Technoline WS 6815 weather station
Contents
1. ADAPTOR JACK INSERT 1 x CR2032 BATTERY INSIDE THE BATTERY COMPARTMENT OUTDOOR TEMPERTAURE SENSOR P 2 ENVIRONMENTAL RECEPTION EFFECTS Your radio controlled clock obtains the accurate time with wireless technology Same as all wireless devices the receiving ability maybe affected by but not limited to the following circumstances Long transmitting distance Nearby mountains and valleys Among tall buildings Near railway high voltage cable etc Near freeway airport etc Near construction site Inside concrete buildings Near electrical appliances Near computers and TV s Inside moving vehicles Near metallic structures Place your clock at a location with optimal signal i e close to a window and away from metal surfaces or electrical appliances QUICK SETUP Step 1 Keep your weather station and wireless sensor next to each other Slide open the battery cover at the back of your wireless outdoor sensor make sure the channel selector is set at position 1 top position then insert 2 x AAA batteries not included into the outdoor sensor by observing the correct polarity signs inside the battery compartment Replace the battery door Step 2 Insert the AC DC adaptor to any 230V AC household outlet Then insert the DC jack to the back case of your weather station Step 3 Slide open the battery cover at the back of your clock then insert 1 x CR2032 Lithium battery not included to the battery compart2. button of the weather station then press the RESET button located on the back of the outdoor transmitter If you continue to lose the outdoor temperature display try placing the transmitter in a different location until you have smooth transmission of temperature data DIMMER FUNCTION Press SNOOZE DIMMER once to adjust the high low brightness of the display TROUBLE SHOOTING In case your clock shows irrelevant information or digits it maybe affected by electrostatic discharge or interferences from other devices Press the RESET button on the back of your clock Your clock will be reset to default setting of time and calendar and it will start to receive radio controlled time signal again CARE OF YOUR RADIO CONTROLLED CLOCK Do not expose the unit to extreme temperature water or direct sunlight Avoid contact with any corrosive materials Do not subject the unit to excessive force dust or humidity Do not open the inner back case or tamper with any components of this unit EON SPECIFICATIONS Operation temperature 0 C to 45 C Temperature measuring range Indoor 14 to 122 10 C to 50 C display shows HH H LL L if out of this range Outdoor 58 F to 158 F 50 C to 70 C display shows HH H LL L if out of this range Temperature resolution 1 C Humidity resolution 1 Alarm duration 2 minutes Snooze duration 5 minutes P 6
3. 60 minutes 4 Press SET to return to normal mode or it will return to normal mode in around 8 seconds if no further press of any other buttons 5 Your clock is in 24 hour display format TO SET ALARM default alarm setting is 6 00 AM 1 Press and hold ALM the hour digits flash with AL icon flashing Press V A your desired alarm hours 2 Press ALM once again the minute digits flash Press Vv toset your desired alarm minutes 3 Press ALM once to store your alarm setting and return to normal time display or the clock will return to normal mode in around 8 seconds if no further press of any other buttons To turn ON or OFF the alarm Single press ALM one at a time to turn on or off the alarm When the alarm function is turned the AL icon appears on top of the time digits To use the snooze function When time reaches your set alarm time your clock will give a beep sound to wake you up The AL icon will flash 1 Press SNOOZE once to stop the alarm temporarily AL icon keeps flashing The alarm will beep again in 5 minutes or after your set snooze duration 2 To stop the daily alarm press any button except the snooze when alarm is beeping The alarm will stop and AL icon becomes static alarm will beep again same time next day Alarm Duration 2 minutes If you lose the outdoor temperature When the outdoor temperature digits show the wireless transmission is either interrupted or lost Press amp hold
4. INSTRUCTION MANUAL OF WS6815 RADIO CONTROLLED LED ALARM CLOCK WITH INDOOR AND OUTDOOR TEMPERATURE INDOOR TEMPERATURE TIME ALARM ON OUTDOOR TEMPERATURE Wy Sy Gy 45 qf 1 RCC INDICATOR STAND SNOOZE DIMMER 2 SNOOZE DIMMER BATTERY DOOR UP ALARM SET DOWM WAVE RESET DESIGN BY NEXUS INSERT 1 x CR2032 BATTERY INSIDE THE AC DC ADAPTOR BATTERY COMPARTMENT D 77 DC SOCKET a INSERT AC DC b ADAPTOR JACK LED Battery 2 x 1 5V AAA CHANNEL 1 Z CE ECE 2 DESIGN BY NEXUS J DESIGN BY NEXUS CHANNEL 3 Ky joo ie Dl RESET a INSERT 2 x AAA Pali a BATTERIES alll LMI Ie amp STAND amp OUTDOOR TEMPERAURE SENSOR Words in the figure cer 2 2227
5. ment Make sure polarity of the battery is facing up Then replace the battery cover Your weather station will receive data signal from the outdoor sensor in few seconds Then place your outdoor sensor in a dry and shaded area outdoor DCF SIGNAL RECEPTION AND SIGNAL INDICATOR After your clock is powered up it starts to receive DCF signal The icon flashes Receiving DCF signal A icon flashing Successful reception 2 icon becomes static Failed reception icon disappear During reception press WAVE once will display reception mode and signal strength indication When strong DCF signal is detected display shows with 3 bars ie iy Te When weak or no DCF signal is detected display shows P 3 During reception the signal strength may move from 1 bar to 2 bars to 3 bars This is normal since the clock is detecting DCF signal and other signals in the air at the same time Press SET will return A to the time display with 2 icon flashing Successful reception or failed reception icon becomes static on stop blinking when reception is successful _ icon disappears when reception is failed Automatic reception and manual reception Your clock starts automatic reception everyday at 1 00 2 00 and 3 00 If it fails to receive the DCF time signal at 3 00 it will start reception at 4 00 If it fails again it will start reception at 5 00 If it fails again i
6. t will start automatic reception at 1 00 again in the next day For manual reception simply press and hold V WAVE your clock will gives a short beep and starts manual reception Press and hold WAVE to stop DCF reception During RCC reception all buttons do not function and it does not take temperature and humidity measurement The temperature and relative humidity readings will get stable and become more accurate after your weather station clock is powered up for around 30 minutes To cancel DCF reception permanently Press and hold W WAVE and at the same time for 2 seconds your clock will give 2 short beeps and the radio controlled function is permanently disabled To resume the radio controlled function press and hold V WAVE and A at the same time for 2 seconds your clock will give 2 short beeps and will start DCF immediately Note Keep in mind that your outdoor transmitter has a 30 meter open air transmission with no obstructions Actual transmission range will vary depending on what is in the path of the signal Each obstruction roof walls floors ceilings thick trees etc will effectively cut signal range in half TO SET TIME 1 Press and hold SET for 2 seconds hour digits flash Press to set hours 2 Then press SET once again the minute digits flash Press A button to set minutes 3 Then press SET once again display shows 05 and flash Press button to set snooze duration from 5 minutes to
Download Pdf Manuals
Related Search