Metra MITO-01 car kit
Contents
1. MITO O1 MITO O1 MITSUBISHI DATA BUS INTERFACE INSTALLING AND TESTING THE MITO O1 1 With all connections completed to the radio plug the corresponding harnesses into the MITO 01 2 Cycle the key by turning the ignition on then back off then back on again to test the radio for proper operation 3 If the subwoofer or front door speakers are too loud you can adjust the output by following the steps below A Locate the end of the MITO 01 with the 14 way Molex connector B There are 2 potentiometers next to the Molex connector the one closest to the Molex connector is the subwoofer control and the other one is the front door speaker control SUBWOOFER CONTROL FRONT DOOR SPEAKER CONTROL C Using a small blade screwdriver turn the potentiometer of the speaker you want to adjust either clockwise to make it louder or counterclockwise to lower the volume KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow Rev 03 11 10 INSTMITO 01 G 1 800 221 0932 m www axxessinterface com Copyright 2010 Metra Electronics Corporation MITO 01 INSTALLATION INSTRUCTIONS READ IMPORTANT WARNING ON PAGE 2 BEFORE ATTEMPTING ANY INSTALLATION The MITO 01 is designed to be used in vehicles listed i2. TED TO DO OR BELIEVE THAT YOU DO NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD CONSULT A TECHNICIAN WHO DOES HAVE THIS KNOWLEDGE AND UNDERSTANDING FAILURE TO FOLLOW THESE INSTRUCTIONS CAREFULLY AND TO INSTALL THE INTERFACE AS DESCRIBED COULD CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS ON THE VEHICLE INTERFERENCE WITH CERTAIN SAFETY SYSTEMS COULD CAUSE HARM TO PERSONS AS WELL IF YOU HAVE ANY QUESTIONS IN THIS REGARD PLEASE CALL THE HELP LINE OR THE METRA AT 1 800 221 0932 FOR ASSISTANCE MITO O1 BEFORE WIRING UP THE MITO OI mportant Before beginning any of the following disconnect the negative battery terminal to prevent an accidental short circuit WIRING CONNECTIONS TO BE MADE ON THE VEHICLE SIDE HARNESSES 1 Connect the Yellow wire to the radio s 12 volt battery or memory wire 2 Connect the Red wire to the radios 12 volt ignition or accessory wire 3 Connect the Black wire with the fork connector to a good ground like a metal brace in the dash 4 Connect the Black wire to the radios ground wire 5 Connect the Orange wire to the radios Illumination wire If the radio does not have an Illumination wire just tape up the wire 6 Connect the Blue wire to the radios power antenna turn on wire 7 Connect the White wire to the radios Left Front speaker wire 8 Connect the White Black wire to the radios Left Front speaker wire 9 Connect the Gray wire
3. ircuits 1 Connect the Blue White wire to the radios amplifier turn on wire 2 Connect the Brown wire to the radios mute wire If the radio does not have a Mute wire just tape up the wire 3 Connect the White RCA to the radios left front rca output 4 Connect the Gray RCA to the radios right front rca output 5 Connect the Green RCA to the radios left rear rca output 6 Connect the Purple RCA to the radios right rear rca output lf the radio does not have rca outputs or only 1 pair we recommend the use of the Axxess ALOC648 or ALOC608 line level convertor sold separately The following wires are for radios that have navigation e Connect the Blue Pink wire to the radios VSS or Speed Sense wire e Connect the Green wire to the radios Parking Brake wire e Connect the Green Purple wire to the radios Reverse wire Continued on page 5
4. n the applications that have the Rockford Fosgate audio sys tem The Rockford Fosgate system uses a digital signal to turn on the amplifier The MITO 01 supplies that digital sig nal to turn the amplifier on and also eliminates the COM ERROR message on the display when the OEM radio is removed When installing a radio that has navigation built in the MITO 01 can supply VSS Vehicle Speed Sense Parking Brake and Reverse however Reverse is not avail able on manual transmission vehicles The radios speaker wires will provide the audio for the dash and rear speakers while the rca s will provide the audio to the amplifier to power the door speakers and woofer INTERFACE COMPONENTS e MITO 01 Interface e 14 Pin Harness with RCA s e Vehicle side harness e 2 Pin harness FA 1 800 221 0932 m wwwaxxessinterface com Copyright 2010 Metra Electronics Corporation _ lO OO OO Ss S gt TOOLS REQUIRED FOR INSTALLATION e Cutting Tool e Small Blade Screwdriver Tape Crimping Tool Connectors I E butt connectors bell caps etc APPLICATIONS MITSUBISHI Eclipse 2006 2010 MITSUBISHI Endeavor 2007 2009 IMPORTANT WARNING THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST BE CAREFULLY FOLLOWED THE INSTRUCTIONS ARE WORDED IN SUCH A MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE OF COMPLETING THESE TYPE OF ELECTRONIC INSTALLATIONS IF YOU ARE UNCLEAR AS TO WHAT YOU ARE INSTRUC
5. to the radios Right Front speaker wire 10 Connect the Gray Black wire to the radios Right Front speaker wire 11 Connect the Green wire to the radios Left Rear speaker wire 12 Connect the Green Black wire to the radios Left Rear speaker wire 13 Connect the Purple wire to the radios Right Rear speaker wire 14 Connect the Purple Black wire to the radios Right Rear speaker wire If the radio you are installing has navigation built in the MITO 01 can supply the necessary navigation outputs with some additional wiring The MITO 01 comes with a 2 pin connector with a Pink and a Blue Pink wire in it Follow the steps below to connect these wires to the vehicle 1 Connect the 2 pin connector with loose leads to the mating connector on the vehicle side harness of the MITO 01 2 Locate the OBD2 connector which is located beneath the driver s side dash panel close to the center console and run the Pink and the Blue Pink wires down to it MITSUBISHI Eclipse 2006 2010 a MITSUBISHI Endeavor 2007 2009 3 Take the Pink wire from the 2 pin connector and connect it to pin 6 of the 0BD2 connector 4 Take the Blue Pink wire from the 2 pin connector and connect it to pin 14 of the OBD2 connector OBD2 Connector Face View WIRING CONNECTIONS TO BE MADE ON THE 14 PIN HARNESS WITH RCAS NOTE The RED wire on this harness will not be used Tape up wire to prevent any accidental short c
Download Pdf Manuals
Related Search