Raw International VSA1 flat panel wall mount
Contents
1. Before beginning the installation of your new LCD mount first verify that you have all of the necessary tools at hand The following tools are required for proper installation e Phillios screwdriver e Stud finder for drywall installation e Electric drill and 5 16 8mm masonry bit for concrete brick installation Also make sure that all of the hardware has been included with your mount You should find the following x4 2 5 Drywall Screw A x4 Concrete Anchor B x4 M4x12mm Bolt C x4 M4x380mm Bolt D x1 Security Bolt F x4 3 4 Spacer E x1 Allen Wrench G Step 1 Mounting the Wall Piece Drywall Installation IMPORTANT The weight of the LCD requires installation into a wood stud Failure to do so may result in damage or injury Use a stud finder to locate a wood stud where you want to install your mount It is recommended that you verify the location of the stud using a small nailor an awl You should use the center of the stud After the stud has been located place the wall piece against the wall with the hook towards the bottom Secure the wall piece using one Drywall Screw A but do not completely tighten the screw Using the integrated bubble guide carefully adjust the wall piece until it is level Insert the remaining screws into the wall piece and tighten Concrete Brick Installation Begin by placing the wall piece into position against the wall with the hook towards the bottom Using the integrated2. Step 3 Final Installation and Operation Final installation To complete the installation simply slide the arm piece with your LCD attached into the wall piece The plastic tab on the top of the wall piece should click indicating that the arm piece is secure If you need to remove the arm piece push in on the tab and slide the arm up For additional security and stability insert the security bolt F into the hole located on base of the arm piece and tighten using the Allen Wrench G included in the hardware kit Operation and Adjustment NOTE Adjustment of your LCD may vary by model On most models the tilt angle of your LCD can be adjusted by first loosening the gear joint that holds the tilt in place To do this locate the adjustment knob directly behind the LCD mounting point Loosen it by turning the Knob counter clockwise Adjust the tilt to the desired level and re tighten the knob see illustration 20 20 Other viewing adjustments can be made by simple moving the arm into the desired position If you find that a joint is too difficult to move or does not hold the LCD in place you can adjust the tightness of the joint If your mount includes black adjustment knobs turn a knob clockwise to tighten and counter clockwise to loosen If your mount does not have knobs use the Allen Wrench G to tighten or loosen the joint
3. bubble guide to keep it level mark off the holes that will be used for securing the mount and place the wall piece aside Next drill holes using an electric drill and 5 16 8mm masonry bit Remove any excess dust from the holes and inserta Concrete Anchor B into each hole If necessary use a hammer to lightly tap each anchor into place so that they are flush with the wall Once all of the anchors are in place put the wall piece back into position Attach the wall piece using the Drywall Screws A provided Make sure all Screws are snug but be careful not to over tighten them PCCP OSES ESSE EEO SLOT E EES EOEEOEEEOEHEH OE EHEHOHEREEEEE EE EEOEEHETSOEEE TOSSES HE EOETHEHOEEOEHHEE EH EEO ETHEL EEE TEE HOEEOETEOHOEHOEHHEEOEE EEOC EHE HOE H EE EEEEEEE HOLES EEEEDEOEEEE HELE SEH ESE EETO OES Step 2 Attaching the Arm to the LCD IMPORTANT Make sure the LCD is unplugged before starting this step of the installation and never lay the LCD face down as this may damage the viewing surface Before attaching the arm piece of the mount to your LCD you must first determine which hardware to use Do this by examining the back of the LCD If your LCD has a flat back use the M4x12mm Bolts C If your LCD has a recessed back use the longer M4x30mm Bolts D and 3 4 Spacers E After you have determined the appropriate bolts use them to attach the arm piece of the mount to the back of your LCD Be careful not to over tighten the bolts
Download Pdf Manuals
Related Search