Chief KPY220B mounting kit
Contents
1. screws K See Figure 11 Cable Path typical Figure 11 ADJUSTMENT ARM PIVOT SWING CAUTION If lock washer G has been used to assemble arms then forced movement of arms without loosening screw H will damage arm and or Y connector See Figure 3 See Figure 5 1 Using 3 16 hex key slightly loosen or tighten the adjustment screw s as necessary See Figure 12 Adjustment Screws Figure 12 Installation Instructions KPY220 HEIGHT ADJUSTABLE IF APPLICABLE IMPORTANT It is important that the mount be attached to the mounting surface AND display be attached to the mount BEFORE attempting to adjust the height adjustable arm 1 Using 5 32 hex key slightly loosen or tighten the adjustment screw as necessary See Figure 13 e If display settles on its own then rotate adjustment screw counterclockwise towards the symbol e If display rises on its own then rotate adjustment screw clockwise towards the symbol NOTE It may be necessary to raise or lower the height adjustable arm to expose the adjustment screw Figure 13 CENTRIS HEAD 1 If previously attached disconnect cables from display then remove display 2 Using Phillips screwdriver slightly loosen or tighten the adjustment screw as necessary See Figure 14 Adjustment Screw Phillips Screwdriver Figure 14 3 Install mount and then display2. 2mm 5x 194x 375 5x 194x 75 d T 4 U 2 V 1 5 16 steel 5 16 plastic 3A e P 23 Installation Instructions KPY220 INSTALLATION INSTALLATION TO POLE 1 Determine approximate location for mount keeping in mind display size extension height adjustment and pitch roll requirements 2 Place Y adapter pole clamp B against pole with pole clamp back C on opposite side of pole See Figure 1 3 Using 5 32 hex key loosely assemble with three 1 4 20x 1 1 4 button head cap screws J See Figure 1 Figure 1 NOTE Equally tighten screws J against Y adapter pole clamp and the pole clamp back C See Figure 2 4 Position mount at desired height and orientation Tighten screws J securely C K e b o aces Keep equal 2 LN S distance between FX H mount and T d clamp when tightening Figure 2 DUAL ARM ASSEMBLY BASIC ASSEMBLY 1 Insert pin E into Y adapter B upper bore See Figure 3 NOTE All parts same for both sides Figure 3 2 Install plasic spacer F or lock washer G as desired on pin E See Figure 3 NOTE Spacer F will allow limited movement of arm assembly A relative to Y adapter B dependent upon tension of screw H Lock washer G will lock arm assembly A to Y adapter B See ADJUSTMENT for detail 3 Insert arm assemb
3. INSTALLATION INSTRUCTIONS Height adjustable Dual Monitor Pole Mount Our Mounts Your Vision CHIEF KPY220 KPY220 Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions DIMENSIONS CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warran
4. as required before proceeding See ADJUSTMENT for detail 2 Carefully place display face down on a clean and dry surface 3 Determine depth of recessed mounting holes relative to back surface of display 4 Select proper length spacer and screw from table below IMPORTANT All spacers used should be the same length If the recess depths result in multiple spacer lengths then select the longer spacer IF recess DEPTH is THEN use spacer AND screw 3 8 or less Q 3 8 long N M4 x 20mm More than 3 8 up to R 3 4 long and including 3 4 M M4 x 30mm 5 Place the four spacers Q or R over each mounting hole on the back of display See Figure 8 6 Orient mount so that mounting holes in the Centris cup are aligned with the holes in the spacers Q or R rotate the Centris cup as required See Figure 8 A CAUTION IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes 7 Using Phillips screwdriver install four screws M or N through the mounting holes in Centris cup through the spacers Q or R into display See Figure 8 8 Tighten all four screws Do not overtighten 9 Return to mount installation section to continue 10 Repeat display installation procedure for second display
5. cables See DISPLAY INSTALLATION KPY220 Installation Instructions 10 Installation Instructions KPY220 11 KPY220 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8832 002035 Rev00 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 07 10 USA International Europe Asia Pacific PTNUPMNUP TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong fo A 852 2145 4099 4 tal 852 2145 4477 Ka D xo RE
6. crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster d y E Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche d O 0 O Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Installation Instructions KPY220 TOOLS REQUIRED FOR INSTALLATION Ae C 1 A 2 B 1 pole clamp back Height adjustable arm Y adapter pole clamp Na F 2 G 2 D 2 E 2 plastic spacer lock washer pivot pin cable management cover H 2 M 2 J 3 K 4 L 2 5 16 18 x 4 1 4 20 x 1 1 4 8 32 x 3 8 5 1 i y P M 8 N 8 P 8 Q 8 R 8 M4x30mm M4x20mm M4x1
7. ly A on pin E See Figure 3 4 While holding nut L in lower bore of Y connector insert screw H through washer T washer U washer T arm assembly A and Y adapter into nut L See Figure 3 Loosely install screw H using 3 16 hex key A CAUTION Improper positioning of arm assembly A may result in failure of mount and subsequent damage to displays Do NOT position either arm assembly A in gray shaded area 5 Position arm assembly A within UNSHADED area as shown See Figure 4 Using 3 16 hex key tighten screw H as required to maintain position KPY220 Installation Instructions DO NOT POSITION EITHER ARM ASSEMBLY IN GRAY SHADED AREA Figure 4 6 Repeat Steps 1 through 5 for second mount arm assembly A 7 If desired proceed to MODIFICATION Otherwise proceed to e CABLE MANAGEMENT for display with RECESSED mounting holes or to e DISPLAY INSTALLATION for all other display configurations MODIFICATION If desired each arm assembly A may be modified to prevent movement of the outer arm relative to the inner arm without loosening the adjustment screw NOTE Spacer shipped configuration will allow limited movement of outer arm relative to inner arm dependent upon tension of screw Lock washer G will lock arms together See ADJUSTMENT for detail 1 Using 3 16 hex key loosen screw until nut can be removed See Figure 5 Retain nu
8. o Q M or N 4 places Q or R 4 places Figure 8 KPY220 Installation Instructions CABLE MANAGEMENT 1 Attach all cables to display 2 Open the cable management bracket by sliding it towards the edge of the arm See Figure 9 NOTE If necessary cable management bracket attach screws may be loosened using 3 32 hex key X E gt da Attach Screws OPEN Position CLOSED Position View from Bottom ch Figure 9 CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched when bracket is closed 3 Carefully insert cables into bracket See Figure 10 Cable Management Bracket in open position Cable Path typical A NOTE Display not shown for clarity Figure 10 4 Close cable managementbracket by sliding it back towards the centerline of the arm See Figure 9 NOTE If necessary cable management bracket attach screws may be tightened using 3 32 hex key X CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched by installation of cover D or screws K 5 Carefully insert cables in cavity located in lower portion of static mount arm See Figure 11 6 Using Phillips screwdriver install cover D with two 8 32 x 3 8
9. t Screw and washers may remain in outer arm Screw amp washers Outer arm Inner arm amp F or ies E L Figure 5 2 Liftouter arm from pin with screw and washers and place on protective surface 3 Remove spacer F from pin See Figure 5 4 Install lock washer G on pin See Figure 5 5 Re install outer arm with screw and washers on pin See Figure 5 6 Insert and hold nut in lower bore of inner arm See Figure 5 7 Tighten screw as required using 3 16 hex key See Figure 5 8 Proceed to CABLE MANAGEMENT for display with RECESSED mounting holes or to DISPLAY INSTALLATION for all other display configurations DISPLAY INSTALLATION The mounting holes on the back of the display will be flush with the back surface or recessed intothe back Refer to the applicable installation procedure below Flush Mount Display Installation CAUTION IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes CAUTION IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris bracket 1 Ensure Cen
10. tris cup is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust de eee before proceeding See ADJUSTMENT for etail 2 Using Phillips screwdriver carefully install two M4x12mm screws P into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns See Figure 6 3 Align two M4x12mm Phillips machine screws P installed on the back of the display in the previous step with the two Ge teardrop mounting holes on the Centris cup See Figure 6 CAUTION IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Smaller area of teardrop mounting holes must be facing downward for proper installation Reposition Centris cup if required Installation Instructions KPY220 Centris Cup Figure 6 4 Using Phillips screwdriver install two M4x12mm Phillips machine screws P through the lower mounting holes in Centris cup into the display See Figure 7 5 Tighten all screws P Do not overtighten See Figure 7 g Centris Cup Figure 7 6 Repeat display installation procedures for second display 7 Proceed to CABLE MANAGEMENT Recessed Mount Display Installation 1 Ensure Centris bracket is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust
11. ty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the KPY220 mount up to and including the displays does not exceed 40 Ibs 18 14 kg pii 183 4 135 19 03 1 TN SZ Installation Instructions KPY220 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au
Download Pdf Manuals
Related Search