Anthro eNook Standard
Contents
1. 325 3841 or visit anthro com We re happy to walk you through the assembly ANTHRO Technology Furniture Fast and Friendly Anthro Corporation 10450 SW Manhasset Dr Tualatin OR 97062 Toll free 800 325 3841 Fax 800 325 0045 email sales anthro com anthro com Outside the U S Tel 503 691 2556 Fax 503 691 2409 300 5394 00 Warranty eNook has a five year warranty Notices Technology Furniture and eNook are trademarks of Anthro Corporation Patent Pending Anthro reserves the right to modify the design and specifications without prior notice2. 0 3 8 Screw 1 325 5172 00 A Cable Clips 6 175 5217 00 Toggle Bolt Dry Wall Anchor 4 325 5394 00 1 5 8 Screws 4 325 5086 00 08 o9 Anthro Hex Driver not shown 1 375 5000 00 0 Cross Tra 1 225 2408 23 10 y E Main Unit 1 835 5200 xx 11 IPA Pinch Cover 2 225 2418 23 12 Ik Tack Board 1 100 6603 xx 13 Tack Clip 1 225 2424 23 STEP 1 Select the Mounting Location When choosing the right place to install your eNook be sure to check the location of your power source The power cord that comes with your eNook is 6 ft long m Your eNook can be mounted to drywall or to wood wall studs If you re installing to wood wall studs go to Step 2 If you re installing into drywall go to Step 7 STEP 2 Find Wall Studs Using a stud finder locate the studs to which you ll attach your eNook STEP 3 Determine Mounting Point Determine the optimal desk height for your eNook Typical sitting height is about 29 high typical standing height is about 42 high 14 75 23 m Measure up 14 3 4 from the shelf height and mark that point on one stud ie STE P4 Wall Stud Profile Attach Screws to Wall Studs m Using a 1 8 drill bit drill one hole in a stud about 1 1 2 deep How do you make sure that hole is 1 1 2 deep Measure that length on your drill bit and mark it with a piece of masking tape Stop drilling when you reach the masking tape m Using a Phillips driver or a po
3. ASSEMBLY INSTRUCTIONS eNook II Part Number EK3616zz xx NOTE The eNook additional shelves shown above are not included ANTHRO Technology Furniture Fast and Friendly Anthro Corporation 10450 SW Manhasset Dr Tualatin OR 97062 Toll free 800 325 3841 Fax 800 325 0045 email sales anthro com anthro com Outside the U S Tel 503 691 2556 Fax 503 691 2409 January 2007 108 WELCOME PARTS LIST Thank you for purchasing eNook These instructions are for Anthro s eNook Before beginning an a assembly please take a moment to review the parts list below This installation is a two person job to verify that your shipment is complete If you have any questions or if we The following tools are required but not included can help you in any way please m Power Drill contact us at 800 325 3841 m 1 8 drill bit for mounting to wood wall studs NOTE We provide do it yourself m 1 2 drill bit for mounting to drywall j m Phillips screwdriver or Phillips bit for your drill hardware and instructions for m ieee installation to wood studs and dry F sail Your eNook can be mounted Stud Finder for mounting to drywall l i Product Quantity Part Number to other surfaces like concrete EE eS ae and brick and this work should be eNook Wall Frame 1 223 2RAT 23 done by a qualified contractor 6 Outlet Surge Protector 1 400 5190 06 1 5 Screws 4 325 5358 00 Workstation Screws 4 325 5092 0
4. s the upper mounting height Once you determine the right height for your eNook mark one mounting point hole location When choosing the first mounting point remember that the two upper mounting points should be at least 16 apart to keep the eNook stable To help you visualize where eNook will be on your wall use the eNook Frame as a template 14 75 7 4 Questions Call us at 800 325 3841 or visit anthro com We re happy to walk you through the assembly STEP 8 Install one TOGGLER for Drywall Installation m Drill 1 2 diameter hole in your wall at the mounting point m Insert a TOGGLER into a hole metal end first gt Pull the plastic ring end so the metal channel rests flush behind the wall With your other hand slide the plastic cap along the straps until the flange of the cap is flush with the wall Place your thumb between the plastic straps Push side to side snapping off the straps at the wall Insert a 1 5 8 long screw into the TOGGLER but don t tighten all the way Leave the bolt head about 1 4 from the plastic cap B STEP 9 Install remaining TOGGLERs This is a two person step Lift the eNook Frame onto the bolt Using a level to make sure that the Frame is level mark the second mounting point as shown Be sure that
5. t the logo on the tray faces out m Align the 2 holes on the back of the Tray with the pins on the Frame m Slide the Tray into place Attach the tray to the left and right of the frame using 4 workstation screws Do not tighten these screws all the way Install the cover plates one on the left and one on the right of the Tray Slide each Plate over the two workstation screws then down to insert the tabs on the Plate into the notches on the Tray Tighten the workstation screws Workstation Screw 325 5092 00 STEP 14 Insert the Back Panel m Hold the Back Panel so that the fabric covered side is facing you long side up m Place the Panel into the eNook so that the bottom edge is resting on the bottom of the frame Tip the top of the Panel into place and secure with the Tack Board Clip and a 3 8 Phillips head screw inserted through the top of the Frame J 3 8 Phillips Head Screw 325 5172 00 eNook Assembly Instructions 7 STEP 15 Insert Power Strip m Open the bottom door on eNook and slide the Power Strip inside STEP 16 Insert Cable Clips m Cable Clips are provided to help manage your cables Clips can be poked into any of the ventilation holes on the top back or side of eNook Twist the ends of the clips to keep the cables in place Congratulations Your assembly is complete 8 Questions Call us at 800
6. wer driver with a Phillips bit attach the first 1 1 2 long screw at that mounting point but don t tighten all the way to the wall Stop tightening when the screw head is about 1 4 away from wall eNook Assembly Instructions 3 STEP 5 Lift eNook Frame onto screws Lift the eNook frame onto the first mounting screw Keyhole slots on the frame are spaced every 2 so you can position the eNook where you want it While one person holds the eNook frame level the second person marks the installation point of the second 1 1 2 long screw Make sure that the second screw goes into a stud too Remove the frame from the wall and drill the second hole with the 1 8 drill bit Using a Phillips driver attach the second 1 1 2 long screw Stop tightening when the screw head is abut 1 4 away from the wall Lift the frame onto the two mounting screws STEP 6 Attach Lower Screws to Studs Once the frame is on the wall mark the mounting points for lower screws into the same studs Using the 1 8 drill bit drill one hole in each stud about 1 1 2 deep Attach the 1 1 2 long screws and tighten all four screws fully so that the Frame is snug against the wall Proceed to Step 11 STEP 7 Determine the Mounting Point on Drywall Determine the optimal desk height for the eNook work surface refer to image for typical shelf heights Measure up 14 3 4 from the shelf height and mark that point on one stud That
7. you mark your spot in the center of the small keyhole 6 6 6 8 6 6 8 8 Mark the third and fourth mounting points along the bottom hole array Set aside the Frame Drill 1 2 diameter holes on the 2nd 3rd and 4th mounting points and install TOGGLERs as instructed above eNook Assembly Instructions 5 STEP 10 Insert Screw and Install Frame m Insert one 1 5 8 long screw into the top two TOGGLERs but don t tighten all the way Leave the screw head about 1 4 from the plastic cap Lift the Frame onto the top two screws Install the bottom two screws then tighten down all four screws STEP 11 Install Four Fasteners onto Main Unit Using your Hex Driver install two black Workstation Screws onto the side walls but don t tighten all the way Stop tightening when the screw head is about 1 4 from tight Workstation Screw 325 5092 00 STEP 12 Attach Main Unit to Frame Open the top and bottom doors and find the angle slots on the Frame Lift the Main Unit onto the Frame by aligning the two Workstation Screws on the Frame with the angle slots Make sure that both fasteners are captured m Using a 5 32 hex driver tighten down the workstation screws 6 Questions Call us at 800 325 3841 or visit anthro com We re happy to walk you through the assembly STEP 13 Insert the Bottom Tray m Place the Bottom Tray on the eNook shelf so tha
Download Pdf Manuals
Related Search