Chief RMT2, Low-Profile Tilt Mount (26-42" Displays)
Contents
1. Figure 9 1 Make sure interface brackets are in the kickstand position by pulling down on handles as far as possible See Figure 10 2 Hang display with brackets B and C on upper rail of wall plate A Kickstand should be engaged with lower portion of wall plate See Figure 10 views from left side kickstand engaged kickstand against wall Figure 10 NOTE Any cable management or rear display adjustments should be made when the display is resting on the kickstand 3 Unlock kickstand by pushing up on interface brackets until kickstand rests against the wall See Figure 10 4 Push on the interface brackets further in order to lock display into position against wall See Figure 10 5 Straps can be tucked behind display on notch on interface brackets B and C after installation is complete so that they will not be visable to the viewer See Figure 9 6 Optional Route padlock or cable lock not included through bottom holes on interface bracket to provide additional security See Figure 10 RMT2 RLT2 RXT2 Installation Instructions Switching Interface Brackets Optional For wide hole patterns interface brackets must be reversed See Table below to determine if this is necessary Table 1 Hole Pattern Width Model normal installation swap uprights RMT2 100 440mm 441 506mm RLT2 100 663 664 728 8 RXT2 200 847m2. Dy a 1 19 68 I A I 3 5 2 50 1900 ENTERUNE L TO BOTIOM OF 38 00 WALL PLATE OPENING CABLE ACCESS WHEN KICKSTAND IS ACTIVATED TLTS BACK 5 RMT2 RLT2 RXT2 Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Marcar con l piz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche
3. Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option 2 d y 4 9 9 Hex Head Wrench Llave de cabeza hexagonal 9 Q Sechskantschllssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit RMT2 RLT2 RXT2 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 7 32 5 5mm 5 16 7 9mm 1 2 12 7mm 21 12542 2 Ss by Dy C 1 ight upright Y ivali piatej right upright left upright RXT2 shown For below kit quantities are 4 for RMT2 and RLT2 6 for RXT2 G 1 Hardware Bag GA 8 GE 6 GI 6 GL 6 M4x16mm 5 6 xi6mm 8 x 20mm D 4 or 6 GP 8 5 16 x 2 1 2 1 4 6 4mm GB 6 GF 6 GM 6 20mm M5 x20mm Z nn E 4 or 6 D I 1 4 6 4mm 1 2 12 7mm GG 6 GK 6 5 GC 6 6 GN 6 4 25 M5x25mm M6x35mm 4
4. 54 4 or 6 GD 6 GH 6 _ GS concrete anchor M4x35mm M4 x 35mm washer RMT2 RLT2 RXT2 Installation Instructions Assembly And Installation Install Wall Plate to Wall Wood Studs WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm 1 Unfold wall plate A to prepare it for mounting to wall See Figure 1 Figure 1 2 Level wall plate A and mark locations of pilot holes See Figure 2 NOTE The RMT2 must be installed on two 16 studs The RLT2 can be installed on 16 studs inner holes or 24 studs outer holes For the RXT2 it can be mounted over two or three 16 studs or two 24 studs If mounting to three 16 studs it must be mounted to all three studs using the outer holes and center holes See Figure 3 NOTE The vertical center of the wall plate is labeled as the center directly below each hinge Keep this in mind when determining mounting location See Figure 3 3 Drill 7 32 5 5mm diameter pilot holes into wood studs at marked l
5. INSTALLATION INSTRUCTIONS Universal Tilt Mounts RMT2 RLT2 RXT2 i CHIEF Our Mounts Your Vision RMT2 RLT2 RXT2 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equip
6. TE For the RLT2 either the inner or outer four holes may be used NOTE For the RXT2 use the outer four holes and the two middle holes on wall plate for installation NOTE The vertical center of the display will be even with the center line indicated on the labels located directly below each hinge Keep this in mind when determining mounting location See Figure 5 CENTER Figure 5 3 Drill 5 16 7 9mm diameter pilot holes into wall at marked locations Holes must be drilled at least 2 1 2 inches deep See Figure 5 4 Install four or six concrete anchors F into drilled holes Use a hammer to tap anchors into holes See Figure 6 Figure 6 5 Using 1 2 12 7mm wrench install screws D through flat washers E wall plate A and into concrete anchors See Figure 7 E RMT2 RLT2 RXT2 Installation Instructions Install Brackets to Display WARNING The minimum hole pattern size is 100mm x 100mm for the RMT2 and RLT2 and 200mm x 200mm for the RXT2 1 Lay display face down on protective surface CAUTION Using screws of improper diameter may damage your display Proper screws will easily thread into display mounting holes 2 Select screw diameter by examining hardware GA GO 8mm 6mm 5mm or 4mm and comparing with mounting holes on display See Figure 8 3 Select spacers See Figure 8 e If mounting holes are not recessed and both b
7. for details 7 Using Phillips screwdriver carefully install selected screws through universal washers GS brackets B and C and spacers GP or GQ if required into display See Figure 8 8 Tighten all screws Ensure all applicable display mounting holes 4 6 or 8 are used GA GO x4 x6 x8 GS x4 x6 x8 GA GO x4 x6 x8 00 GS 4 6 8 UC 5 lt Figure 8 Installation Instructions RMT2 RLT2 RXT2 Install Display to Wall Plate WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs 56 7 kg for the RMT2 RLT2 or 175 Ibs 79 4 kg for the RXT2 Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury WARNING Display may be very heavy Ensure display can be safely lifted and maneuvered as required to install on wall plate Failure to take adequate precautions can result in serious personal injury or damage to equipment WARNING Interface brackets must be hung on opposite sides of the center tab on wall plate See Figure 9 A interface brackets must be hung on opposite sides of center tab center tab
8. m 848 913mm 1 Remove the tilt tension knob washer and screw from interface bracket See Figure 11 IMPORTANT Hold the brackets steady when removing the knob washer and screw from interface bracket to prevent internal washers from falling out If internal washers do fall out they must be reinserted in proper position before reinstalling knob on the other side 2 Replace the knob washer and screw in the opposite order See Figure 11 Figure 11 3 Repeat for the other interface bracket 4 Install interface brackets according to instructions in Install Brackets to Display section 10 Tilt Adjustment 1 Adjust tilt tension adjustment knobs to desired tension See Figure 12 2 Adjust tilt of display by pulling the top of display away from the wall until desired tilt position is reached See Figure 12 3 Tighten tilt tension adjustment knobs to secure tilt position See Figure 12 0 9 De tilt tension adjustment knob Figure 12 Installation Instructions RMT2 RLT2 RXT2 11 RMT2 RLT2 RXT2 Installation Instructions USA International Our Mounts Your Vision Europe Chief Manufacturing a products divi sion of Milestone AV Technologies Asia Pacific 8800 002040 01 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 10 10 gt 8401 Eagle Creek Pa
9. ment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installers responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached does not exceed 125 Ibs 56 7 kg for the RMT2 RLT2 175 Ibs 79 4 kg for the RXT2 Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury aa 16 00 19 94 100 7 87 222 TOP MOUNTING 34 HOLE CENTERLINE 12 NOTCH ON WALL PLATE 1 El dE El e 0 1 i 8 1
10. ocations See Figure 2 Figure 2 2x24 Figure 3 4 Install 5 16 x 2 1 2 hex head cap screws through four flat washers E wall plate A and into wood studs See Figure 4 Figure 4 Installation Instructions RMT2 RLT2 RXT2 Install Wall Plate to Wall Concrete Concrete Block or Brick WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners WARNING EXPLOSION AND FIRE HAZARD CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of gas water waste or any other plumbing before cutting drilling or installing fasteners 1 Unfold wall plate A to prepare it for mounting to wall See Figure 1 2 Level wall plate A and mark locations of pilot holes at desired mounting location See Figure 5 NO
11. rackets B or C can lay flat against display then no spacers are required e If mounting holes are recessed or if protrusions prevent brackets B or C from laying flat then spacers GP or GQ must be used Select shortest spacer which will provide adequate fill All spacers must be same length CAUTION Using screws of improper length may damage your display Proper screws will have adequate thread engagement without contacting bottom of display mounting holes 4 Select screw length See Figure 8 e Using your hand insert SHORTEST length screw of selected diameter GA GE GI or GL through bracket B or C universal washer GS selected spacer GP or GQ if required into display mounting hole Do NOT thread screw into hole at this time e Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter If screw length is inadequate select longer screw Select shortest screw which will protrude the required distance 5 Place brackets and display ensuring See Figure 8 Upper hooks are towards top of display e Center of brackets and are as close to the center of the back of display as possible after being installed Center of bracket is indicated by the diamond shaped hole 6 If installing display with wide hole pattern it may be necessary to swap the uprights B and C See Switching Interface Brackets section
12. rkway Savage 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH d
13. z i 5 19 7 00 1 tt WALL 8 38 16 50 dess OPENING iiaa 1120 15 75 i 5 i 8 Ei 2 50 1 4 5 9 CENTERLINE TO BOTIOM OF WALL PLATE OPENING 11 00 CABLE ACCESS WHEN KIC KSTAND ISACTIVATED La 22 00 TILTSBAC R 5 45 Installation Instructions RMT2 RLT2 RXT2 ie SS i La 24 00 d 16 00 7 00 WALL 1 104 2869 OPENING i 7 87 34 TOPMOUNTNG 196 4 12 v HOLE TO CENTERLINE MAX TILT j NOTCH ON WALL PLATE 5 EI 5 de ES Eli ES El 5 1 j m 5 10 8 38 We 16 50 E Gs 11 49 15 75 bi SS i XY qi 2 1 8 11 2 50 T CENTERLINE L BOTIOM OF WALL PLATE OPENING 15 38 CABLE ACCESS 30 75 WHEN KIC KSTAND IS ACTIVATED TITS BACK 5 La 32 00 La 24 00 4 1600 35 94 1 00 12 Me Lab Ze WAL MAX ONNE HOLE TO CENTERLINE EE MAX TILT NOTCH ON WALL PLATE l l I als SS 1 de 1 d 519 tet P ry I 8 38 1149
Download Pdf Manuals
Related Search