Glancetron GT19wide
Contents
1. 1 Z 3 Power on the computer Make sure that the RS232 or USB cable is connected to the computer Be sure that your Enhanced Write Filter is disabled If your EWF is enabled please disable the EWF by using the EWF Manager command Once the EWF is disabled click on the XP driver on the CD ROM and follow the step by step instructions as shown on the pop up windows Custom 1 2 Power on the computer Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the folder file on the CD ROM If you are using a PC running Windows CE follow the instructions below 1 Poweron the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Using Platform Builder build an image file by following the step by step instructions found in the folder file on the CD ROM If you are using a PC running Linux or Apple Mac OS follow the instructions below 1 Poweron the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the folder file on the CD ROM When changing the Touch Interface RS 232 or USB please follow instructions below Uninstall the touch driver Re start the computer Remove the original Touch Interface RS 232 or USB Connect the computer to the Touch Interface RS 232 or USB that you would like to use oi a YS Load the Touch Driver CD2. electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG Table of Contents Usage Notice Precautions aaan nanrnn enen ennenenneneneenrnereuneenrnarernneeraareraarevaneareasevanenvaasevanearnvensnen 1 Introduction About Glancetron GT 19Wide aa aa enenenenennenenenennensnen ven snrn ene ennnr nen venen 2 Touch Screen for Glancetron GT 19Wide nnn ennen ennen venen een 2 le Oi 3 Installation Product OVerVvieWw pesi wialvcimtaccucnd svakeenenm Ret 4 Front VIS Wera ne RATE RENEE NRE RORE ta 4 Bottom view Without Stang nni 4 INS Mi Secur lO esp RAR E EE RA 5 VESA Mount Your Monitor cccccccccceccccccccucccccccccccececnucceceuuuueeeesuaneeeesuueeeeeuuneeers 6 SIS rour WA A NII PRETI RO RO PR N tee and nated ost TN OTTO 7 Remove the Deskstand E nennen ennn vennnnnse erven enne deense ennen 8 Connecting the Display Figure POE U corri ninni een 9 Peel cin ande didas 10 User Controls FrontPanel ControS sa belligeranti dvbicansantanas ten 11 How to Use the OSD Menus iii 12 On Screen Display MENS asana keda nendentieededr acid enneh kant adnehtie sela 13 Appendix POU ce En 14 VAI e AE A a An ae AS aa TAN 15 on og EEE A AE A NEREA TADO IE VEEE N TE TA
3. We have listed the compatible Video Modes of your LCD display in the appendix on page 17 for your reference This product is intended to be supplied by a Listed Direct Plug In Power Unit marked Class 2 or Listed Adapter marked L P S and rated O P 12Vdc 3 0 A minimum Figure 10 1 User Controls Front Panel Controls key Name E Menu A Up Down 4 Enter GIANCEIRON LW NN Pt as Power iy Nae Den gt Kd ee AE EN En How to Use the OSD Menus key Name E Menu A Up Vv Down a Enter dur Power 1 Press the MENU button to pop up the on screen menu and press Up or Down button to select among the six functions in the main menus 2 Choose the adjustment items by pressing the Enter button 3 Adjust the value of the adjustment items by pressing the Up or Down button 4 With the OSD menu on screen press Menu button to return main menu or exit OSD 5 The OSD menu will automatically close if you have left it idle for a pre set time 6 To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal preset a Press Menu key the OSD menu will pops upon display b Press and hold the Menu key again with the OSD menu on the screen the OSD menu will disappear Then press the Power key 1 time while the menu key is sti
4. panel screen with an active matrix thin film transistor TFT liquid crystal display LCD Features include Direct analog signal input Active matrix TFT LCD technology 1366 x 768 WXGA resolution 47cm 18 5 viewable display area 31 47 60 02 KHz horizontal scan 56 75 Hz refresh rate 0 3mm x 0 3mm pixel pitch Auto adjustment function Multilingual OSD user control Kensington security slot 100 mm VESA mount Removable base for flexible mounting solutions Audio 1W x 2 Touch Screen for Glancetron GT 19Wide e 5 wire resistive touch screen for finger and stylus input Surface Anti glare treatment Interface Combo RS 232 Serial USB controller e Transmittance 82 5 e Driver Windows 7 VISTA XP 2000 ME 98 NT4 0 CE XP Embedded Linux Apple Mac OS Package Overview LCD Display Power Cord VGA Signal Cable USB Cable A to B RS 232 Cable DC Power Supply o Audio in Cable Touch Driver CD Quick Start Guide A Screw Installation Product Overview e Front View GLANCE pe KW N A Do o o e Bottom View Without Stand us OOo o EERE EELS TEAS NUNS POWER SWITCH Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products The Kensington lock is not included qa i di Kensington Security S
5. Glancetron GT19 Wide USER s GUIDE Touch Screen LCD Monitors www glancetron com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders The test results show that this device meets the FCC rules Those limits are set to protect residential areas from the devices with harmful emission This device will produce use and radiate radio frequency energy In addition failure to follow the user s manual to install or use this device might produce harmful interference with radio communication Not withstanding the foregoing it does not guarantee that this type of harmful interference does not occur in some special installations The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off Any changes or modifications to this TFT LCD would void the user s authority to operate this device Important Recycle Instructions Lamp s inside this product contains mercury This product may contain other
6. T 15 CR EI AI 15 iO SE SITO 15 Product Dimensions arcieri ea 16 OO Foe 17 Touch Screen Driver Installation uri rr cirie 18 Glancetron GT 19Wide Optional Calibration Tool Install nn 18 Glancetron GT 19Wide Install Instructions onee ennen nennen 19 20 Usage Notice VAN Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture VAN Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit Do e Turn off the product before cleaning e Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopropyl alcohol Use a soft cloth moistened with mild detergent to clean the display housing Use only high quality and safety approved DC adapter Don t Do not touch the LCD display screen surface with sharp or hard objects e Do not use abrasive cleaners waxes or solvents for your cleaning Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In direct sunlight Introduction About Glancetron GT 19Wide The Glancetron GT 19Wide is a 47cm 18 5 flat
7. een Out of Range This message means that the signal of the computer graphic card is not compatible with the LCD display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the LCD monitor will display this message Product Dimensions 457 80 312 20 Side View 214 81 214 17 Y DS Top View Compatibility Modes Mode Resolution H Frequency KHz V Frequency Hz IBM VGA 720X400 31 47 70 IBM VGA 640X480 31 47 60 Apple Mac 640X480 35 00 66 VESA VGA 640X480 37 86 72 VESA VGA 640X480 37 50 75 VESA VGA 800X600 35 16 56 VESA VGA 800X600 37 88 60 VESA VGA 800X600 48 08 72 VESA VGA 800X600 46 88 75 Apple Mac 832X624 49 72 15 VESA XGA 1024X768 48 36 60 VESA XGA 1024X768 56 48 70 VESA XGA 1024X768 60 02 75 VESA WXGA 1280X768 47 77 60 VESA WXGA 1366X768 47 70 60 Touch Screen Driver Installation The Glancetron GT 19Wide is available with both RS232 and USB connections The touch driver is located on the enclosed CD ROM for these operating systems Windows 7 VISTA 64 32 bits XP 2000 ME 98 NT4 0 CE XP Embedded Linux Apple Mac OS Please Note The Glancetron GT 19wide is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is required for general operation of the touch screen A calibration tool can be installed for improved touch po
8. ip as seen in the step 5 diagram Re attach the cable cover Remove the screw CBM M3x6 from the accessory box and insert the screw into the cable cover and monitor as seen in the step 5 diagram p teme ivi Harp RA walt Remove the Deskstand iff F TO Remove 4 screws and then remove hinge Connecting the Display Figure 10 1 To setup this display please refer to the following figure and procedures 1 Be sure all equipment is turned off 2 Connect the DC adapter to the power connector on the monitor and the other end into an electrical outlet 10 1 3 Connect the D SUB cable from the display s VGA input connector to the D SUB connector of your host computer and tighten the screws 10 1 4 Connect the audio in cable from the audio input of your display to the audio out port of your computer 10 1 5 Connect the RS 232 or USB cable from the RS 232 or USB port of your display to the RS 232 port 10 1 or USB port 10 1 of your computer 6 Configure the touch screen Refer to the Touch Screen Driver Installation section on page 18 7 Once the touch screen is configured the monitor is ready for use Notice To ensure the LCD display works well with your computer please configure the display mode of your graphics card to make it less than or equal to 1366 x 768 pixel resolution and make sure the timing of the display mode is compatible with the LCD display
9. l control The monitor backlight level control Fine tune the image to full screen automatically Moving screen image horizontal position to left or right Moving screen image vertical position to up or down The screen image horizontal dot clock adjustment The screen image pixel phase adjustment Moving OSD menu horizontal position to left or right Moving OSD menu vertical position to up or down OSD auto disappear time selection OSD menu language selection English French Japanese Deutsch Spanish Italian Traditional Chinese and Simplified Chinese Factory default value restored Color temperature selection 9300K 6500K 5500K 7500K User Audio volume adjustment Audio On Off control Appendix Troubleshooting If you are experiencing trouble with the LCD display refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well connected described in the Installation section gt Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image gt Check to see if the resolution of your computer is higher than that of the LCD display gt Reconfigure the resolution of your computer to make it less than or equal to 1366 x 68 pixel Problem Image has vertical flickering line bars gt Use Fine to
10. ll being pressed The Lock Unlock menu will appear for 3 seconds c Use the Enter key to select OSD or Power setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal preset a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Enter key to select OSD or Power setting then set at Unlock by pushing the UP or Down button c When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically Please note a When the OSD Lock function is selected this indicates that all the buttons except Power button are now disabled b When the Power Lock function is selected this indicates that the power key is disabled user can not to turn off the monitor by Power key On Screen Display Menus Main OSD Menu ITEM Contrast Brightness Auto Adjust Left Right Up Down Horizontal size Fine OSD Left Right OSD Up Down OSD Time out OSD Language Factory Reset RGB Volume Mute CONTENT The monitor luminance leve
11. lot VESA Mount Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors and corresponding with the standards of flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on an UL listed certified swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used 100 00 Horizontal Slots x 4 tae 89 20 100 00 EQ 100 00 co 98 90 Vertical A Warning Please select the proper screws The distance between the back cover surface and the bottom of the screw hole is 11 mm Please use four M4 screws diameter with proper length to mount your monitor Please note the mounting stand must be able to support at least 13 2 lbs 6Kg Start Your Installation Please follow these instructions so that you can hookup the cables to associated connector lie O Lay the LCD flat on an even surface 2 Move the stand into position as seen in the step 2 diagram 3 4 Connect the cables to the appropriate connectors as seen in the step 4 diagram Remove the cable cover as seen in the step 3 diagram Use step 4 1 diagram if using the RS 232 serial connector Use the step 4 2 diagram if using the USB connector Position all cables under the cover l
12. make an adjustment gt Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display Problem Image is unstable and flickering gt Use Horizontal size to make an adjustment Problem Image is scrolling gt Check and make sure the VGA signal cable or adapter is securely connected gt Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display Problem Vague image characters and graphics gt Use Fine to make an adjustment If this problem still exists use Horizontal size to make an adjustment Warning Signal If you see warning messages on your LCD screen this means that the LCD display cannot receive a clean signal from the computer graphics card There may be three sources for this problem Please check the cable connections or contact your local dealer or our service center for more information No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA signal cable Going to Sleep The LCD display is under the power saving mode In addition the LCD display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any keyboard triggering the mouse or touching the scr
13. sition accuracy See Optional Calibration Tool Install section for more information Glancetron GT 19Wide Optional Calibration Tool Install If you would like to use the Optional Calibration Tool follow the instructions below Please note the calibration tool supports Windows 7 VISTA XP XP Embedded 2000 98 and ME operating systems via USB only Open the CD ROM Select Touch Type Select HID Calibration The HID calibration tool will automatically open From here the user can choose to do the following gt cdl da a a 4 Points Calibration b 9 Points Linearization c 25 Points Linearization d Clear e Draw Test f Advanced In the Advanced settings area the user may do the following l Adjust the Double Click Area Il Enable auto right click and adjust the auto right click time Ill Choose to be either in the HID Mouse Mode or HID Digitizer Mode Windows 7 Vista IV Simply click the Apply button once the settings are finalized Glancetron GT 19Wide Install Instructions If you are using a PC running Windows 7 VISTA XP 2000 ME 98 NT4 0 follow the instructions below I 2 3 4 Power on the PC Be sure the USB or the RS 232 Serial cable is connected from the PC to the LCD display Open the CD ROM Follow the step by step instructions as shown on the pop up windows If you are using a PC running Windows XP Embedded follow the instructions below Express
14. then follow the step by step instructions as show on monitor PLEASE NOTE Don t plug in both the RS 232 and USB cables Doing so may cause a driver conflict making your touch screen inoperable
Download Pdf Manuals
Related Search