Chief QMP1MM1 mounting kit
Contents
1. Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office 1 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 4 4 D is2. button head cap screws J and two 10 flat washers L through the top two holes in the assembly bracket See Figure 2 Figure 2 IMPORTANT If the display being installed has a recessed mounting surface the display must be assembled to the mount prior to mount installation See Display Installation section before proceeding 4 Insert top of height adjust assembly A over lip on top of assembly bracket C See Figure 3 Figure 3 Swing height adjust assembly A down flush against assembly bracket C See Figure 4 Figure 4 Installation Instructions QMP1MM1 6 Tighten set screw using 5 32 hex key N See Figure 5 A A CAUTION IMPROPER INSTALLATION CAN LEAD TO CAUTION IMPROPER INSTALLATION CAN LEAD TO lad 22 DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY DAMAGE EQUIPMENT sure set teardrop mounting holes must be facing downward for proper screw engages back side of assembly bracket on cart stand installation Reposition Centris cupif required column See Figure 5 Centris Cup Cart stand column Figure 5 Figure 6 DISPLAY INSTALLATION 4 Install two M4 x 12mm Phillips head cap screws F through f the lower mounting holes Centris i
3. INSTALLATION INSTRUCTIONS Music Stand Height Adjust Single Monitor CHIEF QMP1MM1 raxess series QMP1MM1 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voidi
4. draaier Serrez les fixations Tournevis a pointe cruciforme KL lt Loosen Fastener Aflojar elemento de fijaci n Hex Head Wrench Llave de cabeza hexagonal Befestigungsteil l sen Sechskantschlussel Desapertar fixador Chave de sextavada Allentare il fissaggio Chiave esagonale Bevestiging losdraaien Zeskantsleutel Desserrez les fixations Cl a t te hexagonale TOOLS REQUIRED FOR INSTALLATION 3 32 included 5 32 included 3 16 included J 2 10 24 x 1 2 Y S e 9 D 4 E 4 M4 x 30 M4 x 20 S GA G 4 Assembly bracket 500 x 194 x 375 652 4 5 16 18 5 8 GA 4 500 194 x 750 1 3 32 N 1 P 1 5 32 9 3 16 1 1 Installation Instructions ASSEMBLY The QMP1MM1 is designed to be attached to Chief carts and stands 1 Slide cart stand bracket B onto cart stand column not included ensuring that cart stand bracket tab slides into the front of cart stand column See Figure 1 2 Fasten the bracket to the cart stand using four 5 16 18 x 5 8 button head cap screws K See Figure 1 Cart stand column ARN not included Figure 1 3 Attach assembly bracket C to cart stand bracket B using two 10 24 x 1 2
5. ng of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the QMP1MM1 up to and including the display does not exceed 25 Ibs 11 3 kg Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury PW OT 90 PIVOT 4180 III DIMENSIONS INCHES 1 1 Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Phillips Screwdriver Destornillador Phillips Befestigungsteil festziehen Kreuzschlitzschraubendreher Apertar fixador Chave de fendas Phillips Serrare il fissaggio Cacciavite a stella Bevestiging vastdraaien Kruiskopschroeven
6. nt turns See Figure 6 section for detail Align two screws F with the two top teardrop mounting 2 Carefully place display face down on a clean and dry holes on the Centris cup and lower Centris cup onto surface installed screws 3 Determine depth of recessed mounting holes relative to back surface of display QMP1MM1 Installation Instructions 4 Select proper length spacer and screw from table below NOTE If necessary cable management bracket attach screws IMPORTANT All spacers used should be the same may be loosened Using length If the recess depths result in multiple spacer lengths then select the longer spacer IF recess DEPTH is THEN use spacer AND screw 3 8 or less G 3 8 long E M4 x 20mm More than 3 8 up 3 4 long D M4 x 30mm and including 3 4 Attach Screws 5 Place the four spacers G or H over each mounting hole on the back of display See Figure 8 6 Orient mount so that mounting holes in the Centris cup are aligned with the holes in the spacers G or H rotate the Centris cup as required See Figure 8 tion CLOSED Position View from Bottom Sir CAUTION IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of Figure 9 improper size may damage your display Proper screws will ea
7. nto the display The mounting holes on the back of the display will be flush with See Figure 7 the back surface or recessed into the back Refer to the applicable installation procedure below Swing Arm Flush Display Installation A CAUTION IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes A CAUTION IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris bracket 5 Tighten all screws Do not overtighten Figure 7 1 Ensure Centris cup is able to swivel and tilt easily yet still gure be tight enough to hold display in desired position Adjust 6 as required before proceeding See Adjustment section Proceed to Cable Management section for detail Swing Arm Recessed Display Installation 2 Carefully install two M4 x 12mm Phillips head cap screws 1 Ensure Centris bracket is able to swivel and tilt easily yet F into the upper mounting holes on the display Thread still be tight enough to hold display in desired position screws completely into display then back out 3 complete Adjust as required before proceeding See Adjustme
8. shown for clarity Figure 11 3 Reinstall display See Display Installation section Swing Arm Tension 1 Using 3 16 hex wrench loosen or tighten adjustment screw s as necessary See Figure 12 Display not shown for clarity Figure 12 Arm Height Adjustment IMPORTANT It is important that the 1 1 be attached to the cart stand AND display be attached to the QMP1MM1 BEFORE attempting to adjust the height adjust arm 1 Using 5 32 hex key slightly loosen or tighten the adjustment screw as necessary See Figure 13 e If display settles on its own then rotate adjustment screw counterclockwise towards the symbol e If display rises on its own then rotate adjustment screw clockwise towards the symbol NOTE It may be necessary to raise or lower the height adjustable arm to expose the adjustment screw Display attached before adjusting height adjust arm Ly ois Adjustment Screw Figure 13 1 1 Installation Instructions CHIEF raxess series Chief Manufacturing a products division of Milestone AV Technologies 8832 002046 00 2011 Milestone AV Technologies Duchossois Group Company www chiefmfg com 01 11 USA International Europe Asia Pacific gt TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918
9. sily and completely thread into display mounting holes 7 Install four M4 20mm E or four M4 x 30mm D Phillips CAUTION Ensure that adequate cable slack exists for head cap screws through the mounting holes in Centris cup movement of display and that cables will not be pinched through the spacers or into display See Figure 8 when bracket is closed Tighten all four screws Do not overtighten 3 Carefully insert cables into bracket See Figure 10 Return to mount installation section to continue typical Cable Management Bracket in open position lt gt Display not shown for clarity Figure 10 E TOP 4 Close cable management bracket by sliding it back towards the centerline of the arm See Figure 9 Figure 8 NOTE If necessary cable management bracket attach screws may be tightened using 3 32 hex key M CABLE MANAGEMENT 1 Attach all cables to display Installation is complete 2 Open the cable management bracket on the height adjust assembly A by sliding it towards the edge of the arm See Figure 9 Installation Instructions QMP1MM1 ADJUSTMENTS Centris Head Tension Adjustment 1 If previously attached disconnect cables from display remove display 2 Using Phillips screwdriver slightly loosen or tighten the adjustment screw as necessary See Figure 11 Adjustment Screw Display not
Download Pdf Manuals
Related Search