Siig SC-SA0N11-S1
Contents
1. To make this floppy disk copy the contents of the 64bit folder found on the driver CD onto a blank floppy disk then follow the directions below IR Install the board and follow Microsoft procedures to install Windows accordingly At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 64bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again to finish the driver installation then follow the on screen instructions to complete your Windows installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D setup exe click OK Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation Windows XP 32 bit For A New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 32bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft proced2. Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer cover 4 Remove the slot bracket cover from an available PCI Express slot To install the card carefully align the card s bus connector with the selected PCI Express slot on the motherboard Push the board down firmly but gently until it is well seated Replace the slot bracket holding screw to secure the card Device Connection The DP eSATA 6Gb s 2 Port PCIe i e supports one internal and one external Serial ATA hard disk drive Internal Serial ATA port 1 2 Install your hard disk drive s in the chassis Connect the Serial ATA hard disk drive to the system power supply Note For hard drives with both SATA power connector and legacy 5 pin connector use either the SATA power connector or the legacy 5 pin power connector Using both power connectors may damage the hard drive 3 Connect one end of the Serial ATA cable to the hard disk drive Serial ATA Power Figure 2 SATA hard disk drive connections 4 Attach the other end of the Serial ATA data cable to the Serial ATA connector on the DP eSATA 6Gb s 2 Port PCIe i e 5 Replace the computer cover and reconnect the power cord External Serial ATA port External Serial ATA hard disk drives should come with their own accessories In most cases you just need to power up
3. E ATA ATAPI controllers Asmedia 106x SATA Controller should be displayed For Windows XP Server 2003 Double click SCSI and RAID controllers Asmedia 106x SATA Controller should be displayed Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analyst will promptly respond SIG offers a 5 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for 5 years of the product SHG will at our discretion repair or replace with an identical product or product having similar features and functionality the product if defective in materials or workmanship This warranty gives you specific legal rights and you may also have other rights which vary from state to state Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow the steps below to have the p
4. G amp A DP eSATA 6Gb s 2 Port PCle i e Quick Installation Guide amp Introduction The DP eSATA 6Gb s 2 Port PCIe i e adds 2 SATA 6Gb s to PCle equipped computers Features and Benefits Compliantwith Serial ATA specification Revision 3 0 e Supports ATA ATAPI 7 specification e Supports port multiplier e Installs in standard height or low profile chassis with included brackets System Requirements e Desktop PC with an available PCIe slot e Windows 7 32 64 bit Vista 32 64 bit XP 32 64 bit Server 2003 amp 2008 32 64 bit Server 2008 R2 04 0745A 1 Package Contents e DP eSATA 6Gb s 2 Port PCIe iJe adapter e Spare low profile bracket SATA data cable e Driver CD e Quick installation guide Layout Hard Disk LED Pins connect horizontally eSATA connector Serial ATA connector Figure 1 DP eSATA 6Gb s 2 Port PCIe i e Hardware Installation For Low profile systems install the spare low profile bracket now General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1
5. ment then click Next Click Finish Click Yes to complete the installation Server 2003 32 bit For A New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 32bit folder found on the driver CD onto a blank floppy disk then follow the directions below J Install the board and follow Microsoft procedures to install Windows accordingly At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 32bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again to finish the driver installation then follow the on screen instructions to complete your Windows installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D setup exe click OK Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation Windows XP 64 bit For A New Installation A new installation requires a floppy disk for the driver installation
6. roduct repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then Request A Product Replacement to submit a request to SIG RMA or fax a request to 510 657 5962 Your RMA request will be processed if the product is determined to be defective an RMA number will beissued Step 2 After obtaining an RMA number ship the product Properly pack the product for shipping All accessories that came with the original package must be included Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton You are responsible for the cost of shipping to SHG Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA SIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 19 About SIIG Inc Founded in 1985 SIIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio SIIG products offer comprehensive user manual
7. s many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SUG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME DP eSATA 6Gb s 2 Port PCle i e FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SUG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 DP eSATA 6Gb s 2 Port PCle i e is a trademark of SIIG Inc SIIG and the SHG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation All othernames used in this publication are for identification only and may be trademarks of their respective owners October 2011 Copyright 2011 by SIIG Inc All rights reserved
8. t driver CD click Start menu in the Start Search box type D setup exe press Enter Change D to match your CD ROM drive letter 7 At the User Account Control window click Allow Skip this step if not prompted Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu in the Start Search box type D setup exe press Enter Change D to match your CD ROM drive letter At the User Account Control window click Allow Skip this step if not prompted Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation Windows Server 2008 32 64 bit For New Installation J 5 6 Install the board and follow Microsoft procedures to install Windows accordingly After the installation insert driver CD click Start menu in the Start Search box type D setup exe press Enter Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert dri
9. the external drive and connect it to the external port For more information please refer to the external device s manual Software Installation This section provides information on how to install the DP eSATA 6Gb s 2 Port PCIe i e adapter drivers Windows 7 32 64 bit Server 2008 R2 For New Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly After the installation insert driver CD click Start menu in the Search programs and files box type D setup exe press Enter Change D to match your CD ROM drive letter At the User Account Control window click Yes Skip this step if not prompted Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation For Existing Installation 1 24 Install the board and boot up Windows Insert driver CD click Start menu click Start menu in the Search programs and files box type D setup exe press Enter Change D to match your CD ROM drive letter At the User Account Control window click Allow Skip this step if not prompted Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation Windows Vista 32 64 bit For A New Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly After the installation inser
10. ures to install Windows accordingly At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 32bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again to finish the driver installation then follow the on screen instructions to complete your Windows installation For An Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D setup exe click OK Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agreement then click Next Click Finish Click Yes to complete the installation To Verify Windows Installation 1 Use Device Manager to verify installation For Windows 7 Right click Computer click Manage click Device Manager For Windows Vista Right click Computer click Manage click Continue Click Device Manager For Windows XP Server 2003 Right click My Computer click Manage click Device Manager For Windows Server 2008 Right click Computer click Manage Double click Diagnostics click Device Manager For Windows 7 Vista Server 2008 Server 2008 R2 Double click ID
11. ver CD click Start menu in the Start Search box type D setup exe press Enter Change D to match your CD ROM drive letter 4 Click Next 5 Select I accept the terms of the license agreement then click Next 6 Click Finish 7 Click Yes to complete the installation Server 2003 64 bit For A New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 64bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows accordingly At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select Asmedia 106x SATA Controller 64bit then press Enter Note Do not remove the floppy diskette from the floppy drive You need to install the driver once again during the installation Press Enter again to finish the driver installation then follow the on screen instructions to complete your Windows installation For Existing Installation 1 2 Install the board and boot up Windows At the Found New Hardware window click Cancel Insert driver CD click Start menu Run Type D setup exe click OK Change D to match your CD ROM drive letter Click Next Select I accept the terms of the license agree
Download Pdf Manuals
Related Search