Samsung SCB-9050
Contents
1. When the resistance value of copper wire is at 20 68 Copper wire size AWG 24 0 22 322 0 33 320 0 52 18 0 833 Resistance 0 m 0 078 0 050 0 030 0 018 Voltage Drop V m 0 028 0 018 0 011 0 006 Deviations may occur depending on the type of power cable shown in the chart above and on the wiring manufacturer 3 Notes A 22 18 gauge power wire is recommended for this camera Voltage reinforcement will occur based on the length of the power wire If the adapter output wire is too long camera performance may suffer Startup 1 The START screen will appear after the power has been turned on 2 After completion of initialization thermal images will be displayed approx ten seconds after engaging the power The sensor will not operate properly immediately after the power is turned on or when switching between HIGH and LOW ranges As a result thermal images will not display consistently for several seconds Menu controls can be used to save values to be applied at subsequent start up of the SCB 9050 9051 If values are not saved then the last saved settings will be applied Thermal Night Vision Camera 12 User Guide Calibration NUC MODE This device will perform a calibration necessary for imaging NUC after the internal shutter closes During NUC the screen will freeze momentarily Please note that this is not a malfunction Monitor Communications Connection m2. Thermal Night Vision Camera SCB 9050 9051 User Guide Before installing and operating this product please read this manual thoroughly ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is A intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will b
3. Connecting the Monitor Connect the video output terminal on the rear of this product to the monitor IR camera Monitor Refer to the owner s manual for each device Connection methods employed may differ depending on the monitors and peripheral devices used Before connecting devices ensure their power is turned off Adjust the 750 Hi Z conversion switch for each device based on the following illustration Select Hi Z for intermediate video receivers and 750 for end equipment IR camera Intermediate video receiver End equipment Thermal Night Vision Camera 13 User Guide Installing the Camera WRS485 Communications Controls Using RS485 communications function settings menus can be adjusted using the Samsung Techwin DVR or System controller 1 Controlling menus using a PC Using an RS485 converter connect the camera s RS485 control terminal to a serial cable Example PC serial board COM1 serial cable RS485 converter camera RS485 control terminal 2 Controlling menus using a DVR system controller Connect an RS485 cable TRX TRX to an RS485 control board connection terminal capable of connecting to the DVR system controller External communications cable RS485 control terminal CONNECTION TERMINAL TRX 485 CONNECTION TERMINAL TRX 485 Notes gt Communications Settings Default Values camera default values at the time of shipment Ple
4. and H Range settings Select AUTO to allow the settings to automatically change between L Range and H Range based on the surrounding temperature Choose L to keep the temperature range at L Range regardless of the surrounding temperature In the same way select to always have the temperature range set at Range 3 Press the LEFT button or RIGHT button while the cursor is aligned with 3 RANGE to switch the RANGE setting from AUTO L H AUTO Default value AUTO b 3 RANGE AUTO 4 Press the SET button while the cursor is aligned with 4 to calibrate Screen operations will then be temporarily suspended gt 4 NUC NUC Non uniformity Correction is a menu calibrating all pixel s characteristics to get better image Select an NUC operation mode If you choose MANUAL the user is to perform NUC manually instead of having the device conduct calibration automatically gt 5 MOOE INTERVAI 5 Press the SET button while the cursor is aligned with 5 NUC MODE to display the following NUC MODE sub menu Press the LEFT button or RIGHT button while the cursor is aligned with 5 NUC MODE to switch from INTERVAL gt AMB gt MANUAL gt INTERVAL Press the SET button again to adjust the sub menu Select 2 RETURN to confirm the current setting and go back to the MAIN SETUP menu screen Default value INTERVAL INTERVAL An NUC will be performed at the specified INTERVA
5. and go back to the SPECIAL SETUP menu screen Default value OFF C TEMP ADJ Use this option to change the temperature unit Press the button while the cursor is aligned with 4 TEMP ADJ to change temperature display on off and temperature unit C F e Don t use SCB 9050 9051 to detect anything Measurement error is 15 for objects that have 0 100 C O RESET Reset Use this option to restore each item to its default setting Press the SET button while the cursor is aligned with 5 RESET to restore each item to its factory default setting Please note however that neither TV SYSTEM nor COMM can be changed Select 6 RETURN to go back to the SPECIAL SETUP menu screen Use this option to change the BAUD RATE to one of four settings 38 400 bps 19 200 bps 9600 bps 4800 bps Press the LEFT button or RIGHT button while the cursor is aligned with 2 BAUD RATE to switch the BAUD RATE setting from 4800 gt 9600 19 200 38 400 4800 Select 6 RETURN to confirm the current setting and go back to the SPECIAL SETUP menu screen Default value 9600 bps UART MODE Parity Settings Mode Use this option to adjust parity settings Press the LEFT button or RIGHT button while the cursor is aligned with 3 UART MODE to switch the UART MODE setting from 8 1 8 0 1 8 N 1 8 E 1 Please note that both the bit length 8 and the stop bit 1 are fixed Select 6 RETURN to confirm
6. contact input Active LOW LEFT KEY LEFT contact input Active LOW RIGHT KEY RIGHT contact input Active LOW SET KEY SET contact input Active LOW GND GND MD Terminal used when product is shipped from the factory Before supplying a terminal block with power verify that the wiring has been properly connected Operating the Camera Function Menu Configuration Function Explanation BRIGHTNESS AUTO MANUAL level ranging from 1 10 CONTRAST AUTO MANUAL level ranging from 1 10 RANGE AUTO L H NUC NUC INTERVAL AMB MANUAL NUC MODE INTERVAL OH 1MIN 24H OMIN AMB 0 1 C 10 0 C 3D DNR OFF L M H SHARPNESS 0 5 ZOOM OFF X2 X4 POLARITY BW WB MRE AN COLOR ONO COLOR1 COLOR2 ISOTHERM ON OFF L_RANGE 40 C 150 C R_RANGE 0 C 560 C TV SYSTEM TSC PAL LANGUAGE ENGLISH KOREAN JAPANESE COMM ADJ CAMERAID 0 255 BAUD RATE 4800 9600 19 200 38 400 UART MODE BIT PARITY STOPBIT 8 0 1 SPECIAL 8 N 1 8 E 1 RET PKT ON OFF CAMERA ID ON OFF TEMP ADJ TEMP DISP ON OFF TEMP UNIT C F RESET SAVE SAVE EXIT EXIT Thermal Night Vision Camera 1 User Guide Main Menu LEVEL BRIGHTNESS AUTO MANUAL al LEVEL CONTRAST AUTO MANUAL RETURN RANGE AUTO LOW HIGH NUC H MIN AMB NUC MODE INTERVAL RETURN AMB RETURN M
7. 010 03 23 SAMSUNG TECHWIN CO LTD QUALITY CONTROL MANAGER Legal Representative in Europe Signature Full Name Position Place Date SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon 1 dong Jungwon gu Seongnam si Gyeonggi do Korea 462 703 TEL 82 31 740 8151 8 82 31 740 8145 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungsecurity com P No Z6806096101B VAN 10 03
8. ANUAL 3D DNR L M H OFF SHARPNESS 0 5 D Z00M x2 x4 OFF POLARITY BW WB IMAGEADJ COLOR MONO COLOR1 COLOR2 ON OFF a ISOTHERM 1 RANGE TH SETUP H RANGE TH RETURN TV SYSTEM NTSC PAL LANGUAGE ENGLISH CAMERA ID BAUDRATE UART MODE SPECIAL VEM RET PKT SETUP DISPLAY ID RETURN TEMP DISP TEMP ADA TEMP UNIT RESET RETURN SAVE EXIT Thermal Night Vision Camera 19 User Guide Function settings may be adjusted using the internal switches after removing the rear cover Refer to 5 Interface for directions on how to remove the rear cover UP button Move the menu cursor up RIGHT button Increase the settings value of the selected item DOWN Key Move the menu cursor down LEFT button Decrease the settings value of the selected item SET button If a 4 icon is displayed Move to a screen where you can select settings values move down a level If a 4 icon is not displayed Execute or adjust the selected item UP 4 SET Push gt lt RIGHT Y LEFT t DOWN lt Control buttons gt Press the SET button to display the MAIN SETUP menu screen The MAIN SETUP menu uses a tree structure When you select a function a sub menu will appear Use the UP button or DOWN Bi BRIGHTNESS AUTO Use the RIGHT button or LEFT button to select the item you button to change the status of would like to set the corresponding setting P 1 BRIGHTNESS AUTO 1 Press the SET button while th
9. L AMB An NUC will only be performed when a temperature change meeting the set temperature 0 1 C 10 0 C is detected by the internal temperature sensor MANUAL An NUC will not be performed Use this menu to adjust images After you select this option the following sub menu will appear 3D DNR Noise Reduction E 1 COLOR Press the LEFT button or the RIGHT button to limit the Use this option to set the color of images When COLOR1 is selected high temperature amount of noise produced Default value M areas will be shown in red while low temperature areas will be displayed in blue If COLOR2 chosen high temperature areas will be shown in yellow while low temperature areas will be displayed in blue When MONO is selected high temperature areas will be shown in white while low temperature areas will be displayed in black ISOTHERM SHARPNESS Edge Emphasis ISOTHERM can apply colors to the area whose temperature range over L RANGE TH or L Emphasis 3 RANGE TH in the screen Use this option to use image processing to emphasize 13D DNR OFF L RANGE TH Minimum temperature in the ISOTHERM s area when RANGE is L edges Press the LEFT button or RIGHT button while the ld ao pig H RANGE TH Minimum temperature in the ISOTHERM s area when RANGE is H cursor is aligned with 2 SHARPNESS to switch the APOARIY RETURN Confirm the current setting and go back to the IMAGE ADJ sub menu scree
10. S485 communications CAMERA ID the ID will then be set stored If the CAMERA ID was set incorrectly exit without saving Press the SET button while the cursor is aligned with 9 EXIT to close the MAIN SETUP menu b 9 EXIT Although the infrared sensor has been built using high precision technology please understand that there may be times when pixels may be lost or remain stuck flashing Also be aware that continuously monitoring high temperature object beyond a certain period of time may produce an afterimage In cases where the product instal more the camera s focus will lation site experiences a sudden change in temperature dropping by 15 C become blurred with regards to subjects located within three meters _SCB 9050__ BI Detector 320 H x240 H Uncooled VOX Microbolometer Sensor Pitch 23 5um x 23 5um Measured wavelength range 8 14um Video ratio Sensor NTSC 30 fps PAL 25 fps Video output VBS 1 0VP P 570 composite Lens F1 4 f 14mm F1 4 f 50mm Focus Range 0 5m co Factory default 3m cs Pan Focus 27M ce Pan Focus Viewing angle H x V 30 x 22 8 9 2 x 6 9 IFOV Instantaneous field of view 1 68mrad 0 47 mrad Digital zoom 2x 4x Noise reduction function 3D DNR 4step Low Midium High Off Polarity function BW Black amp White WB White amp Black Detecting tempe
11. ase use Samsung Techwin Protocol or Pelco D Protocol when controlling the camera with a separate controller Monitoring Guidelines After thermal images appear the camera will begin to monitor its range of coverage 1 Do not adjust the focus if there is no particular point of focus to monitor 2 For an in depth explanation of the controls used with the SCB 9050 9051 refer to the section detailing how the camera is operated on page 16 During monitoring the SCB 9050 9051 will capture heat sources and display the resulting images on the monitor 1 If the subject environment experiences a dramatic change in temperature during monitoring be sure to set NUC MODE to either an INTERVAL of 10 MIN or less or an AMB of 1 0 C or lower 2 Please be aware that because this is an infrared camera reflections not visible to the naked eye may still be displayed Images reflected off glass or mirrors located in front of the camera may become visible Thermal Night Vision Camera 14 User Guide 3 Always carry out an NUC whenever sunlight or high temperature objects are within the field of view 4 When the camera is used continuously for a long period of time pay attention to the buildup of dirt on the lens A dirty lens may result in phenomena such as shortened detection distances 5 Even if the same item is being monitored changes in environmental conditions such as rain and fog will affect detection distance While operating the camera
12. be aware of how such changes may influence detection distance Storage Attach the lens cap before storing this device Ensure that the storage area is kept within the allowable temperature range listed in this device s product specifications Do not place this device in a location where condensation may occur Q Interface Interface A user interface terminal block is attached to the inside of this device After making adjustments to the internal terminal block ensure that the back cover is properly attached Notes Leakage may occur if the back cover is not properly attached Thermal Night Vision Camera 15 User Guide i Rear Terminal Placement POWER LED Power ON Lit G FORE pm e AbnormalityANarning Flashing Terminal Block A m Connector specifications and signals Function Chart gt Function Explanation Notes 85485 I F R D Operates the RS485 I F Because full duplex communication is supported this function is used to update F W Standard users should utilize the same cables as those employed at the time of shipment Shipment status R D gt TRX R D gt TRX Communication terminator settings Default value ON If multiple cameras are installed Turn only the camera measuring the furthest distance ON and the remainin
13. e cursor is aligned with 1 BRIGHTNESS to display the BRIGHTNESS sub menu shown below Press the LEFT button or RIGHT button while the cursor is aligned with AUTO to switch the BRIGHTNESS AUTO ADJUST setting from ON OFF ON Press the LEFT button or RIGHT button while the cursor is aligned with MANUAL to adjust the BRIGHTNESS over ten different levels 1 5 2 334 gt 55 gt 6 gt 7 gt 8 gt 9 gt 10 gt 1 Select 2 RETURN to confirm the current setting and go back to the MAIN SETUP menu screen Default value AUTO ON gt 2 CONTRAST MANUA 2 Press the SET button while the cursor is aligned with 2 CONTRAST to display the following sub menu Press the LEFT button or RIGHT button while the cursor is aligned with AUTO to switch the CONTRAST AUTO ADJUST setting from ON OFF ON BRIGHTNESS gt LMANUAL 2 RETURN I 6 Press the LEFT button or RIGHT button while the cursor is aligned with MANUAL to adjust the CONTRAST over ten different levels 1 2 3 gt 4 gt 5 6 gt 7 8 9 10 1 Select 2 RETURN to confirm the current setting and go back to the MAIN SETUP menu screen Default value 6 n order for the CONTRAST AUTO setting to be enabled the BRIGHTNESS AUTO setting must already be turned on Accordingly if AUTO cannot be set to ON enable the BRIGHTNESS AUTO setting and then turn on the CONTRAST AUTO setting Use this option to switch between an L Range
14. e required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes Features Warnings amp Cautions Warnings Cautions Overview e External Part Names E Names of external camera parts Names of internal camera parts E Assembly Adjustment Methods Installing the Camera Monitor Communications Connection Operating the Camera Function Menu Configuration Main Menu Function Settings Methods BRIGHTNESS The SCB 9050 9051 Thermal Night Vision Camera is a contactless monitoring device capable of measuring the surface temperatures of all target areas and displaying the resulting data via temperature distribution images thermal images Because the SCB 9050 9051 is equipped with a two dimensional uncooled thermal sensor microbolometer incorporating the latest technology neither sensor cooling nor sensor maintenance are required In addition its sensor boasts long wavelength sensitivity detecting infrared radiation with wavelengths between 8 14 um from targets and background al
15. g cameras OFF Video output Video Acts as a composite video signal output Switch between NTSC PAL using the menu PIN Name Explanation R RS485 Communications Non inverting input output Power supply POW Provides power AC 24 V 50 60 Hz R RS485 Communications Inverting input output D RS485 Communications Inverting input output D RS485 Transmission Non inverting input output G Ground Video Composite video signal Impedance 75 0 G Ground POW Power input AC 24 V POW Power input DC AC 24 V KEY contact output Operates menu controls Has the same connection as the circuit board KEY This output is provided for adjustment purposes For that reason please refrain from extending the controls to several meters or longer For remote control operation use RS485 I F RS485 Terminator SW Terminator ON 11 2 Terminator OFF 2 3 Multi Direction S W same connector as Terminal Block Terminal Block B PIN Name Explanation Notifies users using the LED display whether the power is ON OFF and whether a device abnormality or warning has occurred Power ON Lighting Device Abnormality Warning Flashing UP KEY UP contact input Active LOW KEY controls Enables operation of the menu controls Used to make adjustments DOWN KEY DOWN
16. lowing it to produce high resolution thermal images with minimal impact from sunlight even during outdoor daytime monitoring in clear weather Samsung Techwin cares for the environment at all product manufacturing Stages to preserve the environment and is taking a number 0f steps to provide customers with more environment friendly products The resents Samsung Techwin s will to create environment friendly pi indicates that the product satisfies the EU RoHS Directive 4 gt 2 E22 Warnings amp Cautions The following points are presented in order to promote customer safety and prevent property damage After reading this information be sure to use the product in the correct manner Please direct any product inquiries towards the merchandiser from which the device was purchased Be aware that if service is carried out customers are responsible for any costs pertaining to the use of expensive ladders or other equipment Ensure that the power plug is disconnected around times in which electrical storms are experienced This prevents fire and product failure This product is an auxiliary device that is used as part of a monitoring system Samsung Techwin will not be held liable in cases when personal or property damage is caused due to theft fire or other unavoidable occurrences Explanation of Warnings Cautions Displays There is a risk of death or serious injury if the designated instructio
17. n SHARPNESS setting from 0 5 Select 5 RETURN to FOUND confirm the current setting and go back to the MAIN SETUP RETURN mg menu screen Default value 4 Z00M Digital Zoom Settings Press the LEFT button or RIGHT button while the cursor is aligned with 3 0 200 to switch the zoom setting from OFF X2 times two X4 times four OFF Select 5 RETURN to confirm the current setting and go back to the MAIN SETUP menu screen Default value OFF Use this menu to adjust environment settings items related to areas such as screen display video O POLARITY WG o output and communications Press the SET button while the cursor is aligned with 7 SPECIAL to Use this option to set the black white properties of images 13D DNR OFF display the following sub menu When BW is selected high temperature areas will be S NET o shown in white while low temperature areas will be n 4 POLARITY BW displayed in black If WB is chosen black and white will FCO be displayed in the opposite way as BW Press the LEFT Kai button or RIGHT button while the cursor is aligned with 4 POLARITY to switch the black white inversion setting from BW WB BW Select 5 RETURN to confirm the current setting and go back to the MAIN SETUP menu screen Default value BW Operating the Camera TV SYSTEM Video Output Setting Use this option to adjust the video output setting Press the LEFT bu
18. ns are not adhered to The action is forbidden Disassembly is forbidden instructions are not adhered to There is a risk of personal injury or property damage if the designated Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems a This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal Thermal Night Vision Camera 6 User Guide Refrain from installing the product yourself 8 Both technical expertise and experience are required in order to install the product A fire or electric shock could result if a customer installs the product by themselves Contact your Sales agent for all matters per
19. rature Auto Manual 2step Low 40 150 High 0 540 Communications specifications RS 485 Protocol Samsung Techwin Pelco D Dustproof waterproof protection rating IP66 Operating temperature 30 55 Storage temperature 40 70 Input voltage 24V AC 50 60Hz Electricity consumption 10 5W Operating Heater 22W Outer diameter size 104 W x123 H x352 D mm 104 W x123 H x367 D mm Weight Camera 2 2Kg Image Processing AGC amp DDE NETD Low range 80mK 80mK High range 300mK Check the points listed below if the product appears to be malfunctioning If the problem continues please contact the sales agent from whom the product was purchased f nothing can be seen onscreen Verify that the power source is connected properly and that the device is receiving power Verify that the video signal wire is connected properly If screen images do not appear clearly Wipe the lens with a clean cloth or brush to remove any dust that may be present Adjust the status of the monitor Change the position or angle of the camera if a large amount of bright light is displayed onscreen If the screen is too dark Adjust the status of the monitor Verify that intermediate processing can be performed properly between systems If the camera is operating abnormally or its surface is very hot causing black lines to appear on
20. renches 3 1 5 mm 2 5 mm 3 0 mm Bolts for fastening camera 2 Lens cap User Guide Video signal communications RS485 cable Power cable AC 24 V 50 60 Hz Lens 14 mm Support platform for fastening camera Lens 14 mm Key SW Key SW terminal block IF terminal block SAMSUNG 88 SCB 9050 SE SCB 9051 A screw to fix the focus is located on the bottom of the lens Do not adjust the focus after purchasing this product because it will have been set to the optimum position Incorrectly adjusting the focus will hinder the camera s performance Asun shield is provided with this camera to allow for outdoor installation Using the bolts and hexagon wrenches included in this package fasten the camera unit and sun shield firmly in place Do not use excessive force during assembly Installing the Camera Inputting Power 1 Remove the lens cap 2 Engage the power Use the adapter provided with this product 3 The rated input voltage for this product is AC 24 V 50 60 Hz This device is not fitted with a power switch The device must be provided with power to turn it After checking the label on the cable on the right side of the camera connect the output cable of the provided adapter
21. screen Verify that the power voltage received by the camera conforms to the proper rating Also confirm whether performance is affected by the time of day If RS485 communications cannot be carried out Verify the polarity of the RS485 communications terminal and the arrangement of the cables Verify the RS485 communications settings RS485 Communication Settings Default Values 0104 Communications Communications Camera No Speed Mode Data Reception 1 9600 8 EVEN 1 In use NS SCB 9050 SCB 9051 DECLARATION OF CONFORMITY Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Name European Representative Address Equipment Type Environment Model Name Beginning Serial NO Year of Manufacture Conformance to 2004 108 EC SAMSUNG TECHWIN CO LTD SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 Thermal Night Vision Camera SCB 9050 9051 C5BY6V3Z300001X 2010 03 23 EN 55022 2006 EN 50130 4 2003 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer Signature Full Name Position Place Date FD Gu BONJENG GU CHANGWON KOREA 2
22. taining to installation Always install a um rod when setting the product up independently outdoors S p Failure to obey this warning could result in product failure electric shock or fire Do not touch the power plug with wet hands Failure to obey this warning could result in an electric shock O AWarnings Stop using the product if smoke is emitted from the camera or an abnormal amount of heat is produced Failure to obey this warning could result in a fire Do not install the product in an insecure mounting location Failure to obey this warning could result in the product falling off Do not disassemble the product or insert foreign objects Pr amp Failure to obey this warning could result in a product failure or fire Thermal Night Vision Camera D User Guide Using the product in an area with very hot 55 or higher or cold 30 C or lower temperatures could result in product failure or a reduction in image quality Ensure proper ventilation when installing the product in particularly hot locations A Failure to obey this caution could result in product failure Failure to obey this caution could result in the microbolometer being damaged beyond repair The lens is the most important part of the camera Ensure the lens is kept free of fingerprints etc SCB 9050 9051 camera sun shield Screws for fastening camera 4xM3XL12 L type hexagon w
23. the current setting and go back to the SPECIAL SETUP menu screen Default value 8 E 1 RET PKT Return Packet Setting Use this option to adjust the return packet returned using the same status as the data entered setting Press the LEFT button or RIGHT button while the cursor is aligned with 4 RET PKT to switch the RET PKT setting from ON OFF ON Select 6 RETURN to confirm the current setting and go back to the SPECIAL SETUP menu screen Default value ON Thermal Night Vision Camera 26 User Guide SAVE Use this option to save device settings and establish the basic settings which will be used the next time you start up the device Press the SET button while the cursor is aligned with 8 SAVE to record your current settings to the internal memory If you exit without saving the MAIN SETUP menu will close without any values being updated MAIN SETUP 1 BRIGHTNESS AUTO 2 CONTRAST MANUAL 3 RANGE AUTO 4 5 INTERVAL 6 IMAGE ADJeJ 7 SPECIALI b 8 SAVE 9 EXIT Thermal Night Vision Camera 27 User Guide Do not disengage the power while settings are being saved Notes CD After switching BRIGHTNESS and or CONTRAST to MANUAL and saving your changes images may not be displayed the next time you restart the device To render images in such a case set BRIGHTNESS and or CONTRAST to AUTO or readjust the MANUAL setting lf you save after changing the R
24. tton or RIGHT button while the cursor is aligned with 1 TV SYSTEM to switch the TV SYSTEM setting from NTSC PAL gt NTSC Select 5 RETURN to confirm the current setting and go back to the MAIN SETUP menu screen Default value NTSC C COMM ADJ Communication Settings mode Use this menu to adjust communication settings Press the SET button while the cursor is aligned with 3 COMM ADJ in the SPECIAL SETUP menu to display the following sub menu CAMERA ID Camera ID Settings Use this option to adjust CAMERA ID settings SPECLAL SETUP b LIVSYCTEM PAL 21ANGUAGE ENGLISH 3 COMM 041 4 RESET S RETURN 1 COMM ADJ 1 CAMERA ID 1 b 2 BOUDRATE 4800 3 URAT MODE 8 E 1 4 RETPKT ON SDISPLAYCAMID OFF 6 RETURN4J Press the LEFT button or RIGHT button while the cursor is aligned with 1 CAMERA ID to adjust the CAMERA ID setting to a value from 0 255 The adjusted value will become valid when the setting is saved Select 6 RETURN to go back to the SPECIAL SETUP menu screen Default value 0 BAUD RATE Communications Speed Settings Mode Camera ID ID Display Setting Use this option to adjust the display setting of the currently set Camera ID appears on the top left of the screen Press the LEFT button or RIGHT button while the cursor is aligned with 5 DISPLAY ID 10 Switch the CAMERA ID display setting from ON gt OFF gt ON Select 6 RETURN to confirm the current setting
Download Pdf Manuals
Related Search