AMX NXA-SMT43X
Contents
1. use the appropriate mounting holes in the back of the surface mount box to insert 2 or more mounting screws not supplied The hole pattern in the surface mount box and mounting plate will fit many single and double gang conduit boxes NOTE Do not over tighten the mounting screws The corner tabs on the surface mount box must NOT penetrate the mounting surface Assembling the Side Conduit Knockout Cover 1 If not using a side conduit for the Ethernet connection assemble the side conduit knockout cover by placing the 3 locating tabs on the knockout cover into the 3 slots on the surface mount box and secure with the supplied screw FIG 3 FIG 3 Side conduit knockout detail NOTE Do not over tighten the screw as this can bend the side conduit knockout cover Installing the NXD 430 435 Display Into the NXA SMT43X 1 Pull enough Ethernet cable through the wall or conduit to allow a connection to the touch panel Connect the Ethernet cable to the touch panel display NOTE Do NOT apply power at this time 2 The interior of the surface mount box has two slots in the top FIG 4 Insert the two tabs at the top of the touch panel display into those slots and pivot the bottom of the display into the surface mount box e mount slots Torx head screws _ gt FIG 6 Attaching the cover to the surface mount box NXA SMT43X Wall Cover Plate The NXA SMT43X wall cover plate 53 2266 02 is a disposable cover2. mount box and secure it with the two included 8 screws 80 0146 02 FIG 7 3 When ready to install the touch panel remove the wall cover plate FIG 8 and install the rest of the NXA SMT43X as necessary Assembly slot for snaps on bezel FIG 5 Attaching the bezel to the touch panel display Attaching the Cover to the Surface Mount Box 1 Slide the cover over the front of the surface mount box FIG 6 Make sure that the slot for the side conduit knockout is on the right bottom of the cover as it faces toward you 2 Insert the 2 supplied painted white Torx head screws into the screw holes at the bottom of the cover and tighten ae 8 NXA SMT43X with 3 Connect the Ethernet to the Master and verify that the touch panel receives power and Pe j S R aE al Cover plate data For full warranty information refer to the AMX Instruction Manual s associated with your Product s 93 2262 16 REV A 2011 AMX All rights reserved AMX and ae logo are registered trademarks of AMX I CN AMX reserves the right to alter specifications without notice at any time A bang 3000 RESEARCH DRIVE RICHARDSON TX 75082 e 800 222 0193 e fax 469 624 7153 technical support 800 932 6993 e www amx com af EA
3. shipped with the NXA SMT43X In situations where the NXA SMT43xX box is installed before the touch panel assembly the cover protects the interior of the box from falling dust When the touch panel is installed the cover should be removed and disposed of in an environmentally friendly u R gt UN manner AY To install the wall cover plate Screws gt py N 1 Install the mounting plate and surface mount box to the wall FIG 2 FIG 4 Inserting the NXD 430 435 display into the NXA SMT43X Surface Mount Box 3 At the bottom of the display are two screw holes Insert the two included cap screws into the holes and carefully tighten Do not use excessive torque on these screws as this may damage the display circuit board f 8 screw Attaching the Bezel to the Touch Panel Display When installing an NXD 430 435 into an NXA SMT43X the front bezel is installed differently than in a typical installation l 1 With an NXD 435 carefully connect the ribbon cable from the touch panel display to the bezel 2 Attach the bezel to the surface mount box by placing the assembly tabs on top of the surface mount box into the pockets on the top of the bezel FIG 5 3 Press the lower portion of the bezel toward the display until it snaps into place Assembly tabs Ty 8 screw a NXA SMT43X 7 Wall Cover Plate FIG 7 Installing the NXA SMT43xX wall cover plate to the surface mount box 2 Slide the wall cover plate over the surface
4. an EFA Overview The NXA SMT43X NXD 430 435 Surface Mount Box FG2262 16 allows the installation of NXD 430 and NXD 435 panels in existing structures and in locations where a flush installation is not possible The NXA SMT43X FIG 1 is comprised of four components the mounting plate the surface mount box the side conduit knockout cover and the cover as well as an optional wall cover plate Touch panel front bezel Side conduit knockout cover FIG 1 NXA SMT43X NXD 430 435 Surface Mount Box Product Specifications NXA SMT43X Specifications Dimensions HWD e 41 4 x 5 3 4 x 3 1 8 108 mm x 147 mm x 79 mm Weight 1 80 Ibs 0 82 Kg Operating Environment e 32 104 F 0 40 C Max relative humidity 85 non condensing Certifications e UL Listed Included Accessories e Screw 4 40 x 250 4 80 0110 e Screw 8 32 x 50 2 80 0146 02 e Washer 4 Split 2 80 0310 e Screw 4 40 x 250 Torx Flat Head White 2 80 5966 04 e NXA SMT43X Wall Cover Plate 53 2266 02 Other AMX Equipment e NXD 430 BL Black 4 3 Modero Wall Flush Mount Touch Panel FG2262 01 e NXD 430 WH White 4 3 Modero Wall Flush Mount Touch Panel FG2262 02 e NXD 435 BL Black 4 3 Modero Wall Flush Mount Touch Panel FG2262 03 e NXD 435 WH White 4 3 Modero Wall Flush Mount Touch Panel FG2262 04 UL Type 1 Installation Requirements e Use in clean and dry mechanical rooms e Cover during the construct
5. emove the protective backing from the adhesive on the mounting plate and attach the mounting plate to the wall Do NOT attempt to remove and reposition the mounting plate as this may damage both the adhesive and the wall 1 If the NXA SMT43X is to be mounted to drywall and you would like additional screws for a more secure mounting use the holes on the mounting plate FIG 2 to mark locations for plastic screw inserts and install them at this time Mounting screws and inserts are not supplied Any combination of holes may be used to secure the mounting plate to the wall but do NOT use the four corner pin slots at each corner of the mounting plate 2 Use at least 2 mounting screws not supplied to secure the mounting plate to the wall Installing the Surface Mount Box to the Mounting Plate 1 If connecting Ethernet cable to the touch panel through the wall remove the rear knockout FIG 2 at this time If connecting Ethernet cable via a conduit remove the side knockout Corner tabs MUST NOT penetrate mounting surface Side knockout Surface mount box Washers FIG 2 Attaching the surface mount box to the mounting plate 2 Attach the surface mount box to the mounting plate using the corner pin slots on the mounting plate 3 Secure the bottom mounting plate to the surface mount box with two assembly screws Put one split washer between the screw head and the mounting plate FIG 2 4 For additional security
6. ion phase to ensure equipment does not get infiltrated with construction dust e Use in environments that do not exceed 95 non condensing humidity Preparing the NXD 430 435 for Installation When shipped the NXD 430 or NXD 435 touch panel to be installed into the NXA SMT43X is assembled with a front bezel and back box For more information please refer to the NXD 430 435 Operation Reference Guide available at www amx com Both the bezel and back box must be removed before the panel display can be installed To prepare the NXD430 435 for installation 1 Lift up on the bezel to detach the front bezel 2 With an NXD 435 carefully disconnect the bezel from the ribbon connector on the touch panel 3 Remove the two screws at the bottom of the display FIG 4 to disconnect the display from the back box These are plastic screws and cannot be reused 4 From the bottom swing the display out and then down to release it from the two retention prongs at the top of the display Assembling the NXA SMT43X The NXA SMT43X has been designed to fit US domestic and a variety of international conduit wall boxes Use the appropriate holes in the pattern provided for mounting If mounting to a conduit wall box remove the rear conduit knock out and assemble the mounting plate to the surface mount box with the two screws provided on the bottom of the unit The backing plate may be omitted if mounting the NXA SMT43X to a conduit box but is recomme
7. nded to help maintain proper spacing from the wall Before starting assembly of the NXA SMT43xX select its installation location For power and data this site needs access to an Ethernet connection either through the wall itself or via a conduit If the Ethernet cable can be run through a wall the rear knockout on the surface mount may be removed and the cable run through the rear knockout and the mounting plate If the Ethernet cable needs to be installed through a conduit the side conduit knockout may be removed and the conduit connected to the side of the surface mount box Installation Guide NXA S MT43X NXD 430 435 Surface Mount Box For added security it is recommend that additional screws be used if the device is surface mounted with no conduit box Prior to placing the mounting plate on the mounting surface use the mounting plate to mark 2 to 4 screw locations using these locations install appropriate screw inserts After the screw inserts have been installed remove the protective adhesive backing from the mounting plate and apply plate to the chosen surface Make sure that the plate is square and level and lined up with the screw hole locations Remove the appropriate conduit knockout on the surface mount box at this time Attach the surface mount box to the mounting plate using the 4 key way slotted holes and two 4 40 cap head screws supplied Installing the Mounting Plate Adhesive and Screws 1 For additional strength r
Download Pdf Manuals
Related Search