AOC 919VWA
Contents
1. auto adjusts the brightness of the screen so users can see the darker areas of the displayed content in more depths By increasing the darkness of the dark areas and the brightness of the bright areas contrast ratio is uplifted to exceed 10000 1 DCR value varies subject to the original CR values of the LCD module The higher the original CR the higher DCR can be achieved DCR is great for watching movie or video contents How to Use DCR Go to the first OSD icon labeled Luminance turn on or off DCR as desires DCR boosts the contrasts between lightness amp darkness and enables the viewer to see more layers and details of the picture especially in the darker areas Please note when DCR is on DCB will be disabled Disclaimer DCR aftereffects are subject to the resolution and quality of the display content hence may look different than the above illustrations Luminance dust Range Description Brightness 0 100 Backlight Adjustment Contrast 1 00 Contrast from Digital register Standard Mode Standard jr g Eco mode Internet Mode Internet a Game Mode Game 9 Movie Movie Mode i Sports Mode Gamma djust to Gamma amma2 Adjust to Gamma 2 amma3 Adjust to Gamma 3 amma g o oO Disable dynamic contrast ratio J CR Enable dynamic contrast ratio Adjust picture Clock to reduce Vertical Line noise Adjust Picture Phase to reduce Horizontal Line noise Adjust t2. grounded power outlet as a safety feature If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug e Unplug the unit during a lightning storm or when it will not be used for long periods of time This will protect the monitor from damage due to power surges Do not overload power strips and extension cords Overloading can result in fire or electric shock e Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor e Do not attempt to service the monitor yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all servicing to qualified service personnel e To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC Min 5A The wall socket shall be installed near the equipment and shall be easily accessible e For use only with the attached power adapter Output 12Vdc which have UL CSA listed license Only for monitors with power adapter e Please make sure to clean the cabinet regularly with the provided cloth you can use soft cleanser to clean the stain instead of severe spray cleanser which will cauterize the monitor cabinet e Dont leak liquid int
3. specified in this documentation may result in exposure to shock electrical hazards and or mechanical hazards Read and follow these precautions when connecting and using your computer monitor PRECAUTIONS e Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement e Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions e Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided e The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company e The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin This plug will fit only into a
4. the red and yellow colors are enriched automatically thus presents human skin with more natural and truer colors Natural Skin setting is ideal for viewing human portrait and detailed skin texture ON Green Field When Green Field is turned on the green color is enriched so that football field and mountain landscape would look more natural and fresh Green Field setting is ideal for watching mountain scenery and outdoor sports ON OFF Sky Blue When Sky Blue is turned on the color blue is being fine tuned so that the sky or ocean landscape will look more vivid and in depth Sky Blue setting is ideal for viewing sky and ocean images OFF Demo Screen divided into two for demonstration purposes 2 How to use Picture Boost Users can change the color settings of a self selected zone on the screen The size and position of the selected zone can also be adjusted Picture Boost is located in the fifth icon labeled Picture Boost in the OSD menu Turn on Bright Frame to select a zone on the screen to be enhanced Please note when adjust or turn on any one of the DCB features the rest of color settings including DCR will be disabled or return to default Disclaimer DCB aftereffects are subject to the resolution and quality of the display content hence may look different than the above illustrations DCR Adjustment Dynamic Contrast Ratio What is DCR Dynamic Contrast Ratio DCR
5. 919Vwa User s Manual About This Guide This guide describes the monitor s features setup and operation Information in this document is subject to change without notice The sections are as follows Safety Instructions lists safety information Setup describes the initial setup process Using the Monitor gives an overview of how to use the monitor Drivers provides driver installation instructions for Windows Technical Support provides tips and solutions for common problems Product Information lists the technical specifications of the monitor Warranty Statement Warranty Statement used in Europe National Conventions The following subsections describe notational conventions used in this document Notes Cautions and Warnings Throughout this guide blocks of text may be accompanied by an icon and printed in bold type or in italic type These blocks are notes cautions and warnings and they are used as follows E NOTE A NOTE indicates important information that helps you make better use of your computer system CAUTION A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the l problem fr WARNING A WARNING indicates the potential for bodily harm and tells you how to avoid the problem Some warnings may appear in alternate formats and may be unaccompanied by an icon In such cases the specific presentation of the warning is mandated by regulatory authority Produc
6. Only for the models with speakers e Source hot key When the OSD is closed press Auto Source button will be Source hot key function Only for the models with dual or more inputs Press Source button continuously to select the input source showed in the message bar press Menu Enter button to change to the source selected e Auto configure hot key When the OSD is closed press Auto Source button continuously about 2 second to do auto configure DCB Adjustment Dynamic Color Boost What is DCB Dynamic Color Boost DCB is an advanced color adjustment technology Through analyzing RGB signals DCB creates more vivid and natural images to suit various color environment needs DCB has two types of color enhancers Color Boost and Picture Boost i vi ICM Color Adjustment signal Input Analysis DCC Dynamic color control ICM Intelligent color management 1 How to use Color Boost Five color enhancement settings To accommodate various display needs Color Boost also offers 5 different color enhancement modes Full Enhance Natural Skin Green Field Sky Blue and Auto Detect Please go to the fourth icon labeled Color Boost in the OSD menu and select one of the five settings you desire to be turned on Full Enhance When Full Enhance is turned on the color saturation of the entire screen is fully enriched thus all colors become more vibrant Nature Skin When Natural Skin is turned on
7. Version 1 0 2007 12 20 Copyright AOC Monitors 2008 ti Email S00 gpaec com http www aoc com Compatibility i menu supports major graphic cards of ATI Nvidia Intel VIA S3 Please contact with us if your graphic card was not supported i menu software Specifications Model number 919Vwa Driving system TFT Color LCD lewable Image Size 481mm diagoanl LCD Panel Pixel pitch 0 2835mm H x 22S oN Video R G B Analog Interface amp Digital Interface Separate Sync H V TTL Display Color 16 7M Colors Dot Clock 135 MHz Horizontal scan range 30 kHz 83 kHz Horizontal scan Size Maximum gl Vertical scan range 55 Hz 75 Hz ertical scan Size Maximum am Optimal preset 1440 x 900 60 Hz resolution Resolution Highest preset Ecolution 1440 x 900 75 Hz lug amp Play VESA DDC2B Cl D Sub 15pin amp DVI D Analog 0 7Vp p standard 75 OHM Positive amp DVI D Digital Interface TMDS 00 240VAC 50 60Hz Active lt 37 W tandby lt 2 W x 1W 5 pin Mini D Sub amp DVI D ignal Cable Type Detachable imensions amp Weight ower Source Power Consumption peakers onnector Type Ul DOA UF a te O O CIC lt 9 O15 Old Ia Q O ei ie D Height with base 365 mm Physical Characteristics Width 489mm eight monitor only 2a Temra Operaing poao Humidity TT Environmental Operating 10 to 85 non condensing Non Operating 5 to 80 non condensin
8. all Mounting Arm Preparing to Install An Optional Wall Mounting Arm ie A BR l ee ree haf ak Te ae ER s ef nf 4 FA AA pra pri J i od 7 a wie E a ati oe cf are ee gree ea PSI Toe ell 1 a This monitor can be attached to a wall mounting arm you purchase separately Disconnect power before this procedure Follow these steps 1 Remove the base 2 Follow the manufacturer s instructions to assemble the wall mounting arm 3 Place the wall mounting arm onto the back of the monitor Line up the holes of the arm with the holes in the back of the monitor 4 Insert the 4 screws into the holes and tighten 5 Reconnect the cables Refer to the user s manual that came with the optional wall mounting arm for instructions on attaching it to the wall Noted VESA mounting screw holes are not available for all models please check with the dealer or official department of AOC Distance between the wall mount holes 100 x 100 mm Screw specification for wall mount M4 x 10 Setting the Optimal Resolution The recommended resolution for this monitor is 1440 by 900 To setup the monitor to this resolution follow the steps below oo AY Click START Click SETTINGS Click CONTROL PANEL Double click DISPLAY Click SETTINGS Set the resolution SLIDE BAR to 1440 by 900 External Controls Press the power button to turn the monitor on or off The other control knobs are locat
9. ed at front panel of the monitor See Figure By changing these settings the picture can be adjusted to your personal preferences The power cord should be connected Press the power button to turn on the monitor The power indicator will light up 1 Source Auto Exit 2 Eco mode 3 Volume 4 Menu Enter 5 Power Button amp Indicator OSD Settings Press the MENU button to activate the OSD window Press or to navigate through the functions Once the desired function is highlighted press the MENU buttonto activate it If the function selected has a sub menu press or again to navigate through the sub menu functions Once the desired function is highlighted press MENU button to activate it Presst or to change the settings of the selected function To exit and save select the exit function If you want to adjust any other function repeat steps 2 3 OSD Lock Function To lock the OSD press and hold the Menu button while the monitor is off and then press power button to turn the monitor on To un lock the OSD press and hold the Menu button while the monitor is off and then press power button to turn the monitor on Eco Mode hot key Press the Eco key continuously to select the Eco mode of brightness when there is no OSD Eco mode hot key may not be available in all models Volume adjustment hot key When there is no OSD press Volume to active volume adjustment bar press or to adjust volume
10. g Mies POSS Operating 0 3000m 0 10000 ft Non Operating 10 5000m O 15000 ft EPA ENERGY STAR ENERGY STAR ENERGY STAR is a U S registered mark s an ENERGY STAR Partner AOC International Europe GmbH has determined that this product meets the ENERGY STAR guidelines for energy efficiency Preset Display Modes HORIZONTAL VERTICAL FREQUENCY kHZ FREQUENCY Hz Pp 1280x1024 BO 1440j 900 Pin Assignments H sync TMDS Data 2 4 Shield MDS Data 1 3 Shield Pinno Signal Name Pin No E MDS Data 1 Signal Name TMDS Data 0 TMDS Clock Shield Ground for 5V TMDS Clock Plug and Play Plug amp Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The DDC2B is a bi directional data channel based on the 1 C protocol The host can request EDID information over the DDC2B channel End
11. he verticalposition of the picture Adjust the horizontal position of the picture Clock a o Phase H Position Position Recall Warm Color Temperature from EEPROM Recall Normal Color Temperature from EEPROM Recall Cool Color Temperature from EEPROM Recall SRGB Color Temperature from Normal Red Gain from Digital register reen Gain Digital register G jjs m im m zy O User Q Z TI D 3 Blue Gain from Digital register ull Enhance isable or Enable Full Enhance Mode ature Skin isable or Enable Nature Skin Mode reen Field Disable or Enable Green Field Mode Sky blue on or off Disable or Enable Sky blue Mode isable or Enable AutoDetect Mode Disable or Enable Demo on or off emo on or off 4 100 100 100 100 100 on or off rame Size rightness ontrast Adjust Frame Size Adjust Frame Brightness djust Frame Contrast Adjust Frame horizontal Position Adjust Frame vertical Position Disable or Enable Bright Frame position position right Frame i gt 100 100 Position Position Timeout djust the verticalposition of OSD Adjust the horizontal position of OSD Adjust the OSD Timeout OO e WIG N o OO oO o lja TT JS ola l l a ES A A A L JJ L O W TI JE o UO OD D Q y N Transparence 0 100 Adjust the transparence of OSD anguage a the 080 language Auto elect to Auto Detect inpu
12. mma 3 i gt i gt CO Co u lt Q D O Q S lt a o 3 A 5 D D D S ej 3 a a a D D D D o D Disable dynamic contrast ratio Enable dynamic contrast ratio Reset the current page Remarks 1 If DCR is set to on the other 4 items of Luminance cannot be adjusted 2 If anyone of DCR Color Boost and Bright Frame of Picture Boost is set to on the others are set to off automatically 3 The Brightness and Contrast can be adjusted only when Eco mode is on standard mode 2 Image setup Glock oat LM H Position mics ESZUK ii Phase v Position Image Setup o A Image Setup Adjust Range Description Warm r User Mode Normal E User R Cool User G sRGB Recall Warm Color Temperature from EEPROM Recall Normal Color Temperature from EEPROM Recall Cool Color Temperature from EEPROM Recall SRGB Color Temperature from EEPROM Red Gain from Digital register Green Gain Digital register Blue Gain from Digital register Reset the menu to default Remarks 1 When User is chosen you can change the monitor color to your desired color by setting the value of R G B 2 When SRGB is chosen the Brightness Contrast and Gamma can not be adjusted 4 Color Boost Full Enhance Ei Nature Skin Sky biue Green Field Auto Detoct Demo aa m Enhance prorat isblsarEnsb Ful Enhance Made or Enable Full Enhance Mode Sh Skin moro
13. o monitor which will result in the damage of chassis or component Please unplug before cleaning and do not scratch the screen with hard things Setup the stand and base Please setup or remove the base following below steps Adjusting Viewing Angle e For optimal viewing it is recommended to look at the full face of the monitor then adjust the monitor s angle to your own preference Hold the stand so you do not topple the monitor when you change the monitor s angle e You are able to adjust the monitor s angle from 5 to 20 5 og TX NOTE Do not touch the LCD screen when you change the angle It may cause damage or break the LCD screen Attaching the Cables Cable Connections On Back of Monitor and Computer 1 Power 2 DVI 3 Analog 4 Audio Turn off your computer before performing the procedure below 1 Connect the power cable to the AC port on the back of the monitor Connect one end of the 15 pin D Sub cable to the back of the monitor and connect the other end to the computer s D Sub port 3 Optional C Requires a video card with DVI port Connect one end of the 24 pin DVI cable to the back of the monitor and connect the other end to the computer s DVI port 4 Connect the audio cable to audio in port on the back of the monitor 5 Turn on your monitor and computer If your monitor displays an image installation is complete If it does not display an image see Troubleshooting Attaching W
14. t Registration Please link www aoc com select your country or region log in Product Registration to register FCC Notice FCC Class B Radio Frequency Interference Statement WARNING FOR FCC CERTIFIED MODELS NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help NOTICE 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded in
15. t ia or Enable Nature Skin Mode Green Field on or off Disable or Enable Green Field Mode Sky blue on or off Disable or Enable Sky blue Mode Disable or Enable Demo Reset the menu to default Remarks 1 There is only one item can be set to on except Demo If you set any item to on the others are changed to off automatically 2 If anyone of DCR Color Boost and Bright Frame of Picture Boost is set to on the others are set to off automatically 5 Picture Boost BrightFrame 4 Frame Size a Brightness 5 H Position P Contrast oa TI V Position Remarks 1 Only when Bright Frame is set to on the other 5 items can be adjusted 2 If anyone of DCR Color Boost and Bright Frame of Picture Boost is set to on the others are set to off automatically 6 Settina Options Ej Auto run when eyatem slaris Program languages ESNE Ci Display Moda Configuration file r E Wf Show alerts and hints i Turn on hotkeys rogramm language Geete programm language 7 Extra Pivot I BestResolution Reso Auto Config Ej Ea Re scan pm h 40 180 270 degree pivot image Reset the morutor settings to the factory defaults Tore scan Plug and Play morutor Hest resolution po Select display resolution from preset mode Auto Contig Auto adjust the picture to default About l menu
16. t signal Input Select elect Analog Sigal Source as Input igital Select Digital Sigal Source as Input Auto Config es or no Auto adjust the picture to default mage Ratio ide or 4 3 Select wide or 4 3 format for display DC Cl es or no Turn ON OFF DDC CI Support Show the information of the main Information l image and sub image source Reset yes or no Reset the menu to default Exit the main OSD Notes 1 If the product has only one signal input the item of Input Select is disable to adjust 2 If the product screen size is 4 3 or input signal resolution is wide format the item of Image Ratio is disalbe to adjust 3 One of DCR Color Boost and Picture Boost functions is active the other two function is turned off accordingly LED Indicators LED Color Green or Blue How to use i menu software Installation Welcome to use i menu software by AOC i menu makes it easy to adjust your monitor display setting by menus on the screen instead of OSD button on the monitor Please click here to setup the software To complete installation please follow the installation guide Using i menu 1 Luminance P Contrast eee F e Brightnoss Gamma d Gamma P A Eco Mode DCR Ej Contrast 0 100 Contrast from Digital register Brightness 0 100 Backlight Adjustment Standard Internet Mode Internet Movie Gamma1 amma2 amma3 ff Adjust to Gamma djust to Gamma 2 djust to Ga
17. terface cables and AC power cord if any must be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is theresponsibilities of the user to correct such interference WEEE Declaration Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or the shop where you purchased the product HG Declaration C9 arETY Lamp Disposal LAMP S INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL STATE OR FEDERAL LAWS FOR MORE INFORMATION CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW EIAE ORG Precautions g WARNING Use of controls adjustments or procedures other than those
Download Pdf Manuals
Related Search