Chief KSA1011B mounting kit
Contents
1. lt 20 lt 5 Figure 1 Parts Model KSA 1011 Installation Instructions ASSEMBLY ASSEMBLE Y CONNECTOR TO MOUNT Y Connector 10 may be installed to either a desk or wall mount mount not included See applicable assembly instructions that follow Desk Mount 1 If previously attached disconnect cables from display then remove display See instructions included with desk mount and or interface 2 If previously attached loosen do not remove clamp attach screw See Figure 2 Remove desk mount from desk See instructions included with desk mount lt a Mount Arm Attach Screw lt t Washer Stainless Steel Oo Washer Plastic Dea Nt Figure 2 Disassemble Desk Mount 3 Turn mount assembly upside down and place in your lap With one hand grasp desk mount housing and lift slightly off lap With other hand using 3 16 hex key loosen and remove mount arm attach screw and other related items See Figure 2 Retain all items except stop plate for later mount arm assembly NOTE Slightly lifting desk mount housing will keep nut in recessed cavity assisting screw removal NOTE After mount arm is removed nut can be retrieved by turning desk mount housing upside down 4 Remove stop screw and stop collar from mount arm See Figure 2 These will not be reused with Y connector 10 5 Using 2 5mm hex key remove and retain desk mo2. 7 Insert nut 80 into recessed cavity of wall mount housing as shown See Figure 8 Wall Mount Housing 80 in recessed cavity Figure 8 Install Nut 8 Install screw 50 through washer 70 washer 60 washer 70 and Y connector 10 into nut 80 See Figure 7 9 Using 3 16 hex key tighten screw 50 as required to maintain desired Y connector 10 position 10 Install wall mount housing to wall plate per instructions included with wall mount 11 Proceed to ASSEMBLE MOUNT ARMS TO Y CONNECTOR ASSEMBLE MOUNT ARMS TO Y CONNECTOR 1 Insert retained pin into Y connector 10 upper bore See Figure 9 Mount Arm Assembly a Screw Washer Stainless Steel DJ ANG se asher plastic SAT ali In a Washer Stainless Steel gt amp 40 or Plastic Spacer i NOTE All parts same for both sides lt Desk Mount Wall Mount similar Figure 9 Multi Dual Arm Assembly 2 Install washer 40 or retained plastic spacer as desired on pin See Figure 9 NOTE Washer 40 will lock arm to Y connector Spacer will allow limited movement of arm relative to Y connector 10 dependentupon tension of screw Insert mount arm assembly on pin See Figure 9 While holding retained nut in lower bore of Y connector 10 insert retained screw through retained washers stainless steel washer plastic was
3. removed See Figure 11 Retain nut Screw and washers may remain in outer mount arm assembly Screw amp Washers i im dp Outer mount arm assembly Inner mount arm assembly Spacer or gt 40 wile Figure 11 Multi Dual Arm Modification 3 Lift outer mount arm assembly from pin with screw and washers and place on protective surface 4 Remove spacer from pin See Figure 11 Install washer 40 on pin See Figure 11 6 Re install outer mount arm assembly with screw and washers on pin See Figure 11 7 Insert and hold nut in lower bore of inner mount arm assembly See Figure 11 8 Tighten screw as required using 3 16 hex key See Figure 11 9 Install display s to mount See instructions included with mount and or interface 10 Install cables to display 11 Modification is complete Model KSA 1011 Installation Instructions
4. INSTALLATION INSTRUCTIONS Y Connector Accessory For Multi Dual Arm Mounting Systems Model KSA 1011 Specifications Installs to K Series desk or wall mount Accommodates K Series mounting arms fixed and height adjustable Weight capacity of 40 Ibs 18 kg total for all equipment attached to KSA 1011 KSA 1011 Shown with optional desk mount and mounting arms wall mount similar BEFORE YOU BEGIN WARNING It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty If you have any questions about this these instructions or your specific installation contact Chief Manufacturing at 1 800 582 6480 or 952 894 6280 CHIEF MANUFACTURING INC 8807 000034 1 800 582 6480 952 894 6280 FAX 952 894 6918 2006 Chief Manufacturing NN 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com Ideas Supporting Ideas SAVAGE MINNESOTA 55378 USA 03 06 Model KSA 1011 Installation Instructions A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding inst
5. her and stainless steel washer mount arm assembly and Y connector 10 into retained nut See Figure 9 A CAUTION Improper positioning of desk mount arm may result in failure of mount and subsequent damage to displays Do NOT position either arm in gray shaded area 5 Position desk mount arm within UNSHADED area as shown See Figure 10 Tighten screw as required using 3 16 hex key NOTE This step not applicable to wall mount arms Installation Instructions Model KSA 1011 DO NOT POSITION EITHER ARM IN GRAY SHADED AREA ALLOWABLE NE ARM AREA Figure 10 Allowable Arm Area 6 Repeat Steps 1 through 5 for second mount arm assembly 10 7 Install displays to mount See instructions included with mount and or interface 8 Install cables to display 9 Assembly is complete If desired proceed to MODIFICATION OF MOUNT ARMS MODIFICATION OF MOUNT ARMS If desired each mount arm assembly may be modified to prevent movement of one arm relative to the other arm without loosening screw NOTE Spacer will allow limited movement of one arm relative to the other arm dependent upon tension of screw Washer 40 will lock arms together 1 If previously attached disconnect cables from display then remove display See instructions included with mount and or interface 2 Using 3 16 hex key loosen screw until nut can be
6. late and attach screws Ensure clamp faces center of desk mount as shown See Figure 3 14 Install mount to desk per instructions included with desk mount 15 Proceed to ASSEMBLE MOUNT ARMS TO Y CONNECTOR Wall Mount 1 If previously attached disconnect cables from display then remove display See instructions included with wall mount and or interface 2 If previously attached loosen do not remove set screw and remove wall mount housing from wall plate Do NOT remove wall plate from wall See instructions included with wall mount Remove mount arm from wall mount See Figure 6 Retain all hardware for later mount arm assembly 4 Mount Arm Attach Screw De Washer Stainless Steel SO Washer Plastic lt Washer Stainless Steel lt a Mount Arm _ Spacer Oa Nut Wall Mount Housing 4 Figure 6 Disassemble Wall Mount Install pin 20 into wall mount See Figure 7 amp D 40 or 30 x 20 lt a Wall Mount Housing Figure 7 Assemble Y Connector to Wall Mount Model KSA 1011 Installation Instructions 5 Install washer 40 or spacer 30 as desired on pin 20 See Figure 7 NOTE Washer 40 will lock Y connector 10 to wall mount Spacer 30 will allow limited movement of Y connector 10 relative to wall mount dependent upon tension of screw 50 6 Install Y connector 10 on pin 20 See Figure 7
7. ructions WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the KSA 1011 including both displays and interfaces does not exceed 40 Ibs 18 kg e The weight capacity of the KSA 1011 may be LIMITED to the lowest weight capacity of any other component located between the KSA 1011 and the supporting structure WARNING Allowing any part of your body or component cables to be caught between movable parts can result in serious personal injury or damage to equipment TOOLS REQUIRED FOR INSTALLATION e Pencil with eraser for desk mount e 3 16 Hex Key included with desk and wall mount e 2 5mm Hex Key included with desk mount NOTE Other tools may be required depending on your method of installation Installation Instructions Model KSA 1011 PARTS After unpacking carton inspect and verify contents See Figure 1 If any listed parts are missing or damaged contact Chief Customer Service at 1 800 582 6480 Table 1 Parts Item Description Qty 10 Y CONNECTOR 1 20 PIN Pivot 1 30 SPACER UHMW plastic 1 40 WASHER Lock External Tooth 5 8 5 50 SCREW Button Head Cap 5 16 18 x 3 3 4 1 60 WASHER 5 16 UHMW plastic 1 70 WASHER 5 16 Stainless Steel 2 80 NUT Lock Nylock 5 16 18 1 MOUNT Desk or Wall Required not included 1 2
8. unt base plate and attach screws See Figure 3 Desk Mount Housing Attach Screws gt 3 places m Figure 3 Desk Mount Base Plate 6 Turn desk mount housing right side up and install pin 20 into housing See Figure 4 Figure 4 Assemble Y Connector to Desk Mount Installation Instructions Model KSA 1011 7 Install washer 40 or spacer 30 as desired on pin 20 See Figure 4 NOTE Washer 40 will lock Y connector 10 to desk mount Spacer 30 will allow limited movement of Y connector 10 relative to desk mount dependent upon tension of screw 50 8 Install Y connector 10 on pin 20 See Figure 4 Install screw 50 through washer 70 washer 60 and washer 70 into Y connector 10 See Figure 4 10 While holding Y connector 10 desk mount housing and screw 50 together turn entire assembly upside down 11 Insert eraser end of pencil into plastic lock ring of nut 80 Using pencil thread nut 80 onto end of screw 50 several turns See Figure 5 If necessary rotate clamp to permit access Desk Mount Housing 50 80 in recessed cavity Figure 5 Install Nut 12 Using 3 16 hex key tighten screw 50 as required to maintain desired Y connector 10 position Ensure nut 80 fully seats into recessed cavity of desk mount housing See Figure 5 13 Install retained desk mount base p
Download Pdf Manuals
Related Search