Home

Da-Lite Cosmopolitan Electrol 50" x 80"

1. PUSH THE STOP BUTTON 6 When the screen is in the desired up position slide the 3 position switch to the off center position The up limit Switch is now set 7 To test limit switch setting make sure the 3 position switch is in the off center position Press and release the up or down button on the wall switch to operate the screen 8 Replace switch and cover plate on the wall NOTE If stop button is pressed the wall switch will reverse direction To correct this press the stop button again This will reset the switch You will have to re set both the up and the down settings IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 4 conductor connection that is accessible TROUBLESHOOTING Visit www da lite com products tutorials php to find installation and troubleshooting tutorials You will also find a link to Live Chat for interactive support and you can contact us by email at info da lite com or by phone at 800 622 3737 or 574 267 8101 with any troubleshooting questions SYMPTOM 1 Screen will not operate Motor does not hum Motor hums 2 Incorrect stopping position in downward direction 3 Incorrect stopping position in upward direction 4 Noise NOTE Screen will operate with a low pitched hum 5 Coasting 6 Roller displaced from mounting bracket RESTORING
2. Use 2 conductor 20 24 gauge wire to extend the low voltage connection from the projector s 5 or 12 volt screen trigger output to the length required to reach the VPI When extending the low voltage connection FRONT OF BACK OF A P WALL SWITCH WALL SWITCH from the projector s screen trigger output polarity does not matter The red and black wires from the VPI are interchangeable IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments GREEN TEROUNDI EVEN if a third party control system is used Therefore it is advised to c VOLT SCREEN MODULE wire the switch or provide a 3 conductor connection that is accessible TRIGGER ON PROJECTOR BLACK HOT 7 WHITE COMMON GROUND MUST BE CONNECTED 3 conductor 20 24 gauge wire can be used in place of the supplied RJ 14 L Va TO BUILDING GROUND cable to connect the wall switch Connect the BUS terminals on the wall POWER INPUT 120VAC 60HZ PA Switch to the corresponding BUS terminals on the splitter board FIGURE 4 COSMOPOLITAN ELECTROL INSTALLATION RJ 14 PIN OUTS RJ 22 PIN OUTS 120V WIRING DIAG RAM TAB IS FACING UP TAB IS FACING UP WITH OPTIONAL BUILT IN LOW VOLTAGE CONTROL RJ 45 PIN OUTS RJ RJ 22 D P TAB IS FACING UP INPUTS RJ 45 RECEPTACLE RJ 45 JACK FRONT OF BACK OF WALL SWITCH WALL SWITCH POWER WIRE 3 conductor 20 24 gauge wire can be used in place of the supplied RJ 14 cable to connect the wall switch Connect th
3. methods of mounting to include Flush against wall Suspended from ceiling use extension brackets and Recessed above ceiling USE NO 6 BRACKETS TO HANG BEHIND CEILING HANGING CONCEALED ALLOW ROOM FOR ACCESS BEAM OR VALANCE WALL MOUNTED o o PICTURE SURFACE lt PICTURE PICTURE SURFACE E eae SURFACE SURFACE FIGURE 1 NOTE Under no circumstances should unit be completely sealed in recessed installation Allow access for service Picture surface is centered in case Case extends 4 beyond surface on either end Do not attach anything to screen slat rod or bottom fabric pocket Make sure screen is level Use a carpenter s level and plumb level CAUTION Do not cut wrapping paper or tape with knife or any sharp tool Remove by hand 2 Remove tape and rubber bands from slat pocket 3 Install electrical hook up that applies to your unit Make sure to review your Electrical Installation Checklists and wiring diagrams included for either 120 volt switch 220 240 volt switch or low voltage control 4 Testinstallation by running screen up and down a few times Be prepared to stop screen Standard Duty Cycle 1 MIN ON 3 MIN OFF NOTE Must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA C22 1 and the National Electric Code NEC NFPA 70 COSMOPOLITAN ELECTROL INSTALLATION Overall length A fabric width 8 Length B is the distance betw
4. one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA LITE S WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership Printed in U S A 7 46832 Rev 9 11
5. the up limit switch press and hold the up tactile button until the LED on back of switch turns solid green This will put the motor in limit set mode Turn the wall switch over and use the up button on front of switch Press and hold until the desired travel position is reached If you travel to far up you can press the down to move the screen downward If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen Once desired position is reached turn switch over press and hold up tactile button until the LED on back of switch blinks green twice The up limit is now set 5 To test limit switch setting press and release the up or down button on the wall switch to operate the screen 6 Replace switch and cover plate on the wall NOTE If the screen is in limit set mode and no buttons are pushed for 20 seconds the LED on the back of the wall switch will turn off the motor will return to run mode and no changes will be saved If this occurs return to step 3 for down limit adjustment or step 4 for up limit adjustment IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control RESINA used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible COSMOPOLITAN ELECTROL INSTALLATION CONNECT SUPPLIED RJ9 CABLE TO 240V WIRING DIAGRAM SWITCH OR USE 4 CABLE CONDUCTOR WITH OPTIO
6. to draw fabric over top 4 Remove tape and strap 6 LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Da Lite Screen Company Inc warrants its products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If itis necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the
7. LOST ROLLER WRAP 1 Push strap over back of roller 2 Tape end of strap to pocket CAUSE SOLUTION a Verify 115 125V or 220 240V If insufficient voltage rewire incoming electric line Replace fuse Reset circuit breaker Check above Tighten all loose wire connections Correct any improper connections Incorrect line voltage Blown fuse b Tripped circuit breaker c No power to operating switch or d junction Down Position Check for power across black and white leads Up Position Check for power across red and white leads Power at junction box Let motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace motor assembly NOTE Motor is a sealed assembly e Thermal overload tripped e f Broken wire in the up or down f position g Defective motor limit switch or g capacitor h Capacitor burned out h Replace motor assembly See instructions below See installation instructions a Lost roller wrap a b Down limit switch out of adjustment a Lost roller wrap a See instructions below b Up limit switch out of b Adjust up limit switch Call adjustment factory for instructions a Gear noise a Replace motor assembly a Defective brake a Replace motor assembly a Pin end slipped out of nylon a Realign pin end bracket bearing 3 Feed fabric as you pull strap
8. NAL BUILT IN OPTIONAL IR AND RF TO CONNECT TO SCREW TERMINALS LOW VOLTAGE WALL SWITCH LOW VOLTAGE CONTROL REMOTE CONTROL BLUE COMMON BROWN HOT GREEN 240VAC 50HZ 3 POSITION SWITCH RJ9 GROUND MUST BE CONNECTED TO C3 BUILDING GROUND GROUND TO CASE DRY CONTACTS ILT RJ9 PIN OUTS IMPORTANT NOTE The wall switch is REQUIRED to make any limit MEM switch adjustments EVEN if a third party control Rorup Fs system is used Therefore it is advised to wire the S Exe switch or provide a 4 conductor connection that is UN or DATA Eme accessible FIGURE 6 SCREEN ADJUSTMENT FOR 220V 240V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL 1 Remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate small 3 position switch on back of wall switch See Figure 6 3 To adjust the down limit switch slide the 3 position switch to the down position Press and hold the down button to run the screen down to the desired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON 4 When the screen is in the desired down position slide the 3 position switch to the off center position The down limit switch is now set 5 To adjust the up limit switch slide the 3 position switch to the up position Press and hold the up button to run the screen up to the desired stop position Release the button to stop the screen DO NOT
9. The Da Lite Difference Ee DA LITE PO a i DA LITE SCREEN COMPANY INC Instruction Book for 3100 North Detroit Street Post Office Box 137 COSMOPOLITAN ELECTROL Warsaw Indiana 46581 0137 Phone 574 267 8101 For Sizes Up To 9 x12 800 622 3737 Fax 574 267 7804 Toll Free Fax 877 325 4832 www da lite com e mail info da lite com IMPORTANT SAFETY INSTRUCTIONS When using your video equipment basic safety precautions should always be followed including the following 1 Read and understand all instructions before using 2 Position the cord so that it will not be tripped over pulled or contact hot surfaces 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons SAVE THESE INSTRUCTIONS PRE INSTALLATION 1 Carefully unpack screen and remove outer wrapping from case 2 Do not remove black tape or rubber bands from slat pocket 3 Always handle screen in horizontal position INSTALLATION There are three
10. e BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board IMPORTANT NOTE GREEN GROUND il The wall switch is REQUIRED to make any limit switch BLACK HOT j adjustments EVEN if a third party control system is WHITE COMMON GROUND MUST BE used Therefore it is advised to wire the switch or NA ND FIGURE 5 provide a 3 conductor connection that is accessible POWER INPUT 120VAC 60HZ SCREEN ADJUSTMENT FOR 120V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL OR VPI 1 Locate the wall switch and remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate the two tactile buttons on the back of the switch They are square silver with black round buttons See Figure 4 VPI or Figure 5 LVC for diagram 3 Toadjust the down limit switch press and hold the down tactile button until the LED on back of switch turns solid red This will put the motor in limit set mode Turn the wall switch over and use the down button on front of switch Press and hold until the desired travel position is reached If you travel to far down you can press the up to move the screen upward If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen Once desired position is reached turn switch over press and hold down tactile button until the LED on back of switch blinks red twice The down limit is now set 4 To adjust
11. een wall mounting holes at back of end caps and is the fabric width 6 1 2 3 4 DIAMETER HOLE FOR WALL INSTALLATION MOTOR END FABRIC HEIGHT x WIDTH AS ORDERED UP TO 12 FEET x 12 FEET FIGURE 2 WIRING ENCLOSURE COVER 120V WIRING DIAGRAM TO JUNCTION BOX MOUNTED IN SCREEN CASE IN WHICH INTERNAL WIRING TERMINATES IN WHITE DOWN WHITE LIMIT SWITCH ADJUSTMENT z S o OPERATING SWITCH AND N MULTIPLE CONTROL BLACK WITH PLATE FURNISHED WITH INSTALLATIONS THIS i YELLOW SCREEN SPDT WITH SWITCH IS REPLACED BY CENTER OFF l THE LOW VOLTAGE CONTROL OPERATED FROM PUSH BUTTON STATIONS SIDE view OF SWITCH AND BOX FIGURE 3 NOTE A single switch cannot be used to operate more than one screen Contact the factory for further information Sy 12 32 _ ft qua 32 DIAMETER FOR CEILING INSTALLATION I ENCLOSURE COVER 7 DIAMETER KNOCK OUT 7 DIAMETER OPENING FOR ELECTRICAL FITTINGS PICTURE SURFACE 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram included in wall switch box included with screen SCREEN ADJUSTMENT FOR SCREENS WITHOUT A BUILT IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are prope
12. rly adjusted at DA LITE Should it be necessary to adjust for more or less picture drop viewing area proceed in the following manner NOTE Use screwdriver or 5 32 Allen wrench to make adjustments SETTING THE DOWN LIMIT POSITION TO REDUCE SCREEN DROP Turn the white limit switch screw Figure 3 clockwise to decrease the amount of screen drop Run the screen down to test the stop position If the screen drops too far raise the screen about one foot and adjust the limit switch again Repeat until the desired position is set TO INCREASE SCREEN DROP Turn the white limit switch screw counterclockwise to increase the amount of screen drop Run the screen down to test the stop position If the screen does not drop enough raise the screen about one foot and adjust the limit switch again Repeat until the desired position is set Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller CAUTION Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller This screen comes standard with 0 or 2 black at the top See the specification data sheet for details COSMOPOLITAN ELECTROL INSTALLATION 120V WIRING DIAGRAM WITH PLI T Ni dd OPTIONAL BUILT IN VIDEO PR EET 2 INN ee E PROJECTOR INTERFACE A epu CAUTION THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR FAILURE TO DO SO MAY DAMAGE THE CONTROLLER

Da-Lite Cosmopolitan Electrol 50" x 80"

Contents

Download Pdf Manuals

Related Search

Related Contents

Da-Lite Cosmopolitan Electrol 50&quot; x 80&quot;

Contents

Download Pdf Manuals

Related Search

Related Contents

Da-Lite Cosmopolitan Electrol 50" x 80"