Da-Lite Motorized Scenic Roller, 549 x 732 cm
Contents
1. The Da Lite Difference Instruction Book for MOTORIZED SCENIC ROLLER SCREEN M 8 I DA LITE M a DA LITE SCREEN COMPANY INC 3100 North Detroit Street Post Office Box 137 Warsaw Indiana 46581 0137 Phone 574 267 8101 800 622 3737 Fax 574 267 7804 www da lite com e mail info da lite com IMPORTANT SAFETY INSTRUCTIONS When using your video equipment basic safety precautions should always be followed including the following Read and understand all instructions before using 2 Position the cord so that it will not be tripped over pulled or contact hot surfaces 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 he use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons SAVE THESE INSTRUCTIONS INSTALLATION Before proceeding with the installation please read the installation and operating instructions thoroughly Make sure to recheck measurements of screen and hanger locations before installation Area must be clear for screen2. contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA LITE S WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership Printed in U S A 7 84222 Rev 10 10
3. to operate With all lid sections removed from shipping container remove the screws holding the frame to the shipping container 2 per cross brace The screen can now be carefully lifted out of the container METHOD A The frame can be mounted to ceiling with 5 16 diameter threaded rods Level frame from front to back and left to right Mount from all cross braces fig 1 METHOD B Hang from a pipe fly the screen Level frame from front to back and left to right Mount from all cross braces fig 2 NOTE Motor pulley must clear pipe Chains must clear motor tubes SUGGESTED METHOD OF INSTALLATION SUGGESTED METHOD OF INSTALLATION METHOD A SECURE TO CEILING METHOD FLYING PIPE DAN ANY Pipe To Suit Ceiling EUN tl QN To Suit To Suit Jr W Chain To Suit Cross a o 5 16 Threaded Rod 4 NEN 16 Not Pumishod E j Eye Bolts Fon Back B x A tF hed Front 1 i Back Safety Switch Trigger Safety Switch Trigger FIG 1 ELECTRICAL INSTALLATION Screen motors have been internally wired at Da Lite Wiring designated external is completed by installer conforming to local and national codes Refer to wiring diagram on next page Check for satisfactory condition by operating the screen Be prepared to stop sc
4. E BLACK 3 6 AMPS GREEN YELLOW GROUND RED OUT OF CONTROLLER BROWN OUT OF CONTROLLER MOTORIZED SCENIC ROLLER INSTALLATION 120V 240V WALL SWITCH WIRING DIAGRAM FRONT BACK OF OF WALL WALL SWITCH SWITCH OPTIONAL RF REMOTE CONNECTION BLACK DOWN NOTE 20 24AWG WIRE RECOMMENDED FOR CONNECTING WALL SWITCH TO SYCHRONIZATION CONTROLLER IMPORTANT The wall switch terminal block can be connected inside the wiring compartment The controller does not need to be removed from the junction box unless an RF remote is being connected Use caution when removing the controller from the box as it is easily damaged LIMIT SWITCH ADJUSTMENT The stop positions of the screen are preset at the factory If adjustments are necessary the limit switch screws located at the end of each motor can adjust the stop positions Use a 5 32 hex key or a flat screwdriver Adjustments should be made in small increments by turning the adjustment screws a half turn at a time Refer to figure 3 SETTING THE DOWN LIMIT POSITION SCREEN DROPS TOO FAR Left motor as viewed from audience side Turn the white limit switch screw clockwise to decrease the amount of fabric drop Right motor as viewed from audience side Turn the yellow limit switch screw clockwise to decrease the amount of fabric drop After adjusting the limit screws on both motors run the screen down to test the stop position Re
5. ed due to improper handling or treatment after shipment from the factory This warranty does not apply to eguipment showing evidence of misuse abuse or accidental damage or which has been tampered with by person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer Ifitis necessary for the dealer to return the screen or part to Da Lite transportation to and from Da Lite are payable by purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may
6. from audience side Turn the yellow limit switch screw counterclockwise to increase the amount of travel Right motor as viewed from audience side Turn the white limit switch screw counterclockwise to increase the amount of travel After adjusting the limit screws on both motors run the screen up to test the stop position Repeat until the desired position is set LIMIT SWITCH ADJUSTMENT FIG 3 YELLOW UP LIMIT CLOCKWISE LESS UP TRAVEL COUNTERCLOCKWISE MORE UP TRAVEL o 1 B mI a MOTOR 1 Y f L E MOTOR 2 WHITE DOWN LIMIT CLOCKWISE LESS DOWN TRAVEL COUNTERCLOCKWISE MORE DOWN TRAVEL TOP VIEW AUDIENCE SIDE LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Da Lite Screen Company Inc warrants its products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damag
7. peat until the desired position is set SCREEN DOES NOT DROP ENOUGH Left motor as viewed from audience side Turn the white limit switch screw counterclockwise to increase the amount of fabric drop Right motor as viewed from audience side Turn the yellow limit switch screw counterclockwise to increase the amount of fabric drop After adjusting the limit screws on both motors run the screen down to test the stop position Repeat until the desired position is set Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller SETTING THE UP LIMIT POSITION SCREEN TRAVELS UP TOO FAR Left motor as viewed from audience side Turn the yellow limit switch screw clockwise to decrease the amount of travel Right motor as viewed from audience side Turn the white limit switch screw clockwise to decrease the amount of travel After adjusting the limit screws on both motors run the screen up to test the stop position If the screen travels up too far the safety stop switch will be activated and all power to the motors will be shut off You will have to deactivate the switch by hand To do this push down on the switch trigger see Figure 1 to release the switch and have someone run the screen down This safety switch is to prevent the screen from traveling too far and binding the motors should the motor limit switches fail SCREEN DOES NOT TRAVEL UP FAR ENOUGH Left motor as viewed
8. reen Standard Duty Cycle 1 MIN 30 SEC ON 45 MIN OFF AM cautioni Excessive continuous operation may cause overheating and motors will shut off Let motors cool 10 to 15 minutes and continue test Check the cables to make sure they are winding on the motor and roller pulleys properly SCREEN ADJUSTMENT 1 With screen in complete unrolled position examine the screen surface carefully If fabric does not hang flat loosen the nuts on the eyebolts of the black clamps Adjust the wingnuts to pull or relax the fabric as needed Several clamp heights may be adjusted depending on the severity of the hang After adjustment tighten the nuts against the underside of the frame Caution stage hands and others to check area before lowering screen Do not bump screen with ladders scenery etc MOTORIZED SCENIC ROLLER INSTALLATION BROWN OUTOF 4 COMMON BED UP BLACK DOWN GREEN GRO WHITE COMMON CONTROLLER RED OUT O CONTROLLER SAFETY SWITCH POWER INPUT WHITE COMMON BLACK HO 120VAC 60HZ GREEN GROUNDS A RED UP BLACK DOWN NN 9 NI RED OUT OF CONTROLLER BROWN OUT OF CONTROLLER BLUE COMMON BROWN DOWN NOTES REEN YELLOW GROUND 1 FUSE RATED 15A 250VAC BROWN OUT OF BLUE COMMON CONTROLLER SAFETY SWITCH RED OUT OF CONTROLLER POWERINPUT BLUE COMMO 240VAC 50Hz BROWN HOT WHIT
Download Pdf Manuals
Related Search