Home

Philips 247E3LSU

1. gt One lit red green or blue sub pixel a N i P Two adjacent lit sub pixels Red Blue Purple Red Green Yellow Green Blue Cyan Light Blue N Ne 4 Three adjacent lit sub pixels one white pixel amp Note Proximity of Pixel Defects A red or blue bright dot must be more than 50 Because pixel and sub pixels defects of the percent brighter than neighboring dots while same type that are near to one another may be a green bright dot is 30 percent brighter than more noticeable Philips also specifies tolerances neighboring dots for the proximity of pixel defects a Black Dot Defects z 2 Black dot defects appear as pixels or sub pixels that are always dark or off That is a dark dot is a sub pixel that stands out on the screen when the monitor displays a light pattern These are E the types of black dot defects a N a a B Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period a TFT Monitor panel in a Philips flat panel C J monitor must have pixel or sub pixel defects E J exceeding the tolerances listed in the following tables BRIGHT DOT DEFECTS ACCEPTABLE LEVEL it subpixel 2 adjacent lit subpixels 3 adjacent lit subpixels one white pixel Doa V Distance between two bright dot defects 215mm Total bright dot defects of all
2. Contact Information for NORTH AMERICA Country Call center ASC Consumer care number CILE 23 Contact Information for APMEA region Country Call center ASC Consumer care number AGOS NETWORK PTY LTD _ 1300 360 386 New Zealand Visual Group Ltd 0800 657447 Hong Kong mong Kone lek 652 2617 9637 Smart Pixels Technology Ltd Macau Tel 853 0800 987 le BU 75 6376 PT Gadingsar elektronika Prima s e O YNA PE Ole Cree Lidl 080 600 6600 After Market Solutions CE Singapore Taiwan Thailand South Africa United Arab Emirates Israel Vietnam Philippines Sri Lanka Bangladesh Nepal Cambodia Philips Consumer Service 9221 2737411 16 Philips Electronics Singapore Bie KEMER e onsumem Gare 6 0827 Center REGY Teleservices FESC 99022309099 Taiwan Axis Computer System Co Ltd 662 934 5498 Sylvara Technologies Pty Ltd 086 0000 888 ALSFHARBDCOMPOWER EEG 00971 42276525 Eastronics LID 1 800 56 000 10488222007 ree Cin inn ety 84 5113 562666 Danang City 84 5113 562666 Can tho Province 02655 4599 10 34 Glee Electronics Inc 02 637 6559 to 60 FPT Service Informatic Company Ltd no distributor and or service provider currently Distributor Computer source 9680 229 1141747 912759 Ltd warranty buy out 880 2 8128848 52 Distributor Syakar Co Ltd 977 1 4222395 warranty buy out Distributor Neat Technology Pte Ltd Singapore warranty 855 023 9
3. Power LED I Over Scan H Position V Position Phase Clock Resolution Notification I Reset L_ Information 0 100 0 100 Off 1 2 3 4 5s 10s 20s 30s 60s 0 1 2 3 4 On Off available for selective models 0 100 0 100 0 100 0 100 On Off Yes No EJ Resolution notification This monitor is designed for optimal performance at its native resolution 1920x1080Q060Hz When the monitor is powered on at a different resolution an alert is displayed on screen Use 1920x1080Q60Hz for best results Display of the native resolution alert can be switched off from Setup in the OSD On Screen Display menu EJ Physical Function Tilt PHILIPS 2 3 Remove Base Stand EB Remove the Base Stand Before you start disassembling the monitor base please follow the instructions below to avoid any possible damage or injury 1 Place the monitor face down on a smooth surface taking care to avoid scratching or damaging the screen 2 Detach the base stand away from the base column by 1 Use your fingers to loosen the screw located at the bottom of the base 2 Gently move up and down to release the latch that locks the base and pull the base away from the base column 3 lmage Optimization 3 1 Smartlmage Lite EB What is it Smartlmage Lite provides presets that optimize display for different types of con
4. Eee x er s le SS i S D 3 o eo KB H o Ov Teils Q C power input VGA input Q DVI D input Kensington anti theft lock Q AC power input Model 247E3LH VGA input HDMI input HDMI audio output Kensington anti theft lock PHILIPS Connect to PC 1 Connect the power cord to the back of the monitor firmly 2 Turn off your computer and unplug its power cable i 3 Connect the monitor signal cable to the 90 video connector on the back of your O computer AS O 4 Plug the power cord of your computer and AC power input your monitor into a nearby outlet VGA input 5 urn on your computer and monitor If the HDMI input monitor displays an image installation is Audio input complete Q Audio output Kensington anti theft lock 2 2 Operating the monitor EJ Front view product description Model 247E3L ld amp 3 OK 00 Switch monitor s power ON and Model 247E3LH Switch monitors power ON and o O OFE amp OK Access the OSD menu 4 Return to previous OSD level Adjust the speaker volume AW Adust the OSD menu
5. gt Go to www philips com welcome to download the latest version of monitor driver Philips SmartControl System support and requirements 1 System support Windows 7 Vista XP 2 Language support English German Spanish French kalian Russian Portuguese Simplified Chinese 3 Philips Monitor Plug and Play support gt Go to http www portrait com dtune phl enuindex html to download the latest version of SmartControl software First launch Wizard he first time after installation of SmartControl Lite rt will automatically go to Wizard for first time launch he wizard will guide you through adjustment your monitor performance step by step e You can go to Plug in menu to launch wizard later on as well e You can adjust more options without wizard by Standard pane W SmartControl 2x SmartControl Lite PHILIPS Wizard Adjust Audio Color Input Options Presets wa e Multi Monitors Help Start Wizard FJ Start with Standard pane Adjust menu Adjust Menu allow you to adjust Brightness Contrast Focus Positlon and Resolution You can follow the instruction and do the Cancel prompts user If you want to cancel adjustment installation W SmartControl SmartControl Lite Position Kd Resolution W SmartControl SmartControl Lite y Brightness e A Focu Position Resolution s PHILIPS Brightness Improper y adjusted Brightness will result i
6. Change the signal input source Smartlmage Lite There are three ED modesto be selected Standard Internet and Game Model 247E3LPH A SENSOR amp OK 00 Switch monitors power ON and l o O OFE E OK Access the OSD menu 4 Return to previous OSD level o gt Change display format Adjust the brightness level AW Adjust the OSD menu Change the signal input source fk Change display format Smartlmage Lite There are three ED modesto be selected Standard Internet and Game o O OFR amp OK Access the OSD menu Q 4 Return to previous OSD level O sean o IE AW Adjust the OSD menu Change the signal input source Smartlmage Lite There are three ED modesto be selected Standard Internet and Game 9 Description of the On Screen Display What is On Screen Display OSD On Screen Display OSD is a feature n all Philips LCD monitors It allows an end user to adjust screen performance or select functions of the monitors directly through an on screen instruction window A user friendly on screen display interface is shown as below Model 247E3L SD Setting Model 247E3L for 1A model B gt Picture Format e Wide Screen icture gt gt Brightness OMIM 100 EN Contrast MII 50 Colo a_y SmartContrast Off Language
7. Position x iri PHILIPS Use the Position buttons to center the image on your display Using this tool you can position the image up down left or right 1 Use the Up Down buttons to center the image vertically 2 Use the Left Right buttons to center the image horizontally Undo Reset PHILIPS Resolution You are currently at a Preferred resolution For your display to show crisp clear text colors and images your display should be set to its Preferred resolution If your display is at a Non Preferred resolution click on the Preferred button to change your resolution to Preferred Enable Resolution Notifier Picture Format 4 3 aspect ratio Preferred Color menu Color Menu allow you to adjust RGB Black Level White Point Color Calibration and Smartlmage Lite Please refer to Smartlmage Lite section You can follow the instruction and do the adjustment Refer to below table for sub menu item base on your input Example for Color Calibration Wl SmartControl Ex SmartControl Lite PHILIPS Black Level Improperly adjusted Black Level will result in a loss of detail in darker image areas Adjust the Black Level for the best possible picture quality 1 Adjust the black level of the Red Green and Blue using the slider bars M RGB tit Red 50 Black Level Green 50 white Point F Blu 50 Display Gamma Options Ss u Undo Reset ap SmartImage W
8. Reduce use of primary materials Reduce use of toxic materials Avoid the disposal of hazardous waste EPEAT S requirement that all registered products meet ENERGY STAR s energy efficiency specifications means that these products will consume less energy throughout their life 25 CE Declaration of Conformity This product is in conformity with the following standards e EN60950 1 2006 Safety requirement of Information Technology Equipment e EN55022 2006 Radio Disturbance requirement of Information Technology Equipment e EN55024 1998 A1 2001 A2 2003 Immunity requirement of Information Technology Equipment e EN61000 3 2 2006 Limits for Harmonic Current Emission e EN61000 3 3 1995 A1 2001 A2 2005 Limitation of Voltage Fluctuation and Flicker following provisions of directives applicable e 2006 95 EC Low Voltage Directive 2004 108 EC EMC Directive e 2005 32 EC EuP Directive EC No 1275 2008 mplementing Directive for Standby and Off mode power consumption and is produced by a manufacturing organization on ISO9000 level The product also comply with the following standards 1 09241 307 2008 Ergonomic requirement Analysis and compliance test methods for electronic visual displays e GS EK1 2000 2009 GS mark requirement prEN50279 1998 Low Frequency Electric and Magnetic fields for Visual Display MPRA MPR 1990 8 1990 10 Low Frequency Electric and Magnetic fields T
9. pm OSD Settings Model 247E3LH VGA HDMI 1 HDMI2 Picture Qu T Model 247E3LPH 2 MLS aS Basic and simple instruction on the control keys In the OSD shown above you can press W A buttons at the front bezel of the monitor to move the cursor and press OK button to confirm the choice or change The OSD Menu Below is an overall view of the structure of the On Screen Display You can use this as a reference when you want to work your way around the different adjustments later on Main menu Sub menu Power Sensor On 9 eod Off available for selective models VGA Input r DVI available for selective models HDMI 1 available for selective models L HDMI 2 available for selective models Picture Format Wide Screen 4 3 Picture fr Brightness 0 100 Contrast 0 100 I SmartResponse On Off available for selective models SmartContrast On Off r Volume 0 100 available for selective models Audio Stand Alone On Off Mute Qn Off r Color Temperature 6500K 9300K Color sRGB User Define r Red 0 100 Green 0 100 Blue 0 100 Language English Espa ol Francais Deutsch Italiano Portugu s Pyccku fai NFA xc T rk e r Horizontal OSD Settings t Vertical Transparency OSD Time Out Setup nr Auto
10. a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help 26 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device To prevent damage which may result in fire or shock hazard do not expose this appliance to rain or excessive moisture THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS FCC Declaration of Conformity Declaration of Conformity for Products Marked with FCC Logo United States Only FC This device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Commission Federale de la Communication FCC Declaration amp Cet quipement a t test et d clar conforme auxlimites des appareils num riques de class B aux termes de l article 15 Des r gles de la FCC Ces limites sont concues de facon a fourir une protection raisonnable contre les interf rences nuisibles dans le cadre d une installation r sidentielle CET appareil produit utilise et peut
11. Hot key Sensor distance Gp v A SENSOR amp ok 5 EJ How to adjust settings If PowerSensor is not operating correctly inside or outside the default range here s how to fine tune detection e Press the PowerSensor hot key e You will find the default position 3 on the adjustment bar e Adjust the PowerSensor detection adjustment to Setting 4 and press OK e Test the new setup to see if PowerSensor properly detects you in your current position amp Note A manually selected PowerSensor mode will remain operational unless and until it is readjusted or the default mode is recalled If you find that the PowerSensor is excessively sensitive to nearby motion for some reason please adjust to a lower signal strength 18 5 Technical Specifications Monitor Panel Type MEEEBD Backlight BERD Panel Size Jee NS Gaal Aspect Ratio ley Pixel Prtch 00752027 Sam Brightness 300 cd m SmartContrast 20 000 000 1 Contrast Ratio typ 1000 Response Time typ 5ms SmartResponse 2ms available for model 24 E3LH 247E3LPH Optimum Resolution 1920x1080 60Hz Viewing Angle 170 H 160 V CR gt 10 178 H 170 V Q C R 5 Picture Enhancement Smartlmage Lite Signal Input Display Colors IZA Vertical Refresh Rate 56Hz 6Hz Horizontal Frequency 30kHz 83kHz sRGB eS DVI Digital VGA Analog HDMI available for model 247E3LH 247E3LPH Inpu
12. Input Voltage at enero ust Sa mailen 100VAC 5VAC 115VAC 5VAC 230VAC 5VAC 50Hz 3Hz 60Hz 3Hz 50Hz 3Hz Normal Operation typ 2 ISSN 17 53W Sleep typ 0 5W 0 5W 0 5W Off typ 0 3W 0 3W 0 3W AC Input Voltage at AC Input Voltage at AC Input Voltage at Heat Dissipation 100VAC 5VAC 115VAC 5VAC 230 VAC 5VAC 50Hz 3Hz 60Hz 3Hz 50Hz 3Hz Normal Operation ao Ad Har See lel UG 59 83 BTU hr Sleep dis SIR eee inte IERERE M Off TO BTO ing POET OD Oe TOE Power LED indicator On mode White Standby Sleep mode White blinking Power Supply Built in 100 240VAC 50 60Hz 247E3LPH On Mode typ 20 85W typ 23VV max AC Input Voltage at AC Input Voltage at AC Input Voltage at ADA ANC 100VAC 5VAC 115VAC 5VAC 230VAC 5VAC EnergyStar 5 0 test method 50Hz 3Hz 60Hz 3Hz 50Hz 3Hz Normal Operation typ WIA ROT 17 02W Sleep typ 0 5W 0 5W 0 5W Off typ 0 3W 0 3W 0 3W AC Input Voltage at AC Input Voltage at AC Input Voltage at Heat Dissipation 100VAC 5VAC 115VAC 5VAC 230VAC 5VACG 50Hz 3Hz 60Hz 3Hz S04 nior Normal Operation Seis ey TOE 58 16 BTU hr 23 07 ERU Sleep TETUA 1A sey pape T7 ERTO Off TOZ BTO TOZ B TONE TO ETOM 20 Power LED indicator On mode White Standby Sleep mode White blinking Power Supply Built in 100 240VAC 50 60Hz Product with stand WxHxD
13. O O O O ERRER x O O O O O FPA IGA PARR AAA NEE REL aR ERE RES O RTRA BA BAK TEZA TFSI HY BP RO Z CS E RFRETAPEREEWAOMREKIAE ERRERA F X RRA EH R W e IP RAMEN RARA E ETRA RHUBSEREMDELIDRE SCR UE NUEWOBIRER BEER x HBA FRFAMIAROHSIZA ER BT RAAB 29 9 conn EC SNR SPR AE ETF MER DAEA Sr 17 IL Bae TE IE B8 FH AR TTRZZEJMEBCCZ BT mW AHS fe I i ROGER EXT ER TROT AR JOP EN ae ti A ER BRERA REPHAR ERECTED ZDRAFAUTER EMRE CIN gt 108 BE ma GB 21520 2008 FMB SABA mg BESL ERR http www energylabel gov cn DER BERUFT te ART mE EHER Bernie VE JI T ETERRA HER gt ZH RES Panay angen EIN gt ISS RIAA BASH TT dul BA BEREAN NAZCA SH H ESTA RT RJ TEL USC i EE JT Pe ETT ILLAS BB o 8 Customer care and warranty 8 1 Philips Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products VVe use some of the industry s most advanced manufacturing processes and practice stringent quality control However pixel or sub pixel defects on the TFT Monitor panels used in flat panel monitors are sometimes unavoidable No manufacturer can guarantee that all panels will be free from pixel defects but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty his notice explains the diff
14. SIG AT NT Product without stand WxHxD 579 4 x 362 7 x 41 1 mm Product with stand 4 4 Kg Product without stand 4 03 kg Product with packaging 6 14 kg Temperature range operation OG er m Temperature range Non operation 20 C to 60 C Relative humidity 20 to 80 Operation 12 000ft 3 658m Regulatory Approvals aus Non operation 40000f 12 192m MTBF 30 000hrs ROHS YES Erg Silver www epeat net Packaging 10076 recyclable GE Mark FCC Glass B GOAST SEMK TEO Gertiied discum BoM Is o24 1 307 Color Black Back Black Blue tint Front Finish Glossy amp Note 1 EPEAT Gold or Silver is valid only where Philips registers the product Please visit www epeat net for registration status in your country 2 This data is subject to change without notice Go to www philips com support to download the latest version of leaflet 21 5 1 Resolution amp Preset Modes EB Maximum Resolution 1920x1080 60Hz analog input 1920x1080 60Hz digital input A Recommended Resolution 1920x1080 60Hz digital input amp Note Please notice that your display works best at native resolution of 1920x1080Q60Hz For best display quality please follow this resolution recommendation 22 The following setup is used to measure power consumption on this monitor 6 Power Management If you have VESA DPM compliance display card e Native reso
15. The following subsections describe notational conventions used in this document Notes Cautions and Warnings Throughout this guide blocks of text may be accompanied by an icon and printed in bold or italic type These blocks contain notes cautions or warnings They are used as follows amp Note This icon indicates important information and tips that help you make better use of your computer system Caution This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data N Warning This Icon Indicates the potential for bodily harm and tells you how to avoid the problem Some warnings may appear in alternate formats and may not be accompanied by an icon In such cases the specific presentation of the warning is mandated by the relevant regulatory authority 1 3 Disposal of product and packing material Waste Electrical and Electronic Equipment WEEE This marking on the product or on its packaging illustrates that under European Directive 2002 96 EC governing used electrical and electronic appliances this product may not be disposed of with normal household waste You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection To determine the locations for dropping off such waste electrical and electronic contact your local government office the waste disposal organization that serves your household
16. a non supported display capable of DDC CI only the Help and Options tabs are avallable W SmartControl SmartControl Lite Adjust User Manual Update Color a Display ID System ID Version x PHILIPS Version SmartControl Version 0 00 EVALUATION dtune plp R2009 12 17 1913 04 DDC CI Communication Yes ATI2 API Copyright 1993 2009 Portrait Displays Inc Context Sensitive menu The Context Sensitive menu is Enabled by default If Enable Context Menu has been checked in the Options Preferences pane then the menu will be visible SmartControl gt Te n EN SmartControl Select Preset gt Tune Display The Context Menu has four entries e SmartControl Lite When selected the About Screen is displayed e Select Preset Provides a hierarchical menu of saved presets for immediate use A check mark shows the currently selected preset Factory Preset can also be called from the drop down menu e Tune Display Opens the SmartControl Lite control panel e Smartlmage Lite Check current settings Standard Internet Game Task Tray Menu Enabled The task tray menu can be displayed by right clicking on the SmartControl Lite icon from the task tray Left Click will launch the application Help Technical Support Check For Update About The task tray has five entries e Help Access to User Manual file Open User Manual file using the default browser window e Technica
17. display EXIT Run at Startup is checked On by default When disabled SmartControl Lite will not launch at start or be in the task tray The only way to launch SmartControl Lite is either from the desktop short cut or from the program file Any preset set to run at startup will not load when this box is unchecked Disabled Enable transparency mode Windows Vista XP Default is 076 Opaque display capable of DDC CI only the Help and Options tabs are available Options gt lnput Will only be active when selecting Input from the drop down Options T4 menu On a non supported display capable of DDC CI only the Help and Options tabs are available All other SmartControl Lite tabs are not available W SmartControl SmartControl Lite n Adjust Audio Auto Pivot Input Wizard Presets wa Multi Monitors ux PHILIPS Input Your display has two inputs connections on back of this display so you can hook up two different sources at the same time Use the Analog In and Digital In buttons to select which source you d like to view You are currently viewing the analog in image IMPORTANT If you switch inputs SmartControl may lose the ability to control your monitor In this case you may have to use the Input Select button on the front of your monitor to switch back to the original input before SmartControl functionality can be restored Analog In Digital In e Display the Source instructi
18. functions worked well before but it does not work anymore what can do If the following actions were executed the monitor driver may need to be re installed e Changed video graphic adapter to another one e Updated video driver e Activities on OS such as service pack or patch e Run Windows Update and updated monitor and or video driver e Windows was booted with the monitor power off or disconnected e To find out please right click My Computer and click on Properties gt Hardware gt Device Manager e If you see Plug and Play Monitor shows under Monitor then you need to re install Simply remove SmartControl Lite and re install it Q3 After installing SmartControl Lite when clicking on SmartControl Lite tab nothing shows up after a while or a failure message shows what happened It might be your graphic adaptor is not compatible with the SmartControl Lite If your graphic adaptor is one of the above mentioned brands try to download the most updated graphic adaptor driver from Q4 Ans Q5 Ans corresponding companies web site Install the driver Remove SmartControl Lite and re install it once more If it is still not working we are sorry that the graphic adaptor is not supported Please visit Philips website and check if an updated SmartControl Lite driver is available When I click on Product Information only partial information is shown what happened It might be you
19. levels to accomodate today s wide range of computer applications Choose the setting that is most comfortable or efficient when viewing your application Alternatively simply choose the one that best describes its type ea Game o AE Internet Standard Options gt Preferences Will only be active when selecting Preferences from the drop down Options menu On a non supported W SmartControl 2 SmartControl Lite PHILIPS Preferences You can use the following options to configure SmartControl I Enable menu when right clicking on desktop Pr IV Enable task tray menu P ices IV Run at system start up Set Transparency 0 C 50 C 100 Adjust Audio Select language English x Auto Pivot Input Wizard Presets Multi Monitors IT Help Displays current preference settings A checked box enables the feature he check box is a toggle Enable Context Menu on desktop is checked On by default Enable Context menu displays SmartControl Lite selections for Select Preset and Tune Display in the desktop right click context menu Disabled removes SmartControl Lite from the right click context menu Enable Task Tray icon is checked On by default Enable context menu shows the task tray menu for SmartControl Lite A right click on the task tray icon displays the menu options for Help Technical Support Check for Upgrade About and Exit When Enable task tray menu is disabled the task tray icon will only
20. mettre des hyperfr quences qui si l appareil n est pas install et utilis selon les consignes donn es peuvent causer des interf rences nuisibles aux communications radio Cependant rien ne peut garantir l absence d interf rences dans le cadre d une installation particuli re Si cet appareil est la cause d interf rences nuisibles pour la r ception des signaux de radio ou de t l vision ce qui peut tre d cel en fermant l quipement puis en le remettant en fonction l utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes e R orienter ou d placer l antenne de r ception e Augmenter la distance entre l quipement et le r cepteur e Brancher l quipement sur un autre circuit que celui utilis par le r cepteur e Demander l aide du marchand ou d un technicien chevronn en radio t l vision Toutes modifications n ayant pas recu l approbation des services comp tents en mati re de conformit est susceptible d interdire l utilisateur l usage du pr sent quipement N utiliser que des cables RF arm s pour les connections avec des ordinateurs ou p riph riques CET APPAREIL NUMERIOUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA 27 EN 55022 Compliance Czech Republic Only This device belongs to category B devices as described in EN 55022 unless it is specifi cally stated that it is a Class A device o
21. monitor from mains power source immediately for safety e Contact with Philips customer service representative immediately El Imaging Problems Image is not centered e Adjust the image position using the Auto function in OSD Main Controls Adjust the image position using the Phase Clock of Setup in OSD Main Controls It is valid only in VGA mode Image vibrates on the screen Check that the signal cable is properly securely connected to the graphics board or PG Vertical flicker appears g LE LUI ULU e Adjust the image using the Auto function in OSD Main Controls e Eliminate the vertical bars using the Phase Clock of Setup in OSD Main Controls It is valid only in VGA mode Horizontal flicker appears e Adjust the image using the Auto function in OSD Main Controls e Eliminate the vertical bars using the Phase Clock of Setup in OSD Main Controls It is valid only in VGA mode Image appears blurred indistinct or too dark Adjust the contrast and brightness on On Screen Display An after image burn in or ghost image remains after the power has been turned off e Uninterrupted display of still or static images over an extended period may cause burn in also known as after imaging or ghost imaging on your screen Burn in after imaging or ghost imaging is a well known phenomenon in LCD panel technology In most cases the burned in or after imagi
22. or the store at which you purchased the product Your new monitor contains materials that can be recycled and reused Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of All redundant packing material has been omitted We have done our utmost to make the packaging easily separable into mono materials Please find out about the local regulations on how to dispose of your old monitor and packing from your sales representative Recycling Information for Customers Your display is manufactured with high quality materials and components which can be recycled and reused To learn more about our recycling program please visit www philips com about sustainability recycling 3 Sane un e montor Install b d 2 Setting up the monitor bic i 1 Place the monitor face down on soft and smooth surface taking care to avoid 2 1 Installation scratching or damaging the screen M Package contents 2 Hold the base stand with both hands and firmly insert the base stand into the base column 1 Gently attach the base to the base column until the latch locks the base 2 Use your fingers to tighten the screw located at the bottom of the base and secure the base to the column tightly VGA Audio cable 247E3LH EJ Connecting to your PC Model 247E3LPH Model 247E3L PHILIPS PHILIPS ODE RE PE 9
23. p yn w na system komputerowy Nie nale y wpycha zadnych przedmiot w do atwordw systemu komputerowego gdy mo e ta spowodowa po ar lub pora enie pr dem poprzez zwarcie element w wewn trznych System komputerowy powimen znajdowa si z dala od grzejnik w r de ciepla Ponadto mie nale y blokowa atwordw wentylacyjnych Nale y unika k adzenia luznych papeer w pod komputer oraz umieszczania komputera w ciasnym miejscu bez ma liwo ci cyrkulacji powi etrza wok niego North Europe Nordic Countries Information Placering Ventilation VARNING FORSAKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG AR LATATKOMLIGA N R DU STALLER DIN UTRUSTNING PAPLATS Placering Ventilation ADVARSEL S RG VED PLACERINGEN FOR AT NETLEDNINGENS STIK OG STIKKONTAKT EIS NEMT TIEGZEINGELIGE Paikka llmankierto VAROITUS SIJOITA LAITE SITEN ETT VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROT TAA PISTORASIASTA Plassering Ventilasjon ADVARSEL NAR DETTE UTSTYRET PLASSERES MA DU PASSE P AT KONTAKTENE FOR ST MTILFORSEL ER LETTE A NA BSMI Notice Taiwan Only WAzHENEm BE Ergonomie Hinweis nur Deutschland Der von uns gelieferte Farbmonitor entspricht den in der Verordnung ber den Schutz vor Sch den durch R ntgenstrahlen festgelegten Vorschriften Auf der R ckwand des Ger tes befindet sich ein Aufkleber der auf die Unbedenklichkert der Inbetriebnahme hinweist da die Vorschriften
24. types BLACK DOT DEFECTS ACCEPTABLE LEVEL 3 adjacent dark subpes 0 TOTAL DOT DEFECTS ACCEPTABLE LEVEL Total bright or black dot defects of all types G Note 1 1 or 2 adjacent sub pixel defects 1 dot defect 2 his monitor is ISO9241 307 compliant ISO9241 307 Ergonomic requirement analysis and compliance test methods for electronic visual displays 31 8 2 Customer Care amp Warranty For warranty coverage information and additional support requirement valid for your region please visit www philips com support website for details You may also contact your local Philips Customer Care Center number listed below Contact Information for WESTERN EUROPE region Country ASC Consumer care number Price gt 2 Contact Information for CENTRAL AND EASTERN EUROPE region Country Call center ASC Consumer care number Belarus Eo a ServiceNet LV Ltd Blue Ridge Intl 40 21 2101969 Serbia amp Montenegro NA Bulgaria INA Croatia INA Estonia INA Latvia i Lithuania NA Romania Slovenia PC Hand 386 1 530 08 24 Ukraine INA Topaz Service Company po o bana Ne o na Jes CS ussia INA CEEE Partners 7 495 645 3010 for sales Hungary Contact Information for LATIN AMERICA region Country Call center Consumer care number 0800 7254101 Vermont 0800 3330 856 Contact Information for China China Consumer care number 4008 800 008 NA NA NA NA NA NA NA NA NA NA NA NA
25. 20 80 RH e IMPORTANT Always activate a moving screen saver program when you leave your monitor unattended Always activate a periodic screen refresh application if your monitor will display unchanging static content Uninterrupted display of still or static images over an extended period may cause burn in also known as after imaging or ghost imaging on your screen Burn in after imaging or ghost imag ing is a well known phenomenon in LCD panel technology In most cases the burned in or after imaging or ghost imaging will disappear gradually over a period of time after the power has been switched off N Warning Severe burn in or after image or ghost image symptoms will not disappear and cannot be repaired he damage mentioned above is not covered under your warranty Service he casing cover should be opened only by qualified service personnel e fthere is any need for any document for repair or integration please contact with your local service center please refer to the chapter of Consumer Information Center e For transportation information please refer to Technical Specifications e Do not leave your monitor In a car trunk under direct sun light G Note Consult a service technician if the monitor does not operate normally or you are not sure what procedure to take when the operating instructions given in this manual have been followed 1 2 Notational Descriptions
26. 247E3L www philips com welcome EN User manual 1 Customer care and warranty 30 Troubleshooting amp FAQs 35 PHILIPS Table of Contents 1 Pur 1 1 1 Safety precautions and maintenance 1 2 Notational Descriptions 2 1 3 Disposal of product and packing M Naked O a nique 3 2 Setting up the monitor 4 AN ANECIA Ona ink Lm 4 2 2 Operating the monitor 6 2 3 Remove Base Stand 2 3 Image Optimization 10 3 1 Smar dma e ler 10 gt C O A i a uwaa u 3 3 Philips SmartControl Lite 11 4 PowerSensor M ssesesesesenesenenenenenenene 17 5 Technical Specifications 19 5 1 Resolution amp Preset Modes 22 6 Power Management 23 7 Regulatory Information 24 8 Customer care and warranty 30 8 1 Philips Flat Panel Monitors Pixel Basen go lo weer ee ees 30 8 2 Customer Care amp Warranty 32 9 Troubleshooting amp FAQs 35 24 IROUBIENOCINE une 29 9 2 SmartControl Lite FAQs 36 93 General FAQS Latet recto 37 1 Important This electronic users guide is intended for anyone who uses the Philips monitor lake time to read this user manual before you use your monitor It contains important information and notes regarding operating your monitor The Philips guarantee applies provided the product is handled properly f
27. 99992 buy out 34 9 Troubleshooting amp FAQs 9 1 Troubleshooting This page deals with problems that can be corrected by a user If the problem still persists after you have tried these solutions contact Philips customer service representative EB Common Problems No Picture Power LED not lit e Make sure the power cord is plugged into the power outlet and into the back of the monitor e First ensure that the power button on the front of the monitor is in the OFF position then press it to the ON position No Picture Power LED is White e Make sure the computer is turned on e Make sure the signal cable is properly connected to your computer e Make sure the monitor cable has no bent pins on the connect side If yes repair or replace the cable e The Energy Saving feature may be activated Screen says Attention Check cable connection e Make sure the monitor cable is properly connected to your computer Also refer to the Quick Start Guide e Check to see if the monitor cable has bent pins e Make sure the computer is turned on AUTO button doesn t function e The auto function is applicable only in VGA Analog mode If the result is not 35 satisfactory you can do manual adjustments via the OSD menu Note The Auto Function is not applicable in DVI Digital mode as it is not necessary Visible signs of smoke or sparks e Do not perform any troubleshooting steps e Disconnect the
28. CO CERTIFIED Requirement for Environment Labeling of Ergonomics Energy Ecology and Emission T CO Swedish Confederation of Professional Employees for TCO versions Energy Star Declaration www energystar gov As an ENERGY STAR Partner we have determined that this product meets the ENERGY STAR guidelines for energy efficiency ENERGY STAR G Note We recommend you switch off the monitor when it is not in use for a long time Federal Communications Commission FCC Notice U S Only G This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on
29. SmartControl Gu SmartControl Lite PHILIPS White Point White Point is the point at which equal combinations of red green and blue light at full intensity create white This effects the overall color quality For the most accurate colors click the Reset button then select the White Point 1 select the White Point value for the best possible color quality Black Level e i White Point 6500K _ u Undo Reset Options Calibration ap SmartImage Display Gamma 13 SmartControl Lite W SmartControl 2x PHILIPS Display Gamma Gamma is a component of the pixel brightness in a display A lower Gamma value produces brighter pixels and a higher Gamma value produces darker pixels The default value for Gamma is 2 2 To adjust Gamma Smartlmage must be set to Off Click the SmartImage Off button before adjusting M Gamma m Adjust RGB 1 Use the slider to select the desired Gamma e Black Level Color White Point Display Gamma 2 2 d E M Smartipage in wy Undo Reset Options Calibration ap M e SmartImage Help W SmartControl zx Calibration Your display needs to be properly calibrated in order for it to produce the widest range of colors accurately Calibration should always take place as the last tuning step in the process Remember to recalibrate any time you make individual adjustments to image quality or whenever you move your display to a new location l 1 Make all
30. acji Urz dzenie powinno by zasilane z gniazda z przy czonym obwodem ochronnym gniazdo z ko kiem Wsp pracuj ce ze sob urz dzenia Komputer monitor drukarka powinny by zas lane 2 tego szm go r d a Instalacja elektryczna pomieszczenia powinna zawiera w przewodzie fazowym rezerwowa ochran przed ywarciami w postaci bezpeecznika o warto ci znamionowej me wi kszej ni 16A amper w W celu ca kowitego wy czenia urz dzenia z sieci zasilania nale y wyj wtyczk kabla zasilaj cego z gmiazdka kt re powinno znajdowa sz w pobli u urz dzenia 1 by atwo dost pne Znak bezpiecze stwa B potwierdza zgodno urz dzenia z wymaganiami bezpiecze stwa u ytkowania zawartymi w PN 93 T 42107 1 PN R9 E 416251 Pozosta e instrukcje bezpiecze stwa Nie nale y u ywa wtyczek adapierowych lub usuwa ko ka obwodu ochronnego z wtyczki Je eli konseczne jest u ycie pezedluzacza to nale y u y przed u acza 3 ylowego z prawid owa po czonym przewodem ochronnym System komputerowy nale y zabezpieczy przed nag ymi chwilowymi wzrostami lub spad kami napsgcia u ywaj c eliminatora przepi urz dzenia dopasawuj cego lub bezzak ceniowega r d a zasilania Nale y upewni si aby nec me le a o na kablach systemu komputerowego oraz aby Kable me byty umieszczone w miejscu gdzie mo na by oby na nie nadeptywa lub poryka si o mie Nie nale y rozlewad napoj w ani zanych
31. ber die Bauart von St rstrahlern nach Anlage Il 5 Abs 4 der R ntgenverordnung erf llt sind Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht ist darauf zu achten dal 1 Reparaturen nur durch Fachpersonal durchgef hrt werden nur original Ersatzteile verwendet werden bei Ersatz der Bildr hre nur eine bauartgleiche eingebaut wird Aus ergonomischen Gr nden wird empfohlen die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden schlechte Lesbarkeit und erh hte Augenbelastung bei zu geringem Zeichenkontrast waren die Folge Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betr gt OdB A oder weniger D ACHTUNG BEIM AUFSTELLEN DIESES GERATES DARAUF ACHTEN DAB NETZSTECKER UND NETZKABELANSCHLUR LEICHT ZUGANGLICH SIND China RoHS The People s Republic of China released a regulation called Management Methods for Controlling Pollution by Electronic Information Products or commonly referred to as China RoHS All products including CRT and Monitor which are produced and sold for China market have to meet China RoHS request PER B RoHS RAE REAA CRAB MORRIE th eR PEJKEEROHS DAERAH T ZA PAIREE A ETA EB SDAA RAR SB EREA M ERA RECHT ESAERA BMA BR tuu d msi a X A Ores SRE RZ Pb Hg Cd Cr6 PBB PBDE AR o jo o o o O CRT mE x O O O O O WURBIA TE x o O O O ERZE TE x O O O O O PRERA x O
32. ct Reset to recall all of the original factory settings Is the LCD screen resistant to scratches In general it is recommended that the panel surface is not subjected to excessive shocks and is protected from sharp or blunt objects When handling the monitor make sure that there is no pressure or force applied to the panel surface side This may affect your warranty conditions How should clean the LCD surface For normal cleaning use a clean soft cloth For extensive cleaning please use Isopropyl alcohol Do not use other solvents such as ethyl alcohol ethanol acetone hexane etc Can I change the color setting of my monitor Yes you can change your color setting through OSD control as the following procedures Press OK to show the OSD On Screen Display menu Press Down Arrow to select the option Color then press OK to enter color setting there are three settings as below 1 Color Temperature With settings in the 6500K range the panel appears warm with a red white color tone while a 9300K temperature yields cool blue white toning 38 sRGB this is a standard setting for ensuring correct exchange of colors between different device e g digital cameras monitors printers scanners etc User Define the user can choose his her preference color setting by adjusting red green blue color amp Note A measurement of the color of light radiated by an object while it is being heate
33. d his measurement is expressed in terms of absolute scale degrees Kelvin Lower Kevin temperatures such as 2004K are red higher temperatures such as 9300K are blue Neutral temperature is white at 6504K Q9 Ans Q10 Can connect my LCD monitor to any PC workstation or Mac Yes All Philips LCD monitors are fully compatible with standard PCs Macs and workstations You may need a cable adapter to connect the monitor to your Mac system Please contact your Philips sales representative for more information Are Philips LCD monitors Plug and Play Yes the monitors are Plug and Play compatible with Windows Vista XP NT Mac OSX Linux What is Image Sticking or Image Burn in or After Image or Ghost Image in LCD panels Uninterrupted display of still or static images over an extended period may cause burn in also known as after Imaging or ghost imaging on your screen Burn in after imaging or ghost imaging is a well known phenomenon in LCD panel technology In most cases the burned in or atter imaging or ghost imaging will disappear gradually over a period of time after the power has been switched off Always activate a moving screen saver program when you leave your monitor unattended Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content N Warning Severe burn in or after image or ghost image symp
34. e sidebar to 1920x1080 pixels Open Advanced Properties and set the Refresh Rate to 60Hz then click OK Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1920x1080 60Hz Shut down your computer disconnect your old monitor and reconnect your Philips LCD monitor Turn on your monitor and then turn on your PC What is the recommended refresh rate for LCD monitor Recommended refresh rate in LCD monitors is 60Hz In case of any disturbance on screen you can set it up to 5Hz to see if that removes the disturbance What are the inf and icm files on the CD ROM How do I install the drivers inf and icm These are the driver files for your monitor Follow the instructions In your user manual to install the drivers Your computer may ask you for monitor drivers inf and icm files or a driver disk when you first install your monitor Follow the instructions to insert the companion CD ROM included in this package Q4 Ans Q5 Ans Q6 Ans Q7 Ans Q8 Ans Monitor drivers inf and icm files will be installed automatically How do I adjust the resolution Your video card graphic driver and monitor together determine the available resolutions You can select the desired resolution under Windows9 Control Panel with the Display properties What if get lost when am making monitor adjustments via OSD Simply press the OK button then sele
35. ements in the world his makes for a high performance product designed with the user in focus that also minimizes the impact on the climate and our natural environment TCO Certified is a third party verified program where every product model is tested by an accredited impartial test laboratory I CO Certified represents one of the toughest certifications for displays worldwide Some of the Usability features of the TCO Certified for displays e Visual ergonomics for good image quality Is tested to ensure top performance and reduce sight and strain problems Important parameters are luminance contrast resolution black level gamma curve colour and luminance uniformity and colour rendering e Products are tested according to rigorous safety standards at impartial laboratories 24 e Electric and magnetic fields emissions as low as normal household background levels low acoustic noise emissions when applicable Some of the Environmental features of the TCO Certified for displays e he brand owner demonstrates corporate social responsibility and has a certified environmental management system EMAS or ISO 14001 Very low energy consumption both in on and standby mode minimize climate impact e Restrictions on chlorinated and brominated flame retardants plasticizers plastics and heavy metals such as cadmium mercury and lead ROHS compliance e Both product and product packaging is prepared for rec
36. erent types of pixel defects and defines acceptable defect levels for each type In order to qualify for repair or replacement under warranty the number of pixel defects on a TFT Monitor panel must exceed these acceptable levels For example no more than 0 000476 of the sub pixels on a monitor may be defective Furthermore Philips sets even higher quality standards for certain types or combinations of pixel defects that are more noticeable than others This policy is valid worldwide a A subpixel pixel U z Pixels and Sub pixels A pixel or picture element is composed of three sub pixels in the primary colors of red green and blue Many pixels together form an image When all sub pixels of a pixel are lit the three colored sub pixels together appear as a single white pixel When all are dark the three colored sub pixels together appear as a single 30 black pixel Other combinations of lit and dark sub pixels appear as single pixels of other colors Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways There are two categories of pixel defects and several types of sub pixel defects within each category Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or on That is a bright dot is a sub pixel that stands out on the screen when the monitor displays a dark pattern here are the types of bright dot defects di h
37. ght gaming and video images or displays clear readable text for office work By reducing your monitor s power consumption you save on energy costs and extend the lifetime of your monitor EJ How does it work When you activate SmartContrast it will analyse the content you are displaying in real time to adjust colors and control backlight intensity T his function will dynamically enhance contrast for a great entertainment experience when viewing videos or playing games 3 3 Philips SmartControl Lite The new SmartControl Lite software by Phillips allows you to control your monitor via an easy to use on screen graphic interface Complicated adjustments are a thing of the past as this user friendly software guides you through fine tuning resolution Color calibration Clock Phase adjustments RGB White point adjustment etc Equipped with latest technology in core algorithm for fast processing and response this Windows compliant eye catching animated Icon based software is ready to enhance your experience with Philips monitors 11 EJ Installation e Follow the instruction and complete the installation e You can launch after installation is completed e f you want to launch later you can either click the shortcut on desktop or toolbar PHILIPS www philips com welcome Monitor driver and software installation Required steps gt Select Language System requirements PC running Windows 7 Vista XP 2000 98
38. hoose and press OK button to confirm selection and close the Smartlmage Lite OSD There are three modes to be selected Standard Internet Game SmartImage Standard Internet Game Standard Enhances text and dampens brightness to increase readability and reduce eye strain This mode significantly enhances readability and productivity when you re working with spreadsheets PDF files scanned articles or other general office applications e Internet his profile combines color saturation dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors all without artifacts and faded colors e Game lurn on over drive circuit for best response time reduce jaggy edges for fast moving objects on screen enhance contrast ratio for bright and dark scheme this profile delivers the best gaming experience for gamers 3 2 SmartContrast EB What is it Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor s contrast ratio for maximum visual clarity and viewing enjoyment stepping up backlighting for clearer crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds E31 Why do I need it You want the very best visual clarity and viewing comfort for every type of content SmartContrast dynamically controls contrast and adjusts backlighting for clear crisp bri
39. l Support displays the tech support page e Check for Update takes the user to PDI Landing and checks the user s version against the most current available e About Displays detailed reference information product version release information and product name Exit Close SmartControl Lite To run SmartControl Lite again either select SmartControl Lite from Program menu double click the desktop PC icon or restart the system PHILIPS SmartControl SmartControl Version 3 d une standard R2007 01 04 1151 23 Copyright 1993 2007 Portrait Displays Inc Patents Pending Task Tray Menu Disabled When the Task Tray is disabled in the preference folder only the EXIT selection is available To completely remove SmartControl Lite from the task tray disable Run at Startup in Options Preferences 4 PowerSensor M Available for model 247E3LPH only PowerSensor is a unique environmentally friendly technology from Philips which enables user to save up to 80 of power consumption In line with Philips Sense and Simplicity Promise this user friendly technology works for you right out of the box without any hardware or software installation and without any user intervention in the default mode EB How does it work e PowerSensor works on principle of transmission and reception of harmless infrared signals in order to detect user presence e When the user is in front of the monitor the monitor operates
40. lution 1920x1080 or software installed In your Po ine monitor Contes can automatically reduce its power consumption l l when not in use If an input from a keyboard Brightness 300 nits mouse or other input device is detected e Color temperature 6500k with full white the monitor will wake up automatically The pattern on me ei consumption Note ME NEC This data is subject to change without notice feature 247E3L VESA Switch OF OFF 05W typ OFF 247E3LH VESA M W 7 amp 20 85 W typ ctive es es 26W max White Switch OF OFF 03W wp OFF 247E3LPH E e Switch OF OFF 03W yp OFF 20 85 W typ 23 7 Regulatory Information Lead free Product Lead free display promotes environmentally sound recovery and disposal of waste from electrical and electronic equipment Toxic substances like Lead has been eliminated and compliance with European community s stringent RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment have been adhered to in order to make Philips monitors safe to use throughout its life cycle Congratulations This display is designed for both you and the planet The display you have just purchased carries the TCO Certified label This ensures that your display is designed manufactured and tested according to some of the strictest quality and environmental requir
41. n a loss of detail in darker image areas Adjust the Brightness for the best possible picture quality 1 Lower the Brightness to the minimum level 2 Raise the Brightness to the desired level 3 Adjust the Brightness as needed to achieve an equal separation of the stripes Brightness 100 Undo Reset PHILIPS Contrast Adjust the Contrast use the slider to keep details in lighter image areas 1 Raise the Contrast until the numbers 1 and 2 are no longer visible 2 Slowly lower the Contrast to make the numbers 2 and 3 reappear The number 1 should remain barely visible Contrast u Undo Reset W SmartControl SmartControl Lite 2 Brightness o Contrast Focus a amp Position Options LA Resolution Help W SmartControl SmartControl Lite Brightness E ad e o a a a Color Y m o a c G Options vie Resolution Help WS SmartControl SmartControl Lite Adjust Q Color Brightness Focus Options SE Resolutio Help PHILIPS Focus Your display s timing needs to be synchronized with the video signal 1 Choose Auto Setup 2 Ifthe vertical bands are still visible you ll need to adjust the Pitch Pitch Try to make the vertical bands disappear Phase Adjust to the brightest setting to minimize movement on the screen Pitch 50 z t Phase 17 t Undo Auto Setup
42. n the specification label The following applies to devices in Class A of EN 55022 radius of protection up to 30 meters The user of the device is obliged to take all steps necessary to remove sources of interference to tele communication or other devices Pokud neni na typov m titku po ita e uvedeno e spad do do tidy A podle EN 55022 spad automaticky do tfidy B podle EN 55022 Pro zafizeni za azen do tidy A chrann p smo 30m podle EN 55022 plat n sleduj c Dojde li k ru en telekornunikatnich nebo Bnych zafizeni je u ivatel povinnen prov st takov opatfgni aby ru en odstranil Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit a three prong socket All equipment that works together computer monitor printer and so on should have the same power supply source The phasing conductor of the room s electrical installation should have a reserve short circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes A lo completely switch off the equipment the power supply cable must be removed from the power supply socket which should be located near the equipment and easily accessible A protection mark B confirms that the equipment is in compliance with the protection usage requirements of standards PN 93 1 42107 and PN 89 E 06251 Wymagania Polskiego Centrum Bada i Certyfik
43. ng or ghost imaging will disappear gradually over a period of time after the power has been switched off e Always activate a moving screen saver program when you leave your monitor unattended e Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content Severe burn in or after image or ghost image symptoms will not disappear and cannot be repaired The damage mentioned above is not covered under your warranty Image appears distorted Text is fuzzy or blurred Set the PC s display resolution to the same mode as monitors recommended screen native resolution Green red blue dark and white dots appears on the screen he remaining dots are normal characteristic of the liquid crystal used in today s technology Please refer the pixel policy for more detail The power on light is too strong and is disturbing e You can adjust power on light using the power LED Setup in OSD main Controls 36 For further assistance refer to the Consumer Information Centers list and contact Philips customer service representative 9 2 SmartControl Lite FAQs Q1 change the monitor on a PC to a different one and the SmartControl Lite becomes un usable what do do Restart your PC and see if SmartControl Lite can work Otherwise you will need to remove and re install SmartControl Lite to ensure proper driver is installed The SmartControl Lite
44. normally at the predetermined settings that the user has set i e Brightness contrast color etc e Assuming that the monitor was set to 100 of brightness for example when the user leaves his seat and is no longer in front of the monitor the monitor automatically reduces the power consumption down to 8076 User present in front User not present Power consumption as illustrated above is for reference purpose only FJ Setting Default settings At its default setting Setting 3 PowerSensor is designed to detect the presence of the user located between 90 and 110 cm 35 4 and 43 3 inches from the display and within five degrees left or right of the monitor Custom settings e f you prefer to be in a position outside the perimeters listed above choose a higher strength signal for optimal detection efficiency The higher the setting the stronger the detection signal For maximum PowerSensor efficiency and proper detection please position yourself directly in front of your monitor e f you choose to position yourself more than 110 cm or 43 3 inches from the monitor use the maximum detection signal for distances up to 130 cm or 51 2 inches Setting 4 Since some dark colored clothing tends to absorb infrared signals even when the user is within 100 cm or 40 inches of the display step up signal strength when wearing black or other dark clothes 17 e You can return to the default mode at any time Setting 3
45. on pane and current input source setting On single input displays this pane will not be visible Options gt Audio Will only be active when selecting Audio from the drop down Options Menu On a non supported display capable of DDC Cl only the Help and Options tabs are available W SmartControl SmartControl Lite Adjust Color Options 9 Auto Pivot B Input b Wizard Presets ga Multi Monitors X PHILIPS Audio Adjust the Volume of the integrated loudspeakers by using the slider Turn off the integrated loudspeakers by checking the Mute checkbox Mute Volume 100 t Undo 15 Help gt User Manual Will only be active when selecting User Manual from the drop down Help menu On a non supported display capable of DDC CI only the Help and Options tabs are available WS SmartControl SmartControl Lite Adjust bk U ual em Update Color a Display ID i System ID Options PE 4 gt Version Help PHILIPS User Manual If you need help setting up or operating SmartControl click the Tech Support button You ll have the option to fill out an Assistance Form You can also choose to have information about your software automatically attached to the assistance form You ll need to be online to use this feature User Manual Tech Support Help gt Version Will only be active when selecting Version from the drop down Help menu On
46. or high impact conditions during operation e Do not knock or drop the monitor during operation or transportation Maintenance To protect your monitor from possible damage do not put excessive pressure on the LCD panel When moving your moni tor grasp the frame to lift do not lift the monitor by placing your hand or fingers on the LCD panel e Unplug the monitor if you are not going to use it for an extensive period of time e Unplug the monitor if you need to clean it with a slightly damp cloth The screen may be wiped with a dry cloth when the power Is off However never use organic solvent such as alcohol or ammonia based liquids to clean your monitor e To avoid the risk of shock or permanent damage to the set do not expose the monitor to dust rain water or excessive moisture environment e fyour monitor gets wet wipe it with dry cloth as soon as possible e fforeign substance or water gets in your monitor please turn the power off immedi ately and disconnect the power cord Then remove the foreign substance or water and send it to the maintenance center Do not store or use the monitor in loca tions exposed to heat direct sunlight or extreme cold e In order to maintain the best performance of your monitor and use it for a longer life time please use the monitor in a location that falls within the following temperature and humidity ranges e Temperature 0 40 C 32 95 F e Humidity
47. or its intended use in accordance with its operating instructions and upon presentation of the original invoice or cash receipt indicating the date of purchase dealers name and model and production number of the product 1 1 Safety precautions and mainte nance N Warnings Use of controls adjustments or procedures other than those specified in this documentation may result in exposure to shock electrical hazards and or mechanical hazards Read and follow these instructions when connecting and using your computer monitor Operation e Please Keep the monitor out of direct sunlight very strong bright lights and away from any other heat source Lengthy exposure to this type of environment may result in discoloration and damage to the monitor Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor s electronics e Do not block the ventilation holes on the cabinet When positioning the monitor make sure the power plug and outlet are easily ac cessible e If turning off the monitor by detaching the power cable or DC power cord wait for 6 seconds before attaching the power cable or DC power cord for normal operation e Please use approved power cord provided by Philips all the time If your power cord Is missing please contact with your local service center Please refer to Customer Care Consumer Information Center e Do not subject the monitor to severe vibration
48. other necessary adjustments to image M quality first Adjust RGB 2 Press Show Me to learn how to use the calibration tools il 3 Finally press Start to begin the calibration process Black Level IV Enable color calibration Color software designed in collaboration with Joseph Holmes Color White Point Protected by U S Patent No 6 686 953 Ok 1 GG Display Gamma Options Calibration ap sa SmartImage Help Show Me Start Quick View Show Me starts color calibration tutorial Start starts the 6 step color calibration sequence Quick View loads the before after images To return to Color home pane click the Cancel button Enable color calibration by default is on If unchecked does not allow for color calibration to happen dimes out start and quick view buttons Must have patent info in calibration screen e Previous button is disabled until the second color screen e Next goes to the succeeding target 6 targets e Final next goes File gt Presets pane e Cancel closes the Ul and returns to the plug in page Smartlmage Lite Allows user to change setting for better display setting based on content When Entertainment is set SmartContrast and SmartResponse are enabled W SmartControl SmartControl Lite RGB Black Level White Point Display Gamma I Options Calibration PHILIPS Smartimage SmartImage provides different brightness and contrast
49. r graphic card adaptor driver is not the most updated version which fully supporting DDC CI interface Please try to download the most updated graphic adaptor driver from corresponding companies web site Install the driver Remove SmartControl Lite and re install it once more Attention Theft mode enabled forgot my PIN for Theft Deterrence Function What can I do Philips Service center has a right to ask for legitimate identification and authorization in order to establish ownership of the monitor Please note that the anti theft deterrence function is provided as a convenient free option Managing PIN numbers is the sole responsibility of the individual user or the organization who sets it In case the PIN number is forgotten Philips service center can re set it for you at a nominal charge after verification of ownership Please note that this activity is not covered by standard warranty terms 37 9 3 Q1 Q2 Ans Q3 General FAQs When install my monitor what should do if the screen shows Cannot display this video mode Recommended resolution for this monitor 1920x1080 60Hz Unplug all cables then connect your PC to the monitor that you used previously In the Windows Start Menu select Settings Control Panel In the Control Panel Window select the Display icon Inside the Display Control Panel select the Settings tab Under the setting tab in box labelled desktop area move th
50. t Signal User Convenience Separate Sync Sync on Green 247E3L Ep v amp A amp 3 4 amp OK b 247E3L 1A ED Y A lt E K b 247E3LH X ED Y A 1 lt amp 0K b 247E3LPH amp v A SENSOR lt 4 amp OK b OSD Languages English French German Spanish Italian Russian Simplified Chinese Portuguese Turkish Other Convenience Kensington Lock Plug amp Play Compatibility Tilt DDC CI sRGB Windows 7 Vista KP Mac OSX Linux 2 20 247E3L On Mode typ 20 85W typ Energy Consumption EnergyStar 5 0 test method AC Input Voltage at AC Input Voltage at AC Input Voltage at 100VAC 5VAC 115VAC 5VAC 230VAC 5VAC 50Hz 3Hz 60Hz 3Hz 50Hz 3Hz Normal Operation typ 16 86W 1E 73W 16 6W 19 Sleep typ 0 5W 0 5W 0 5W Off typ 0 5W 0 5W 0 5W AC Input Voltage at AC Input Voltage at AC Input Voltage at Heat Dissipation 100VAC 5VAC 115VAC 5VAC 230VAC 5VAC 50Hz 3Hz 60Hz 3Hz 50Hz 3Hz Normal Operation 5754 IRI SI eA ate 56 66 BTU hr Sleep WZRETEM A eTO TETON Off W ate ein klein ZEN Power LED indicator On mode White Standby Sleep mode White blinking Power Supply Built in 100 240VAC 50 60Hz 247E3LH Power On Mode typ 20 85W typ 26VV max CME AC Input Voltage at AC Input Voltage at AC
51. tent dynamically adjusting brightness contrast color and sharpness in real time Whether you re working with text applications displaying images or watching a video Philips Smartlmage Lite delivers great optimized monitor performance P Why do I need it You want a monitor that delivers optimized display all your favorite types of content Smartlmage Lite software dynamically adjust brightness contrast color and sharpness in real time to enhance your monitor viewing experience EJ How does it work Smartlmage Lite is an exclusive leading edge Philips technology that analyzes the content displayed on your screen Based on a scenario you select Smartlmage Lite dynamically enhances the contrast color saturation and sharpness of images to enhance the contents being displayed all in real time with the press of a single button Z How to enable Smartlmage Lite 1 Press ED to launch the Smartlmage Lite on screen display 2 Keep pressing EP to toggle between Standard Internet Game 10 3 The Smartlmage Lite on screen display will remain on screen for 5 seconds or you can also press OK button to make confirmation 4 When Smartlmage Lite is enabled the sRGB scheme is disabled automatically To use sRGB you need to disable Smartlmage Lite with the ED button at the front bezel of your monitor Except using ED key to scroll down you can also press w A buttons to c
52. toms will not disappear and cannot be repaired The damage mentioned above is not covered under your warranty Q12 Why is my Display not showing sharp text and is displaying jagged characters Ans Your LCD monitor works best at its native resolution of 1920x1080 260Hz For best display please use this resolution 29 PHILIPS 2011 O Koninklijke Philips Electronics N V All rights reserved Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips Electronics N V and are used under license from Koninklijke Philips Electronics N V Specifications are subject to change without notice Version M3247E1T
53. ycling e The brand owner offers take back options The requirements can be downloaded from our web site he requirements included in this label have been developed by TCO Development in co operation with scientists experts users as well as manufacturers all over the world Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user friendly direction Our labeling system started with displays in 1992 and is now requested by users and l T manufacturers all over the world About 5076 of all displays worldwide are T CO certified For more information please visit www tcodevelopment com TCOF1058 TCO Document Ver 2 1 Ir Technology for you and the planet CERTIFIED EPEAT www epeat net The EPEAT Electronic e Product Environmental Assessment lool program evaluates computer desktops laptops and monitors based on 51 environmental criteria developed through an extensive stakeholder consensus process supported by US EPA cR EPEAT system helps purchasers in the public and private sectors evaluate compare and select desktop computers notebooks and monitors based on their environmental attributes EPEAT also provides a clear and consistent set of performance criteria for the design of products and provides an opportunity for manufacturers to secure market recognition for efforts to reduce the environmental impact of its products Benefits of EPEAT

Philips 247E3LSU

Contents

Download Pdf Manuals

Related Search

Related Contents