Metra 99-7861 mounting kit
Contents
1. terminal to prevent an accidental Short circuit Using a small flat blade screwdriver remove the blank plate from upper right side of radio trim panel Figure A Unsnap radio trim panel Unplug Switches and remove panel Figure B Remove 4 10mm bolts securing radio unplug and remove radio Figure C 99 7861 DASH DISASSEMBLY HONDA PILOT 2006 2008 Without Factory Navigation Disconnect the negative battery terminal to prevent an accidental short circuit Remove 2 screws from the top of the instrument panel trim Unclip and remove the instru ment panel trim Figure A Unclip and remove the left center trim panel Figure B Unclip the radio trim panel Unplug and remove the panel Figure C Remove the 4 screws securing the radio Unplug and remove the radio Figure D Continue to kit assembly 99 7861 KIT ASSEMBLY HONDA PILOT 2003 2008 2006 2008 Without Factory Navigation 1 Select the proper radio housing for your vehicle EX models use radio housing E and LX models use radio housing L The radio housings are labeled on one of the mounting tabs Figure A 2 Mount the pocket to the back of the radio housing with the 2 8x3 8 phillips pan head screws supplied Notches on the pocket must be on top Figure B 3 Mount the rear support bracket to the back of the pocket with the 2 8x3 8 Phillips truss head screws supplied Fi2. INSTALLATION INSTRUCTIONS FOR PART 99 7861 APPLICATIONS Honda Pilot 2003 2008 2006 2008 Without Factory Navigation 99 7861 KIT FEATURES e Recessed DIN e Pocket e ISO Head Unit Provision With Pocket KIT COMPONENTS WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e 70 1721 Honda Acura harness 1998 up Antenna Adapter e 40 HD10 Honda antenna adapter 2005 up TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool Phillips Screwdriver Socket Set SS SOG re 1 800 221 0932 www metraonline com COPYRIGHT 2004 2009 METRA ELECTRONICS CORPORATION REV 06 29 09 E MENT S 99 7861 TABLE OF CONTENTS Dash Disassembly Honda Pilot 2003 2008 1c ccuuuuccuuunecnuuneenueuenuuas 1 Honda Pilot 2006 2008 Without Factory Navigation 2 Kit Assembly ssrsrrrrrssrrorsansansansnnsnnnanne 3 DIN Head Unit Provision With Pocket 1111111111111212 4 ISO Head Unit Provision With Pocket ucuuccuueunenuaee 5 Final ASSCHUAY sirirrirrrrisrirrarinrr ninis irt inertan 6 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow 99 7861 DASH DISASSEMBLY HONDA PILOT 2003 2008 Disconnect the negative battery
3. gure C e E m Marrs 99 7861 KIT ASSEMBLY DIN HEAD UNIT PROVISION WITH POCKET 1 Slide DIN cage supplied with radio into the assembled radio housing from the front Figure A 2 Secure DIN cage to radio housing by bending the locking tabs outward Figure A 3 Slide the radio into the DIN cage until it snaps into place Figure B 99 7861 KIT ASSEMBLY ISO HEAD UNIT PROVISION WITH POCKET 1 Align the holes in the ISO brackets with the holes in the radio Mount the brackets to the radio using screws supplied with the radio Figure A 2 Slide the radio bracket assembly into the assembled radio housing until it snaps into place Figure B 3 Snap the ISO trimplate onto the front B of the assembled radio and housing Figure B NOTE 70 remove the radio unsnap and remove the ISO trimplate Using a flat blade screwdriver disengage ISO brackets from the radio housing and slide radio out of radio housing Saaz _SSESSSSES O O M ZZ 99 7861 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radi
4. o and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Dimmer Orange White 12V Batt Memory Yellow Right Front White Ground Black Left Front White Black Power Antenna Blue Right Rear Violet Amp Turn On Blue White Right Rear Violet Black Amp Ground Black White Left Rear Green lllumination Orange Left Rear Green Black NOTE When Black a wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications G 1 800 221 0932 www metraonline com Rev 06 29 09 COPYRIGHT 2004 2009 METRA ELECTRONICS CORPORATION INST99 7861
Download Pdf Manuals
Related Search