LG WD-12270BD washing machine
Contents
1. Detergent for Detergent for Fabric main wash pre wash softener LLU O 8 e Main wash only u LL Pre Wash Main Wash U _L I1 2 Adding Fabric Softener Do not exceed the maximum fill line Overfilling can cause early dispensing of the fabric softener which could stain clothes Do not leave the fabric softener in the detergent drawer for more than 2 days Fabric softener could harden Softener will automatically be added during the last rinse cycle e Do not open the drawer when water is supplied e Solvents benzene etc are not allowable Do not pour fabric softener directly on the cloths 12 3 Detergent dosage The detergent should be used according to the instruction of the detergent manufacture If too much detergent is used more than the recommended amount too many suds can occur and this will decrease the washing result or cause heavy load to the motor Causing a malfunction Use powder detergent only for the front loading washer e Detergent usage may need to be adjusted for water temperature water hardness size and soil level of the load For best results avoid oversudsing 4 Water softener A water softener such as Calgon can be used to cut down on the use of detergent in extremely hard water areas Dispense according to the amount specified on the packaging First add detergent and then the water softener e Use a quantity of deterg2. e When time delay is selected it shows the remaining times to finish the selected program 4 Time left e During washing cycle the remaining washing time is displayed e Recommended program by manufacturer Cotton around 2 hours and 19 minutes Cotton Eco around 2 hours and 39 minutes Synthetic around 1 hour and 22 minutes Delicate around 1 hour and 4 minutes Wool Silk around 1 hour and 1 minute Hand Wash around 52 minutes Quick 30 around 30 minutes Duvet around 1 hour and 21 minutes Drain around 1 minute 2 Self diagnose display e If the washer encounters a fault during operation the associated fault will be displayed PE Water pressure sensing error FE Problem of overfilling water cc Door is not closed Over load in motor LE Over load in motor Water inlet trouble u The washing time may vary by the Drainage trouble Unbalanced load Water temperature trouble The water experienced a power u me oe m m a e failure amount of laundry water pressure water temperature and other washing conditions If an unbalanced load is detected or if the suds removing program operates the If these error letters are displayed please refer to the troubleshooting page26 and follow the guide wash time may be extended Max increasing time is 45minutes 20 Me Before cleaning the washer interior unplug the electrical power c
3. For U K Customer CUSTOMER SERVICES Tel 0870 873 LGLG 5454 Fax 0870 872 7337 P No 3828ER3026V LGEUK SERVICE WEB SITE http uk Ige com Washing Machine OWNER S MANUAL WD M 12270BD WD M 12275BD WD 12271BD WD 12276BD Thank you for buying a LG Fully Automatic Washing machine Please read your owner s manual carefully it provides instructions on safe installation use and maintenance Retain it for future reference Record the model and serial numbers of your washing machine Pia Feature C Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley Tilted Drum and Extra Large Door Opening Tilted drum and extra large opening make it possible to load and unload clothing more easily Water Circulation Spray detergent solution and water onto the load over and over Clothes are soaked more quickly and thoroughly during wash cycle The detergent suds can be removed more easily by the water shower during rinse cycle The water circulation system uses both water and detergent more efficiently RollerJets Washing ball enhances the wash performance and reduces damage to the clothing The jets spray and help tumble clothes to enhance washing performance while maintaining fabric care Built in Heater Internal heater automatically heats the water to the best temperature on selected cycles Child Lock The Child lock prevents children from pressing
4. Unplug electrical power cord dry the drum interior and close the door Remove dispenser drawer drain and dry excessive water from the compartments Store washer in an upright position O oO N Oo To remove antifreeze from washer after storage run empty washer through a complete cycle using detergent Do not add wash load 23 Tann guide This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all check the following points before you contact your service provider Rattling and e Foreign objects such as coins or Stop washer and check drum clanking noise Thumping sound Vibrating noise Water leaks Oversudsing Water does not enter washer or it enters slowly Water in the washer does not drain or drains slowly 24 safety pins maybe in drum or pump e Heavy wash loads may produce a thumping sound This is usually normal Have all the transit bolts and packing been removed Are all the feet resting firmly on the ground Fill hoses or drain hose are loose at tap or washer e House drain pipes are clogged e Water supply is not adequate in area e Water supply tap is not completely open e Water inlet hose s are kinked The filter of the inlet hose s are clogged Drain hose is kinked or clogg
5. Close the door completely or not completely If J is not released call for service Unplug the power plug and call for service Water overfills due to the faulty water valve Close the water tap Unplug the power plug Water level sensor has malfunctioned Call for service 7 Over load in motor u Over load in motor ia The washer experienced a power Restart the cycle failure 26 Tas of Warranty Disposal of your old appliance 1 When this crossed out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002 96 EC All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health For more detailed information about disposal of your old appliance please contact your city office waste disposal service or the shop where you purchased the product What Is Not Covered e Service trips to your home to teach you how to use the product If the product is connected to any voltage other than that shown on the rating plate If the fault is caused by accident neglect misuse or Act of God If the fault is caused by factors other than normal domestic use or use in accordance wit
6. No spin If No Spin is selected the washer stops after draining water The required lamp will light up for identification Lew to use washer Water Temperature Beeper By pressing the Temp Press the Beeper button button the water repeatedly to adjust the O 60 a temperature can be volume of the Beeper 5 30 selected High Low Off nn Cold 30 C 40 C 60 C 95 C e Water temperature can be selected as below according to the program na Gerz Cotton Eco 40 C 60 C Cotton Time Save Cold 30 C 40 C 60 C 95 C Synthetic Cold 30 C 40 C 60 C e This option can be used to reduce the time of a wash program Delicate amp Wool Silk amp Quick 30 amp Hand Wash amp Duvet e To use this option press the Time Save Cold 30 C 40 C button once before the wash program is started The required temperature lamp will light up for identification Door Lock For the more detailed information please refer to the pagel3 Time Left Lights whenever the door of the washer is locked The door can be unlocked by pressing the Start Pause button to stop the washer The door can be opened after a short delay 19 Hi to use washer Display 3 Completion of washing Time Left e When washing cycle is completed is displayed on the Multi 6 Laoi LILI 1 Special function display display When Child lock is selected the idLock lamp is on
7. any button to change the settings during operation A e E R 3 PECCATO aer nare 4 UNS PONTO E ENEN EEE nenne 5 Care before WI HI Gene ee nee 11 PCCW STS MOSM nee 12 F CLIO a EEEE ae PEA VN en ee ei 13 HOW to USC WESEL as sea nee ee ee ee ee 14 Maintenance zeeeeesste here een ee ee 21 Troubleshooting guide nee nee 24 Terms of Warranty cskesecrvccedeetsuceieceacetsavestcaciansnestarstatdacterehanenennaseteienad 27 1 Jarninss READ ALL INSTRUCTIONS BEFORE USE For your safety the information in this manual must be followed to minimize A WARNING the risk of fire or explosion electric shock or to prevent property damage personal injury or loss of life IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the washer follow basic precautions including the following Do not install or store the washer where it will combustible or explosive substances such as be exposed to the weather wax oil paint gasoline degreasers dry Do not tamper with controls cleaning solvents kerosene etc which may e Do not repair or replace any part of the washer ignite or explode Oil may remain in the tub after or attempt any servicing unless specifically a whole cycle resulting in fire during drying So recommended in the user maintenance do not load oiled clothes instructions or published user repair instructions e To avoid such a result carefully follow the that
8. for identification Hi to use washer Time Delay CA 7 o Time Dela Co ER Eu gt Time Dela On HN gt ie ime Left Time Left Preparing washing before starting Time Delay Turn on the water tap Load laundry and close the door Place the detergent and fabric softener in the drawer e How to set Time Delay Press Power button Turn the Program dial to select the program you require Press Time Delay button and set the desired time Press the Start Pause button fineoeay blinks If Time Delay button is pressed 3 00 is displayed The maximum delayed time is 19 00 hours and the minimum time is 3 00 hours Each pressing of the button advances time delay by one hour e To cancel the time delay press the Power button e Time Delay is expected time from the present to the completion of washing cycle or selected process Wash Rinse Spin According to the condition of water supply and temperature the delayed time and the actual washing time may vary 18 33 Spin O 1200 e By pressing the Spin button a the spin speed can be chosen O 400 O No Spin 1 Spin selection Spin speed is available according to the program as follows Cotton amp Cotton Eco amp Quick 30 No Spin 400 800 1000 1200 Synthetic amp Wool Silk amp Hand Wash amp Duvet No Spin 400 800 1000 Delicate No Spin 400 800 2
9. selected O Pre Wash O Rinse Spin Spin Only 1 Start This Start Pause button is used to start wash cycle or pause the wash cycle 2 Pause 1 Bio If you want to eliminate protein stains milk blood chocolate you may select Bio function by pressing the option button If temporary stop of wash cycle is needed press Start Pause button en Fause lie rn er is turned off NB You can select Bio function when AOAIGA SAET AE temperature is higher than 60 C in Cotton e NB The door will not open before 1 to 2 Cotton Eco and Synthetic minutes when Pause is selected or at the end of the wash cycle 2 Soak Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty Available in Cotton Cotton Eco and Synthetic 3 Pre Wash e Use this option for load that need pretreatment Add 17 minutes for pre wash and drain When using Pre Wash option do not use liquid detergent in the main wash comparment Use powder for the main wash e Available in Cotton Cotton Eco and Synthetic 4 Rinse Spin e Use this option to rinse and then spin 5 Spin Only e When you want spin only select this option 16 Hi to use washer Child lock Option Rinse lf you choose to lock the buttons on the control assembly to prevent tampering this function may be selected e Child lock can be set by pressing and holding the Option and Rinse button simultaneous
10. the hose connector Used the horizontal tap Horizontal tap EY e Your machine comes with only cold water connection Extension ta P x e Make sure that there are no kinks in the hose and that it is not crushed Square tap Sn T This equipment is not designed for maritime use or for use mobile installations such as caravans aircraft etc Turn off the stopcock if the machine is to be left for any length of time e g holiday especially if there is no floor drain gully in the immediate vicinity When disposing of the appliance cut off the mains cable and destroy the plug Disable the door lock to prevent young children being trapped inside Packaging material e g Films Styrofoam can be dangerous for children There is a risk of suffocation Keep all packaging well away from children E Installation of drain hose about 100 cm e When installing the drain hose sink secure it tightly with a string Proper securing of the drain hose will protect the floor from damage due to water leakage max 100 cm min 60 cm 4 4 Laundry tub about 100 cm gt about 105 cm max 100 cm min 60 cm 4 4 The drain hose should not be placed higher than 100 cm above the floor e Proper securing of the drain hose will protect the floor from damage due to water le
11. washer has two valves e The Inlet hose which has red connector is for the hot water tap If the washer has two valves the energy is saved by using hot valve nstallation E Normal Tap without thread amp screw type inlet hose 7 Unscrew the fixing screw to 2 Push the connector up till the 3 Push the water supply hose attach the tap rubber packing is in tight contact vertically upwards so that the with the tap Then tighten the 4 rubber packing within in the screws hose can adhere completely to the tap and then tighten it by screwing it to the right Upper Connector Rubber S packing ml Upper Connector f Upper M Connector pa Plate Water supply hose E Normal Tap without thread amp one touch type inlet hose 1 Untighten the upper connector 2 Push the upper connector up till 3 Connect the water supply hose screw the rubber packing is in tight to the middle connector contact with the tap Then pushing the plate down Cee tor ie tighten the 4 screws Fixing screw Nate Upper lt En Connector Plate In case the diameter of the tap is A paer supply a ose large remove the guide plate Turn the middle connector not To separate the water supply to have water leaked hose from the middle connector shut off the tap Then pull the inlet hose down pushing the plate down nun plate amp e Make sure that the rubber seal is inside
12. 9 Button Beeper 2 Dial Program 6 Button Rinse 10 Button Time Save 3 Button Start Pause 7 Button Spin 11 Button Time Delay 4 Button Option 8 Button Temperature Power Program 1 Power e Press the Power button to turn power on and off To cancel the Time Delay function the Power button should be pressed 2 Initial Program e When the Power button is pressed the washer is ready for Cotton program And the other initial conditions as follows So if you want to advance into the washing cycle without changing the program just press Start Pause gt button and then the washer will proceed Initial program Cotton Program Main Wash Normal Rinse 800 rpm 60 C Wool Silk Delicate _ Hand Wash Program 9 programs are available according to the laundry type Cotton Hand Wash Cotton Eco Quick 30 Synthetic Duvet Delicate Drain Wool Silk e Lamp will light up to indicate selected program e When Start Pause gt button is pressed the Cotton program is automatically selected By turning the Program dial the program is selected in order of Cotton Cotton Eco Synthetic Delicate Wool Silk Quick 30 Duvet Drain Regarding to the laundry type for each program Please refer to the pagel3 15 Hi to use washer Start Pause Option SR e By pressing the option re button only one option function be
13. Pump Filter Front loading washing machine 220 240V 50Hz 686mm W x 767mm D x 982mm H 86kg Refer to the Rating Label 2200W No spin 400 800 1000 1200 89 2 0 3 10kgf cm 30 1000kPa The appearance and specifications may be varied without notice to raise the units quality E Accessories Inlet hose 1EA 2 Option Hot Cold 2EA Spanner T Install or store where it will not be exposed to temperatures below freezing or exposed to the weather Properly ground washer to conform with all governing codes and ordinances The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor In countries where there are areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in clean condition at all times Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee E Transit bolts The appliance is fitted with transit bolts to prevent internal damage during transport e Packing and all transit bolts must be removed before using the washer rae When unpacking the base be sure to remove the additional packing support in the middle of the base packing Packing Support Packing support may not be used depending on models E Removing transit bolts 1 To prevent internal damage during 3 Take out th
14. You can only select Bio function when temperature is higher than 60 C in Cotton Cotton Eco and and Synthetic 13 Hi to use washer Delicate 1 Cotton automatically selected upon power on e Press the Power o button to start Press the Start Pause button Initial condition Wash Main wash Rinse 3 times Spin 800 rpm Water temperature 60 C Program Cotton CCST gt TimeDelay t Processing J 3 CO mmaa Time Left O Bio O Rinse Hold 1200 O 95 C O High O Soak Normal Hold 1000 O 60 on O Pre Wash O Rinset O 800 O 40 Low O Rinse Spin Rinset O 400 030 Oo FY Spin Only Normal O No Spin O Cold Off Bw Option Rinse Spin Temp Beeper 2 Manual Selecting Press the Power button to start e Select the conditions which you want to use by pressing each button For selecting the each conditions please refer to the pagel5 page20 Press the Start Pause button Hi to use washer Wool Silk Delicate Hand Wash IDD 1D Pont west ie sor Time DAM Synthetic Quick 30 aii ics fen es re Cotton Eco Duvet Bio Ds nse Hold oy a oa c T Cotton Drain e a 2 a 30 O a Spin Only Normal O No Spin O Cold O Off l f f a GOOOO DoE Option Rinse Spin Temp Beeper a Lt Tu 1 2 3 4 5 6 7 8 9 10 1I 1 Button Power 5 Child lock
15. akage e When the drain hose is too long do not force back into the washer This will cause abnormal noise sen E Level adjustment 1 Adjusting the washing machine level properly prevents excessive noise and vibration Install the appliance on a solid and level floor surface preferably in a corner of the room gt Timber or suspended type flooring may contribute to excessive vibration and unblance errors 2 If the floor is uneven adjust the adjustable feet as required do not insert pieces of wood etc under the feet Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level use a spirit level X After the washer is level tighten the lock nuts up towards of the base of the washer All lock nuts must be tightened 3 In the case that the washing machine is installed on a raised platform it must be securely fastened in order to eliminate the risk that it might fall off X Diagonal Check When pushing down the edges of the washing machine top plate diagonally the machine should not move up and down at all Please check both of two directions If machine rocks when pushing the machine top plate diagonally adjust the feet again E Concrete floors e The installation surface must be clean dry and level e Install washer on a flat hard floor E Tile floors Slippery floors e Position each foot on the Tread Mate and level the machine to suit Cut Tread Mate i
16. ake a few moments before the clothes washer begins to spin The door must lock before spin can be achieved Once started the door can not be opened for safety reasons Wait one or two minutes before Opening the door to give the electric locking mechanism time to release The washing time may vary by the amount of laundry water pressure water temperature and other using conditions lf the imbalance is detected or if the suds removing program works the wash time shall be increased 25 Tann guide Water supply is not adequate in area Check another tap in the house Water supply taps are not completely Fully open tap open Water inlet hose s are kinked Straighten hose s The filter of the inlet hose s are Check the filter of the inlet hose s clogged Drain hose is kinked or clogged Clean and straighten the drain hose The drain filter is clogged Clean the drain filter Load is too small Add 1 or 2 similar items to help Load is out of balance balance the load The appliance has an unbalance Rearrange load to allow proper detection and correction system If spinning individual heavy articles are loaded ex bath mat both robe etc this system may stop spinning or even interrupt the spin cycle altogether If the laundry is still too wet at the end of the cycle add smaller articles of laundry to balance the load and repeat the spin cycle e Is the door opend
17. e 4 bolts along with the rubber transport the special 4 bolts are locked bungs by slightly twisting the bung Keep Before operating the washer remove the 4 bolts and the spanner for future use the bolts along with the rubber bungs If they are not removed it may cause heavy e Whenever the appliance is transported the vibration noise and malfunction transit bolts must be refitted 2 Unscrew the 4 bolts with 4 Close the holes with the caps supplied the spanner supplied 2 l a E Installation place requirement Level floor Allowable slope under entire washer is 1 Power outlet Must be within 1 5 meters of either side of location of washer Do not overload the outlet with more than one appliance Additional Clearance For wall door and floor modeling is required 10cm rear 2cm right amp left side Do not place or store laundry products on top of washer at any times They can damage the finish or controls Drain Hose Washer P a SG A E Positioning Install the washer on a flat hard floor Make sure that air circulation around the washer is not impeded by carpets rug etc e Never try to correct any unevenness in the floor with pieces of wood cardboard or similar materials under the washer If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove an insulating 686x767x982mm covered with aluminum foil on the side facing the cooker or stov
18. e must be inserted between the two appliance e The washer must not be installed in rooms where the temperature can drop below 0 C Please ensure that when the washer is installed it is easily accessible for the engineer in the event of a breakdown With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable and a clearance of approximately 20mm is left between the top of the washer and the underside of the work top m BS Plug Safety Details For U K User IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE This appliance must be earthed Green and Yellow Earth Ole Brown Live O Blue Neutral Ol F N Fuse O Cord grip As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol S or coloured Green or Green and Yellow The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red Ita 13 amp BS 1363 pl
19. ed e The drain filter is clogged and drain filter If noise continues after washer is restarted call your authorized service centre If sound continues washer is probably out of balance Stop and redistribute wash load If not removed during installation refer to Installation guide for removing transit bolts Wash load may be unevenly distributed in drum Stop washer and rearrange wash load Check and tighten hose connections Unclog drain pipe Contact plumber if necessary Too much detergent or unsuitable detergent may cause excessive foaming which may result in water leaks Check another tap in the house Fully open tap Straighten hose s Check the filter of the inlet hose s Clean and straighten the drain hose Clean the drain filter Tin guide Washer does not start Electrical power cord may not be plugged in or connection may be loose House fuse blown circuit breaker tripped or a power outage has occurred e Water supply tap is not turned on Washer won t spin Check that the door is firmly shut Door does not open Wash cycle time delayed Make sure plug fits tightly in wall outlet Reset circuit breaker or replace fuse Do not increase fuse capacity If problem is a circuit overload have it corrected by a qualified electrician Turn on water supply tap Close the door and press the Start Pause button After pressing the Start Pause button it may t
20. ent as for soft water Tips Full load according to manufacturer s recommendation Part load 3 4 of the normal amount Minimum load 1 2 of full load Detergent is flushed from the dispenser at the beginning of the cycle auction E Recommended courses according to the laundry type Energy label data based on program cotton 60 C tested in accordance with EN60456 Proper Time Program Fabric Type Temp in Option Minutes Color fast garments shirts night dresses pajamas and lightly soiled white cotton underwear Soak Cotton Eco Laundry type is the Pre Wash same in Cotton s Rinse Spin 40 C Synthetic poll Acrylic Co i olyester 30 C 60 C Spin Only Delicate laundry easily 30 C Delicate damaged Cold 40 C Wool Silk Machine washable woolens 30 C OO DIK with pure new wool only Cold 40 C Rinse Spin Hand Hand Wash marked Cold Spin Only Wash delicate and wool laundry 30 C 40 C Colored Landry which 30 C Quick 30 is lightely soiled fast Cold 40 C Cotton bedding with filling 20 C duvet pillow blanket sofa Cold 40 C cover with light filling Water Temperature Select the water temperature to the wash cycles Always follow garment manufacture s care label or instructions when laundering Bio If you want to eliminate protein stains milk blood chocolate you may select Bio function by pressing the option button NB
21. h the owner s manual e Provide instruction on use of product or change the set up of the product If the fault is caused by pests for example rats or cockroaches etc e Noise or vibration that is considered normal for example water drain sound spin sound or warming beeps e Correcting the installation for example levelling the product adjustment of drain Normal maintenance which recommended by the owner s manual e Removal of foreign objects substances from the machine including the pump and inlet hose filter for example grit nails bra wires buttons etc e Replace fuses in or correct house wiring or correct house plumbing e Correction of unauthorized repairs Incidental or consequential damage to personal property caused by possible defects with this appliance If this product is used for commercial purpose it is not warranted Example Public places such as public bathroom lodging house training center dormitory If the product is installed outside the normal service area any cost of transportation involved in the repair of the product or the replacement of a defective part shall be borne by the owner 27
22. hen clockwise and insert the drain the hose water does not flow any more turn plug 2 to the original place the pump filter open to the left close the lower cover cap Man m Dispenser drawer After a while detergents and fabric softeners leave a deposit in the drawer It should be cleaned from time to time with a jet of running water If necessary it can be removed completely from the machine by pressing the catch downward and by pulling it out To facilitate cleaning the upper part of the fabric softener compartment can be removed m The drawer recess Detergent can also accumulate inside the recess which should be cleaned occasionally with an old toothbrush e Once you have finished cleaning replace the drawer and run a rinse cycle without laundry E The washing drum f you live in a hard water area limescale may continuously build up in places where it cannot be seen and thus not easily removed Over time the build up of scale clogs appliances and if it is not kept in check these may have to be replaced Although the washing drum is made of Stainless steel specks of rust can be caused by small metal articles paper clips safety pins which have been left in the drum e The washing drum should be cleaned from time to time f you use descaling agents dyes or bleaches make sure they are suitable for washing machine use Descaler ma
23. ly e When child lock is set all buttons are inoperable To deactivate Child lock system press and hold the Option and Rinse button simultaneously again Child Lock To change to the desired program whilst in child lock mode 1 Press and hold both Option and Rinse button together once again 2 Press the Start Pause button 3 Select the desired program and press the Start Pause button again oy Change gt gt the desired gt program Optio inse The child lock can be set at any time and it is automatically canceled when operational errors occur Rinse By pressing the Rinse button the Rinse type can be selected O Rinse Hold O Normal Hold O Rinse O Rinset O Normal 1 Normal Cotton Eco Cotton Synthetic performs 3 Rinses e Wool Silk Hand Wash Quick 30 Delicate Duvet performs 2 Rinses 2 Rinset amp Rinsett Used to additional rinse which may assist in removing traces of detergent residue By selecting Rinset or Rinse function the Rinse Time and the Rinse water are increased 3 Rinse Hold Is selected by pressing the Rinse button repeatedly this function leaves clothes in the washer suspended in the water after a rinse without entering into spin To proceed through to a drain or spin once the rinse hold function is completed using to program dial scroll to the required program The required lamp will light up
24. nce must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance Do not use an adapter or otherwise defeat the grounding plug If you don t have the proper outlet consult an electrician WARNING Improper connection of the equipment grounding conductor can result in risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it does not fit the outlet have a proper outlet installed by a qualified electrician FJpecification Drain Hose Dispenser Door Lower Cover Cap Drain Plug m Name m Power supply E Size m Weight m Wash capacity m Max Watt E Spin speed m Water consumption m Permissible water pressure Shipping Bolts _ Power Plug e If the supply cord is damaged it must be replaced by the manufacturer or its authorized service technician in order to avoid a hazard Control Panel Back of Washer Cold Water Inlet Hot Water Inlet 4 o Adjustable Feet Drain
25. nto 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed X Tread Mate is a self adhesive material used on ladders amp steps that prevents slipping E Wooden floors Suspended floors Rubber Cu e Wooden floors are particularly susceptible to vibration e To prevent vibration we recommend you place rubber cups under each foot at least 15mm thick under the washer secured to at least 2 floor beams with screws e If possible install the washer in one of the corners of the room where the floor is more stable X Insert the rubber cups to reduce vibration X You can obtain the rubber cups p no 4620ER4002B from the LG spares dept Important e Proper placement and levelling of the washer ensure long regular and reliable operation e The washer must be absolutely horizontal and stand firmly in position e t must not Seesaw across corners under load e The installation surface must be clean free from floor wax and other lubricant coatings e Do not let the feet of the washer get wet If feet of the washer get wet slipping may occur 139 Kar before washing E Before the first washing Select a cycle COTTON 60 C add a half load of detergent allow the unit to wash without clothing This will remove residues from the drum that may have been left during manufacturing E Caring before washing 1 Care Labels Look for a care label on your clothes This will tell you abou
26. ord to avoid electrical shock to avoid electrical shock hazards When disposing of the appliance cut off the mains cable and destroy the plug Disable the door lock to prevent young children being trapped inside m The water inlet filter IE error message will blink on the control panel when water does not enter the detergent drawer If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time 1 Turn off the 2 Unscrew the water tap water inlet hose 3 Clean the 4 Tighten up filter using a the inlet hard bristle hose brush E The drain pump filter The drain filter collects threads and small objects left in the laundry Check regularly that the filter is clean to ensure smooth running of your machine A CAUTION First drain using the drain hose and then open the pump filter to remove whatever any threads or objects Be careful when draining if the water is hot Allow the water to cool down before cleaning the drain pump carrying out emergency emptying or opening the door in an emergency 1 Open the lower cover 2 Unplug the drain plug 2 3 Remove out any foreign material cap D by using a allowing the water to flow out At from the pump filter After finger Turn the drain this time use a vessel to prevent cleaning turn the pump filter 8 plug 2 to pull out water flowing on to the floor W
27. outlets Overloaded wall outlets loose or damaged wall outlets extension cords frayed power cords or damaged or cracked wire insulation are dangerous Any of these conditions could result in electric shock or fire Periodically examine the cord of your appliance and if its appearance indicates damage or deterioration unplug it discontinue use of the appliance and have the cord replaced with an exact replacement part by an authorized servicer Protect the power cord from physical or mechanical abuse such as being twisted kinked pinched closed in a door or walked upon Pay particular attention to plugs wall outlets and the point where the cord exits the appliance m Washing Machine is to be connected to the water mains using new hose sets and that old hose sets should not be used E Connecting water supply hose gt Water supply pressure must be between 30kPa and 1000kPa 0 3 10kgflcm gt Don t strip or crossthread when connecting Inlet hose to the valve gt If the water supply pressure is more than 1000kPa a decompression device should be installed e Two rubber seals are supplied with the water inlet hoses these are in order to prevent water leaks e Check water tightness of washing machine connections by turning the tap completely on e Periodically check the condition of the hose and replace the hose if necessary e Make sure that there is no kink on the hose and that it is not crushed Sealing washer gt When your
28. t the fabric content of your garment and how it should be washed 2 Sorting To get the best results Sort clothes into loads that can be washed with the same wash cycle Water temperature and spin speed and different fabrics need to be washed in different ways Always sort dark colors from pale colors and whites Wash separately as dye and lint transfer can occur causing discoloration of white etc If possible do not wash heavily soiled items with lightly soiled one Soil Heavy Normal Light Separate clothes according to amount of soil Color White Lights Darks Separate white fabrics from colored fabrics Lint Lint producers Collectors Wash lint producers and lint collectors separately 3 Caring before loading E Combine large and small items in a load Load large items first Large items should not be more than half the total wash load Do not wash single items This may cause an out of balance load Add one or two similar items e Check all pockets to make sure that they are empty Items such as nails hair clip matches pens coins and keys can damage both your washer and your clothes e Close zippers hooks and strings to make sure that these items don t snag on other clothes Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt 17 A detergent E Adding detergent and fabric softener 1 The Dispenser Drawer
29. ug is used fit a 13 amp BS 1362 fuse 6 nstallation E Electrical connection 1 Do not use an extension cord or double adapter 2 If the supply cord is damaged it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard 3 Always unplug the machine and turn off the water supply after use 4 Connect the machine to an earthed socket in accordance with current wiring regulations 5 The appliance must be positioned so that the plug is easily accessible e Repairs to the washing machine must only be carried out qualified personnel Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local service center e Do not install your washing machine in rooms where temperatures below freezing may occur Frozen hoses may burst under pressure The reliability of the electronic control unit may be impaired at temperatures below freezing point If the appliance is delivered in the winter months and temperatures are below freezing Store the washing machine at room temperature for a few hours before putting it into operation CAUTION CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit that is a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits Check the specification page of this owner s manual to be certain Do not overload wall
30. y contain chemicals that may damage part of your washing machine Remove any spots with a stainless steel cleaning agent Never use steel wool 22 M Jaintenance m The water circulation nozzle e Clean the water circulation nozzle if clogged m Cleaning your washer 1 Exterior Proper care of your washer can extend its life The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent Immediately wipe off any spills Wipe with damp cloth Try not to hit surface with sharp objects IMPORTANT Do not use methylated spirits diluents or similar products 2 Interior Dry around the washer door opening flexible gasket and door glass Run washer through a complete cycle using hot water Repeat process if necessary KA Remove hard water deposits using only cleaners labeled as safe for washing machine m Winterizing instructions lf the washer is stored in an area where freezing may occur or moved in freezing temperatures follow these instructions to prevent damage to the washer 1 Turn off water supply tap 2 Disconnect hoses from water supply and drain water from hoses 3 Plug electrical cord into a properly grounded electrical outlet 4 Add 1gallon 3 8L of nontoxic recreational vehicle RV antifreeze into an empty wash drum Close the door Ul Set spin cycle and let washer spin for 1minute to drain out all water Not all of the RV antifreeze will be expelled
31. you understand and have the skills to carry garment manufacturer s wash and care out instructions e Keep the area underneath and around your Do not slam the washer door closed or try to appliances free of combustible materials such as force the door open when locked This could lint paper rags chemicals etc result in damage to the washer e Close supervision is necessary if this appliance To minimize the possibility of electric shock is used by or near children unplug this appliance from the power supply or Do not allow children to play on with or inside disconnect the washer at the household this or any other appliance distribution panel by removing the fuse or Do not leave the washer door open switching off the circuit breaker before An open door could entice children to hang on attempting any maintenance or cleaning the door or crawl inside the washer e Never attempt to operate this appliance if it is Never reach into washer while it is moving Wait damaged malfunctioning partially until the drum has completely stopped disassembled or has missing or broken parts The laundry process can reduce the flame including a damaged cord or plug retardant of fabrics When a product was under water Please call Do not wash or dry articles that have been service center The risk of electric shock and cleaned in washed in soaked in or spotted with fire SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This applia
Download Pdf Manuals
Related Search