EnGenius EOC5611P
Contents
1. SNMP Enable Disable Select the Radio button to Enable or Disable SNMP function Contact Specify the contact details of the device Location Specify the location of the device Community Name Specify the password for access the SNMP community for read only access Community Name Specify the password for access the SNMP community for read and write access Trap Destination IP Specify the IP address that will receive the SNMP trap Address Trap Destination Specify the password of the SNMP trap community Community Name Apply Cancel Press Apply to apply the changes or Cancel to return previous settings 54 8 4 Management Backup Restore Settings Click on the Backup Restore Setting link under the Management menu This option is used to save the current settings of the device in a file on your local disk or load settings on to the device from a local disk This feature is very handy for administrators who have several devices that need to be configured with the same settings Backup Restore Settings NN Save A of Current Click on Backup to save current configured settings Settings Restore Saved Settings EOC5611P can restore a previous setting that has been saved Click on Browse to from a File select the file and Restore Revert to Factory Default Click on Factory Default button to reset all the settings to the default values Settings 52. r agga _ maag IP Network Setting Select Radio button for Obtain an IP address automatically or Specify an IP address IP Address Specify LAN port IP address IP Suet Mask Specify Subnet Mask Default Gateway Specify Default Gateway Primary DNS Specify Primary DNS Secondary DNS Specify Secondary DNS Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction Obtain an IP address automatically is not a DHCP server It means automatically get IP address when device connected to a device or services which has DHCP server 30 5 2 System gt Spanning Tree Settings Spanning Tree Settings Spanning Tree Status Select the Radio button to On or Off Spanning Tree function Bridge Hello Time Specify Bridge Hello Time in second Bridge Max Age Specify Bridge Max Age in second Bridge Forward Delay Specify Bridge Forward Delay in second Priority Specify the Priority number Smaller number has greater priority Apply Cancel Press Apply to apply the changes or Cancel to return previous settings 31 6 Router Settings This section is only available for AP Router Mode and Client Router Mode 6 1 Router gt WAN Settings There are four different types of WAN connection Static IP DHCP PPPoE and PPTP Please contact your ISP to select the connection type 6 1 1 WAN Settings gt Static IP
3. PORT FORWARDING e Fere ev rooted eere eee ewe e D ee e be Fade ever ed pev Even 43 7 INFORMATION STATUSi 1 44 VAGUE 44 7 2 STATUS WIRELESS CLIENT 46 TS STATUS SYSTEM LOG g ua n L n L U atc Ceca Pee ele eee ep eie cerei eve Pese UN 47 JA STATUS WDS EINKSTATUS ics eot rectae Een eo Sus EE YR ee ERE TUN OVE PUE Pe EP EATER uyu sarasa 48 7 5 STATUS CONNECTION STATUS uu pe b Peer er bir pe bcp T e Per der eben Ure pea Eb reb eiue v Eb EE 49 Z o STATUS S 2 HEI i Cle dee eh D Ee eder CU GERE E eL PL dr E TELE DE Ede HEEL 50 8 neam ueaaulicee E 51 8 1 MANAGEMENT ADMINISTRATION c sese nennen nennen e sete S sess en ense eese es esee 51 8 2 MANAGEMENT MANAGEMENT VLAN 53 8 3 MANAGEMENT gt SNMP SETTINGS i ize che Ee Ea a edet EDD 54 8 4 MANAGEMENT gt BACKUP RESTORE SETTINGS ccsssscceessscecsssseceessssecessessccssseceessssecessessccssseceesussscesssscecsssscecsasescessasens 55 8 5 MANAGEMENT FIRMWARE UPGRADE heme e nennen enes enne rn hse eset r ense 56 8 6 MANAGEMENT gt TIME SETTINGS l rre
4. environment 9 1 Access Point 192 168 1 1 Client 192 168 1 12 EOC5611P sso1 it Client 192 168 1 11 192 168 1 10 Ethernet I g f Client Access Point Step1 Login to the web based configuration interface with default IP 192 168 1 1 Step2 Select your country or region s regulation Step3 802 11a b g wireless network Step4 Use site survey to scan channels that have been used in nearby area Step5 Select channel with less interferences Specify the SSID for your broadcast SSID and you can also configure multiple SSID at codi the same time Step7 Verify VLAN identifier to separate services among clients Step8 Setup the authentication settings Step9 Press Apply to save all changes Note For more advanced settings please refer to the previous chapters Wireless Client Step1 Select wireless mode you would like to associate with Step2 Use site survey to scan nearby Access Point and select the certain AP you would like 60 to connect with or enter SSID manually Step3 Configure VLAN ID in your wireless device if available Step4 Select correct authentication type and password Auction EOC5611P s Access Point Mode does not provide DHCP server so the Wireless Client IP address must configure manually at the same subnet in Local Area Network 9 2 Client Bridge Mode Client Bridge Mode functions like a wireless dongl
5. In either case network performance can suffer 38 6 1 4 WAN Settings gt PPTP Point to Point Tunneling Protocol Select PPTP as your WAN connection type if your ISP provides information about IP Address Subnet Mask Default Gateway Optional DNS Optional Server IP Username and Password WAN Settings QUOTE Reset Ping Internet Connection Select PPTP to begin configuration of the PPTP connection 39 MTU Specify the Maximum Transmit Unit size Suggest remain in Auto IP Address Specify WAN port IP address IP Subnet Mask Specify WAN IP Subnet Mask Gateway IP Address Specify WAN Gateway IP address PPTP Server Specify PPTP Server IP address Username Specify the Username that is given by your ISP Password Specify the Password that is given by your ISP Connect on Demand Select the Radio button to specify the maximum idle time Internet connection will disconnect when it reach the maximum idle time but it will automatically connect when user tries to access the network Keep Alive Select the Radio button to keep internet connection always on Specify the redial period once the internet lose connection Get Automatically From ISP Select the Radio button for get the DNS automatically from DHCP server Use These DNS Servers Select the Radio button for setup the Primary DNS and Secondary DNS servers manually Discard Ping on
6. Select Static IP in WAN connection if your ISP gives all the information about IP address Subnet Mask Default Gateway Primary DNS and Secondary DNS 32 WAN Settings Options Home Reset Auto 1500 Internet IP Address Domain Name Server DNS Address Internet Connection Type Select Static IP to begin configuration of the Static IP connection Account Name Specify Account Name that is provided by ISP Domain Name Specify Domain Name that is provided by ISP MTU Specify the Maximum Transmit Unit size Suggest remain in Auto IP Address Specify WAN port IP address IP Subnet Mask Specify WAN IP Subnet Mask Gateway IP Address Specify WAN Gateway IP address Primary DNS Specify Primary DNS IP Secondary DNS Specify Secondary DNS IP Discard Ping on WAN Place a Check to Enable or Disable ping from WAN Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction If the router s MTU is set too high packets will be fragmented downstream If the router s 33 MTU is set too low the router will fragment packets unnecessarily and in extreme cases may be unable to establish some connections In either case network performance can suffer 34 6 1 2 WAN Settings gt DHCP Dynamic IP Select DHCP as your WAN connection type to obtain your IP address automatically You will need to
7. enter Account Name as your hostname and DNS Optional WAN Settings Home ewe e Options Domain Name Server DNS Address WAN Ping Discard Pigon WAN Internet Connection Type Select DHCP to begin configuration of the DHCP connection Account Name Specify Account Name that is provided by ISP Domain Name Specify Domain Name that is provided by ISP MTU Specify the Maximum Transmit Unit size Suggest remain in Auto Get Automatically From Select the Radio button for get the DNS automatically from DHCP server ISP Use These DNS Servers Select the Radio button for setup the Primary DNS and Secondary DNS servers manually Discard Ping on WAN Place a Check to Enable or Disable ping from WAN 35 Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction If the router s MTU is set too high packets will be fragmented downstream If the router s MTU is set too low the router will fragment packets unnecessarily and in extreme cases may be unable to establish some connections In either case network performance can suffer 36 6 1 3 WAN Settings gt PPPoE Point to Point Protocol over Ethernet Select PPPoE as your WAN connection type if your ISP provides Username and Password PPPoE is a DSL service and please remove your PPPoE software from your computer the software is not worked in EOC5611P WA
8. 11a b g wireless network Step5 Select channel you would like to use Step6 Setup the authentication settings Step7 Setup WDS Link Settings Step8 Specify the AP s MAC address you would like to connect with Step9 Press Apply to process all the configurations Auction Each WDS bridge s device must use the same Subnet Wireless Mode Wireless Channel and Security Setting 9 4 Client Router In the Client Router Mode the EOC5611P has DHCP Server build inside that allows many LANs automatically generate an IP address to share the same Internet Connect an AP WISP Wirelessly and connect to LANs via wired Client Router Mode is act completely opposite to the AP Router Mode 62 192 168 190 E 192 168 141 7 WISP 5611 19216812 A 192 168 1 1 PC Please refer to the last section to check Access point s configuration Client Router Step1 Login to the web based configuration interface with default IP 192 168 1 1 Step2 Select your country or region s regulation Step3 Select Operation Mode to Client Router from System Properties Step4 Change your Local Area Network setting to Obtain an IP Address Automatically Step5 802 11a b g wireless network Step6 Use site survey to scan Access Points that are available in nearby area Step7 Select the AP you would like to associate with Step8 Setup the authentication settings that match to the Access Point s setting
9. Mode Off Service Name Specify a name for current Port Forwarding rule Protocol Select a protocol from drop down list Both TCP and UDP Starting Port Specify Starting Port number Ending Port Specify Ending Port number 43 IP Address Specify IP address Save Cancel Press Save to apply the changes or Cancel to return previous settings 7 Information Status Status section is on the navigation drop down menu You will then see three options Main Wireless Client List System Log WDS Link Status Connection Status and DHCP Client Table Each option is described in detail below 7 1 Status Main Click on the Main link under the Status drop down menu or click Home from the top right of the webpage The status that is displayed corresponds with the operating mode that is selected Information such as operating mode system up time firmware version serial number kernel version and application version are displayed in the System section LAN IP address subnet mask and MAC address are displayed in the LAN section In the Wireless section the frequency channel is displayed Since this device supports multiple SSIDs the details of each SSID such as ESSID and its security settings are displayed 44 System Information uw 4 Current Wireless Settings 7 2 Status Wireless Client List Click on the Wireless Client List link under the Status drop down menu This page displays the li
10. Physical Interface 1 x 10 100 Fast Ethernet RJ 45 1 x Reset Button 1 x Antenna Switch Internal and External Switch 2 x SMA Connector One is for 2 4GHz and another is for 5GHz LED indicators Power Status LAN 10 100Mbps WLAN Wireless is up 3 x Link Quality Client Bridge mode Green Good Quality Yellow Marginally Acceptable Quality 6 Red Bad Quality Power Requirements Active Ethernet Power over Ethernet Proprietary PoE design Power Adapter 24V 1A DC Regulation Certifications Part 15C 15B 15E EN301 893 EN 300 328 EN 301 489 1 17 EN60950 IC Certification 2 EOC5611P Multi Function Instruction Guide 2 1 Access Point In the Access Point Mode with WDS Function EOC5611P function likes a central connection for any stations or clients that support IEEE 802 11a b g network Stations and Client must configure the same SSID and Security Password to associate within the range EOC5611P supports 4 different SSIDs to separate different clients at the same time Client LN 5502 E emf 5501 Client Client SSIES 6 5611 Ethernet l p mtl 3 Client Client 2 2 Access Point with WDS Function EOC5611P also supports WDS function in Access Point Mode without losing AP s capabilities Configure others Access Point s Wireless MAC Address in both Access Point devices to enlarge the wireless area by enabl
11. Rate Select Data Rate from the drop down list Data rate will affect the efficiency of the throughput If the data rate is set to a small number the lower through will get but it can transmit to longer distance Transmit Power Select Transmit Power to increase or decrease Transmit Power Higher transmit power will sometimes cause unable to connect to the network On the other hand the lower transmit power will cause client unable to connect to the device Antenna Select antenna waveform from Diversity Vertical or Horizontal Fragment Length Specify package size during transmission If large amount of client are accessing to the network specify small number of the fragment length in order to avoid collision RTS CTS Threshold Specify Threshold package size for RTC CTS Using small number of the threshold will cause RTS CTS packets to be sent more often to consuming more of the available bandwidth In addition if the heavy load traffic occurs the wireless network can be recovered easily from interferences or collisions Protection Mode Select Disable or Enable Protection Mode If there are large amount of error occur during the transmission please enable the protect mode otherwise protect mode should remain disable WMM Select Disable or Enable WMM function WMM is based on the four Access Categories voice video best effort and background WMM function is not used to guarantee transmissi
12. Step9 Setup your WAN connection type given by your Internet Service Provider from WAN Settings Step10 Press Apply to process all the configurations Auction Client Router s IP setting must match to the Access Point s subnet 63 10 VLAN CONFIGURATION GUIDE Following procedures are used to configure VLAN on EnGenius product EnGenius product supports both wireless and wired tagging on your network Wireless tagging can help you to divide the permission for different group of users Wireless Clients associated with SSID1 4 will not have the authority to manage the device when you enable the Profile Isolation except the Wireless VLAN ID is the same as Management VLAN ID Enable Profile Isolation will also restrict the communication between wireless clients with different group of Wireless VLAN ID Management VLAN Wired is used to manage your device if the computer has authorized VLAN ID Following are VLAN configuration procedures Connect a PC to EnGenius product to LAN port with an IP address like 192 168 1 100 255 255 255 0 which is located within same subnet of EnGenius product LAN port IP address and then open any popular WEB browser at http 192 168 1 1 Blank Page Windows Internet Explorer 192 168 1 1 1 Enter admin for both default Username and Password or enter your own Username and Password Windows Security The server 192 168 1 1 at requires a username and password Warning This server is requesting that
13. eno eee ayau r I G w eee 57 S MANAGEMENT 06 aS O 58 8 8 gt DIAGNOSTICS iiri tt E Ere Ree coe e eder Cr eere bb be Ere coe Se e PERPE eade 59 9 NETWORK CONFIGURATION EXAMRPIE 60 9 1 ACCESS POINT sss rc rtr beer tee eee ee Rose ede Te eco tes ei Tai evade Aneta OE deel EO Pe 60 9 2 CUENT BRIDGE MODE rr erret peek elo to ANE u E OE ENTRE ERR 61 9 3ANDS BRIDGE MODE irre Pert A e 61 9 5 EP PRU EE EU SO HU EL Tte ETC Ee n e D Pe Hd CO OE LEE P LOEO 62 10 VLAN CONFIGURATION fcitp EE 64 APPENDIX A FCC INTERFERENCE STATEMENTT A 68 1 Product Overview Thank you for using EOC5611P It is a powerful enhanced enterprise scale product with 4 1 multi functions Access Point Access Point with WDS function Client Bridge WDS Bridge and Client Router EOC5611P is easily to install almost anywhere with Power over Ethernet for quick outdoor installation External N type antenna provides better wireless signal quality and the antenna is
14. security settings 4 3 1 WEP g 4 Open System 40 64 bit 10 hex digits or 5 ASCII char i Security Mode Select WEP from the drop down list to begin the configuration Auth Type Select Auth Type in Open System or Shared Input Type Select Input Type in Hex or ASCII Key Length Select Key Length in 64 128 152 bit password length Default Key Select the default index key for wireless security Key1 Specify password for security key index No 1 Key2 Specify password for security key index No 2 Key3 Specify password for security key index No 3 Key4 Specify password for security key index No 4 20 4 3 2 WPA PSK Wireless Security Security Mode Select WPA PSK from the drop down list to begin the configuration Encryption Select Auto TKIP or AES for Encryption type Passphrase Specify the security password Group Key Update Interval Specify Group Key Update Interval time Group Key Update Timeout Specify Group Key Update Timeout time Pairwise Key Update Interval Specify Pairwise Key Update Timeout time 4 3 3 WPA2 PSK Wireless Security Select WPA2 PSK from the drop down list begin the configuration 21 Encryption Select Auto TKIP or AES for Encryption type Passphrase Specify the security password Group Key Update Interval Specify Group Key Update Interval
15. the Radio Button to allow deny client to communicate each other Wireless Security Please refer to the Wireless Security section Save Cancel Press Save to save the changes or Cancel to return previous settings Note When you enable Profile Isolation all the packets transmit through wireless network will carry VLAN ID 15 4 2 2 Client Bridge Mode Wireless Network Wireless Network Home Reset Wireless Mode 802 1 1a 5GH2S4Mbps WoS Client Enable Disable Wireless Mode EOC5611P supports 802 11a b g wireless band SSID Specify the SSID if known SSID text box will be automatically fill in when select an AP in the Site Survey Site Survey Using Site Survey to scan nearby APs and then select the AP to establish the connection Prefer BSSID Specify the MAC address if known Prefer BSSID text box will be automatically fill in when select an AP in the Site Survey WDS Client Place a Radio button to Enable Disable WDS Client Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Site Survey 5GHz Site Survey Infrastructure hoc SSD Securty Network Mode Profile After Site Survey webpage will display all nearby area s Access Point Click the BSSID if you would like to connect with it Wireless Security Please refer to the Wireless Security section Refresh Press Refresh to scan aga
16. time Group Key Update Timeout Specify Group Key Update Timeout time Pairwise Key Update Interval Specify Pairwise Key Update Timeout time 4 3 4 WPA PSK Mixed Wireless Security Security Mode Select WPA PSK Mixed from the drop down list to begin the configuration Encryption Select Auto TKIP or AES for Encryption type Passphrase Specify the security password Group Key Update Interval Specify Group Key Update Interval time Group Key Update Timeout Specify Group Key Update Timeout time Pairwise Key Update Interval Specify Pairwise Key Update Timeout time Auction WPA PSK Mixed means it allow both WPA PSK and WPA2 PSK security types to establish wireless connection 22 4 3 5 WPA WPA security mode is for 802 1x authentication You must provide a RADIUS Server to check the permission of access the network 415 4 1812 Disable Security Mode Select WPA from the drop down list to begin the configuration Encryption Select Auto TKIP or AES for Encryption type Radius Server Specify Radius Server IP Address Radius Port Specify Radius Port number the default port is 1812 Radius Secret Specify Radius Secret that is given by the Radius Server Group Key Update Specify Group Key Update Interval time Interval Group Key Update Specify Group Key Update Timeout time Timeout Pairwise Key Update Speci
17. upgradeable EOC5611P uses 5G band and 2 4G wireless signal to avoid interference of most digital signal such as mobile phone EOC5611P can manage power level control Narrow bandwidth selection Traffic shaping and Real time RSSI indicator EOC5611P is fully support of security encryption including WI Fi Protected Access WPA PSK WPA2 PSK 64 128 152 bit WEP Encryption and IEEE 802 1x with RADIUS Accounting Auction The internal antenna is only available for 5G band wireless network 1 1 Feature The following list describes the design of the EOC5611P made possible through the power and flexibility of wireless LANs a Difficult to wire environments There are many situations where wires cannot be laid easily Historic buildings older buildings open areas and across busy streets make the installation of LANs either impossible or very expensive b Temporary workgroups Consider situations in parks athletic arenas exhibition centers disaster recovery temporary offices and construction sites where one wants a temporary WLAN established and removed c The ability to access real time information Doctors nurses point of sale employees and warehouse workers can access real time information while dealing with patients serving customers and processing information d Frequently changed environments Show rooms meeting rooms retail stores and manufacturing sites where frequently 3 rearrange the workplace e Wireless exten
18. your username and password be sent in an insecure manner basic authentication without a secure connection r Mj 3 Remember my credentials 64 2 Press Wireless Network to configure Wireless VLAN Wireless Network tomer Euge 3 To configure Wireless VLAN Tagging please press Edit at Wireless Network section Wireless Network o 802 1 b g Mixed 4 v Chl 2412GHz v P 4 After Press Edit web should pop out a window as below You may enter your desire VLAN ID Then Ret 5 Wireless Network webpage should have display all the VID as below If you would like to enable Wireless VLAN function select the radio button of Isolate all Profiles from each other using VLAN standard and then press Apply to configure the changes Note Any Wireless clients associated with SSID1 to 55104 cannot access to the management page unless its Wireless VLAN ID is the same as the Management VLAN ID Enable Profile Isolation will also deny the communication between different groups of VID Wireless Network 802 11 bg Mixed QGHz 4Mbps v Chl 2 412GH2 v 7 B 2 3 d Auction If you would like to use 802 1 x authentications WPA WPA2 WPA Mixed with VLAN tagging you must enable Management VLAN For more details please follow the instruction below 66 6 Press Management VLAN to c
19. 5 8 5 Management Firmware Upgrade Click on the Firmware Upgrade link under the Management menu This page is used to upgrade the firmware of the device Make sure that downloaded the appropriate firmware from your vendor Firmware Upgrade Ung Upgrade Auction Upgrade process may take few minutes please do not power off the device and it may cause the device crashed or unusable EOC5611P will restart automatically once the upgrade is completed 8 6 Management gt Time Settings Click on the Time Settings link under the Management menu This page allows you to configure the time on the device You may do this manually or by connecting to a NTP server Time Settings Home Reset LI n leis p go go 77 Manually Set Date Time Manually setup the date and time Automatically Get Date and Time Specify the Time Zone from the drop down list and Place a Check to specify the IP address of the NTP Server manually or uses default NTP Server Apply Cancel Press Apply to apply the changes or Cancel to return previous settings 57 8 7 Management Log Click on the Log link under the Management menu The Log page displays a list of events that are triggered on the Ethernet and Wireless interface This log can be referred when an unknown error occurs on the system or when a report needs to be sent to the technical support department fo
20. Client Router Mode Wireless Network Wireless Network Home Reset 802 11a 5GHz 4Mbps gIIIII Wireless Mode EOC5611P supports 802 11a b g wireless band SSID Specify the SSID if known SSID text box will be automatically fill in when select an AP in the Site Survey Site Survey Using Site Survey to scan nearby APs and then select the AP to establish the connection Prefer BSSID Specify the MAC address if known Prefer BSSID text box will be automatically fill in when select an AP in the Site Survey WDS Client Place a Radio button to Enable Disable WDS Client Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Site Survey 5GHz Site Survey infrastructure hoc BSSD SSD Network Mode eie Profile After Site Survey webpage will display all nearby area s Access Point Click the BSSID if you would like to connect with it Wireless Security Please refer to the Wireless Security section Refresh Press Refresh to scan again Auction If the Access Point is suppressed its owned SSID SSID section will be blank the SSID must be 19 filled in manually 4 3 Wireless Security Settings Wireless Security Settings section will guide you to the entire Security modes configuration WEP WPA PSK WPA2 PSK WPA PSK Mixed WPA WPA2 and WPA Mixed We strongly recommend that uses WPA2 PSK as your
21. N Settings 555 Options n PPPoE Options D WAN Ping Internet Connection Type Select PPPoE to begin configuration of the PPPoE connection MTU Specify the Maximum Transmit Unit size Suggest remain in Auto Login Specify the Username that is given by your ISP Password Specify the Password that is given by your ISP Service Name Specify the Service Name that is given by your ISP 37 Connect on Demand Select the Radio button to specify the maximum idle time Internet connection will disconnect when it reach the maximum idle time but it will automatically connect when user tries to access the network Keep Alive Select the Radio button to keep internet connection always on Specify the redial period once the internet lose connection Get Automatically From ISP Select the Radio button for get the DNS automatically from DHCP server Use These DNS Servers Select the Radio button for setup the Primary DNS and Secondary DNS servers manually Discard Ping on WAN Place a Check to Enable or Disable ping from WAN Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction If the router s MTU is set too high packets will be fragmented downstream If the router s MTU is set too low the router will fragment packets unnecessarily and in extreme cases may be unable to establish some connections
22. OPERTIES enne ener nennen nennen nennen 13 4 2 WIRELESS SETTINGS erret rrr E REFLECTS EM HERR TRO Re FER RR 14 4 2 1 Access Point Mode Wireless Network nnne 14 4 2 2 Client Bridge Mode gt Wireless Network eene enne 16 4 2 3 WDS Bridge Mode gt Wireless Network n nn nsn sss 17 4 2 4 Client Router Mode Wireless Network 19 4 3 WIRELESS SECURITY SETTINGS P decor ee ME Petites 20 23 1 WEP sS d ade eite a eere eee er Gir UR SS QR ism eI eei ri 20 43 2 WPAZPSK c iibi o eem dre eibi eph 21 4 3 3 WPA2 PSK iioii E EE a ha e Eh coon PRINT EIER ee deeds ER 21 4 3 4 WPA PSK Mixed siete ieii nein ree rikiai de 22 AS SW PA REO e USER EY ES E Oe E EV expe EU re RE ER ER Te ERE 23 43 6 WPA2 iir tete d ume hu enhn aud UE s LEE E 24 WPA s aa S tente teda eae nie et 25 4 3 8 RAGIUS ACCOUNTING 26 4 4 WIRELESS WIRELESS ADVANCED SETTINGS ccsccesceesceesceseesteeseceseesaecnaecnaecnecscesseesseeesecaeenaeeeaeenaecaeecae
23. P Pass Through L2TP Pass Through V IPSec Pass Through PPTP Pass Through Place a Check to enable PPTP protocol passes through WAN L2TP Pass Through Place a Check to enable L2TP protocol passes through WAN IPSec Pass Through Place a Check to enable IPSec protocol passes through WAN Apply Cancel Press Apply to apply the changes or Cancel to return previous settings 42 6 4 Router gt Port Forwarding Port Forwarding is used to allow a public service such as Web Server Mail Server and FTP server to be set up For example Set up a Web Server on your computer with port number 8080 Visitor on the internet can access your Web Server by entering WAN Port IP with port number 8080 If your WAN Port IP is 192 168 5 1 then visitor must enter http 192 168 5 1 8080 To find out more the well known port numbers please search the internet Port Forwarding _ Home Reset Protocol StartPort EndPort Serverip Address Enable Modify Delete Add Apply Add Entry Press Add Entry to add a rule of Port Forwarding Apply Press Apply to apply the changes httpy 192 168 1 1 setup lt gitregfile html PortAdd htm amp edidx 0 S http 192 168 41 4 setup cgi regfile html PortAdd htm amp edidx Port Forwarding Service Name Protocal BOTH Starting Port 1 65535 Ending Port 1 655535 IP Address I Internet Protected
24. WAN Place a Check to Enable or Disable ping from WAN Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction If the router s MTU is set too high packets will be fragmented downstream If the router s MTU is set too low the router will fragment packets unnecessarily and in extreme cases may be unable to establish some connections In either case network performance can suffer 40 6 2 Router gt LAN Settings LAN Settings LAN IP Setup _ PTT Use Router As DHCP Server _ auma ia IP Address Specify LAN port IP address IP Subnet Mask Specify LAN IP Subnet Mask WINS Server IP Specify WINS Server IP Use Router As DHCP Place a Check to enable DHCP server Server Starting IP Address Specify DHCP server starting IP address Ending IP Address Specify DHCP server ending IP address Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction If you uncheck the DHCP Server function you must configure you IP Address manually The instruction please refers to the Computer Settings section 41 6 3 Router VPN Pass Through VPN Pass Through is used to allow certain protocol to be tunneled through an IP network such as PPTP and L2TP or implement secure exchange of packets at the IP Layer such as IPSec VPN Pass Through Home 2 Reset PPT
25. Wireless Outdoor Client Bridge Access Point EOC5611P EnGenius EOC56411FEF 802 11a b g User Manual Version 1 0 Table of Contents 1 PRODUCT OVERVIEW xu u C 3 NI E dE 3 1 2 BENEFITS ase 5 1 3 PACKAGE CONTENTS Qa O MR REP ERROR RR EPOR REOR FERRE ER EE EFE EORR 6 1 4 SYSTEM REQUIREMENT rti tee GER ETE ERR tes GERE SERERE E Me E E ER ER RU e HERE et n eh 6 1 5 HARDWARE OVERVIEW 5 72 3 e rece RD e e REI e DUE REI Te EFIE Te Pei o E NEUE OUR 6 2 EOC5611P MULTI FUNCTION INSTRUCTION GUIDE 8 pz usiidde e 8 2 2 ACCESS POINT WITH WDS FUNCTION cote bre ESPERE AN eic btt d vaio eve 8 2 3 CLIENT BRIDGE re ER ED DO ISO EUER bodes sabe ap UD CORE aa Sp aa 9 2 4 WDS BRIDGE RW RR OX EEUU ER RA RW ER KR GU UR GUERRERO 9 2 5 CLIENT ROUTER wisn sei E Ee 10 S COMPUTER SETTINGS 22s S AS a eoe Q SSS Q Q S SSS uQ qS SSS S L Sa mu S 11 B LASSIGNASTATIGIP EE 11 3 2 LOGGING e tette eet ee eee feeder due eee eei e te teme nana reed i 12 4 WIRELESS dmupicrfewe e sassa 13 4 1 SWITCHING OPERATION MODE SYSTEM SYSTEM PR
26. d cost savings EOC5611P must uses the adapter provided in the package Allow clients to access different networks through a single access point and assign different policies and functions for each SSID by manager Fully support all types of security types Ensures secure network connection Easy to access internet via ISP service authentication Help administrators to remotely configure or manage the Access Point easily Enhance user performance and density 1 2 Benefits Access Point Mode Use this feature to setup the access point s configuration information It has support adjusting transmit power and channel Client can access the network with different regulatory settings and automatically change to the local regulations Client Bridge Mode Use this feature to connect to an Access Point and enjoy the great speed of surfing internet WDS Bridge Mode Use this feature to link multiple APs in a network All clients associated with any APs can communicate each other like an ad hoc mode Client Router Mode This feature functions completely opposite but similarly with AP Router Mode Client Router connected to an AP wirelessly and transmits internet connection protocol through AP to access the internet Multiple SSIDs EOC5611P supports up to 4 SSIDs on your access point The following options can be set to each SS to each SSID SSID for public or private network Authentication is fully supp
27. e It must connect to an Access Point AP Router to join the network 192 168 1 10 EOC5611P Access Point 192 168 1 1 Wireless Router 192 168 1 2 Please refer to the last section to check Access point s configuration Client Bridge Step1 Login to the web based configuration interface with default IP 192 168 1 1 Step2 Select your country or region s regulation Step3 Select Operation Mode to Client Bridge from System Properties Step4 802 11a b g wireless network Step5 Use site survey to scan Access Points that are available in nearby area Step6 Select the AP you would like to associate with Step7 Setup the authentication settings that match to the Access Point s setting Step8 Press Apply to process all the configurations Auction Client Bridge s IP setting must match to the Access Point s subnet 9 3 WDS Bridge Mode Use this feature to link multiple APs in a network All clients associated with any APs can communicate each other like an ad hoc mode 61 Client b Client EOC5611P 5 EOC5611P 192 168 1 2 1 192 168 1 4 WDS 2 5611 ps 192 168 1 1 EOCS611P EOC5611P mI Client 192 168 1 3 192 168 153 capot WDS Bridge Step1 Login to the web based configuration interface with default IP 192 168 1 1 Step2 Select your country or region s regulation Step3 Select Operation Mode to WDS Bridge from System Properties Step4 802
28. e by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter 68
29. each client is displayed Click on the Refresh button to refresh the client list DHCP Client List 50 8 Management Settings Management section is on the navigation drop down menu You will then see seven options administration management VLAN SNMP settings backup restore settings firmware upgrade time settings and log Each option is described below 8 1 Management Administration Click on the Administration link under the Management menu This option allows you to create a user name and password for the device By default this device is configured with a user name and password admin For security reasons it is highly recommended that you create a new user name and password Administration Home Administrator Name Specify Username for login Password Specify a Password for login Confirm Password Re enter the Password for confirmation Remote Access Remote Management Enable Disable Remote Upgrade Enable Disable 8 Remote Management Select the Radio button to Enable or Disable Remote Management 51 Remote Upgrade Select the Radio button to Enable or Disable Remote Upgrade Remote Management Specify the Port number for Remote Management For example If you specify the Port Port number is 8080 then you will need to enter following http IP address 8080 to acce
30. fy Pairwise Key Update Timeout time Interval Radius Accounting Select Enable or Disable Radius Accounting The detail of Radius Accounting is at next section 23 4 3 6 WPA2 security mode is for 802 1x authentication You must provide a RADIUS Server to check the permission of access the network Wireless Security WR E ee ON GN J Security Mode Select WPA2 from the drop down list to begin the configuration Encryption Select Auto TKIP or AES for Encryption type Radius Server Specify Radius Server IP Address Radius Port Specify Radius Port number the default port is 1812 Radius Secret Specify Radius Secret that is given by the Radius Server Group Key Update Interval Specify Group Key Update Interval time Group Key Update Specify Group Key Update Timeout time Timeout Pairwise Key Update Specify Pairwise Key Update Timeout time Interval Radius Accounting Select Enable or Disable Radius Accounting The detail of Radius Accounting is at next section 24 4 3 7 WPA Mixed WPA Mixed security mode is for 802 1x authentication You must provide a RADIUS Server to check the permission of access the network Wireless Security j ao masa ma Security Mode Select WPA Mixed from the drop down list to begin the configuration Encryption Select Auto TKIP or AES for Encryption type Radiu
31. in Auction If the Access Point is suppressed its owned SSID SSID section will be blank the SSID must be 16 filled in manually 4 2 3 WDS Bridge Mode Wireless Network Wireless Network a Wireless Mode EOC5611P supports 802 11a b g wireless band Channel Frequency The channel availability is based on the country s regulation Apply Cancel Press Apply to apply the changes or Cancel to return previous settings WDS Link Settings Home Reset wD MEMdes Mode ENN EF FI EE EAE EN ENN EF EF EFE E ENN EF EF F FIG HEN ENN EF EFI EE EE ENN EF EF EI EE ENN NF EF F JF ENN EF EF F HEN ENN EF EF EI EE ENN EF EF EI OE E NEN ENN EF EF EI EI EE ENN NF EF F FIF ENN EF RE EE EN ENN EF EF F F HEN Was ENN EF FE EG NEN Was ENN EF FE 1 ES _ ENN EJ EF EH JE UJ MAC Address Enter the Access Point s MAC address that you would like to extend the wireless area into the MAC address filter Mode Select Disable or Enable from the drop down list Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction The Access Point that you would like to extend the wireless area must enter your Access Point s MAC address Not all Access Point supports this feature More WDS bridges connected together may cause lower performance 18 4 2 4
32. ing WDS Link Settings WDS function can support up to 8 different AP s MAC addresses Auction Not every Access Point device has support WDS in Access Point Mode It is recommended using EOC5611P if you would like to use this service WDS Client c gc gt Client p a Client EOC5611P EOC5611P enm p 2 3 Client Bridge In the Client Bridge Mode the EOC5611P function likes a wireless dongle Connected to an Access Point wirelessly and surf internet whenever you want Using Site Survey to scan all the Access Point within the range and configure its SSID and Security Password to associate with it Connect you station to the LAN port of the EOC5611P via Ethernet Client Internet EOC5611P Access Point Wireless Router 2 4 WDS Bridge In the WDS Bridge Mode the EOC5611P can wirelessly connect different LANs by just simply configure each other s MAC Address and Security Settings This mode is used when two wired LANs locate in small distance and want to communicate each other The best solution is using EOC5611P wirelessly connect two wired LANs WDS Bridge Mode can establish 16 WDS links The connection diagram is like a Star Auction WDS Bridge Mode is not function like Access Point APs linked by WDS are using the same frequency channel more APs connected together may lower throughput Please be aware to avoid loop connection otherwise you may enable Spanning Tree Function af u Clie
33. n the list or Allow MAC in the list from the drop down list MAC Address Filter Specify the MAC address manually Add Press Add to add the MAC address in the table Apply Press Apply to apply the changes 28 4 6 Wireless gt WDS Link Settings WDS Link Settings is used to establish a connection between Access Points but the device is not losing Access Point function AP has WDS function can extend the wireless coverage and allow LANs to communicate each other Home 5 E x We F 4 BE 4 SIE 4 4 4 i i MAC Address Enter the Access Point s MAC address that you would like to extend the wireless area Mode Select Disable or Enable from the drop down list Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction The Access Point that you would like to extend the wireless area must enter your Access Point s MAC address Not all Access Point supports this feature 29 5 LAN Settings This section will guide you to the Local Area Network LAN settings 5 1 System 2 IP Settings This section is only available for Non Router Mode IP Settings allows you to LAN port IP address of the EOC5611P Auction Changing LAN IP Address will change LAN Interface IP address Webpage will automatically redirect to the new IP address after Apply IP Settings Home rr
34. nt Client E E EOC5611P EOC5611P 2 WDS WDS WDS WDS 5611 pe EA 5611 5611 gt Client Client 2 5 Client Router In the Client Router Mode the EOC5611P has DHCP Server build inside that allows many LANs automatically generate an IP address to share the same Internet Connect an AP WISP Wirelessly and connect to LANs via wired Client Router Mode is act completely opposite to the AP Router Mode K F PC 1 PC 2 f WISP EOC5611P g 10 3 Computer Settings 3 1 Assign a Static IP In order to configure EOC5611P please follow the instruction below 1 In the Control Panel double click Network Connections and then double click on the connection of your Network Interface Card NIC You will then see the following screen 2 Select Internet Protocol TCP IP and then click on the Properties button This will allow you to configure the TCP IP settings of your PC Notebook 3 Select Use the following IP address radio button and then enter the IP address and subnet mask Ensure that the IP address and subnet mask are on the same subnet as the device 4 Click on the OK button to close this window and then close LAN properties window Local Area Connection Properties General Authentication Advanced Connect using Hi Intel 8255x based PCI Ethernet This connection uses the following items M E Client for Microsoft Ne
35. on speed Channel Bandwidth Select Channel Bandwidth from the drop down list Decrease channel bandwidth may cause lower throughput but less collision Distance Specify distance rage between AP and Clients Longer distance may lose high connection speed Wireless Traffic Shaping Place a Check to enable Wireless Traffic Shaping function Incoming Traffic Limit Specify the wireless transmission speed for downloading Outgoing Traffic Limit Specify the wireless transmission speed for uploading Auction Changing Wireless Advanced Settings may cause insufficient wireless connection quality Please remain all settings as default unless you have acknowledged all changing that you have made Note The Internal Antenna is only work for 5GHz wireless network If you would like to use 2 4GHz wireless network you must connected an External Antenna and switch the antenna types from the bottom of the device Close to the Ethernet Port 27 4 5 Wireless gt Wireless MAC Filter Wireless MAC Filters is used to Allow or Deny wireless clients by their MAC addresses accessing the Network You can manually add a MAC address to restrict the permission to access 5611 The default setting is Disable Wireless MAC Filters Wireless MAC Filter Home Reset ACL Mode Disabled M Apply 0 ACL Mode ACL Mode can help to deny or allow certain Client to access the network Select Disable Deny MAC i
36. onfigure wired VID Enter your desire VLAN ID and press Apply to configure the changes Management VLAN Settings Auction After press Apply you must configure your Layer2 Switch or RADIUS Server with the same VLAN ID Otherwise you cannot access to the device s web base configuration page 7 For 802 1x authentication you may construct your network as below diagram SSIDI 2 SSID2 VID 200 EnGenius Device Switch VID 1000 RADIUS Server Note EnGenius product supports maximum 4 different SSID with different VLAN ID 67 Appendix A FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interferenc
37. orted VLAN identifier Radius accounting identifier Profile isolation for infrastructure network VLAN Specify a VLAN number for each SSID to separate the services among clients QoS Use this feature to limit the incoming or outgoing throughput Wi Fi Protect Access Wi Fi Protect Access is a standard based interoperable security enhancement that increases the level of data protection and access control for existing and future wireless LAN system It is compatible with IEEE 802 111 standard WPA leverages TKIP and 802 1X for authenticated key management 1 3 Package Contents Open the package carefully and make sure that none of the items listed below are missing Do not discard the packing materials in case of return the unit must be shipped in its original package 1 Wireless Outdoor Access Point Client Bridge EOC5611P 1 24V 1A Power Adapter 1 Ethernet Cable 1 QIG 1 CD User Manual 2 5gBi 5GHz Dipole Antennas Y Y Y Y Y YV Auction Using other Power Adapter than the one included with EOC5611P may cause damage of the device 1 4 System Requirement The following conditions are the minimum system requirement gt Acomputer with an Ethernet interface and operating under Windows XP Vista 7 or Linux gt Internet Browser that supports HTTP and JavaScript 1 5 Hardware Overview Hardware Specification MCU RF Atheros AR2313 AR5112 Memory 32MB SDRAM Flash 8MB
38. ps 48 5 Scan Sp Security VD EnGenius Open SystomiNo Encryption 2 SystemiNo Encryption 3 EnGenius Open SystemiNo Encryption 4 Wireless Mode EOC5611P supports 802 11a b g wireless band Channel Frequency The channel availability is based on the country s regulation Auto Place a Check to enable Auto channel selection AP Detection AP Detection can help to select a best channel by scan nearby area Current Profile Configure up to four different SSIDs it can help to divide group of clients to access the network Press Edit to configure the profile and place a Check to enable extra SSID Profile Isolation Restricted Client to communicate with different VID by Selecting the Radio button 14 Auction When you select 802 11a 5GHz as your wireless mode only the wireless client which supports 5GHz network can associate with Please make sure your wireless client supports 5GHz wireless network Note Enable Profile Isolation will cause wireless clients cannot communicate each other For more details please refer to the VLAN Management Configuration Guide SSID Profile Wireless Setting SSID Specify the SSID for current profile VLAN ID Specify the VLAN tag for current profile Suppressed SSID Place a Check to hide the SSID Client will not be able to see the broadcast SSID in Site Survey Station Separation Select
39. r debugging purposes Log Home Reset Syslog EXE Fu Local log ILLE Syslog Select Enable or Disable Syslog function from the drop down list Log Server IP Address Specify the Log Server IP address Local Log Select Enable or Disable Local Log service Apply Cancel Press Apply to apply the changes or Cancel to return previous settings 58 8 8 Management gt Diagnostics Click on the Diagnostics link under the Management menu This function allows you to detect connection quality and trace the routing table to the target Traceroute can help you to manage your network by detecting any routing during the transmission If any routers refuse to reply ICMP packet the result will show sign for its Domain Name or IP Address Diagnostics Ping Test Parameters 3 Start Traceroute Target IP Specify the IP address you would like to search Ping Packet Size Specify the packet size of each ping Number of Pings Specify how many times of ping Start Ping Press Start Ping to begin Traceroute Target Specify an IP address or Domain name you would like to trace Start Traceroute Press Start Traceroute to begin 59 9 Network Configuration Example This chapter describes the role of the EOC5611P with 4 different modes The Access Point mode s default configuration is a central unit of the wireless network or as a root device of the wired
40. rver 192 168 1 1 at requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection w Remember my credentials 3 After connected to the EOC5611P successfully browser will pop out a Windows Security window Please enter the correct Username and Password 4 The default Username and Password are both admin Auction If you have changed the Username and Password please enter your own Username and Password 12 4 Wireless Settings 4 1 Switching Operation Mode System System Properties The EOC5611P supports 4 different operation modes Access Point Client Bridge WDS Bridge and Client Router Click System Properties under System Section to begin System Properties EOCS611P Please Select a Country Code Apply Device Name Specify a name for the device but it is not the broadcast SSID It will be shown in SNMP management Country Region Select a Country Region to conform local regulation Operation Mode Select an operation mode via Radio Button Click Apply to save the changes Note If you would like to use Access Point with WDS Function mode please select Access Point 13 Mode and then enable WDS Link Settings function 4 2 Wireless Settings 4 2 1 Access Point Mode Wireless Network Wireless Network Home 802 11a GGHzo4Mb
41. s Server Specify Radius Server IP Address Radius Port Specify Radius Port number the default port is 1812 Radius Secret Specify Radius Secret that is given by the Radius Server Group Key Update Specify Group Key Update Interval time Interval Group Key Update Specify Group Key Update Timeout time Timeout Pairwise Key Update Specify Pairwise Key Update Timeout time Interval Radius Accounting Select Enable or Disable Radius Accounting The detail of Radius Accounting is at next section Auction WPA Mixed means it allow both WPA and WPA2 security types to establish wireless connection 25 4 3 8 Radius Accounting Radius Accounting function allows you to record the statics of user login Your Radius Server must have the ability to support Radius Accounting function LU TN GN wass O C Ku Radius Accounting Select Enable to begin configuration of Radius Accounting Radius Accounting Server sSpecify Radius Accounting Server IP Radius Accounting Port Specify Radius Accounting Server IP The default port is 1813 Radius Accounting Secret Specify Radius Accounting Server Secret that is given by the Radius Accounting Server Radius Accounting Specify Radius Accounting Interval for updating information Interval 4 4 Wireless Wireless Advanced Settings Wireless Advanced Settings Home Data
42. sions to Ethernet networks Network managers in dynamic environments can minimize the overhead caused by moves extensions to networks and other changes with wireless LANs f Wired LAN backup Network managers implement wireless LANs to provide backup for mission critical applications running on wired networks g Training Educational facilities Training sites at corporations and students at universities use wireless connectivity to ease access to information information exchanges and learning Advantage High Output Power up to 26 dBm IEEE 802 11a b g Compliant Detachable antenna support N Type 4 1 Multi Function Point to point Point to multipoint Wireless Connectivity Channel Bandwidth Selection Support RSSI Indicator CB mode Power over Ethernet Support Multi SSID function 4 SSID in AP mode WPA2 WPA WEP IEEE 802 1x support MAC address filtering in AP mode function support AP Router CR mode SNMP Remote Configuration Management QoS support Extended excellent Range and Coverage Fully Interoperable with IEEE 802 11a b g compliant devices Collocate with any antenna for user s environment Users can use different mode in various environment Let users transfer data between two buildings or multiple buildings Using different bandwidth to reach varied distance Users can select the best signal to connect with AP easily Flexible Access Point locations an
43. ss the web interface Apply Cancel Press Apply to apply the changes or Cancel to return previous settings 52 8 2 Management gt Management VLAN Click on the Management VLAN link under the Management menu This option allows you to assign a VLAN ID to the packets on wired network Management VLAN Wired is used to manage your device if the computer has authorized VLAN ID If you would like to use Management VLAN function you must enable Profile Isolation at Wireless Network section Management VLAN Settings EL 60 Management VLAN ID If your network includes VLANs and if tagged packets need to pass through the Access Point specify the VLAN ID into this field If not select the No VLAN tag radio button Apply Cancel Press Apply to apply the changes or Cancel to return previous settings Auction If you reconfigure the Management VLAN ID you may lose connection to the 5611 Verify DHCP server can support the reconfigured VLAN ID and then re connect to the new IP address 8 3 Management SNMP Settings Click on the SNMP Settings link under the Management menu This is a networking management protocol used to monitor network attached devices SNMP allows messages called protocol data units to be sent to various parts of a network Upon receiving these messages SNMP compatible devices called agents return data stored in their Management Information Bases SNMP Settings 77
44. ssaecaaeceneeeseereees 26 4 5 WIRELESS WIRELESS MAC FILTER l S PR e i Pepe onte ee eae t es arte Eee aR Ses 28 4 6 WIRELESS WDS LINK SETTINGS ccessscceessececessseeecesseeeecsscceccessaeeecessaeeecssceeceesaeeecesaaeeecsaeeceesaeeecseaaeeecsaeeeeesaeeeessaae 29 EHE ctt Dm 30 5 SYSTEM ciii edo rn a AQ E E A ec rer E e E Pv eye edere 30 5 2 SYSTEM SPANNING TREE SETTINGS ehe neneeene nennen nenne hn ense sene eset tese e sse e sense sees seti 31 6 ROUTER SETTINGS EZ C se 32 6 1 ROUTER WAN SETTINGS ccccccccesesescecececeeueseececececeeusneecceceauuseececececeaueneececececsauseaeneecesessaueuseesesscuaueneeeeeessauaaereeeeeeeees 32 6 1 1 WAN Settings Static sesenta esee atate ease eset eaae sees e nasse eset seta 32 6 1 2 WAN Settings DHCP Dynamic lP 35 6 1 3 WAN Settings PPPoE Point to Point Protocol over Ethernet eene 37 6 1 4 WAN Settings PPTP Point to Point Tunneling Protocol enne 39 6 2 ROUTER gt LAN SETTINGS ic I tee ve ee re e E ee Vei ee ee e t ve de 41 6 3 ROUTER VPN PASS THROUGH an h ua ishu ash esee baee ede e vb ae pe aeu 42 6 4 ROUTER
45. st of Clients that are associated to the EOC5611P The MAC addresses and signal strength for each client is displayed Click on the Refresh button to refresh the client list Client List _ Home Reset 46 7 3 Status gt System Log Click on the System Log link under the Status drop down menu The device automatically logs records events of possible interest in its internal memory If there is not enough internal memory for all events logs of older events are deleted but logs of the latest events are retained System Log uL A Local Log 1s disabled 1 Refresh 47 7 4 Status gt WDS Link Status The WDS Link Status will only show in WDS Bridge Mode Click on the WDS Link Status link under the Status drop down menu This page displays the current status of WDS link including station ID MAC address status and RSSI WDS Link Status Home Reset 48 7 5 Status Connection Status Click on the Connection Status link under the Status drop down menu This page displays the current status of the network including network type SSID BSSID connection status wireless mode current channel security data rate noise level and signal strength 7 6 Status gt DHCP Client Table Click on the DHCP Client List link under the Status drop down menu This page displays the list of Clients that are associated to the EOC5611P through DHCP The MAC addresses and signal strength for
46. tworks File and Printer Sharing for Microsoft Networks E QoS Packet Scheduler Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity Cancel Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise vou need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 166 t Subnet mask 255 255 255 0 Default gateway Use the following DNS server addresses Preferred DNS server Alternate DNS server Auction IP Address entered in the TCP IP Properties needs to be at the same subnet of the 5611 IP Address For example EOC5611P s default IP Address is 192 168 1 1 so the IP Address in the TCP IP settings could be 192 168 1 10 3 2 Logging Method After complete the IP settings from last section you can now access the web based configuration menu 1 Open web browser 2 Enter IP 192 168 1 1 into you address filter Auction If you have changed the EOC5611P LAN IP address make sure you enter the correct IP Address Windows Security The se
Download Pdf Manuals
Related Search