Draper Cineperm
Contents
1. see Fig 1 Stage Left and Stage Right sections should be placed with snaps up Top and bottom sections should be placed with snaps down To increase frame rigidity hinges on top and bottom sections have rivnuts marked with red and green Insert a Handy Crank through the threadless rivnut red and tighten into the threaded rivnut green Apply small sections marked Stiffener Bars to back of bottom frame section using 8 Handy Cranks These eliminate sag on large suspended frames Failure to use all Handy Cranks may result in screen frame damage Turn bottom frame section over so snaps face up Repeat step 3 for top frame section Join top and bottom sections to Stage Left and Stage Right using 2 Handy Cranks on each of the 4 corners Match numbers on white labels NOTE No Handy Crank should protrude outside screen frame Attach surface see Surface Installation and suspend using appropriate materials provided by others to meet specific installation requirements i Color coded tape ml H of H Standard Frame Truss Style Frame Figure 1 Frame Installation Standard Frame Outside Face Mount Drill mounting holes in frame see Fig 2 Mark wall and drill holes to correspond with those in the frame Attach frame to wall using appropriate fasteners for mounting surface provided by others NOTE Measure screen frame width at the top bottom and center Make sure the frame2. Installation Instructions Cineperm Permanently Tensioned Projection Screen by Draper Caution Read instructions through completely before proceeding Follow instructions carefully Installation contrary to instructions invalidates warranty Bent or warped frames will affect surface flatness and image quality Screen should be square and width should not vary from the center to the ends of the frame When lifting assembled screen do not lift at only one corner lift at both corners Lifting by one corner could result in damage to the screen frame especially on large screens Screen should be installed level using a carpenter s level Nothing should be fastened to screen frame or viewing surface Be careful not to rip screen material when attaching surface to frame The ideal temperature range for assembling this screen to prevent damaging the surface is 68 78 F 20 26 C Assembling below recommended temperatures may damage surface and void warranty NOTE Screen has been inspected and tested at factory prior to shipment Frame Assembly Standard Frame Lay out frame pieces on floor by matching up color coded tape near corners Snaps should be facing up Assemble frame see Fig 1 If necessary gently tap frame ends with a rubber mallet to make sure castings are fully seated Truss Frame Unfold and lay out pieces on floor by matching up color coded marks Lock all hinges
3. aution when attaching fabric Overstretching or rough handling could cause the viewing surface to tear Outside Face Mount Wall Nw Enlarge holes in frame side furthest from wall to allow screw heads to pass Anchor bolt by others through see Fig 2 Do not allow screw heads to remain outside the frame overtightening could bend frame and affect screen flatness 411 S Pearl St Spiceland IN 47385 USA I 765 987 7999 www draperinc com I fax 765 987 7142 Copyright 2011 Draper Inc Form Cineperm_Inst 1 Printed in U S A Clearance wall in outer wall by others Locate between snaps a Snap on viewing surface Always fold viewing surface with snaps face to face 4 Do not permit screen fabric to contact border material or snaps when folded Store in pouch provided Inside Jamb Mount 1 square Opening alum tube Wall NZ Anchor bolt by others hh Clearance hole in outer wall by others F 1 square alum tube Snap on viewing surface If you encounter any difficulties installing or servicing your Cineperm call your dealer or Draper Inc in Spiceland Indiana 765 987 7999 or fax 765 987 7142
4. is installed so the center width is same as the width at the top and bottom Drill through frame for mounting hardware Enlarge first hole for screw head to pass through Supporting struc Cineperm frame u oO Mounting hardware Viewing surface snaps to by others frame covering mounting holes Figure 2 Inside Jamb Mount Place frame assembly in opening to check for a snug fit If frame is too large opening may have to be enlarged If frame is too small or does not sit square in the opening shims and caulking may be required Drill mounting holes in frame and enlarge the first holes to allow screw heads to pass through see Fig 3 Do not allow screw heads to remain outside the frame overtightening could bend frame and affect screen flatness Drill holes in jamb Attach frame using appropriate fasteners for mounting surface provided by others Use caulk to ensure there is no light leakage around edges of frame Cineperm Jamb of opening frame Drill through frame for mounting hardware Enlarge first hole for screw head to pass through 7 Mounting hardware by others Ww Viewing Surface snaps to frame covering mounting holes Figure 3 Surface Installation Carefully remove surface from cardboard tube and unroll onto a clean cloth or paper Engage snaps in each corner then secure rest of screen snaps Stretch fabric across frame Use extreme c
Download Pdf Manuals
Related Search