 15 Emissions Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation betw
20. 35 1483 Bridged IP LLC SBC 3 8 35 1483 Bridged IP LLC Socket 1 8 35 1483 Bridged IP LLC Socket 2 0 35 1483 Bridged IP LLC Socket 3 0 35 PPPoE LLC Sonic 0 35 1483 Bridged IP LLC SouthWestern Bell 0 35 1483 Bridged IP LLC Appendix B ADSL Internet Settings Tables 83 Sprint 1 35 PPPoA LLC Sprint 2 35 PPPoE LLC SureWest i Communications 1 33 1483 Bridged LLC Snap SureWest Communications 2 32 PPPoE LLC SureWest Communications 3 32 PPPoA LLC Toast Net 35 PPPoE LLC Uniserve 33 1483 Bridged IP LLC US West 32 PPPoA VC MUX Verizon 1 35 PPPoE LLC Verizon 2 35 1483 Bridged IP LLC Appendix B ADSL Internet Settings Tables XZN User Manual Table B Countries Other Than The USA ISP VPI VCI Encapsulation Australia Telstra 8 35 PPPoA LLC Argentina Telecom 0 33 PPPoE LLC ceo 8 35 PPPoE LLC Argentina 1 33 PPPoA VC MUX Belgium ADSL Office 8 35 1483 Routed IP LLC Belgium Turboline 8 35 PPPoA LLC Bolivia 0 34 1483 Routed IP LLC Brazil Brasil Telcom 0 35 PPPoE LLC Brazil Telefonica 8 35 PPPoE LLC Brazil Telmar 0 33 PPPoE LLC Brazil South Region 1 32 PPPoE LLC Colombia EMCALI 0 33 PPPoA VC MUX Columbia ETB 0 33 PPPoE LLC Costa Rica ICE 1 50 1483 Routed IP LLC a b a 0 35 PPPoA VC MUX France 1 8 35 PPPoE LLC France 2 8 67 PPPoE LLC France 3 8 35 PPPoA VC
21. A wireless guest network can be set up so you can give visitors access to the Internet without giving them access to other computers on your network Chapter 5 Wireless Options X7N User Manual To setup a Wireless Guest Network 1 Click on Wireless from the left side menu to take you to the Wireless Basic Setup page 2 Click the Enabled check box to enable the Guest wireless network 3 Enter a name for your guest network in the SSID field TIP You may want to include the word guest in the name so users know it is a guest network For example MyCompany Guest The table explains the following settings for your Wireless Guest Network This setting Hidden Isolate Clients Disable WMM Advertise Enable WMF Max Clients BSSID Lets you specify Click in the check box if you do not want to broadcast the SSID of your network Enabling client isolation will prevent wireless clients on the same network from communicating with each other Typically this feature would be used on a guest network WMM is used to give wireless data different levels of priority You can disable WMM to give all users equal priority Allows you to enable Wireless Multicast Forwarding WMF Most users should leave this disabled Up to 16 wireless clients are allowed on each network Reports the wireless MAC Address Wireless MAC Filtering Most users will not need this feature However if there is a PC or other d
22. B Direktyvos nuostatas Hierbij verklaart Zoom Telephonics Inc dat het toestel Zoom ADSL Modem Router w Wireless N in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Hawnhekk Zoom ADSL Modem Router w Wireless N jiddikjara li dan Zoom Telephonics Inc jikkonforma mal ti ijiet essenzjali u ma provvedimenti o rajn relevanti li hemm fid Dirrettiva 999 5 EC Alul rott Zoom Telephonics Inc nyilatkozom hogy a Zoom ADSL Modem Router w Wireless N megfelel a vonatkoz alapvet k vetelm nyeknek s az 1999 5 EC ir nyelv egy b el r sainak Niniejszym Zoom Telephonics Inc o wiadcza e Zoom ADSL Modem Router w Wireless N jest zgodny z zasadniczymi wymogami oraz pozosta ymi stosownymi postanowieniami Dyrektywy 1999 5 EC Zoom Telephonics Inc declara que este Zoom ADSL Modem Router w Wireless N est conforme com os requisitos essenciais e outras disposi es da Directiva 1999 5 CE Zoom Telephonics Inc izjavlja da je ta Zoom ADSL Modem Router w Wireless N v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo ili direktive 1999 5 ES Zoom Telephonics Inc t mto vyhlasuje e Zoom ADSL Modem Router w Wireless N sp a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES Zoom Telephonics Inc vakuuttaa t ten ett Zoom ADSL Modem Router w Wireless N tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatim
23. CC compliant modular jack It is designed to be connected to the telephone network or premises wiring using compatible modular plugs and cabling which comply with the requirements of FCC Part 68 rules The Ringer Equivalence Number or REN is used to determine the number of devices which may be connected to the telephone line An excessive REN may cause the equipment to not ting in response to an incoming call In most areas the sum of the RENs of all equipment on a line should not exceed five 5 0 In the unlikely event that this equipment causes harm to the telephone network the telephone company can temporarily disconnect your service The telephone company will try to warn you in advance of any such disconnection but if advance notice isn t practical it may disconnect the service first and notify you as soon as possible afterwards In the event such a disconnection is deemed necessary you will be advised of your right to file a complaint with the FCC From time to time the telephone company may make changes in its facilities equipment or operations which could affect the operation of this equipment If this occurs the telephone company is required to provide you with advance notice so you can make the modifications necessary to obtain uninterrupted service There ate no user serviceable components within this equipment See Warranty flyer for repair or warranty information It shall be unlawful for any person within the United Sta
24. Ensure that the DNS Server Search Order box contains 192 168 1 1 Appendix D TCP IP Network Settings 95 Appendix E Configuring Your Web Browser Important This section is for Windows computers only If you are using a Mac computer your browser is already configured properly However you must ensure that your computer s TCP IP settings are configured properly See Macintosh TCP IP Settings on page 90 for instructions on how to do this When using a Windows computer the software that you use to make an Internet connection must be set for a network connection not a dial up connection This configuration should have been done automatically when you installed the software If you find that you need to configure your Web browser this section includes instructions for recent versions of two popular Web browsers Internet Explorer Version 5 0 or later and Mozilla Firefox 3 x The configuration is done on the same computer on which you installed the X7N software Depending on the browser you have on your Windows computer follow the corresponding instructions in this section Tip If you are using an earlier version of one of these browsers the configuration may be slightly different from below In those cases or if you are using another browser altogether configure the browser to use a network connection this might be called a Local Area Network or broadband connection Appendix E Configuring Your Web B
25. If your ADSL service provider is not shown below first use the settings for Service Provider Not Shown at the bottom of the table If those settings do not work use the settings for the company that provides local telephone service in your area Table A USA ISP VPI VCl Encapsulation All Tel 1 0 35 PPPoE LLC All Tel 2 0 35 1483 Bridged IP LLC AT amp T 1 0 35 PPPoE LLC AT amp T 2 8 35 1483 Bridged IP LLC AT amp T 3 0 35 1483 Bridged IP LLC August net 1 8 35 1483 Bridged IP LLC August net 2 0 35 1483 Bridged IP LLC BellSouth 8 35 PPPoE LLC Castle Net 0 96 1483 Bridged IP LLC CenturyTel 1 8 35 PPPoE LLC CenturyTel 2 8 35 1483 Bridged IP LLC Coqui net 0 35 PPPoA LLC Appendix B ADSL Internet Settings Tables X7N User Manual Covad 0 35 PPPoE LLC ra Ed 33 PPPOELEC Earthlink 1 0 35 PPPoE LLC Earthlink 2 8 35 PPPoE LLC Earthlink 3 8 35 PPPoE VC MUX Earthlink 4 0 32 PPPoA LLC Eastex 0 100 PPPoA LLC Embarq 8 35 1483 Bridged IP LLC 4DV net 0 32 PPPoA VC MUX Frontier 0 35 PPPoE LLC io A 34 PPPOE LLG GWI 0 35 1483 Bridged IP LLC Hotwire 0 35 1483 Bridged IP LLC Internet Junction 0 35 1483 Bridged IP LLC PVT 0 35 1483 Bridged IP LLC Qwest 1 0 32 PPPoA VC MUX Qwest 2 0 32 PPPoA LLC Qwest 3 0 32 PPPoE LLC Qwest 4 0 32 1483 Bridged IP LLC SBC 1 0 35 PPPoE LLC SBC 2 0
26. This is done by setting up a DMZ or virtual server or by using port triggering so that the modem s firewall won t block the other players from your system during your gaming The main difference between the three methods is the amount of access someone has to your system A virtual server will allow access to your computer or gaming station on certain ports A port is a channel that is used by applications such as games for communication For example the directions for the game you want to play over the Internet might tell you to open up port 6000 Port triggering works by sensing when data is sent out on the predetermined outgoing port and then automatically opening up the corresponding incoming port s It will automatically forward the traffic on the incoming port to the computer that accessed the outgoing port If your game uses one port to send outgoing data and a different port or ports for incoming data you may want to use port triggering The advantage of port triggering is that it is more secure than setting up a virtual server since the incoming port is only open when you are using it and since it tracks which computer sent the outgoing data Port triggering can also be easier to set up because you do not need to know the IP address of your gaming station The disadvantage of port triggering is that only one host can be accessing the port at one time so if you have two computers or game stations playing the same game on your n
27. Window 2 Under Connect via select Ethernet built in 3 Under Configure select Using DHCP Server Do not enter anything in the DHCP Client ID field 4 Close the TCP IP Window You will be asked if you want to save the changes Click Save 5 Continue with Logging into the Configuration Manager on page 14 Appendix D TCP IP Network Settings 91 Windows TCP IP Settings How you configure your Windows computer s network settings differs depending on your operating system Windows 7 Users 1 2 5 6 From the desktop click the Start button select Control Panel Under Network and Sharing Center select Change adapter settings from the menu on the left side of the screen Right click on the Local Area Connection icon and select Properties In the Local Area Connection Properties dialog box highlight Internet Protocol Version 4 TCP Ipv4 and click the Properties button e Ifyou are using DHCP most users Ensure that Obtain an IP address automatically is selected and that either Obtain a DNS server address automatically or Enable DNS is selected All fields should be blank e Ifyou are using a static IP address Ensure that Use the following IP address and Use the following DNS server addresses ate selected and that the correct IP address Subnet mask Default gateway and Preferred DNS server values appear Click OK twice Re enter 192 168 1 1 in your Web browser s address bar Windows Vista Us
28. X7N USER MANUAL IN NOTICE This document contains proprietary information protected by copyright and this Manual and all the accompanying hardware software and documentation are copyrighted No part of this document may be photocopied or reproduced by mechanical electronic or other means in any form The manufacturer does not warrant that the hardware will work properly in all environments and applications and makes no warranty or representation either expressed or implied with respect to the quality performance merchantability or fitness for a particular purpose of the software or documentation The manufacturer reserves the right to make changes to the hardware software and documentation without obligation to notify any person or organization of the revision or change All brand and product names are the trademarks of their respective owners O Copyright 2011 All rights reserved Contents Contes ars 3 A T E 6 Installation Instructions oooconocnnnnnnnncnnnnnnnrnnnrnnnrnnnrnnnncnnn na 7 Package Contents cusitadiansiildtds 7 Before You Begin ssssssssssrrrrrsssssrrrrnnnnssssrnrrnrnneeeeene 8 Installing the PIS caida iimabada tarada ico 9 To Install the X7N on a Windows Computer use the Install ASStA Nt en 9 Installing your X7N on a Macintosh or other computer does not use Install Assistant ooooonnncccc nnnincccccannnos 10 Logging into the Configuration Manager 15 Setting Up a Netw
29. a frve channel Chapter 4 Connecting Devices Wirelessly to the X7N X7N User Manual difference between your network and those of your neighbors Having less than a five channel difference may result in interference with your connection By default the X7N uses channel 10 If you need to change this channel you must do so using the Wireless Setup page of the Zoom Configuration Manager For instructions on how to log in to the Zoom Configuration Manager see page 14 After logging in select Wireless from the left side menu On the Wireless page you can select a new channel from the drop down menu To disconnect from the current network 1 On your Windows desktop click the Wireless Network Icon button in the system tray 2 Select Zoom and click on Disconnect Connecting a Wireless enabled Computer or Device including the iPhone or other cellular phones the iPod Touch etc to the X7N 1 Go to the wireless enabled computer or device that you want to add to the network The device should have software that will let it perform a site search to scan for available wireless networks in your area You may have to click on something like Settings and then Wi Fi When the wireless network name you gave your network in Chapter 3 appears or if you did not change the Wireless Network name the default name Zoom should appear select it as the network you want to use to connect to the Internet e If you secured your wireless network in
30. amed button 35 Wireless Options This chapter is primarily for technically advanced users For most people the options that are set by default when the X7N is installed are sufficient The information in this chapter applies to you if e You wish to change the name of your Wireless Network e You want to set up a guest wireless network that provides limited access to your network e You want to turn off or hide your wireless network e You want to enable MAC Filtering to prevent a device on your network from accessing the network or as an added layer of security to only allow devices that you specify to access your network e You want to set up the X7N to work with wireless repeaters to extend the range of your network e You want to view the wireless devices that are connected to your network Chapter 5 Wireless Options X7N User Manual To configure wireless features click Wireless from the left side menu of the Zoom Configuration Manager This link Basic Security MAC Filtering WDS Advanced Client Info Opens a page that lets you Configure basic features of the witeless LAN interface On this page you can change the name of your wireless network turn off or hide your wireless network or set up a guest network Configure security features of the LAN interface See Chapter 3 Setting Wireless Security on page 19 Configure wireless MAC filtering to block Internet access Config
31. blank If you are using a static IP address Ensure that Use the following IP address and Use the following DNS setver addresses are selected and that the correct IP address Subnet mask Default gateway and Preferred DNS server values appeat Windows 98 Me 1 Open the Internet Protocol TCP IP Properties dialog box Appendix D TCP IP Network Settings X7N User Manual a From the desktop click the Start button point to Settings then Control Panel b Double click the Network icon to display the Network dialog box Cc Select your NIC card s TCP IP entry it should include TCP IP in it but not AOL Dial up or Adapter and click the Properties button and then click OK 2 Ensure the following is selected depending on whether you are using dynamic DHCP or static IP addressing e If you are using DHCP most users Ensure that Obtain an IP address automatically is selected and that either Obtain a DNS server address automatically ot Enable DNS is selected All fields should be blank e If you are using a static IP address Ensure that Use the following IP address and Use the following DNS setver addresses are selected and that the correct IP address Subnet mask Default gateway and Preferred DNS server values appear On the DNS Configuration tab ensure that Enable DNS is selected and that something appears in the Host box If not enter any name word or combination of letters and numbers
32. ce was working at your location and you are replacing an ADSL modem read this It s important to know whether your ADSL service requires the modem to have a User Name and Password to access and browse the Internet This User Name and Password may be different from the User Name and Password used to access a service provider s email or to log in to the modem s Configuration Manager If your ADSL service DOES require a User Name and Password be sure to write down the ones you ve been using They will be useful when you install your Zoom modem If your ADSL service DOES NOT require a User Name and Password please be aware that some of these services require you to disconnect yout old modem for at least 2 hours before installing a new modem including your Zoom modem e Atleast one computer for setting up the X7N The X7N supports Macintosh Linux and Windows operating systems e Ifyou plan to connect more than one computer directly to the modem you will need additional Ethernet cables to make the connection The modem supports up to four direct connections with its four ETHERNET ports Chapter 1 Installation Instructions X7N User Manual Installing the X7N Important The X7N should be installed near a phone jack with ADSL service Ideally it should be located so that it s not too far from any wireless devices that will communicate with the X7N Sometimes 1t s helpful to set up the X7N at one location and to then mov
33. ch computer or other device added to your wireless network you will need to take appropriate steps for setting up that computer or other device To do that select one of the possibilities for that computer or other device below gt Many newer Windows 7 Vista and XP computers have built in wireless networking capabilities and do not require the installation of a wireless component If this is the case you should set up that computer s wireless connection using the Windows 7 Vista or XP connect utility See the sections below on connecting Windows 7 page 26 Vista page 28 or XP page 30 computers with built in wireless capabilities gt Some computers may have built in wireless networking capabilities but do not use the Windows 7 Vista or XP utility to configure their device If this is so set up your computer s wireless connection using the instructions on page 30 for Connecting a 25 Wireless enabled Computer or Device to the X7N gt Ifyou have a non computer wireless device like an iPhone or other cellular phone iPod Touch etc see the instructions on page 30 for Connecting a Wireless enabled Computer or Device to the X7N gt Some computers may need a wireless network adapter installed This can be a USB adapter PC Card adapter or PCI adapter When you install the adapter make sure that it is set to infrastructure or access point mode NOT ad hoc or peer to peer mode If you need help installing yo
34. ctions to block a child from accessing the Internet until you are home To open this page click Advanced Setup gt Parental Control Then click on Time Restrictions The following table describes the Time Restriction settings Setting User Name MAC Days of the Week Start Stop Remove Description The name you wish to give this rule Enter the MAC Address of the computer you wish to block To find the MAC address of the devices connected to your X7N ate shown in the Existing DHCP Clients table at the bottom of the page Select the days of the week that you wish to block access on Enter the starting time that you wish to block access Enter the time that you wish to block access until Click Remove to remove an entry 59 Setting Up a Static Routing Table Do need static routing Most users do not need to set up static routes The default route used in your modem will forward all packets correctly However 1f you set up your network with different subnets you can use static routing to ensure your packets are handled correctly You can manually create a static route to tell the modem how to reach a specific IP network The route entry specifies a destination network or single host together with a mask to indicate what range of addresses the network covers and a next hop gateway address or interface If there is a choice of routes for a destination the route with the most specific mask is c
35. d so that you can use the new User Name and Password with your Zoom modem Some service providers like Verizon provide a software tool that lets you do that if your old moden is still plugged in Many service providers allow you to change your User Name and Password on their support website in case you have forgotten this information e Ifyou are not replacing a modem you may need to use y pacing gt Y y your service provider s Internet software tool or speak Appendix A Troubleshooting Tips 75 with the service provider to find out your User Name and Password e Remember that the User Name and Password ate case sensitive so it matters whether a letter is a capital letter or a small letter so does the difference between the letter O and the number 0 e Once you have a working User Name and Password be sure to remember them You may want to write them on the bottom of the X7N case for instance and in a ModemSettings file e We are talking here about the User Name and Password to get into the Internet NOT the User Name and Password used to get into your modem s configuration page Problem Autodetecting the connection through either the Install Wizard or the Zoom configuration manager was unable to detect my connection Solution There are several issues that could cause this problem Check these items Your DSL connection is not established You must wait for your DSL connection to be established before r
36. ddress of the next device interface or Internet destination to forward data to based on the ultimate destination of the data A maximum of 32 routes can be configured RIP Sets the X7N to use Routing Information Protocol RIP Most users will not set this Chapter 8 Advanced X7N Setup Options X7N User Manual DNS DSL UPnP DNS Proxy Interface Grouping IPSec Certificate DNS Server Allows you to specify multiple DNS servers Typically most users do not need to enter a DNS server unless instructed by their ISP Dynamic DNS Allows you to map a dynamic IP address to a static address allowing yout DSL router to be mote easily accessed from various locations on the Internet Typically used to host a website behind your router without paying for a static IP address To set DSL settings Modulation and capability can be selected from lists on this page DSL Advanced Settings can also be found on this page Allows you to enable disable UPnP UPnP allows other UPnP software or devices to work together without user intervention The default setting for UpnP is Enabled When Enabled default setting attached LAN devices performing DHCP release renew will have the router s LAN IP assigned as the DNS Server and the X7N acts as a DNS Proxy When Disabled the X7N no longer acts as a Proxy and assigns to LAN DHCP devices it s own DNS servers that it uses can be used if the servers are down and you want
37. device such as a wireless access point router hub or switch Check these items e Try rebooting each computer on your network For example if you are using a router reboot each computer that is connected to the router This will allow for the computers to release and renew their IP addresses Appendix A Troubleshooting Tips X7N User Manual e If you are using a wireless access point or a router verify that the device is using Dynamic Host Configuration Protocol DHCP This is also known as dynamic IP addressing Depending on your device this may be controlled by an Obtain an IP address automatically option If you need help refer to the documentation that came with your network device or contact its manufacturer e Refer to the documentation provided with your network device or contact its manufacturer for assistance Appendix A Troubleshooting Tips 81 Appendix B ADSL Internet Settings Tables These tables are for customers where ADSL settings were not automatically detected by the X7N Install Assistant and whose service providers do not supply them with the ADSL settings to connect to the Internet Many ADSL providers use different settings depending on the region in which they are operating which is why there may be more than one setting for your service provider We post updated tables on our Web site If your country is not listed in the tables below please consult www zoomtel com Note to USA customers
38. dique le nombre maximal de terminaux qui peuvent tre raccord s a une interface t l phonique La terminaison d une interface peut consister en une combinaison quelconque de dispositifs la seule condition que la somme d indices d quivalence de la sonnerie de tous les dispositifs n exc de pas 5 European Declaration of Conformity The manufacturer declares under sole responsibility that this equipment is compliant to Directive 1999 5 EC R amp TTE Directive via the following This product is CE Marked Directive Standard Test Report 73 23 EEC Low EN60950 1 2006 A11 2009 Electrical safety Voltage 1EC60950 1 2005 89 336 EEC EMC EN 301 489 1 v1 6 1 2005 09 EN EMC immunity 301 489 17 1 2 1 2002 EMC emissions EN 55022 2006 Class B Electrostatic Discharge Statement The unit may require resetting after a severe electrostatic discharge event Note If you do not use the supplied phone cord use an equivalent of minimum AWG 26 line cord CAUTION To reduce the risk of fire use only No 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord Europe EU Declaration of Conformity This device complies with the essential requirements of the R amp TTE Directive 1999 5 EC The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R amp TTE Directive 1999 5 EC EN 60950 1 2006 Safety of Information Tec
39. dustry Canada Terminal Equipment Technical Specifications This is confirmed by the registration number The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met It does not imply that Industry Canada approved the equipment AVIS Le pr sent mat riel est conforme aux sp cifications techniques d Industrie Canada applicables au mat riel terminal Cette conformit est confirm e par le num ro d enregistrement Le sigle IC plac devant le num ro d enregistrement signifie que Penregistrement s est effectu conform ment une d claration de conformit et indique que les sp cifications techniques d Industrie Canada ont t respect es Il n implique pas qu Industrie Canada a approuv le mat riel NOTICE The Ringer Equivalence Number REN for this terminal equipment is 0 1 The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an Appendix H Regulatory Information interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five AVIS L indice d quivalence de la sonnerie IES du pr sent mat riel est de 0 1 LIES assign a chaque dispositif terminal in
40. e X7N See Chapter 4 for details on connecting different wireless devices to your network If you do not need help connecting your wireless devices to your X7N you may choose to continue with gt Chapter 6 to learn about using the X7N with online gaming gt Chapter 7 to learn about monitoring your ADSL Status Most users will not need to use status monitoring gt Chapter 8 to learn about the advanced features of the X7N Most users will not need to change advanced features Setting Up Security Using WEP If even one of your wireless network devices DOES NOT support WPA2 or WPA you need to use WEP to configure network security WEP can be configured two ways 64 bit and 128 bit 128 bit WEP provides a bit more security than 64 bit but 128 bit WEP also tends to diminish network performance We recommend that most people configure their WEP for 64 bit security 1 Open the Zoom Configuration Manager by typing the following in your Web browser s address bar http 192 168 1 1 2 Inthe Enter Network Password dialog box type the following User Name and Password in lower case then click OK User Name admin 21 Password zoomadsl The User Name and Password entered here are not the same as the user name and password that your Internet service provider may have given you 3 Click Wireless on the left side menu of the Configuration Manager 4 Inthe SSID Wireless Network Name field assign a name to you
41. e basic instructions needed to install your X7N and connect to the Internet These instructions can be used by those with a Windows Macintosh or Linux operating system If you already installed and connected your X7N by for instance using the separate Quick Start you can skip this chapter and begin with Chapter 2 Setting up a Network on page 17 Package Contents Your package contains the following items Zoom X7N ADSL modem router Ethernet cable Power cube One long phone cord A splitter to enable you to use a single ADSL wall jack for both an Internet connection and for telephone service certain countries only Some splitters ship with a second phone cord attached to the splitter and others ship with a separate second phone cord Quick Start flyer CD contains the installation software documentation warranty and Customer Support information If anything is missing or damaged please contact Zoom Customer Support see Appendix G Getting Help or whoever sold you the modem Before You Begin Before you begin installing the X7N modem using this manual you must have the following available to you e ADSL service enabled on your telephone line To do this you need to sign up with an ADSL service provider Once this service is enabled you should have an ADSL enabled telephone wall jack to plug the X7N modem into Your service provider may refer to ADSL service as DSL service e If ADSL servi
42. e between any one of the modem s available ETHERNET ports and any of the network device s available Ethernet ports For a hub or a switch this is typically called an Uplink or Expansion port For a router this is typically called a WAN port Set up your network and or device Refer to the documentation provided with your particular network device for instructions on how to do this Once your network device is set up reboot any computer that is part of the network Verify that your Internet connection is working for a computer using the network device Open that computer s Web browser for instance Internet Explorer Firefox or Chrome on each computer and try to connect to a familiar Web address Congratulations You have set up your wired devices If you have wireless devices that you want to add to your network start with Setting Wireless Security on page 19 Chapter 2 Setting Up a Network X7N User Manual Setting Wireless Security Wireless security is turned off by default on your X7N This means that your wireless signal is not encrypted and that anyone with compatible wireless technology can access your computer network and the Internet using your wireless connection Before you first set up your X7N wireless network read this chapter to set up wireless security to protect your network and Internet connection Overview Before setting up wireless security you need to decide which method to use e Most pe
43. e de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage recu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable IMPORTANT NOTE For mobile device use Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body NOTE IMPORTANTE Pour l utilisation de dispositifs mobile D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contrdl Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps Industry Canada CS03 Statement Notice The Indu
44. e it to a location that gives better wireless performance Important Safety Measures To reduce the risk of fire use the supplied phone cord Do not use this product near water for example in a wet basement or next to a swimming pool gt Macintosh and Linux users please go to page 10 To Install the X7N on a Windows Computer use the Install Assistant 1 Turn on the Windows computer that you will use for setup This can be any Windows 7 Vista XP 2000 Me or 98 computer with an available Ethernet port 2 Insert the supplied CD into the CD drive of your computer The CD should start automatically 3 Follow the on screen prompts for the Install Assistant Note to Windows 7 users You may see a message box that says your software may not have installed correctly You can safely ignore this message box Now check that your installation worked by opening a Web browser and connecting to your favorite web site If you cannot connect to the Web please refer to Appendix A Troubleshooting Tips If you want to connect other computers or other devices to the X7N by using a wired Ethernet connection please continue with Chapter 2 Setting Up a Network on page 17 Installing your X7N on a Macintosh or other computer does not use Install Assistant 1 Shut down the computer that you want to connect to the X7N 2 Connect the power adapter to the receptor on the back panel of your X7N and plug the other end of
45. e wall without sharing that jack with a telephone If you ate using a filter splitter with a phone only and not a modem connect the filter splitter s LINE or PHONE LINE jack to a phone jack in the wall then plug the phone into the filter splitter s PHONE jack Some but not all filter splitters require you to use a short phone cord to connect the filter splitter to a phone jack in the wall Phone acta et oe 7 b p E A e Filter Wall telephone jack 6 After a few seconds your DSL LED will begin blinking then become solid If the DSL LED does not become solid please refer to the Appendix A Troubleshooting Tips 7 Refer to Logging into the Configuration Manager on page 14 and then continue with Step 6 8 After you log in use the Basic Setup page to configure the modem so it can connect with your Internet service provider e We recommend you use Automatic Configuration to set up your ADSL connection unless you have requested and typically paid for a Static IP from your service provider To use Automatic Configuration recommended a Under Automatic Configuration click Start b Ifthe X7N finds a PPPoE or PPPoA connection enter the user name and password given to you by your Internet Service Provider Your provider should have given you a User ID or User Name usually your email address or the characters preceding the sign in your email address and a Password These are NOT the User ID and Password
46. een the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Operations in the 5 15 5 25GHz band are restricted to indoor usage only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Note The country code selection is for non US model only and is not available to all US model Per FCC regulation all WiFi product marketed in US must fixed to US operation channels only Industry Canada Emissions Statement This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num riqu
47. elect WPA2 instead of mixed WPA2 WPA 1 To use WPA2 WPA mode all clients that you plan to put on the network need to support WPA2 or WPA In the unlikely event that one does not skip to Setting Up Security Using WEP on page 21 2 Open the Zoom Configuration Manager by typing the following in your Web browser s address bar http 192 168 1 1 3 Inthe Enter Network Password dialog box type the following User Name and Password in lower case then click OK User Name admin Password zoomadsl The User Name and Password entered here ate not the same as the user name and password that your Internet service provider may have given you 4 Click Wireless on the left side menu of the Configuration Manager 5 In the SSID Wireless Network Name field assign a name to yout wireless network This is the name that all your wireless devices will connect to You can leave the default name Zoom if you wish 6 Then click Security on the left side menu and from the drop down menu for Select SSID select the name you just assigned in step 5 Chapter 3 Setting Wireless Security X7N User Manual 7 From the Network Authentication drop down menu select Mixed WPA2 WPA 8 Inthe WPA Pre Shared Key text box enter a passphrase of your choice 9 Write down this passphrase and put it where you can find it on the bottom of the X7N case for instance 10 Click Save Apply Now you will need to connect all your wireless devices to th
48. elephonics Inc declara que el Spanish Zoom ADSL Modem Router w Wireless N cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE letran ME THN HAPOYSA Zoom Telephonics Inc AHAQNEI OTI Greek Zoom ADSL Modem Router w Wireless N EYMMOPOOQNETAI IPOE TIX OYXIQAEBL AMATTHZED KAI TIX AOTIE2 EXETIKEX AJATAZSEL THE OAHTIAZ 1999 5 EK Lit Francais Par la pr sente Zoom Telephonics Inc d clare que l appareil Zoom French ADSL Modem Router w Wireless N est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Lit Italiano Con la presente Zoom Telephonics Inc dichiara che questo Zoom Italian Latviski Latvian Lietuvi Lithuanian Lil Nederlands Dutch ut Malti Maltese hub Magyar Hungarian LE Polski Polish Portugu s Portuguese Slovensko Slovenian Slovensky Slovak Suomi Finnish ADSL Modem Router w Wireless N conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Ar o Zoom Telephonics Inc deklar ka Zoom ADSL Modem Router w Wireless N atbilst Direktivas 1999 5 EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem iuo Zoom Telephonics Inc deklaruoja kad is Zoom ADSL Modem Router w Wireless N atitinka esminius reikalavimus ir kitas 1999 5 E
49. ers 1 2 From the desktop click the Start button select Control Panel and then double click Network and Sharing Center In the Network and Sharing Center window under Tasks select Manage Network Connections In the Network Connections window double click the Local Area Connection option In the Local Area Connection Status dialog box click the Properties button Appendix D TCP IP Network Settings X7N User Manual 5 In the Local Area Connection Properties dialog box highlight Internet Protocol Version 4 TCP Ipv4 and click the Properties button e If you are using DHCP most users Ensure that Obtain an IP address automatically is selected and that either Obtain a DNS server address automatically ot Enable DNS is selected All fields should be blank e If you are using a static IP address Ensure that Use the following IP address and Use the following DNS setver addresses are selected and that the correct IP address Subnet mask Default gateway and Preferred DNS server values appeat 6 Click OK then click Close 7 Re enter 192 168 1 1 in your Web browser s address bar Windows XP 1 Open the Internet Protocol TCP IP Properties dialog box a From the desktop click the Start button point to Control Panel and then click Network and Internet Connections b Click Network Connections C Right click the Local Area Connection icon and select Properties d Select your NIC card s TCP IP entry it sh
50. essage You Are Already Connected To The Internet will display You do not need to proceed further The browser is already setup successfully using the wired Ethernet connection If you select Set up a new connection anyway you will be displayed options to setup a different connection type that your PC supports PPPoE connection and a Wireless connection Since the X7N device is not wireless and will not Appendix E Configuring Your Web Browser 97 work with a PPPoE connection type by default then you do not need to setup either of these and can use the existing wired connection successfully Configuring Internet Explorer Version 7 0 The following instructions are for Internet Explorer Version 8 0 If you are not sure what version you have open Internet Explorer and from the Help menu choose About Internet Explorer The version number is directly below the Microsoft Internet Explorer logo You can ignore all the numbers after the period following the first digit Note If you are using Windows 7 you do not need to do anything since it will be configured automatically Internet Explorer can be configured to use a specific connection but by default will use the correct default active connection However if you want to manually setup a different connection 1 On the desktop double click the Internet Explorer icon Tip If you cannot access Internet Explorer in this way open your computer s Control Panel click the
51. etwork you will need to use a virtual server or DMZ A DMZ differs from a virtual server in that it allows access on all ports of the computer Because of this DMZs are less secure and should be used with caution on your computer However DMZs work well with your gaming stations since security is not as much Chapter 6 Online Gaming X7N User Manual of an issue for gaming stations as it is for computers Once you ve decided what type of security to use for gaming you can set up that security using the appropriate section of this manual e Virtual Server For instructions on how to set up a virtual server please refer to page 54 e DMZ For instructions on how to set up a DMZ please refer to page 56 e Port Triggering For instructions on how to set up port triggering please refer to page 57 43 Status Monitoring This chapter discusses how to check the status of your modem and its ADSL connection Most users can skip this chapter as it is primarily for advanced users and for those who are instructed by their Internet service provider or Zoom Technical Support to verify settings usually for troubleshooting If you skip this section you should go to Chapter 8 Why Monitor Status The X7N provides easy to read screens for you to review the status of the modem and its ADSL connection While most users will probably never need to check the status there are some cases in which it would be helpful For example
52. evice on the X7N network that you don t want using the Internet you can use MAC address filtering to deny the device Internet access That computer or device will still be able to communicate with other devices on the LAN such as printers 39 You can also use Wireless MAC filtering to add a layer of security setting up the X7N to only allow the MAC addresses of your wireless devices to access the Internet To set up MAC Filtering click Advanced Setup on the left side menu of the Zoom Configuration Manager Click Wireless Then click MAC Filtering Follow the instructions below 1 From the Select SSID drop down menu select the wireless network that you wish to setup MAC Filtering 2 For the MAC Restrict Mode select Allow to allow only the MAC address entered to access your network Select Deny to block the MAC addresses you enter from accessing yout network Disabled will disable MAC address filtering this allows you to turn it on and off 3 Click Add to add the MAC address to filter To see the MAC address of clients that are currently connected to the X7N click on Client Info on the left side menu 4 Click Save Apply changes after you finish adding wireless clients 5 If you want to remove any of the settings click the check box next to Remove and then click the Remove button Chapter 5 Wireless Options X7N User Manual WDS WDS is used to extend the range of your wireless network Other wireless access po
53. ew configuration from this page start by clicking Add Then use the Next and Back buttons to navigate through a series of pages where you can make changes to advanced parameters such as the ATM Traffic Class and Encapsulation Mode and enabling NAT settings IGMP Multicast and WAN Service Most users should only add a new configuration if they were instructed by their service provider to do so Once you have made the changes you want on the first section click on Next to proceed to the following section Repeat this until you reach the WAN Setup Summary page Then click the Save Reboot button Chapter 8 Advanced X7N Setup Options X7N User Manual The following table describes the settings on the WAN Configuration pages and the values that you can enter The settings displayed on the page will vary according to the protocol you are using Setting Protocol Encapsulation VCI PPP User Name PPP Password ATM Traffic Class Description Your Internet Service Provider supplies this value If your service provider instructs you to use 1483 Bridged mode select 1483 Bridged NAT to take advantage of your modem s advanced routing and firewall features The encapsulation value should match your DSL provider s encapsulation The value refers to the way that data is passed over the Internet An example value is LLC Logical Link Control Your DSL provider supplies this value when you sign up for ADSL service
54. ff the DHCP Server Click Enable to turn on the DHCP Server The first IP address of a range that you specify using the Start and End IP Address settings Your modem s DHCP server will assign the IP addresses in this range at random to the computers and devices in your network The last IP address of a range that you specify using the Start and End IP Address settings Your modem s DHCP server will assign numbers from this range at random to the computers and devices in your network The maximum amount of time in hours that a device in your network will have the IP address before a new one is issued by the modem s DHCP server 53 The checkbox Configure the second IP Address and Subnet Mask for LAN interface allows you to configure a second network on the LAN side Configuring Fixed DHCP Mapping Fixed DHCP mapping is used if you want the modem to always assign the same IP address to a computer or gaming device You would want to do this if you were setting up a virtual server or DMZ using this device To set up a device with Fixed DHCP Mapping 1 Click Advanced Setup gt LAN to open the LAN page 2 Click on Add Entries 3 Enter the MAC Address of the computer or gaming station that you wish to assign a fixed IP address to Tip To find the MAC address of the devices connected to your X7N refer to the Existing DHCP Clients table at the bottom of the page 4 Enter the IP address that you always want assigned t
55. g in any order that you choose e If you want to connect additional computers directly to the X7N see To Connect Additional Wired Computers below e Ifyou want to connect a hub switch router or other device directly to the X7N see To Connect a Network Device on page 18 e If you want to connect additional computers or other devices using a wireless network you should first set up wireless security before connecting your wireless devices See Chapter 3 Setting Wireless Security on page 19 To Connect Additional Wired Computers You can connect up to four computers that have Ethernet ports directly to the X7N Shut down and power off the computer you want to connect to the X7N This is important because the computer must locate the correct IP address for the modem This is done when the computer is turned back on in step 3 below Plug an Ethernet cable between any one of the modem s available ETHERNET ports and any of the computer s available Ethernet ports Turn on the computer Verify that your Internet connection is working for that computer Open your Web browser for instance Internet Explorer Firefox or Chrome and try to connect to a familiar Web address Repeat steps 1 4 for each computer you want to add To Connect a Network Device You can use one of the ETHERNET ports on the X7N to plug in a network device for example a hub switch router or Homeplug adapter 1 Plug an Ethernet cabl
56. g Mac OS X 10 3 and above renew your IP address Point to System Preferences then choose Network Click the Configure button and then the Renew DHCP Lease button Appendix A Troubleshooting Tips 79 gt Ifyou ate using a Windows computer power off your computer then power it back on Problem The computer on which I initially installed the X7N on is connected to the Web but devices connected wirelessly to the X7N are unable to connect to the Internet Solution e Try powering off then powering on each device on your network e Verify that the devices on your wireless network are using Dynamic Host Configuration Protocol DHCP This is also known as dynamic IP addressing Depending on your device this may be controlled by an Obtain an IP address automatically option If you need help refer to the documentation that came with your network device or contact its manufacturer If you are using a Windows Mac or Linux computer refer to Appendix D TCP IP Network Settings on page 90 for directions on configuring your computer for DHCP e Your problem might be in the wireless connection Try the steps in My computer devices are not connecting wirelessly to the X7N troubleshooting tip on page 77 Problem The computer on which I initially installed the X7N on is connected to the Web but the computers connected through my network device cannot access the Internet Solution The problem is most likely with your network
57. h Internet time servers Manage the User IDs and passwords that can access the Zoom Configuration Manager This is where you can change the default password supplied to you with the X7N 65 Management gt Services A Service Control Access Control List SCL enables or disables router services for LAN WAN such as FTP HTTP ICMP and TELNET from being used Management Update Specify the path to Software the upgrade file you need to update your firmware Use the Browse button on this page to navigate to the file then click the Update Software button to perform the firmware update Management Save Reboot Click the Save Reboot button on the Save Reboot page to reboot the modem Backing Up Your Configuration Users who change the Configuration Manager settings for the X7N may want to back up their settings This will enable them to restore those settings at a later time if needed This feature may be especially useful when you receive firmware updates from Zoom Installing the update may overwrite your customized settings with default values Before you update the firmware backup your configuration Then after the firmware has been updated restore your configuration Chapter 9 Management and Diagnostics X7N User Manual Note You do not need to back up the default settings This is because you can easily restore the defaults by clicking Management gt Settings gt Restore Defaul
58. hnology Equipment EN50385 2002 Assessment of electronic and electrical equipment related to human exposute restrictions for electromagnetic fields EN 300 328 V1 7 1 2006 10 Electromagnetic compatibility and Radio spectrum Matters ERM Wideband Transmission systems Data transmission equipment operating in the 2 4 GHz ISM band and using spread spectrum modulation techniques Harmonized EN covering essential requirements under article 3 2 of the R amp TTE Directive EN 301 489 1 V1 8 1 2008 04 Electromagnetic compatibility and Radio Spectrum Matters ERM ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 1 Common technical requirements EN 301 489 17 V1 3 2 2008 04 Electromagnetic compatibility and Radio spectrum Matters ERM ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 17 Specific conditions for 2 4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2 4 GHz wideband transmission system transceiver intended for use in all EU member states and EFTA countries except in France and Italy where restrictive use applies In Italy the end user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and or for supplying public access to telecommunications and or network services Appendix H Regulatory Informa
59. hose of your neighbors Having less than a five channel difference may result in interference with your connection By default the X7N uses channel 10 If you need to change this channel you must do so using the Wireless Setup page of the Zoom Configuration Manager For instructions on how to log in to the Zoom Configuration Manager see page 14 After logging in select Wireless from the left side menu On the Wireless page you can select a new channel from the drop down menu gt If you want to secure your wireless network so it won t be accessible by others you should specify security settings To learn how see Setting Wireless Security on page 19 By default the wireless connections provided by the X7N do not have any security applied 2 Test your wireless connections From each desktop or notebook computer that you set up open your Web browser for instance Internet Explorer or Firefox and try to connect to a familiar Web address If you connect successfully you are ready to browse the Web Chapter 4 Connecting Devices Wirelessly to the X7N X7N User Manual Important To add security to your network see Setting Wireless Security on page 19 To disconnect from the current network 1 On your computer that has a wireless adapter find the wireless network connection option similar to the process of adding your computer to the network 2 Click or highlight Zoom 3 Select or click on Disconnect or similarly n
60. hosen To route to a destination that is not on any local network a route may be added via a gateway for instance another router The gateway IP address must be on the same subnet as one of the router s interfaces Click Routing from the left side menu of the Zoom Configuration Manager Click Static Route Click Add The following table describes Routing Table settings Setting Description IP Version Select IPv4 or IPv6 Destination IP Enter the Destination Network Address address prefix length Interface You can make a selection from the drop down menu Gateway Enter the Gateway IP address of your destination s subnet The HOP gateway must be on the same subnet as the modem Chapter 8 Advanced X7N Setup Options X7N User Manual Metric The number of routers that the data packets go through optional When adding a static route if you know how many hops or routers a packet must go through to reach the destination network then you can add it This is usually not a mandatory requirement If you change any of the settings click Save Apply If you want to remove any of the settings click the check box next to Remove and then click the Remove button Adding a DNS Server Name Do need to add a DNS server name Typically you should not need to enter a DNS server name as it is assigned automatically when your connection is established However your ISP may instruct you to enter an IP address fo
61. ight be called a Local Area Network or broadband connection If you need help configuring your Web browser refer to Appendix E Configuring Your Web Browser on page 96 e Verify that your TCP IP network settings are properly configured on your computer To do this refer to the appropriate section gt Ifyou are using Macintosh see Macintosh TCP IP Settings on page 90 Appendix A Troubleshooting Tips X7N User Manual gt Ifyou are using Windows see Windows TCP IP Settings on page 92 Problem My DSL connection requires a User Name and Password but I don t know where to find this information Solution e Ifyou are replacing a modem use the same User Name and Password that you used for the modem you re replacing e Ifyou don t know what that is here are some suggestions gt Ifyou have an email address with the service provider like name verizon net the User Name is likely to be the word name in this example NAME will not work since upper and lower case matter There are some exceptions to this however Some AT amp T customers especially in old BellSouth areas have a separate network User Name and password used to verify their DSL connection Please see the AT amp T support website on how to reset your User Name and password gt If you have a service provider Password that s probably your Password for Internet access too gt You may also be able to change your User Name and Passwor
62. ints that support WDS can connect wirelessly to the X7N to expand the range of your wireless network The table explains the following settings for WDS This setting AP Mode Bridge Restrict Remote Bridges MAC address Lets you specify Most usets should select Access Point to communicate with both Wireless Clients and Wireless Access points Selecting WDS means that the X7N can only communicate with other Access Points Select Disable if you want Access point to be able to bridge to the X7N Select Enabled or Enabled Scan to control which access points have access to the X7N If you know the MAC address of the Access points you wish to allow access to select Enabled and enter the MAC address in the Remote Bridges MAC address field If you don t know the MAC address select Enabled Scan to show a list of access points that you can allow access Click the check box next to each access point that you want to grant access In Enabled mode you can enter the MAC addresses of the access points you wish to associate with In Enabled Scan mode it displays a list of access points so you can select which ones to grant access Click Refresh to update the remote bridges Wait for a few seconds to update Click Save Apply to configure the wireless bridge options 4 Online Gaming If you are using your router for gaming you may need to make changes to the router s firewall setting for the game to work
63. is chapter applies to you if Your Internet service provider instructs you to enable disable or change the default settings for your X7N You need to change your Wide Area Network settings You want to change the default firewall settings to block particular IP addresses and intrusive hosts You wish to set up a DMZ Virtual Server or Port Triggering for online gaming You wish to control the hours that a user on your network can access the Internet You want to set up fixed IP addresses for your computer s Chapter 8 Advanced X7N Setup Options X7N User Manual Viewing the Advanced Setup Options For Advanced Setup options click Advanced Setup from the left side menu of the Zoom Configuration Manager This link ATM Interface WAN IPv6 Autoconfig NAT Opens a page that lets you Used to set up multiple ATM channels Most users will only do this if instructed by their setvice provider Specify how the Wide Area Network WAN ADSL setup is configured Some of the values need to be supplied by your ISP DSL provider Specify the settings that control the connection between the X7N modem and your computer Set a fixed IP address for your computer Allows you to set up IPv parameters Virtual Servers Setup page To direct incoming traffic from the WAN side A maximum of 32 entries can be configured Port Triggering To dynamically open up ports in the firewall when an application on the LAN i
64. k Start Changing Your LAN Settings When would need to change my LAN settings DHCP Dynamic Host Configuration Protocol is a protocol that enables your modem to manage the assignment of IP addresses to computers and devices on your Ethernet LAN network DHCP is enabled by default on the X7N Enabling DHCP on the X7N allows it to assign temporary IP addresses to your computers whenever they connect to your network You can control the amount of time that lapses before a new address is issued or renewed You can extend the range of IP addresses that are assigned to your network devices should you add new devices to Chapter 8 Advanced X7N Setup Options X7N User Manual your network You can also change the default LAN IP address for your modem The following table shows you the values to enter After you enter the values click Save Reboot Setting Group Name IP Address Subnet Mask Enable IGMP Snooping DHCP Server Start IP Address End IP Address Leased Time hour Description Default The IP address of your modem The modem s subnet mask address Check uncheck to Enable Disable the IGMP Snooping feature This feature is designed to prevent hosts on a local network from receiving traffic for a multicast group they have not explicitly joined Snooping is specifically useful for bandwidth intensive IP multicast applications like IPTV Most users can leave the default setting Click Disable to turn o
65. k Turn Windows features on or off Vista users only At the User Account Control message click Continue 3 In the Windows Features dialog box select Telnet Client click OK and wait while the feature is configured This normally takes about 2 minutes Appendix A Troubleshooting Tips X7N User Manual 4 Inthe Uninstall or Change a Program window click the Close box to exit You unplugged some other ADSL modem a router or some other Ethernet device from your computer and then did not power cycle your computer If this applies to you try turning your computer off and then on This ensures that your computer gets a correct IP address from the X7N Your Zoom modem s Ethernet cable is not plugged in properly or is defective Please check this cable Your computer is set to use static IP addressing This needs to be changed to Dynamic Addressing to use the Install Assistant and you can later go back to static IP addressing if that is appropriate To use Dynamic Addressing for the Install Assistant see Windows TCP IP Settings in Appendix D Problem I cannot log into the Zoom Configuration Manager I have typed http 192 168 1 1 but I am not prompted for a User Name and Password Solution There are several issues that could cause this problem Check these items e If you are using a Macintosh computer your TCP IP settings may not be properly configured See page 90 for more information e Ifyou are usin
66. lications to see if yours is on the list If it is select it You will need to enter the IP address of your computer or gaming station in the Server IP Address field but the rest of the information will be filled out for you Click Save Apply to save your new virtual server 4 If your game or application was not on the list continue to step 5 to create a custom Virtual Server 5 Enter a Custom Server name for your virtual server 6 Enter the IP address on the computer or game station that you want to use the virtual server with in the Server IP Address field 55 7 For each range of ports you need to open up enter the Starting and Ending External Ports and the Protocol used Your game documentation should provide you with this information 8 Ifyou only need to open one port enter that port number in both the Start and End External Port fields 9 Once you enter the External Ports the Internal Port fields will automatically be set to the same values The Internal ports cannot be changed 10 If you know the Remote IP address of the device you are connecting to enter it under the Remote IP field If you don t know it you can leave this field blank 11 Click Save Apply to save your new virtual server DMZ Use this page to designate a computer or gaming station on the Local Area Network as a DMZ Demilitarized Zone When you set up a DMZ for a computer all ports on that computer ate opened up to all Internet traffic
67. lly or want to connect through a local area network LAN then click Next b On the Setting up your Internet connection dialog box select I connect through a local area network LAN then click Next c On the Local area network Internet configuration dialog box uncheck the Automatic discovery of proxy server check box then click Next d On the Set Up Your Internet Mail Account dialog box select No then click Next e On the Completing the New Connection Wizard dialog box uncheck the To connect to the Internet immediately select this box check box if it appears and click Finish 4 Ifyou accessed Internet Explorer s settings from the Control Panel as explained in the Tip following step 1 the Control Panel window will still be open Close it before continuing Appendix E Configuring Your Web Browser X7N User Manual Configuring Mozilla Firefox No setup is necessary since Mozilla Firefox will use the active connection Unlike IE Firefox cannot be configured to use a specific connection type it will use whatever is available and active at the time Configuring Google Chrome No setup is necessary since Google Chrome will use the active connection Unlike IE Google Chrome cannot be configured to use a specific connection type it will use whatever is available and active at the time Appendix E Configuring Your Web Browser 101 Appendix F Wireless Channels by Country For mo
68. n that came with your wireless adapter There are several site scan issues you should be aware of gt Ifyou ate trying to connect to a wireless network that already has security enabled your wireless adapter might not recognize what type of security is on the network You may need to manually set up the security for your adapter If you need help refer to the documentation that came with your wireless adapter 33 gt Windows 7 XP and Vista users If you installed a wireless adapter on a Windows 7 XP or Vista computer Windows may try to automatically configure the adapter rather than let you use the software provided with the wireless adapter You will know this is happening because you will be prompted with a message about one or more wireless networks being available You will also be able to click a link to open the Wireless Network Connection Properties dialog box If this happens click the link clear the Use Windows to configure my wireless network settings check box and then click OK You can then use the software provided with your wireless adapter without interruption from Windows gt Mote than one wireless network may appear in the list These are other wireless networks that are within range of your network Your neighbors for instance may be within range of your network Each wireless network has a channel associated with it We recommend there be at least a five channel difference between your network and t
69. ndows desktop click the Wireless Network Icon button in the system tray 2 Windows will automatically scan for available wireless networks in your area Any compatible networks within range will appear in the Available networks list It should find the name you gave your wireless network in Chapter 3 If you did not change the Wireless Network name select the default name Zoom 3 Double click your wireless network name to connect to the X7N e Ifyou secured your wireless network in Chapter 3 in the next dialog box enter the security key or password and click Connect e If your desired network is unsecured in the message box select Connect Anyway 4 Test your wireless connection From the computer or notebook that you set up open your Web browser for instance Internet Explorer or Firefox and try to connect to a familiar Web address If you connect successfully your notebook s wireless capability is configured and you are ready to browse the Web Important If you want to add security to your network please see Setting Wireless Security on page 19 gt When you click on the wireless network option box Windows will scan for available networks More than one wireless network may appear in the list These are other wireless networks that are within range of your network Your neighbors for instance may be within range of your network Each wireless network has a channel associated with it We recommend there be at least
70. networks More than one wireless network may appear in the list These are other wireless networks that are within range of your network Your neighbors for instance may be within range of your network Each wireless network has a channel associated with it We recommend there be at least a five channel difference between your network and those of your neighbors Having less than a five channel difference may result in interference with your connection By default the X7N uses channel 10 If you need to change this channel you must do so using the Wireless Setup page of the Zoom Configuration Manager For instructions on how to log in to the Zoom Configuration Manager see page 14 After logging in select Wireless from the left side menu On the Wireless page you can select a new channel from the drop down menu 27 If you have difficulty connecting make sure you have entered the correct password if security is enabled Otherwise refer to Appendix A Troubleshooting Tips on page 70 To disconnect from the current network 1 Right click the wireless network icon in the notification area of the Windows taskbar 2 Right click Zoom and select Disconnect Connecting a Windows Vista Computer with Built in Wireless Capabilities 1 From the Start menu select Connect to 2 Inthe Connect to a network dialog box highlight the name you gave your wireless network in Chapter 3 If you did not change the Wireless Network name select
71. nge the wireless channel In the unlikely event that you experience performance issues with your wireless network you may want to set your network up on a channel that s different from the factory set channel of 10 To do that follow these steps 1 Open the Zoom Configuration Manager by entering the following in your Web browser s address bar http 192 168 1 1 2 In the Enter Network Password dialog box type the following User Name and Password in lower case then click OK User Name admin Passwotd zoomadsl Appendix A Troubleshooting Tips 77 The User Name and Password entered here are not the same as the user name and password that your Internet service provider may have given you 3 On the Basic Setup page click Wireless on the left side menu to open the Wireless page 4 On the Wireless page from the Channel drop down menu select a different channel such as 1 ot 6 5 Be sure to click Save Apply after you change the channel All devices connecting wirelessly to the X7N will automatically switch to the new channel Problem When I run the Zoom Install Wizard it reports that my DSL modem is not found Solution e Verify that your X7N is powered on The Power led should be on e You are using Windows Vista or Windows 7 and Telnet is not enabled To enable Telnet 1 Click Start select Control Panel then double click Programs and Features 2 In Programs and Features in the Tasks pane clic
72. nitiates a TCP UDP connection to the remote application using a Triggering Port A maximum of 32 entries can be configured DMZ Host To forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer 47 Security gt IP Filtering Security gt MAC Filtering Parental Control gt Time Restriction Parental Control gt URL Filtering QoS Quality of Service Routing Outgoing To block selected IP traffic by setting up filters Incoming To accept selected IP traffic by setting up filters when the firewall is enabled Allows you to block access to the Internet based on a device s MAC address Allows control of when certain computers or devices are allowed to access the Internet To choose particular URLs to be excluded or included by setting up a URL list A maximum of 100 entries can be configured This lets you assure better performance for gaming and VoIP Queue Management Configuration Allows you to automatically mark incoming traffic without reference to a particular classifier Queue Configuration Allows you to configure a maximum of 24 entries QoS Class Allows you to configure network traffic classes Default Gateway Set up the routes on which you want the X7N to send data that it receives on a particular interface such as a LAN or Ethernet interface Static Route Routes specify the IP a
73. o your computer or gaming station This address can be the one already given to it on the DHCP Status page or can be an unused IP address For example if none of the devices on the DHCP Status page have been assigned 192 168 1 25 you can use that as the IP address 5 Click Save Apply to store your settings You can remove entries by clicking on Remove Entries Click Save Apply Chapter 8 Advanced X7N Setup Options X7N User Manual Creating a Virtual Server a DMZ or Using Port Triggering Do need to create a virtual server DMZ or use Port Triggering By default your modem uses Network Address Translation NAT to hide your computers from users on the Internet However there may be times when you want to allow access by outside users to a computer or gaming station on your network For instance you would want to allow access if a computer in your network is hosting Internet games or running a web server If you wish to set up your X7N for online gaming you should refer to Chapter 6 Online Gaming to help you decide whether a Virtual Server DMZ or Port Triggering is right for you Creating a Virtual Server Before starting this section you should specify a fixed DHCP address for the computer or gaming station that you want to use with the virtual server 1 Click Advanced Setup gt NAT gt Virtual Servers gt Add to open the Add Virtual Servers page 2 For the server name check the list of predefined games and app
74. ople should use the X7N s Configuration Manager to setup their wireless security unless they know that all their devices support WiFi Protected Setup WPS Most people should refer to Setting Up Security Manually below e You can use Wi Fi Protected Setup WPS if all of your devices support WPS security WPS is easy to configure Please refer to WPS Configuration on page 23 for details Setting Up Security Manually To manually set up wireless security you will create and enter a unique passphrase or an alphanumeric key Once entered only devices with the proper key or passphrase will be allowed to establish a connection to the network There are two basic ways to configure and implement a passphrase ot key They are WPA2 WPA and WEP The X7N supports 19 WPA2 WPA mixed mode which lets you connect with devices that support either standard We recommend you use this setting unless you want to use on your network a wireless device that only supports WEP security In the unlikely event that you need to use WEP skip to Setting Up Security Using WEP on page 21 Setting Up Security Using Mixed WPA2 WPA mode WPA2 and WPA use a passphrase that you choose and enter on the X7N and other wireless devices on the network clients to set up security To use Mixed WPA2 WPA all of the wireless devices on your network must support either encryption method If you know that all your devices support the more secure WPA2 you can s
75. ork together There is no setup for you to do Change this setting only if you have a good reason to do so To change the status of Universal Plug and Play go to the LAN page under the Advanced Setup link Setting Description Enable UPnP Select this check box to enable or disable Universal Plug and Play By default UPnP is enabled Click Save Apply Chapter 8 Advanced X7N Setup Options X7N User Manual Management and Diagnostics Please read this chapter if you want to perform modem management functions as discussed below or if you want to run diagnostics to diagnose a modem problem If you don t want to do either of these things your modem is probably set up and ready to go You may want to read Appendix C Top and Back Panels on page 88 for details about the modem s lights and back panel jacks The information in this chapter applies to you if you wish to e Backup your current settings of the X7N so you can later restore them e Restore the X7N to its factory default settings e Change the username and password that you use to access your X7N e Provide your service provider remote access to your X7N for troubleshooting purposes Management Buttons The buttons in the Management group of the Zoom Configuration Manager are typically used for administrative tasks such as upgrading firmware changing your Zoom Configuration Manager password etc The following table lists each button in the Management g
76. ork oocoonnonnncccccocoonncccnanoncnnononnnnanananannnos 17 Setting Wireless Security ooomonccconnnnnnnnnnncnnnccnnanennnnnannnns 19 OVA a ls 19 Setting Up Security Manually oooooccnnicccnnncccconnnaccccno 19 Setting Up Security Using Mixed WPA2 WPA mode20 Setting Up Security Using WEP ooonnccccnnccccccnnnanccco 21 Connecting Devices Wirelessly to the X7N 25 Connecting a Windows 7 Computer with Built in Wireless CapabilitieS o o occccncccnnonioconccccnnnnnnno 26 Connecting a Windows Vista Computer with Built in Wireless CapabilitieS oo o occccnncnnnoniccorccccnnnnnnno 28 Connecting a Windows XP Computer with Built in Wireless CapabilitieS coooonoocccnnnnnicccnnnoncccnrnannnns 30 Connecting a Wireless enabled Computer or Device including the iPhone or other cellular phones the iPod Touch etc to the X7N 2 0 00 ccc eeeeeeeeeeeeeeeeeeeeeeeeeeees 31 Connecting a Computer with a Wireless adapter to the Pel cpasiatcoacate Ven E E 33 Wireless Options iaa ie 36 Basic ol nasa din ube tase deta 38 Setting up a Wireless Guest Network ccccccoo 38 WO ts 41 Online Gaming iii 42 Status Monitorina sida 44 Why Monitor Status cocoonocconiioio inca rara 44 Monitoring ADSL Status cooooccccccnnncccccccnnoccccccnnananicnnnnnns 44 Advanced X7N Setup Options commoccccnncccncccnnnnnnnnnnannnnos 46 Viewing the Advanced Setup Options oooocccccccncccccccos 47
77. ot prompted for a User Name and Password do the following in this order Recheck all connections restart the modem and computer and reset the modem by pressing the RESET button on the modem s back panel for 7 seconds Important For security you may want to choose your own X7N password after the setup is complete See Changing User Names and Passwords on page 69 Tip If you configured the X7N using a notebook computer you can keep it plugged in or you can disconnect it from the unit s ETHERNET port As long as the X7N remains plugged into an ADSL wall jack and a power source the X7N can function as a stand alone device You can then make the notebook part of your wireless network Chapter 1 Installation Instructions X7N User Manual Setting Up a Network Once a computer that is directly connected to the X7N modem is able to browse the Internet you know for certain that your ADSL Internet connection is working Now you can set up the rest of your network It is up to you whether you want to have some computers connected directly to the X7N and others connected wirelessly The X7N supports both wired and wireless connections You can have up to 253 connections four of which can be wired directly through the X7N s four ETHERNET ports You can also plug a network device such as a hub switch router or Homeplug adapter into one of the ETHERNET ports To set up your network you can do any or all of the followin
78. ould include TCP IP in it but not AOL Dial up or Adapter and click the Properties button 2 Ensure the following is selected depending on whether you are using dynamic DHCP or static IP addressing e Ifyou are using DHCP most users Ensure that Obtain an IP address automatically is selected and Appendix D TCP IP Network Settings 93 that either Obtain a DNS server address automatically ot Enable DNS is selected All fields should be blank If you are using a static IP address Ensure that Use the following IP address and Use the following DNS setver addresses are selected and that the correct IP address Subnet mask Default gateway and Preferred DNS server values appeat Windows 2000 1 Open the Internet Protocol TCP IP Properties dialog box a From the desktop click the Start button point to Settings then Network and Dial up Connections Right click the Local Area Connection icon and select Properties Select your NIC card s TCP IP entry it should include TCP IP in it but not AOL Dial up or Adapter and click the Properties button Ensure the following is selected depending on whether you are using dynamic DHCP or static IP addressing If you are using DHCP most users Ensure that Obtain an IP address automatically is selected and that either Obtain a DNS server address automatically ot Enable DNS is selected All fields should be
79. our computer either click Control Panel or click Settings and then Control Panel In the Control Panel double click the Internet Options icon If this icon does not appear double click the Network and Internet Options icon and then double click the Internet Options icon 2 On the Internet Properties dialog box select the Connections tab then click the Setup button Appendix E Configuring Your Web Browser 99 3 The setup process will proceed differently depending on your operating system The following table details the process for your Windows computer Note If you are using Windows 7 you do not need to do anything since it will be configured automatically Windows XP a On the Welcome to the New Connection Wizard dialog box click Next If you see a Location Information dialog box click Cancel and then when asked if you are sure you want to cancel click Yes to return to the Welcome dialog box b On the Network Connection Type dialog box select Connect to the Internet then click Next c Onthe Getting Ready dialog box select Set up my connection manually then click Next d On the Internet Connection dialog box select Connect using a broadband connection that is always on then click Next e Onthe Completing the New Connection Wizard dialog box click Finish Windows 98 Me 2000 a On the Internet Connection Wizard dialog box select want to set up my Internet connection manua
80. phone or if there is an existing filter you should replace 1t Try turning your computer off and then on This ensures that your computer gets a correct IP address from the X7N Check your modem s DSL light o If the light is blinking then the X7N was unable to make a DSL connection Go to My X7N s DSL light continually blinks and does not stay solidly lit o Ifthe DSL Light is solid go to My X7N s DSL light is solidly lit but I cannot connect to the Internet Problem My X7N s DSL light continually blinks and does not stay solidly lit Solution There are several issues that could cause this problem Check these items Ensure that the phone cord is firmly plugged into the wall jack and the DSL jack on the back of the X7N Verify that the jack the phone jack your X7N is connected to is enabled for ADSL service Unless your service provider has enabled it you cannot use a standard telephone jack for ADSL service Your phone cord may be defective Replace the phone cord with a known good one If your DSL modem is installed onto the same phone jack as a DSL filter the filter may be defective Please remove the filter from the line and plug the DSL modem into the phone jack If this solves the problem replace the defective filter Appendix A Troubleshooting Tips X7N User Manual e Verify that none of the phones are in use when testing the X7N If the problem appears only when you ate using your phone than yo
81. pone Tobag 35 PPPoA VC MUX Turkey 1 35 PPPoE LLC Turkey 2 35 PPPoA VC MUX United Kingdom 1 38 PPPoA VC MUX United Kingdom 2 38 PPPoE LLC ra 38 PPPoE VC MUX ee te 50 PPPoA LLC Venezuela CANTV 33 1483 Routed IP LLC Vietnam 35 PPPoE LLC Vietnam VDC 35 PPPoE LLC Vietnam Viettel 35 PPPoE LLC Vietnam FPT 33 PPPoE LLC Appendix B ADSL Internet Settings Tables 87 Appendix C Top and Back Panels The following table describes each light on the top panel Light Power DSL Internet Ethernet 1 4 WLAN Description Lights when the X7N is plugged into a power soutce and the Power button on the X7N rear panel is pushed in Blinks when the X7N is performing its startup sequence Stays on solid when the unit has synched up with its ADSL connection Note If the light fails to switch from blinking to steady after a minute or two check with your ADSL provider that the ADSL connection is activated or refer to Appendix A Troubleshooting Tips on page 70 Blinks when data is sent and received Lights when the Ethernet port of the X7N is plugged into the Ethernet port of a powered up device Blinks when there is data activity Lights when the Wireless Local Area Network is running and enabled Blinks when data is sent The following table describes each item on the back panel Port DSL Ethernet 1 4 Power RESET Description Jack to connect the modem to the ADSL
82. r a DNS server name To do this follow the instructions below 1 Check the box Use the Following Static DNS IP Address 2 Inthe Primary DNS Server and Secondary DNS Server text boxes enter the IP addresses of the DNS servers that your ISP instructed you to enter 3 Click Save Reboot Using the ADSL Settings Do need to change my ADSL settings Typically you should not change your ADSL settings unless you are instructed to do so by your service provider Or if you are having problems establishing a physical layer connection you may want to change a couple of the settings on the DSL page Click DSL under Advanced Setup from the left side menu of the Zoom Configuration Manager Setting Description BitSwap Enables or disables bit swapping in both upstream and downstream directions If you experience frequent connection drops it may help to change the bit swap settings After you enter the values click Save Apply Click on Advanced Settings only if you want to configure DSL Advanced Settings Most users will not need to do this Enabling or Disabling UPnP Universal Plug and Play UPnP with Internet Gateway Device IGD protocol is installed in X7N units when they are shipped by Zoom This means that other devices plugged into your computer or network for example a gaming application router or stand alone firewall that use UPnP should automatically detect the X7N and make the needed configurations for them to w
83. r wireless network This is the name that all your wireless devices will connect to You can leave the default name Zoom if you wish 5 Then click Security on the left side menu and from the drop down menu for Select SSID select the wireless network name you just assigned in Step 4 6 From the Network Authentication drop down menu select WEP Open or WEP Shared Most devices use WEP Open however some older Apple Macbooks require WEP Shared 7 For Encryption Strength select 128 bit or 64 bit The 128 bit option is more secure but 64 bit may be faster on older devices We recommend setting 64 bit security 8 In the Network Key text box enter a passphrase of your choice 9 Write down this passphrase and put it where you can find it on the bottom of the X7N case for instance 10 Click Save Apply Now you will need to connect all your wireless devices to the X7N See Chapter 4 for details on connecting different wireless devices to your network If you do not need help connecting your wireless devices to your X7N you may choose to continue with gt Chapter 6 to learn about using the X7N with online gaming Chapter 3 Setting Wireless Security X7N User Manual gt Chapter 7 to learn about monitoring your ADSL Status Most users will not need to use status monitoring gt Chapter 8 to learn about the advanced features of the X7N Most users will not need to change advanced features WPS Configuration
84. rd dialog box type the following User Name and Password in lower case then click OK Appendix A Troubleshooting Tips 73 User Name admin Password zoomadsl The User Name and Passwotd entered here are not the same as the user name and password that your Internet service provider may have given you On the left side click Diagnostics to start the diagnostic test In the Test the Connection to your Internet Service Provider box if the Test PPP Server Connection tests passes but the Test Authentication with your ISP test fails then your PPP User Name and Password are wrong If you are having problems remembering your PPP User Name and Password please see the solution to the next troubleshooting problem My DSL connection requires a User Name and Password but I don t know where to find this information on page 75 e Verizon users who ate replacing an existing modem in California Florida or Texas may need to wait 2 hours after unplugging the existing modem for Verizon to release the line befote it is available for use If this applies to you power down your X7N and wait 2 hours before trying to connect again e Verify that your service provider s ADSL connection is functioning properly Place a call to your service provider s customer support department to verify this e Windows users only Verify that the Web browser on the computer on which you installed the software is configured for a network connection this m
85. refox or Chrome and try to connect to a familiar Web address If you connect successfully you are ready to browse the Web Important To add security to your network see Setting Wireless Security on page 19 Chapter 4 Connecting Devices Wirelessly to the X7N X7N User Manual To disconnect from the current network 1 On your wireless device or computer find the wireless network connection option similar to the process of adding your device or computer to the network Click or highlight Zoom Select or click on Disconnect or similarly named button Connecting a Computer with a Wireless adapter to the X7N 1 Go to the computer that is set up with a wireless adapter that you want to add to the network The computer should have software that will let it perform a site search to scan for available wireless networks in your area When the wireless network name you gave your network in Chapter 3 appears or if you did not change the Wireless Network name the default name Zoom should appeat select it as the network you want to use to connect to the Internet e Ifyou secured your wireless network in Chapter 3 you will need to set up wireless security and enter the password Tip For most wireless adapters you will use its wireless configuration manager software and click a Scan button or select a Site Scan Scan Networks or other similarly named tab to do a site search If you need help refer to the documentatio
86. roup and gives a brief description of the settings you can specify 63 Open page This button from Management gt Backup Settings Update Restore Default Management System Log Management SNMP Agent Opens a page that lets you Save your current configuration settings to a file so that they may be restored at a later time Upload your previously saved settings Restore the X7N settings to the factory defaults By default the System Log is disabled View data generated or acquired by routine system communication with other devices This information does not necessarily represent unexpected or improper functioning and is not captured by the system traps that create alarms You can save the system log to a file Access the SNMP configuration page Simple Network Management Protocol SNMP Chapter 9 Management and Diagnostics X7N User Manual Management TR 069 Client Management Internet Time Management gt Passwords Access Control allows a management application to retrieve statistics and status from the SN MP agent in this device Access to a page that allow an Auto Configuration Server ACS to perform auto configuration provision collection and diagnostics to the ADSL modem Select the desired values and click Save to configure the TR 069 client options Access to a page that allows you to set up the X7N to automatically synchronize wit
87. rowser X7N User Manual Configuring Internet Explorer Version 8 0 The following instructions are for Internet Explorer Version 8 0 If you do not have this version you can get a free upgrade from Microsoft Corp If you are not sure what version you have open Internet Explorer and from the Help menu choose About Internet Explorer The version number is directly below the Microsoft Internet Explorer logo You can ignore all the numbers after the period following the first digit Note If you are using Windows 7 you do not need to do anything since it will be configured automatically Internet Explorer can be configured to use a specific connection but by default will use the correct default active connection However if you want to manually setup a different connection 1 On the desktop double click the Internet Explorer icon Tip If you cannot access Internet Explorer in this way open your computer s Control Panel click the Start button and then depending on your computer either click Control Panel or click Settings and then Control Panel In the Control Panel double click the Internet Options icon If this icon does not appear double click the Network and Internet Options icon and then double click the Internet Options icon 2 Once open select Tools gt Internet Options and then click on the Connections tab 3 Select Setup to setup an Internet connection If the wired Ethernet is correctly setup then a popup m
88. s not turn on make sure there is power going to the outlet you are using If the unit still doesn t work contact Zoom Technical Support See Appendix G on page 103 for contact information e If you are using a wireless device try connecting a computer directly to the X7N s Ethernet ports If a computer directly connected to the X7N works then the problem is with your wireless connections See the wireless troubleshooting tip on page 77 e If you cannot access the Internet with a computer directly connected to the X7N s Ethernet port check your Ethernet connection Most computers have a power light next to the Ethernet jack to indicate the Ethernet cable is properly connected Verify that this light is on and that the Ethernet light on the front of the X7N is on If the Ethernet light is off on either the X7N or on the computer verify that the cable is properly pushed in If the light still doesn t turn on you should try another Ethernet cable e Check your phone cable and splitters Replace your phone cable with a tested working phone cable If you have installed a splitter between the X7N and the phone jack remove this splitter If this solves the problem you may need to replace this Appendix A Troubleshooting Tips 71 splitter When testing the X7N make sure that the telephones in your house ate not in use If the problem only exists when a particular phone is in use then you may need to install a filter on that
89. security is enabled otherwise refer to Appendix A Troubleshooting Tips on page 70 In the Successfully connected to desired network dialog box you have three options You can e Select Save the network and Start this connection automatically if you always want to connect to the same network Then click Close The next time you start your computer you will automatically connect to the selected network e Select Save the network and clear the Start this connection automatically check box if you don t want to automatically connect to this network every time you start your computer but you will want to connect in the future Click Close to display the Select a location dialog box where you choose a location Windows Vista automatically applies the correct network security settings If the User Account Control dialog box appears click Continue e Click Close to complete the connection procedure Select this option if you are connecting to this network only one time To disconnect from the current network 1 2 From the Start menu select Connect to In the Disconnect or Connect to another network dialog box select the current network and click Disconnect In the Are You Sure message box click Disconnect again In the next dialog box you can connect to another network or click Close to complete the disconnect procedure 29 Connecting a Windows XP Computer with Built in Wireless Capan rs On your Wi
90. st countries channels 1 13 are normal for private wireless networks The following table shows countries known to use channels other than 1 13 for private wireless networks Country Channels France 10 13 Israel 4 9 Japan 1 13 14 802 11b only Taiwan 1 11 USA 1 11 Appendix F Wireless Channels by Country Appendix G Getting Help Zoom has many Technical Support services available to its customers e To Register Your Product Or Get Assistance We can support you best if you register your product at www zoomtel com register We have many ways to assist you and you can see them at www zoomtel com techsupport From here you can send email to our technical support experts and or do a smart search through our intelligent database by using SmartFacts Tip From time to time Zoom may release improved firmware This is also available at www zoomtel com along with upgrade instructions We recommend that you check our Web site periodically for updates You can reach Technical Support by calling these numbers In the United States call 617 753 0961 In the UK call London 44 2033180660 or Manchester 44 1618840074 e Some retailers of Zoom products provide support or can recommend a convenient support center Appendix G Getting Help Appendix H Regulatory Information 54 Declaration of Conformity ZOOM Declaraci n de conformidad Manufacturer Fabricante Zoom Telephonics Inc
91. stry Canada label identifies certified equipment This certification means that the equipment meets telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing the equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of concern The customer should be awate that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate NOTICE This equipment meets the applicable In
92. t For more information see Resetting Default Settings on page 67 To back up your current configuration Use the Backup page of the Configuration Manager to save your modem s current configuration to a file on your computer 1 Click on the Management link on the left pane of the window Then click on the Settings link Then click on the Backup link 2 On the Backup page click Backup Settings to download a configuration file from the X7N to a folder on your computer 3 Be sure to note the name backupsettings conf and location You will need this information if you ever want to restore the X7N to this backed up configuration You can change the name of the file and specify a location for it on your computer after it is downloaded To restore a configuration 1 Click on the Management link on the left pane of the window in the Configuration Manager 2 Then click on the Settings link 3 Then click on the Update link 4 On the Update Settings page click Browse and navigate to the file containing the configuration to which you want the X7N restored 5 Click Update Settings Resetting Default Settings If you have changed the system settings on your X7N and for some reason want to restore them to the factory default settings 67 you can do so in one of two ways You can perform a software reset or a hard reset To reset using the X7N s Web interface If you can open your Web browser and access your X7N s Config
93. telephone wall jack LAN ports that can connect the unit to access points network hubs or the Ethernet ports of a computer Port to connect the unit to the X7N s power cube In the unlikely event that you need to reset the modem to its system default settings necessary if communication link is lost you can press the RESET button for 7 seconds Appendix C Top and Back Panels X7N User Manual WPS Press the WPS button on your Router and hold it in for two 2 seconds until the Wireless LED starts blinking rapidly Click or press the WPS button on the client device This button may be a physical button on the unit or a software button in its application Refer to your client device s documentation for further instructions if necessary ON OFF Button when pressed once turns the modem s power ON When pressed again turns the modem s power OFF Appendix C Top and Back Panels 89 Appendix D TCP IP Network Settings If you are using a Mac computer you must ensure that your computer s TCP IP network settings are configured properly Otherwise you will not be able to connect to the Internet Note If you are using a Windows computer you do not have to configure the TCP IP settings if you are using DHCP because your Windows computer will automatically configure them for you If you are not using DHCP you will need to set up the TCP IP settings for your Windows computer Windows users who are troubleshooting the
94. tes to use a computer or other electronic device to send any message via a telephone facsimile unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the date and time it is sent and an identification of the business other entity or individual sending the message and the telephone number of the sending machine or of such business other entity or individual The telephone number provided may not be a 900 number or any other number for which charges exceed local or long distance transmission charges Telephone facsimile machines manufactured on and after December 20 1992 must clearly mark such identifying information on each transmitted message Facsimile modem boards manufactured on and after December 13 1995 must comply with the requirements of this section This equipment cannot be used on public coin phone service provided by the telephone company If trouble is experienced with this equipment for repair or warranty information please contact Zoom Telephonics Inc 207 South Street Boston MA 02111 USA 617 753 0961 If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved Connection to Party Line Service is subject to state tariffs Contact your state public utility commission public service commission or corporation commission for more information If
95. the default name Zoom and click Connect e Ifyou enabled security in Chapter 3 in the next dialog box enter the security key or password and click Connect e If your desired network is unsecured in the message box select Connect Anyway Note We strongly recommend that you set up a secured network For information on wireless security see Setting Wireless Security on page 19 gt When you click on the wireless network option box Windows will scan for available networks More than one wireless network may appear in the list These are other wireless networks that are within range of your network Your neighbors for instance may be within range of your network Each wireless network has a channel associated with it We recommend there be at least a five channel difference between your network and those of your neighbors Having less than a five channel difference may result in interference with your connection By default the X7N uses channel 10 If you need to change this channel Chapter 4 Connecting Devices Wirelessly to the X7N X7N User Manual you must do so using the Wireless Setup page of the Zoom Configuration Manager For instructions on how to log in to the Zoom Configuration Manager see page 14 After logging in select Wireless from the left side menu On the Wireless page you can select a new channel from the drop down menu If you have difficulty connecting make sure you have entered the correct password if
96. the power adapter into a wall outlet or power strip 3 Press the Power button on the back panel of your X7N to power ON the modem 4 Connect an Ethernet cable between any one of the X7N s ETHERNET ports and any of the computer s or other device s Ethernet ports Then turn on the computer or game station One Ethernet LED on your modem s top panel should turn on X7N Back Panel Diagram lors ANTENNA DSL ETH 4 ETH3 ETH2 ETH1 POWER RESET WPS ON OFF ANTENNA 5 Connect the supplied phone cord between your modem s DSL jack and a phone jack with ADSL service Note Many X7N models include a filter splitter This can be used if you want to use a phone near the modem A filter splitter or ADSL filter should also be used with phones Chapter 1 Installation Instructions X7N User Manual not located near the modem to prevent interference between the modem and phone when the phone is off hook To use a filter splitter with a modem and a phone connect the filter splitter s LINE or PHONE LINE jack to a phone jack in the wall plug the supplied phone cord between your modem s DSL jack and the filter splitter s MODEM jack and plug the phone into the filter splitter s PHONE jack Some but not all filter splitters require you to use a short phone cord to connect the filter splitter to a phone jack in the wall Note that the filter splitter is NOT required if you simply want to plug your modem into a phone jack in th
97. tion This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483 5 MHz For detailed information the end user should contact the national spectrum authority in France 0 6 7 8 O lle esky Zoom Telephonics Inc timto prohlasuje ze tento Zoom ADSL Czech Modem Router w Wireless N je ve shod se z kladn mi pozadavky a dal mi p slu n mi ustanoven mi sm rnice 1999 5 ES Dansk Undertegnede Zoom Telephonics Inc erkl rer herved at f lgende Danish udstyr Zoom ADSL Modem Router w Wireless N overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Deutsch Hiermit erkl rt Zoom Telephonics Inc dass sich das Ger t Zoom German ADSL Modem Router w Wireless N in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999 5 EG befindet let rest K esolevaga kinnitab Zoom Telephonics Inc seadme Zoom ADSL Estonian Modem Router w Wireless N vastavust direktiivi 1999 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele enlEngish Hereby Zoom Telephonics Inc declares that this Zoom ADSL Modem Router w Wireless N is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC es Espa ol Por medio de la presente Zoom T
98. to put in your own DNS To create mapping groups with appropriate LAN and WAN interfaces to set up groups that perform as independent networks utilizing multiple ports to PVC and bridging groups To add edit or remove IPSec tunnel mode connections Local To add view or remove local certificates used by peers to verify your 49 identity A maximum of 4 certificates can be stored Trusted CA Certificate Authority Add view or remove CA certificates used by you to verify peers certificates A maximum of 4 certificates can be stored Multicast Sets up IGMP protocol Most users will only do this if instructed by their service provider Changing Your WAN Settings The WAN Configuration page of the X7N Configuration Manager is used to change the advanced settings of your Wide Area Network WAN connection Most users should use the Basic Setup to edit their WAN connection To open this page click Basic Setup on the left side menu To Edit a Previous Configuration If you already created a configuration from the Basic Setup page ot from the WAN page at an earlier time you can click Edit to make changes to that configuration Then use the Next and Back buttons to navigate through a series of pages where you can make changes to advanced parameters such as the ATM Traffic Class and Encapsulation Mode and enabling NAT settings IGMP Multicast and WAN Service To Add a New Configuration If you want to add a n
99. u either need to install a filter on that phone or if there is an existing filter you should replace it with a known working one e You may be having an issue with the phone wiring inside your house Try plugging the X7N into different phone jacks to see if that solves the problem If you know where your phone line enters your house often called the Demarc Point and is typically a gray box found either in your basement your garage or on the outside of the house and you have easy access to the Demarc Point try plugging your X7N at this point If this solves your problem you may need a professional to repair your inside phone wiring Problem My X7N s DSL light is solidly lit but I cannot connect to the Internet Solution There are several issues that could cause this problem Check these items e Ensure that you are using the correct VPI VCI and Encapsulation settings If you don t know what they are please refer to the ADSL Settings Table in Appendix B e If your Encapsulation begins with PPP ensure that you have typed your ADSL User Name and Password correctly Note that this is NOT the User Name and Password you used to log into the Zoom Configuration Manager on page 14 To verify that your PPP User Name and Password are correct login into the configuration manager Open the Zoom Configuration Manager by entering the following in your Web browser s address bar http 192 168 1 1 In the Enter Network Passwo
100. unning the autodetect If you are having problems establishing your DSL connection see the My X7N s DSL light continually blinks and does not stay solidly lit tip on page 72 You are trying to detect a static IP connection Autodetect only works with connections that use DHCP Typically you have to request and pay extra for a static IP connection If you know this applies to you then you must configure your connection manually See Chapter 1 for more information on configuring your connection manually Appendix A Troubleshooting Tips X7N User Manual Autodetect may not be able to detect your connection In this case you may need to manually configure your connection See Chapter 1 for configuring your connection manually Problem My computer devices are not connecting wirelessly to the X7N Solution Try the following Check your wireless security settings on your X7N and verify that your device is using the same settings Check the signal strength of your wireless connection Most wireless adapters have some type of signal strength meter that shows how strong your wireless signal is Windows users click the Wireless icon in your system tray to check signal strength If your signal strength is not strong enough try the following gt Reorient the receiving antenna on your X7N gt Move the X7N to another atea gt Move the device trying to access the X7N to a different location ideally closer to the X7N Cha
101. ur wireless adapter or setting its mode refer to the documentation that came with it After you install the adapter see the instructions on page 30 for Connecting a Computer with a wireless adapter to the X7N Connecting a Windows 7 Computer with Built in Wireless Capabilities 1 From the taskbar click on the wireless symbol 12 47 PM a E 7 15 2011 2 In the wireless network options box highlight the name you gave your wireless network in Chapter 3 If you did not change the Wireless Network name select the default name Zoom and click Connect If you wish to connect automatically to this network ensure that the Connect Automatically box is checked Chapter 4 Connecting Devices Wirelessly to the X7N X7N User Manual Not connected t E il Connections are available Wireless Network Connection Tendax7nyimin MDAWIFI zoomdvtlab MediaSilo T1 al Credo wt Credo guest MediaSilo Guest Access ai _ 7 Open Network and Sharing Center 12 47 PM i B CAD k 7 15 2011 If you enabled security in Chapter 3 in the next dialog box enter the security key or password and click Connect If your desired network is unsecured in the message box select Connect Anyway Note We strongly recommend that you set up a secured network For information on wireless security see Setting Wireless Security on page 19 gt When you click on the wireless network option box Windows will scan for available
102. uration Manager do the following to perform a softwate reset 1 Log into the Zoom Configuration Manager See page 14 if you need help logging in 2 Click on the Management link on the left pane of the window Then click on the Settings link Then click on the Restore Default link 3 Click the Restore Default Settings button To perform a hard reset If you lose your link to the unit and cannot communicate with it via the Web browser do the following to perform a hard reset Press the RESET button on the modem s back panel for seven seconds You are now guaranteed that all system settings are restored to the X7N s factory defaults Remote Access to Your Modem Configuration Settings If you want to be able to access your modem Configuration Manager to change or view your configuration settings remotely 1 Click on Management Click on Access Control then click on Services and select the enable check box for Http WAN to allow access from a remote PC Click Save Apply and wait several seconds for the settings to be saved 2 Click on Status from the left pane of the Zoom Configuration Manager Click on WAN Write down the public IP address displayed under WAN Info Chapter 9 Management and Diagnostics X7N User Manual 3 Type this public IP address into the browser of your remote PC 4 At the log in prompt enter the User Name and Password shown below User Name support Password support 5 You can now view or
103. ure the WDS Wireless Distribution System feature of the wireless LAN interface Configure the advanced features of the witeless LAN interface Most users do not need to change these settings Shows authenticated wireless clients and their status 37 Basic Setup The table below explains the Wireless Basic settings This setting Enable Wireless Channel SSID Wireless Network Name BSSID Broadcast SSID Country Max Clients Hide SSID Client Isolation Lets you specify A check mark in the Enable Wireless check box shows that your wireless network is up If there is no check mark next to the Enable Wireless check box the X7N s Wireless capability is not enabled Indicates the channel your wireless connection uses by default for your wireless connection The X7N comes set for channel 10 The Service Set Identifier for your wireless network By default the SSID for the X7N is Zoom You can change the SSID to any name that you want Shows the Wireless MAC address of your X7N Select your country from the drop down menu Up to 16 wireless clients are allowed on each network Click in the check box if you do not want to broadcast the SSID of your network Enabling client isolation will prevent wireless clients on the same network from communicating with each other Typically this feature is used in public hotspots or corporate environments Setting up a Wireless Guest Network
104. urrent password in the textbox Old password 3 Choose the password you would like to replace it with up to 16 characters without any spaces and enter it in the textbox New password 4 Retype the password in the textbox Confirm password 5 Click on Save Apply TR 069 The TR 069 option of the X7N Configuration Manager opens a page where you can allow an Access Control Server ACS to control and configure your X7N This feature must be supported by your service provider and should be enabled by you only if the provider instructs you to enable it 1 Click Management from the left side menu of the Zoom Configuration Manager 2 Then click TR 069 Client 3 After you make changes on the TR 069 client config page click Save Diagnostics You can use the Diagnostics page of the Configuration Manager to run a series of diagnostic tests of your system software and hardware connections Chapter 9 Management and Diagnostics X7N User Manual Appendix A Troubleshooting Tips The following ate some problems you may experience and some g p y y exp possible solutions to remedy the situation Problem I am unable to connect to the Internet Solution There are several issues that could cause this problem Check these items e Verify that the PWR light on the modem is on If it is off check that the modem is plugged into a wall outlet and that the POWER button on the back of the modem is pushed in If the light doe
105. usten ja sit koskevien direktiivin Appendix H Regulatory Information muiden ehtojen mukainen sel svenska H rmed intygar Zoom Telephonics Inc att denna Zoom ADSL Swedish Modem Router w Wireless N star I 6verensstammelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 1 m G Compliance Model Identification Model name Product name Zoom ADSL SERIES 1093 MODEL MODEM Router 5790XY WHERE w Wireless N X A B C D E F OR NOTHING AND Y G H J K L M OR NOTHING IC Zoom ADSL Series 1093 Model 5790 003 MODEM Router w Wireless N CE0678 Zoom ADSL Series 1093 w Wireless N FCC ID BDN1093WL ICID 1535A 1093 3121 B 27659 2011

Zoom ADSL X7N ADSL2+ Wi-Fi Ethernet LAN Black

Contents

Download Pdf Manuals

Related Search

Related Contents