SYBA PCI Express to SATA II Controller Card
Contents
1. Select CDROM drive 2 Select folder Silicon_Image 3a BIOS with RAID function select folder SZL31I4RAID or 3b BIOS without RAID function select folder SIL3114 4 Select folder Win_Drv The Update Device Driver Wizard will appear informing you that it has found la BIOS with RAID function Silicon Image SIL3114 SATARaid Controller driver 1b BIOS without RAID function Silicon Image SIL3114 SATA Link Controller driver 2 Click OK button and then the Next button If the Digital Signature Not Found dialog appears click Yes to continue installing the driver Follow the instructions to finish up the driver installation Finally switch off your system Connect the SATA hard disk from the mainboard s SATA controller to the Serial ATA host controller card and start Windows 2000 XP Installing RAID Management Software This software is use to monitor and manage the RAID set under Windows environment To install this RAID Management software please follow these steps Step 1 Start Windows Step 2 Click Start and then Run Step 3 Insert the Driver CD into the CDROM drive and select Browse button Select CDROM drive Select folder Silicon_Image Select folder SIL3114RAID Select folder Utility Select JAVA_RUNTIME_ENVIRO EXE Click the Open button and then the OK button Step 4 Follo2. 4 SATA Raid Controller driver or 1b BIOS without RAID function Silicon Image SIL 3114 SATALink Controller driver 2 Click the Next button Step 7 Follow the instructions to finish up the driver installation Windows NT 4 0 and Windows 2000 XP Fresh Installation If you are performing a new Windows NT 4 0 2000 or XP installation to a SATA hard drive attached to the Serial ATA host controller card Step 1 Make sure to copy the Windows driver from the Driver CD on to a 1 44MB floppy diskette You will need the driver in the 1 44MB floppy diskette during the installation 2 Step 2 Step 3 Step 4 Step 5 Step 6 a BIOS with RAID function Copy the Silicon_Image SIL3114RAID Win_Drv driver from the Driver CD to the diskette b BIOS without RAID function Copy the Silicon_Image SIL3114 Win_drv driver from the Driver CD to the diskette Make sure the SATA hard drive is properly connected to the Serial ATA host controller card and the card is properly installed into a PCI slot If your Windows NT 2000 XP Installation CD is bootable simply put the CD into the CDROM drive and startup your system to begin installation If your Windows NT 2000 XP Installation CD is not bootable you must use the Windows NT 2000 XP bootable diskette to boot up first before commencing installation Press F6 for third party SCSI or driver installation at the beginning of the text mode installation Insert the 1 44MB flo
3. E Controller Revision 1 0 e Supports four independent Serial ATA channel e Independent 256 byte FIFOs per Serial ATA channel for host reads and writes RAID Functions Optional e Supports RAID functions 0 1 or 0 1 e Supports co exist RAID set and Non RAID HDD e Allow HDDs with different sizes to be configured in a RAID set Accessories e One User Manual e One Serial ATA host controller card e Two Serial ATA cables e One Driver CD How to install the Serial ATA host controller card into your computer Turn off your computer and all external devices connect to it Disconnect your computer from the power sources Open the computer case Refer to your computer user manual for more details Find an available PCI slot and remove the slot bracket Save the bracket screw for later use SER ee Align the Serial ATA host controller card horizontally with respect to the PCI slot and insert it into the slot firmly and evenly Take care not to force it into the slot Once you have properly positioned the Serial ATA host controller card into the slot fasten it to the computer case with the bracket screw you have saved 6 Connect the HDD LED connector from the computer case to the HDD Busy LED connector JP4 on the Serial ATA host controller card 7 Connect any Serial ATA device to the connector s of the Serial ATA host controller card with the provided Serial ATA cable 8 Close the computer case Make sure to reconnect all the extern
4. MANL SIL3114 EN 240604 SERIAL ATA HOST CONTROLLER CARD USER MANUAL SA3114 4l SA3114 4IR SA3114 2E2l SA3114 2E2IR WARNING Before installing and activating RAID function please make sure you have a complete backup of your existing data from hard drives Manufacturer is not responsible for data loss due to abuse misuse or neglect Should you have any installation problem please contact your dealer for assistance All contents and specification mentioned in this manual are subject to change without prior notice All brand names and trademarks referenced and mentioned in this manual are property of their respective owners Features This Serial ATA host controller card is designed to offer a high performance cost effective and reliability solution to user who needs to accommodate storage peripherals with the new Serial ATA interface It can control four independent Serial ATA channel each channel has its own Serial ATA bus and will support one Serial ATA device This card supports the Serial ATA Generation 1 transfer rate of 1 5Gb s ISOMB s Specifications e Silicon Image SIL3114 Serial ATA SATA host controller chipset e Compliant with Serial ATA Specification Revision 1 0 e Supports Serial ATA Generation 1 transfer rate of 1 5Gb s ISOMB s e Compliant with PCI Specification Revision 2 2 e Compliant with PCI IDE Controller Specification Revision 1 0 e Compliant with Programming Interface for Bus Master ID
5. _Drv 1a BIOS with RAID function Select Silicon Image SIL3114 SATARaid Controller 1b BIOS without RAID function Select Silicon Image SIL3114 SATALink Controller 3 Step 7 Step 8 2 Click OK to continue Click Yes to restart your computer to complete driver installation Finally switch off your system Connect the SATA hard disk from the mainboard s SATA controller to the Serial ATA host controller card and start Windows NT Installing drivers to an existing SATA hard drive with Windows 2000 XP If you are already using a SATA hard drive with Windows N T in your system and you want to connect this SATA hard drive to the Serial ATA host controller card as the default bootable drive you must follow these procedures Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Make sure the SATA hard drive is still connected to the default SATA controller Make sure the Serial ATA host controller card is properly installed into your system and there is no SATA device connected to the card Start Windows 2000 XP Windows 2000 XP will inform you that it has found a PCI RAID Controller Click the Next button to continue Select Search for a suitable driver for your device Recommended and click on the Next button Insert Driver CD into the CDROM drive Select Specify a location and click the Next button to continue 1
6. al devices to your computer 1 Driver Installation Note Current drivers can only support Windows 98 98SE ME NT 2000 and XP Driver Locations This Serial ATA host controller card has two sets of drivers a SIL3114RAID Serial ATA host controller card BIOS with RAID function b SIL3114 Serial ATA host controller card BIOS without RAID function These two sets of drivers can be located in these two directories respectively of the Driver CD 1 SIL3114RAID Silicon_Image SIL3114RAID 2 SIL3114 Silicon_Image SIL3114 Windows 98 98SE or Windows ME Step 1 Start Windows 98 98SE or Windows ME Step 2 The Update Device Driver Wizard will appear informing you that it has found a PCI RAID Controller click the Next button Step 3 a Windows 98 98SE user Select Specify a location b Windows ME user Select Specify the location of the driver Advanced and then select Specify a location Step 4 Insert the Driver CD in the CDROM drive and click on the Browse button Step 5 At the Browse option 1 Select CDROM drive 2 Select folder Silicon_Image 3a BIOS with RAID function Select folder SIL31I4RAID or 3b BIOS without RAID function Select folder SILI LHP 4 Select folder Win_Drv Step 6 The Update Device Driver Wizard will appear informing you that it has found la BIOS with RAID function Silicon Image SIL 311
7. ppy diskette into the floppy drive Press s when setup asks if you want to specify an additional device a BIOS with RAID function Select Silicon Image SIL3114 SATARaid Controller b BIOS without RAID function Select Silicon Image SIL3114 SATALink Controller Press Enter to continue on with text mode setup Follow the setup instructions to complete installing Windows NT 2000 XP Installing drivers to an existing SATA hard drive with Windows NT 4 0 If you are already using a SATA hard drive with Windows N T in your system and you want to connect this SATA hard drive to the Serial ATA host controller card as the default bootable drive you must follow these procedures Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Make sure the SATA hard drive is still connected to the default SATA controller Make sure the Serial ATA host controller card is properly installed into your system and there is no SATA device connected to the card Start Windows NT After Windows NT boot up open Control Panel and then enter SCSI Adapters Insert the Driver CD into the CDROM drive and select Drivers tab and click Add Select Have Disk and click on Browse button 1 Select CDROM drive 2 Select folder Silicon_Image 3a BIOS with RAID function Select folder SIL31I4RAID or 3b BIOS without RAID function Select folder SIL3114 4 Select folder Win
8. w the instructions to complete installation Step 5 Once you have installed the JAVA_RUNTIME_ENVIRO program you need to install the RAID Management software Select CDROM drive Select folder Silicon_Image Select folder SJL3114RAID Select folder Utility Select JAVA_SATA RAID EXE Click the Open button and then the OK button Step 6 Follow the instructions to complete installation Step 7 For more information on the RAID Management software please refer to the SATARAID User s Manual located in the Silicon_Image SIL3 114RAID UTILITY directory BIOS Setup If you already have a bootable hard disk connected to the mainboard s IDE controller and you want to use the SATA hard disk connected to the Serial ATA host controller card as default bootable drive Drive C you need to set the mainboard s BIOS to boot SCSI first Please refer to the mainboard s user manual for more details
Download Pdf Manuals
Related Search