Avanti WD361 water dispencer
Contents
1. The water dispenser is pre cleaned at the factory but the reservoir and water lines must be flushed with fresh water before use as follows Keep the unit unplugged Fill water tank with tap water full to capacity more than 3 4 of a gallon Wait for 5 minutes until water settles Press the hot water faucet until water comes out then stop Plug the dispenser into the electrical outlet Both heating and cooling indicator lights on front will light up at first We are ready to complete the first cycle In order to do that wait for the hot water indicator light to go off first approximately 10 minutes then wait for the cold water indicator light to go off another 40 minutes approximately Unplug the dispenser from the electrical outlet Proceed to drain the water from the faucets one at a time until no more water remains Note To facilitate this operation use a large container Then drain any water left in the tanks by opening the drain plug located on the back until it drains completely Proceed to close the drain cap Place the 5 gallon bottle of water on the water intake allow water to stand for approximately one minute Open water faucets to insure water flows from both faucets Plug dispenser into the electrical outlet Now you are ready to use your water dispenser Your water dispenser has been cleaned and sanitized before leaving the factory but in case a taste problem develops place two tablespoons of baking soda2. O IT INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Model Number Numero de Modelo WD361 CAUTION BEFORE USE PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice La secci n en espa ol empieza en la p gina B Avanti Products P O Box 520604 Miami Florida 33152 www avantiproducts com Registration Information Thank you for purchasing this fine Avanti product Please fill out this card and return it within 100 days of purchase and receive these important benefits x Protect your product We will keep the model number and date of purchase of your new Avanti product on file to help you refer to this information in the event of an insurance claim such as fire or theft x Promote better products We value your input Your responses will help us develop products designed to best meet your future needs E E detach here Avanti Registration Card Name Model Serial Address Date Purchased Store Dealer Name City State Zip Occupation As Your Primary Residence Do You Area Code Phone Number Own Rent Did You Purchase An Additional Warranty Your Age Extended Food Loss None under 18 18 25 26 30 Reason For Choosing This Avanti Product 31 35 36 50 over 50
3. Please indicate the most important factors Marital Status that influenced your decision to purchase Married Single this product Is This Product Used In The Price Home Business Product Features How Did You Learn About This Product Avanti Reputation Advertising Product Features Product Quality n Store Demo Personal Demo Salesperson Recommendation Other Friend Relative Recommendation Comments Warranty Other HELP US HELP YOU Read this guide carefully It is intended to help you operate and maintain your new water dispenser properly Keep it handy to ans wer your questions If you don t understand something or you need more help please call Avanti Customer Service 800 220 5570 Keep proof of original purchase date such as your sales slip with this guide to establish the warranty period Write down the model and serial numbers You ll find them on a label located on the back side of the unit Please write these numbers here Date of Purchase Model Number Serial Number Use these numbers in any correspondence or service calls concerning your water dispenser If you received a damaged water dispenser immediately contact the dealer or builder that sold you the water dispenser Save time and money Before you call for service check the Problem Solver Guide It lists causes of minor operating problems that you can correct yourself IF YOU NEED SERVICE We
4. A USAR EL ENFRIADOR POR UN TIEMPO PROLONGADO DESENCHUFE LA UNIDAD QUITE EL BOTELLON DE AGUA COLOQUE LOS INTERRUPTORES MARCADOS CALIENTE Y FRIO EN LA PARTE TRASERA EN LA POSICION OFF DRENE EL AGUA ABRIENDO LAS LLAVES DRENE LA APERTURA EN LA PARTE TRASERA QUITANDO EL TAPON EL ENFRIADOR DEBE TRANSPORTARSE PARADO Y CUBIERTO CON UNA FRAZADA PARA EVITAR QUE SE RAYE CENTRO DE SERVICIOS LA MAYORIA DE LOS PROBLEMAS SE RESUELVEN CON UNA SIMPLE LLAMADA TELEFONICA A NUESTRO NUMERO SIN CARGO 1 800 220 5570 ANTES DE DEVOLVER EL PRODUCTO O PARA OBTENER LA DIRECCION Y NUMERO DE TELEFONO DEL CENTRO DE SERVICIO MAS CERCANO LLAME AL SIGUIENTE NUMERO 1 800 220 5570 16 POSIBLES PROBLEMAS CAUSA DERRAME DE AGUA POR FUERA DEL LA BOTELLA ESTA PERFORADA EL AGUA NO ESTA SUFICIENTEMENTE FRIA SU TEMPERATURA DEBERIA SER DE 5 A 7 C CON UNA TEMPERATURA AMBIENTE DE 20 C SI NO ES ASI LLAME AL CENTRO DE SERVICIO EL TERMOSTATO PODRIA ESTAR DEFECTUOSO EL AGUA NO ESTA SUFICIENTE CALIENTE SU TEMPERATURA DEBERIA SER DE 80 A 90 C CON UNA TEMPERATURA AMBIENTE DE 20 C SI NO ES ASI LLAME AL CENTRO DE SERVICIO EL TERMOSTATO PODRIA ESTAR DEFECTUOSO EL ENFRIADOR NO ENFRIA O CALIENTA EL VERIFIQUE LOS CIRCUITOS FUSIBLES O AGUA DISYUNTORES PRINTED IN CHINA 17
5. re proud of our service and want you to be pleased If for some eason you are not happy with the service you receive here are some steps to follow for further help FIRST contact the people who serviced your appliance Explain why you are not pleased In most cases this will solve the problem NEXT if you are still not pleased write all the details including your telephone number and send to Customer Service Avanti Products 10880 NW 30 Street Miami FL 33172 PARTS AND FEATURES UL UL AITAITA ATAT 06 U U ALA AU IAAL HIHI i ann ALU LLL Utd li id A Important Safety Instructions WARNINGS Read all instructions before using the water dispenser Never clean parts with flammable fluids The fumes can create a fire hazard or explosion Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other water dispenser The fumes can create a fire hazard or explosion Do not plug unit into receptacle until you ensure the water tank switches are off Save these instructions INSTALLATION GUIDELINES Remove the exterior and interior packing Place your appliance on a floor that is strong enough to support the dispenser when it is fully loaded If it does not sit level on the floor adjust the front right foot to level the unit well to the floor Note Only the front right foot is adjustable Locate the appliance away from dir
6. NECTE LA UNIDAD DE LA PARED EMPIEZE A DRENAR LAS LLAVES UNA A LA VEZ HASTA QUE SALGA EL ULTIMO CHORRO DE AGUA EN LA PARTE TRASERA DE LA UNIDAD ENCONTRARA UNA TAPA PLASTICA GIRE HACIA LA IZQUIERDA LA TAPA HASTA QUE SALGA EL ULTIMO CHORRO CUANDO NO SALGA MAS AGUA DE LA APERTURA CIERRE LA TAPA PLASTICA TOME EL BOTELLON DE AGUA Y SIGA LAS INSTRUCCIONES PARA CAMBIAR EL 15 x BOTELLON ENCHUFE LA UNIDAD AHORA SU ENFRIADOR ESTA LISTO PARA SU USO CONTROLES DE OPERACION N CONTROL DE AGUA FRIA ABRA LA LLAVE DE AGUA FRIA 10 EL INDICADOR DE LUZ VERDE SE ENCENDERA Y EL PROCESO DE ENFRIAMIENTO COMENZARA CUANDO LA TEMPERATURA ALCANCE APROXIMADAMENTE 5 7 lt LA LUZ VERDE SE APAGARA AUTOMATICAMENTE CONTROL DE AGUA CALIENTE ABRA LA LLAVE DE AGUA CALIENTE 11 EL INDICADOR DE LUZ ROJA SE ENCENDERA Y EL PROCESO DE CALENTAMIENTO DEL AGUA COMENZARA CUANDO LA TEMPERATURA ALCANCE APROXIMADAMENTE 80 C LA LUZ ROJA SE APAGARA AUTOMATICAMENTE Y OTRO CICLO DE CALENTAMIENTO EMPEZARA MANTENIMIENTO A INTERVALOS REGULARES UNA VEZ AL MES INSPECCIONE EL CONDENSADOR O REJILLA DE ALAMBRE LOCALIZADA EN LA PARTE TRASERA DE LA UNIDAD ANTES DE EFECTUAR LA LIMPIEZA DESENCHUFE EL ENFRIADOR USE UNA ASPIRADORA O UN CEPILLO DURO PARA QUITAR EL POLVO PARA LIMPIAR LAS PARTES DE PLASTICO SE REQUIERE JABON LIQUIDO Y AGUA TIBIA NO USE LIMPIADORES ABRASIVOS EN LA SUPERFICIE SUPERIOR NI EN LA BANDEJA DE ESCURRIMIENTO SI NO VA
7. PRODUCTS CUSTOMER SERVICES Product Information Whatever your questions are about our products 800 323 5029 help is available Part Orders You may order parts and accessories that will be 800 220 5570 delivered directly to your home You may order these items by personal check money order Master Card or Visa In Home Repair Service An Avanti Products authorized service center will 800 220 5570 provide expert repair service scheduled at a time that is convenient for you Our trained servicers know your appliance inside and out 12 YOUR Avanti Products WARRANTY Staple your sales receipt here Proof of original purchase date is needed to obtain WHAT IS COVERED LIMITED ONE YEAR WARRANTY For one year from the date of purchase by the original owner Avanti Products will at its option repair or replace any part of the appliance which proves to be defective in material or workmanship under normal use During this period Avanti Products will provide all parts and labor necessary to correct such defects free of charge so long as the appliance has been installed and operated in accordance with the written instructions in this manual In rental or commercial use the warranty period is 90 days service under warranty LIMITED SECOND THROUGH FIFTH YEAR WARRANTY For the second through the fifth year from date of original purchase Avanti Products will provide a replacement compressor free of charge due to a failure Y
8. S PARA CAMBIAR EL BOTELLON QUITE EL BOTELLON VACIO LIMPIE EL CUELLO DEL BOTELLON NUEVO CON UN TRAPO LIMPIO LEVANTE EL BOTELLON HACIENDO FUERZA CON LAS PIERNAS Y NO LA ESPALDA TOME EL BOTELLON POR LOS LADOS Y DIRIJA EL CUELLO DEL MISMO HACIA LA APERTURA DEL TANQUE z VOLTEE EL BOTELLON COMO SI FUERA A SOLTAR AGUA E INSERTE EL CUELLO DEL BOTELLON EN LA APERTURA DEL TANQUE HASTA QUE SE COLOQUE EN LA POSICION CORRECTA DIRECCIONES BASICAS DE OPERACION z COLOQUE EL ENFRIADOR DE PIE POR UN PERIODO DE 2 HORAS ANTES DE ENCHUFAR LA UNIDAD A LA PARED COLOQUE EL ENFRIADOR EN UN AREA BIEN VENTILADA Y DEJE UN ESPACIO DE UN POCO MAS DE 2 PULGADAS ENTRE LA UNIDAD Y LA PARED z ESCOJA UN LUGAR CON PISO NIVELADO z NO COLOQUE EL ENFRIADOR DONDE LA TEMPERATURA AMBIENTAL PUEDA BAJAR DE 32 F 0 C ANTES DE ENCHUFARLO AUNQUE ENFRIADOR SALE LIMPIO DE LA FABRICA DEBE LIMPIAR Y ESTERILIZAR LOS CONDUCTOS DEL TANQUE Y LOS GRIFOS DE ACUERDO A LOS SIGUIENTES PASOS LLENE EL TANQUE DE AGUA HASTA EL TOPE CON AGUA DE LA PILA s DEJE NIVELAR EL AGUA POR 5 MINUTOS ABRA LA LLAVE DE AGUA CALIENTE HASTA QUE SALGA AGUA Y CIERRELA INMEDIATAMENTE ENCHUFE LA UNIDAD A LA PARED ENCRENDA LOS DOS INTERRUPTORES SITUADOS EN LA PARTE TRASERA LOS DOS INDICADORES DE LUZ SE ALUMBRARAN ESPERE HASTA QUE EL INDICADOR DE AGUA CALIENTE SE APAGUE APROX 10 MINUTOS ENTONCES ESPERE HASTA QUE EL INDICADOR DE AGUA FRIA SE APAGUE APROX 5 MINUTOS DESCO
9. and add tap water Fill water tank again and repeat basic operations previously outlined except turn the switch marked HOT OFF to avoid leaving residues in hot water tank ATTENTION If you do not plan to use the water heating function for more than three days we recommend that you turn the HOT switch to the OFF position WARNING IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL SHOCK IF THE POWER CORD IS DAMAGED HAVE IT REPLACED BY AN AUTHORIZED AVANTI PRODUCTS SERVICE CENTER OPERATING YOUR WATER DISPENSER s Steps to replace water bottles Use a clean cloth to wipe off neck of bottle Remove cap Carefully lift bottle approx 40 Ibs using your legs and not your back Do not place hands on opening of bottle while placing in reservoir Insert the water bottle on the water intake over reservoir opening so it settles properly on it Wipe off any water which may have splashed on dispenser top When a new bottle is installed you must open the hot water faucet and remove no less than 4 full cups of water to insure the water flows properly and the water reservoir is at the proper level Electrical Connection This appliance should be properly grounded for your safety The power cord of this appliance is equipped with a three prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock Plug the appliance into an exclusive
10. e cooler The cup dispenser comes equipped with a mounting bracket and screws and may be ordered by completing the enclosed order form provided with your instruction manual CARE AND MAINTENANCE Wash the inside of the reservoir with a warm water and baking soda solution The solution should be about 2 tablespoons of baking soda to a quart of water The drip tray and water faucets should be cleaned with mild detergent and warm water At regular intervals or once a month inspect the coils located across the back of the dispenser Vacuum accumulation of dust or clean it with a hard brush s TAKING DISPENSER OUT OF SERVICE If the water dispenser will not be used for a long period of time unplug the power cord from the wall outlet Drain the water through the faucets Turn the switch market hot to the OFF position WARNING THE WATER COMING OUT OF THE BACK SIDE MARKED HOT MAY BE SCOLDING s Unit should not be transported on the sides Place it upright if possible and cover it with a blanket Y Y PROBLEMS WITH YOUR WATER DISPENSER You can solve many common water dispenser problems easily saving you the cost of a possible service call Try the suggestions outlined below to see if you can solve the problem before calling the service TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE Water dispenser does not operate Not plugged in The circuit breaker tripped or a blown fuse Water cooler is not cold enou
11. ect sunlight and sources of heat stove heater radiator etc Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption Extreme cold ambient temperatures may also cause the appliance not to perform properly Allow 2 inches of space between the water dispenser and the wall which allows for proper air circulation to cool the compressor Plug the appliance into an exclusive properly installed grounded wall outlet Do not cut or remove the third ground prong from the power cord under any circumstances Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center This water dispenser is not recommended for outdoor use Do not locate the dispenser in area where the temperature may fall below freezing 32 F Keep area around dispenser free of dust and dirt Keep the reserve supply of water bottles away from excessive heat and light Never unplug the water cooler except for maintenance OPERATION INSTRUCTIONS Before Using Your Water Dispenser Check to be sure the following parts are included x Instruction manual x 4extra cup dispenser cabinet plugs x Accessories order form Before connecting the appliance to the power source let it stand upright for approximately 2 hours This will reduce the possibility of a malfunction in the cooling system from handling during transportation NOTE
12. gh Check to be sure the cold switch on the back is ON The water dispenser does not have the correct clearances Check to be sure the hot switch on the back is ON Compressor turns on and off frequently The room temperature is hotter than normal The temperature control is not set correctly The water dispenser does not have the correct clearances Check to assure that the water dispenser is level The water dispenser seems to make too much The rattling noise may come from the flow of the noise refrigerant which is normal As each cycle ends you may hear gurgling sounds caused by the flow of refrigerant in your water dispenser Contraction and expansion of the inside walls may cause popping and crackling noises The water dispenser is not level Bottle feels warm The water system is overfilled Dispense Cold water until air is released into the bottle Water bottle is hot Water is boiling in the hot tank and bubbling up into the bottle Press the hot dispenser button until water flos to remove air from the hot tank SERVICE FOR YOUR WATER DISPENSER We are proud of our customer service organization and the network of professional service technicians that provide service on your Avanti appliances With the purchase of your Avanti appliance you can have the confidence that if you ever need additional information or assistance the Avanti Products Customer Service team will be here for you Just call us toll free AVANTI
13. ou are responsible for the service labor and freight charges In rental or commercial use the limited compressor warranty is one year and nine months Cost to move the appliance to the servicers shop and back to the user s home as may be required are the user s responsibility WHAT IS NOT COVERED Incidental or consequential damages Parts and labor costs for the following will not be considered as warranty Inner door panels door shelves door rails and or door supports Lightbulbs and or plastic housing Plastic cabinet liners Punctured evaporator that voids the warranty on the complete sealed system Replacement of house fuses or resetting circuit breakers 13 Repairs performed by unauthorized servicers Service calls that do not involve defects in material or workmanship such as customer education door reversal or proper installation Service calls that are related to external problems such as abuse misuse inadequate electrical power accidents fire floods or acts of God Failure of the product if it is used for other than its intended purpose This warranty does not apply outside the continental U S A Z WIRING DIAGRAM 86 C Heater O O O Cooling thermostat AT 3 Overload Protector Red Compressor 95 C 14 AVISO ESTE GRIFO DE AGUA CALIENTE TIENE UN ADAPTADOR DE SEGURIDAD PARA NINOS PARA OBTENER AGUA CALIENTE PASOS RECOMENDADO
14. properly installed grounded wall outlet Do not under any circumstances cut or remove the third ground prong from the power cord Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center This appliance requires a standard 115 120 volt 60Hz electrical outlet with three prong ground The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury Do not use an adapter plug with this appliance Do not use an extension cord with this appliance If the power cord is too short have a qualified electrician or service technician install an outlet near the appliance Cold Water Control Turn the cooling switch on The green indicator will be lit on and the process begins When the water reaches the right temperature the green light goes off automatically z Hot Water Control Turn the heating switch on the red indicator will be lit on and the heating process starts When the water reaches the right temperature the red light goes off automatically When the temperature goes down to approx 80 C 176 F the red indicator will glow again and another heating process starts NOTE THE HOT WATER FAUCET HAS A CHILD SAFETY GUARD ATTACHMENT 10 Cup Dispenser Optional A cup dispenser may be installed by using the mounting holes covered with plastic caps located near the top of the right side panel of th
Download Pdf Manuals
Related Search