Smeg SE2951TC2 hob
Contents
1. On first installing within two minutes of powering on the hob hold down buttons and m for the first cooking zone the one near symbol O The cooking zone display will show the number of the setting currently being modified 1 automatic control lock 2 showroom 3 ECO logic with its setting at the side El active EI inactive For example EI EI indicates that the automatic control lock is inactive Use buttons and m to change the setting to ET or to H if changing the ECO logic parameter the following may be selected 8 2 8 kW LI 4 kW EI maximum power absorbed To advance and change the subsequent settings press button Ol If the hob is already installed and in use cut the power supply to the hob Switch the power back on and S7 proceed as indicated above within two minutes 47 Instructions for the user ex 6 13 Cooking guidelines The table below shows the power values which can be set together with the corresponding type of food Settings may vary depending on the amount of food and personal taste SETTING TYPE OF FOOD U 1 To melt butter chocolate or similar products To heat food keep small amounts of water on the boil and whip up sauces with eus egg yolk or butter 4 5 To heat solid or liquid food keep water on the boil defrost deep frozen food cook 2 or 3 egg omelettes fruit and vegetables various cooking processes 6 To stew meat fish and vegetables simmer food make jams etc 7 8 To r2. ARE ALWAYS KEPT CLEAN AS THE APPLIANCE MAY INTERPRET DIRTY MARKS AS AN INTENTIONAL FINGER CONTACT DO NOT PLACE OBJECTS OF ANY KIND SAUCEPANS TOWELS ETC ON THE SENSORS IF FOOD OVERFLOWS ONTO THE SENSOR BUTTONS YOU ARE ADVISED TO TURN OFF THE APPLIANCE AFTER USE SWITCH OFF THE COOKING ZONE IMMEDIATELY USING THE RELATIVE BUTTONS f f SAUCEPANS AND OTHER PANS MUST NOT COVER THE SENSOR BUTTONS AS THE APPLIANCE MAY AUTOMATICALLY DEACTIVATE ACTIVATE THE BUTTON LOCK WHEN YOU HAVE CHILDREN OR PETS WHICH COULD REACH THE HOB MW 3 X 27 A General instructions GB IE DO NOT PUT EMPTY SAUCEPANS AND FRYING PANS ON COOKING ZONES WHICH HAVE BEEN SWITCHED ON DO NOT USE THE HOB IF PYROLYSIS IS TAKING PLACE INSIDE ANY OVEN INSTALLED BELOW The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original spare parts 33 GB IE 3 E General instructions 2 SAFETY PRECAUTIONS CONSULT THE INSTALLATION INSTRUCTIONS FOR THE SAFETY STANDARDS APPLICABLE TO ELECTRICAL APPLIANCES AND FOR THE VENTILATION FUNCTIONS IN YOUR INTERESTS AND FOR YOUR SAFETY IT HAS BEEN ESTABLISHED BY LAW THAT THE INSTALLATION AND SERVICING OF ALL ELECTRICAL APPLIANCES IS TO BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE OUR APPROVED INSTALLERS G
3. heat active This signal will clear within 5 minutes 37 Instructions for the user end 5 GET TO KNOW YOUR APPLIANCE The appliance has cooking zones with various diameters and power levels depending on the model Their position is clearly indicated with circles and the heat is limited to within the diameters traced on the glass The cooking zones are of the HIGH LIGHT type they turn on after a few seconds and the heating is adjustable using the controls on the front panel The cooking zones with two or three concentric circles allow double or triple heating either within the small circle or on both circles 5 1 Layout of the cooking zones 60 cm hobs without a frame hobs with a frame 38 Instructions for the user GB IE Outside Max power Inside Max power Middle Max power Zone diameter absorbed W diameter absorbed W diameter absorbed W mm mm E mm 150 1200 185 2000 124 800 5 185 1800 215 2400 148 1100 oval plate 2200 170 1400 gt 200 2000 power levels are indicative and can vary according to the settings made and the mains voltage 290 2700 150 1950 216 1050 5 2 Power levels The power in the cooking zone can be adjusted to various levels The table shows the levels suitable for various types of cooking Power level Suitable for 0 OFF position U Dishwarming 1 2 Cooking small amounts of food minimum power 3 4 No
4. much the glass may be strained causing it to 55 GB IE A E i Z 4 P 56 Instructions for the installer 9 8 Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing Do not remove this plate for any reason THE HOB MUST BE CONNECTED TO THE ELECTRIC SUPPLY BY A QUALIFIED TECHNICIAN BEFORE ANY INTERVENTION DISCONNECT THE POWER SUPPLY OF THE HOB THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS WHERE THE APPLIANCE 15 CONNECTED TO THE POWER GRID VIA A PLUG AND SOCKET BOTH OF THESE MUST BE OF THE SAME TYPE AND CONNECTED TO THE POWER CABLE IN ACCORDANCE WITH THE APPLICABLE REGULATIONS THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN NEVER UNPLUG BY PULLING ON THE CABLE IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE HOB FOLLOWING THE INSTRUCTIONS IF THE HOB FAILS TO OPERATE AFTER CHECKING THAT YOU HAVE CARRIED OUT THE INSTRUCTIONS CORRECTLY DISCONNECT THE APPLIANCE FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE RUN THE POWER CABLE UNDER THE UNIT TAKING CARE THAT IT DOES NOT COME INTO CONTACT WITH THE BOTTOM OF THE CASING OF THE HOB OR THE OVEN BENEATH IT IF THERE IS ONE THE EARTHING WIRE MUST BE LONGER THAN THE CURRENT CONDUCTION
5. of your appliance it is important to remove doors and leave shelves in the same position as for use to ensure that children cannot accidentally become trapped inside during play It is also necessary to cut the connecting cable to the power supply network removing it along with the plug Instructions for the user GB IE 4 BEFORE FIRST USE Before cooking for the first time all labels and protective films applied to the inside or outside of the appliance must be removed and the hob subsequently cleaned Following this put a saucepan of water on the front hot plates and turn them on full for at least 30 minutes After 30 minutes turn off the front hot plates and turn the rear hot plates and the central hot plate if present full on This treatment is necessary in order to get rid of the new smell and to evaporate any humidity that may have accumulated during the manufacturing process This is necessary to ensure that the electronic circuits and the control keyboard work properly If the controls do not work properly after 30 minutes it means that not all the humidity has evaporated leave the hot plates on until all the humidity has evaporated and then turn off the hob To switch on the hob follow the instructions provided under paragraph 6 Using the hob When first connecting to the mains EI may be displayed This does not mean that the hot plates are hot but that during factory testing the hob was switched off with residual
6. timer does not switch off the cooking zones but rather informs the user when the set time has run out The timer can be activated while the cooking zones are on or off 6 10 2 of set time At the end of the previously set time the hob will warn the user with a series of buzzers Press button O to stop the buzzer 6 10 3Deactivating the timer To deactivate the timer during the countdown zero the set time using button m When the display shows ET the timer has been deactivated 45 Instructions for the user end 46 6 11 Cooking zone automatic shutdown timer on some models only This function is used to program the automatic shutdown of each cooking zone at the end of a period of time from 1 to 99 minutes 6 11 1Setting the cooking time Press the button and the display will show E to indicate the timer is being set see 6 10 Timer on some models only Press button again if at least one cooking zone is on and a lighted dot will appear under the controls of the first active zone from left to right the automatic shutdown time can now be selected by pressing button or m hold the buttons down to set the time more quickly or select another hot plate using button Ol If the timer is activated with no cooking zone active it will behave as described previously see 6 10 Timer on some models only 6 11 2Changing the set time Press the button O until a lighted dot appears un
7. AFTER THEY HAVE BEEN TURNED OFF KEEP CHILDREN AWAY FROM THE COOKING ZONES IF CRACKS OR FISSURES FORM OR IF THE GLASS CERAMIC COOKING SURFACE BREAKS TURN OFF THE APPLIANCE IMMEDIATELY DISCONNECT THE ELECTRICITY SUPPLY AND CALL TECHNICAL SUPPORT THIS APPLIANCE MUST NOT BE USED BY PEOPLE INCLUDING CHILDREN OF REDUCED PHYSICAL AND MENTAL CAPACITY OR LACKING IN EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES UNLESS THEY ARE SUPERVISED OR INSTRUCTED BY ADULTS WHO ARE RESPONSIBLE FOR THEIR SAFETY BEFORE THE APPLIANCE IS PUT INTO OPERATION ALL LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED NEVER ATTEMPT TO REPAIR THE APPLIANCE ALL REPAIRS MUST BE CARRIED OUT BY AN AUTHORISED TECHNICIAN OR AT AN AUTHORISED SERVICE CENTRE General instructions GB IE NEVER LEAVE THE SWITCHED ON HOB UNATTENDED BE AWARE OF HOW RAPIDLY THE COOKING ZONES HEAT UP DO NOT PLACE EMPTY SAUCEPANS ON THE HEAT DANGER OF OVERHEATING FAT AND OIL CAN CATCH FIRE IF THEY OVERHEAT YOU ARE THEREFORE RECOMMENDED NOT TO LEAVE THE HOB WHILE PREPARING FOODS CONTAINING OIL OR FAT IF FAT OR OIL CATCHES FIRE NEVER PUT WATER ON IT COVER THE PAN AND SWITCH OFF THE COOKING ZONE THE GLASS CERAMIC SURFACE IS HIGHLY RESISTANT TO IMPACTS HOWEVER DO NOT ALLOW HARD SOLID OBJECTS TO FALL ON THE COOKING SURFACE AS THEY MAY CAUSE IT TO BREAK IF THEY ARE SHARP THE GLASS CERAMIC COOKING SURFACE MUST NOT BE USED AS A SURFACE FOR PLACING
8. Contents FOR USE xui 32 2 SAFETY PRECAUTIONS q e 34 Ss ENVIBONMENIBAL CARE uu uuu nm 36 3 1 Our environmental 36 32 Your SnVIrODImeni3al Caro MEE mc 36 BEFORE FIROT USE KE 37 5 GET TO KNOW YOUR APPLIANCE 38 5 1 Layout ol COOKINO RT cr 38 5 2 x0 di 39 5 3 Adyice on energy SavViNO u uuu EE TTE TET 39 5 4 Limiting the cooking duration a nen nennen nennen nene nnne 40 5 5 Protection from hob overheating r 40 sacs divise Ae 40 SA wCHia ji CE 41 6 1 General warnings and advice EK Vau ENIM P 41 O Oi pO y EE 41 Oi SIC ING OM INE NOD spss u u u uu nu out PM 42 6 4 Switching on a single hot plate seessssssssssssssseeeee nennen nnne nnne n
9. INGS AND SLITS PROVIDED FOR VENTILATION AND HEAT DISPERSAL DO NOT USE THIS APPLIANCE FOR HEATING ROOMS hj THE IDENTIFICATION PLATE CONTAINING THE TECHNICAL DATA SERIAL NUMBER AND BRAND NAME 1S IN A VISIBLE POSITION UNDER THE CASING OF THE APPLIANCE A COPY OF THE IDENTIFICATION PLATE IS INCLUDED IN THE BOOKLET IT SHOULD BE APPLIED TO THE APPROPRIATE SPACE ON THE BACK OF THE COVER DO NOT REMOVE THIS PLATE FOR ANY REASON BEFORE THE APPLIANCE IS PUT INTO OPERATION ALL LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED TAKE CARE NOT TO SPILL SUGAR OR SWEET MIXTURES ON THE HOB WHILE COOKING OR TO PLACE MATERIALS OR SUBSTANCES WHICH COULD MELT ON IT PLASTIC OR TINFOIL IF THIS HAPPENS TO AVOID DAMAGE TO THE SURFACE TURN OFF THE HEAT IMMEDIATELY AND CLEAN THE SURFACE WITH THE SCRAPER PROVIDED WHILE THE HOT PLATE IS STILL WARM IF THE GLASS CERAMIC HOB IS NOT CLEANED IMMEDIATELY THERE IS A RISK THAT INCRUSTATIONS WILL BE LEFT THAT ARE IMPOSSIBLE TO REMOVE ONCE THE HOB HAS COOLED DO NOT USE METALLIC SPONGES THEY WILL DAMAGE THE SURFACE USE NORMAL NON ABRASIVE PRODUCTS A WOODEN OR PLASTIC TOOL IF NECESSARY e NEVER PLACE SAUCEPANS WITH BASES WHICH ARE NOT PERFECTLY FLAT AND SMOOTH THE COOKING HOB MP THE APPLIANCE BECOMES VERY HOT DURING USE SUITABLE HEAT PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS Guy a ENSURE THAT THE SENSOR BUTTONS
10. OBJECTS IF IT BECOMES IMPOSSIBLE TO TURN OFF THE HOB DUE TO A SENSOR FAULT IN THE CONTROL IMMEDIATELY DISCONNECT THE ELECTRICITY SUPPLY AND CALL TECHNICAL SUPPORT BE CAREFUL WHEN CONNECTING ADDITIONAL ELECTRICAL APPLIANCES CONNECTION CABLES MUST NOT COME INTO CONTACT WITH HOT COOKING ZONES NEVER PLACE FLAMMABLE READILY EXPLOSIVE OR DEFORMABLE OBJECTS DIRECTLY UNDERNEATH THE HOB DO NOT USE SEALED TINS OR CONTAINERS ON THE APPLIANCE OVERPRESSURE MAY OCCUR INSIDE THE CONTAINERS DURING COOKING CREATING A DANGER OF EXPLOSION IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS DO NOT USE IT AS A ROOM HEATER The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original spare parts 35 Instructions for disposal A 36 3 ENVIRONMENTAL CARE 3 1 Our environmental care Pursuant to Directives 2002 95 EC 2002 96 EC 2003 108 EC relating to the reduction of the use of hazardous substances in electrical and electronic appliances as well as to the disposal of refuse the crossed out bin symbol on the appliance indicates that the product at the end of its useful life must be collected separately from other refuse Therefore the user must consign the product that has reached the end of its working life to the appropriate selective collection centres for electrical
11. UARANTEE A SATISFACTORY JOB ELECTRICAL APPLIANCES MUST ALWAYS BE UNINSTALLED BY COMPETENT PERSONS BEFORE CONNECTING THE APPLIANCE TO THE POWER GRID CHECK THE DATA ON THE PLATE AGAINST THE DATA FOR THE GRID ITSELF BEFORE CARRYING OUT INSTALLATION MAINTENANCE WORK MAKE SURE THAT THE APPLIANCE IS NOT CONNECTED TO THE POWER GRID IMMEDIATELY AFTER INSTALLATION CARRY OUT A QUICK TEST ON THE APPLIANCE FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL SHOULD THE APPLIANCE NOT FUNCTION DISCONNECT IT FROM THE POWER SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND ITS SOCKET MUST BE OF THE SAME TYPE AND CONFORM TO THE REGULATIONS IN FORCE THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN NEVER UNPLUG BY PULLING ON THE CABLE IF THE POWER SUPPLY CABLE IS DAMAGED CONTACT THE TECHNICAL SUPPORT SERVICE IMMEDIATELY AND THEY WILL REPLACE IT THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS DURING COOKING THE APPLIANCE BECOMES VERY HOT IN THE ZONE IN CONTACT WITH THE PANS TAKE CARE NOT TO TOUCH THE SURFACE OF THE HOB THE APPLIANCE IS INTENDED FOR USE BY ADULTS DO NOT ALLOW CHILDREN TO GO NEAR IT OR PLAY WITH IT IMPORTANT BEWARE OF CHILDREN IN THE VICINITY AS THE WARNING LIGHTS INDICATING RESIDUAL HEAT ARE OUT OF THEIR LINE OF SIGHT THE COOKING ZONES REMAIN HOT FOR A CERTAIN PERIOD OF TIME EVEN
12. WIRES SO THAT IF THE PLUG IS TORN OFF THE POWER CABLE IT IS THE LAST TO BE DETACHED AVOID USE OF ADAPTERS AND SHUNTS AS THESE COULD CAUSE OVERHEATING AND RISK OF BURNS WHERE A FIXED CONNECTION IS IN USE A MULTIPOLAR CUT OUT DEVICE MUST BE INSTALLED ON THE SUPPLY CABLE WITH A CONTACT OPENING DISTANCE EQUAL OR GREATER THAN 3 MM LOCATED IN A READILY REACHABLE POSITION NEAR THE APPLIANCE The manufacturer declines all responsibility for damage to persons or things caused by the non observance of the above indications or as a result of tampering with any part of the appliance Instructions for the installer GB IE HOB TYPE POSSIBLE CONNECTION CABLE TYPE CM TYPES if not present 380 415 V 3N 5 pole 5 x 1 5 mm HO5V2V2 F 123 45 aM 380 415 V 2N HO5V2V2 F 1 4 5 QD 2 3 in 220 240 V 3 HO5V2V2 F 60 70 90 220 240 V 1N HO5V2V2 F 1 2 3 4 5 220 HO5V2V2 F e e Head the connection layout plate underneath the appliance or around the power cable with care Use HO5V2V2 F cables resistant to at least 90 C The aforementioned power cables are sized taking into account the coincidence factor in compliance with standard EN 60335 2 6 P 57 Instructions for the installer 9 8 1 Terminal diagram The adjacent diagram illustrates the power supply terminal from below with no cables connected Terminals 4 and 5 must be connected at all times 58
13. ally If the control lock function has been activated after pressing button the displays will show r1 8 8 or 8 on some models only The control lock must be deactivated in order to switch on the hob see 6 8 Control lock 6 4 Switching on a single hot plate After switching on the hob press buttons to activate the required hot plate the display will show symbol ERI Press symbol and the display will show 9 or depending on the model This means that the hot plate is on at maximum power Press symbol or m to increase or decrease the required power level If button is pressed when the hot plate is at maximum power the hot plate will switch off E Press the button again to switch on the hot plate The selection will now be gradual from 1 to 9 or from 1 to P on some models only In position the hot plate cannot be switched on by pressing button Bm 6 5 Switching on a double hot plate To start heating a double hot plate after having set the maximum power level or on some models only press button nm A lighted dot will appear adjacent to the power to indicate the hot plate has been fully activated Press button or m to increase or decrease the required power level If button is pressed when the hot plate is at maximum power the hot plate will switch off E Instructions for the user GB IE 6 6 Switching on a triple hot plate To start heating a triple hot plate after having s
14. and electronic refuse or deliver it back to the retailer when purchasing an equivalent product on a one for one basis Adequate selective collection for the subsequent forwarding of the decommissioned product to recycling treatment and ecologically compatible disposal contributes to avoiding possible negative effects on the environment and on health and promotes the recycling of the materials of which the appliance consists The illicit disposal of the product by the user results in the application of administrative sanctions The product does not contain substances in quantities sufficient to be considered hazardous to health and the environment in accordance with current European directives 3 2 Your environmental care Our product s packaging is made of non polluting materials therefore compatible with the environment and recyclable Please help by disposing of the packaging correctly You can obtain the addresses of collection recycling and disposal centres from your retailer or from the competent local organisations Do not discard the packaging or any part of it or leave it unattended It can constitute a suffocation hazard for children especially the plastic bags Your old appliance also needs to be disposed of correctly Important hand over your appliance to the local agency authorised for the collection of household appliances no longer in use Correct disposal enables intelligent recovery of valuable materials Before disposing
15. der the controls of the zone whose set time is to be changed Once the relevant zone is selected use button or to change the previously selected time 6 11 3End of set time At the end of the previously set time the hob will deactivate the cooking zone and warn the user with a series of buzzers Press any button to stop the buzzer The automatic shutdown timer can be used like a simple timer Follow the previous instructions without selecting the cooking zone power level Instructions for the user GB IE 6 12 Secondary menu Automatic control lock Showroom ECO logic The hob is equipped with a secondary menu for activating or deactivating some parameters 1 Automatic control lock on activating this mode one minute after the last operation by the user the controls will automatically be locked see 6 8 Control lock 2 Showroom on activating this mode the appliance deactivates all the heating elements while keeping the control panel active useful for demonstration purposes in store To use the hob normally set this mode to n rep If showroom mode has been activated 5 EI 8 will display every minute for one second 3 ECO logic on some models only on activating this mode the hob electronics will automatically m ECO adjust the power levels to stay within the set maximum power absorbed 2 8 or 4 kW To use the hob logic at maximum power set this mode to n 6 12 1 Changing the settings in the secondary menu
16. e refer to the actual dimensions of your glass ceramic hob before cutting L mm X mm Y mm G mm H mm A mm B mm C mm 600 565 490 604 519 50 min 50 min 750 min 770 745 490 774 519 50 50 750 min After laying the adhesive sponge A on the glass B surface see 9 4 Hob seal and after positioning and securing the hob fill the edges with insulating silicone B and wipe away any excess In the event the glass surface has to be removed cut the silicone using a cutter before attempting to remove it C Enough silicone must be used to create a seal between the hob and the counter top but not so much N as to fasten the appliance To fasten the appliance see 9 7 Fixing using brackets lt C 54 Instructions for the installer 9 6 Positioning the fastening clips To ensure the hob is fixed and centred as accurately as possible the clips provided must be positioned as described below Fit the clips by gently pressing them horizontally into the appropriate space Then turn them upwards to fix them in place 9 7 Fixing using brackets Fix the hob to the unit using the appropriate brackets supplied To secure the hob correctly to the counter top tighten the brackets A in the appropriate holes on the sides of the casing Take care while securing with the brackets if tightened too
17. e turns off a short alert is sounded and if the zone is hot the symbol will show on the display Power level set Maximum cooking duration in hours U 1 10 2 6 3 5 4 4 5 3 6 7 8 2 9 P 1 5 5 Protection from hob overheating If the hob is used on full power for a long period the electronics will have trouble cooling down if the room temperature is high To prevent the electronics overheating a device will trigger to cut power to the front cooking zones and and n will flash If the electronic circuit board temperature does not reduce the device will cut power to all the cooking zones and EI EI ri will display on some models only Cooking can be resumed once the temperature returns below alarm levels The rear cooking zones are recommended for prolonged cooking at high power levels 5 6 Other functions Pressing three or more controls at the same time or for a long period e g due to accidentally placing a saucepan on them or due to an overflow of liquid deactivates all the cooking zones if they are on and the display will show Remove the object from the buttons MEM Instructions for the user GB IE 6 USING THE HOB 6 1 General warnings and advice On first connection to the electrical mains an operating check will be carried out automatically and all the indicator lights will come on for a few seconds When first connecting to the mains may be displayed This does not mean that the
18. et the maximum power level 9 or on some models only press button nm A lighted dot will appear adjacent to the power to indicate the inside hot plate has been activated or RI press button again to fully activate the hot plate The dot adjacent to the power will flash EX Press button or to increase or decrease the required power level If button is pressed when the hot plate is at maximum power the hot plate will switch off E 6 7 Accelerator function This function can be used to reach the selected heating level more quickly The cooking zones will start at maximum power Once the selected power level is reached power is reduced 6 7 1 Activating the accelerator function Press buttons and m simultaneously for the zone to be heated using the accelerator function EI will flash on the display Use buttons and m to select a power level between 1 and 9 the cooking zone can also be activated in double or triple mode The display alternately shows EI and the power level just selected If no power level is selected within 5 seconds of activating the function EI the cooking zone returns to normal status Power level set with A Maximum time to reach min 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 10 9 12 43 GB IE Instructions for the user app M 6 8 Control lock Control lock is a device that protects the appliance from accidental or inappropriate use Useful for 44 preventing accidental changes t
19. f the appliance immediately Disconnect the hob from the power supply and call Technical Support 2 Instructions for the installer GB IE 9 INSTALLATION 9 1 Safety instructions for installing in kitchen units USE PERSONAL PROTECTIVE EQUIPMENT INSTALLING THE APPLIANCE The manufacturer declines all responsibility for damage to persons or things caused by the non observance of the above indications or as a result of tampering with any part of the appliance Veneers adhesives or plastic coatings on adjacent furniture should be temperature resistant gt 90 If they are not sufficiently temperature resistant they may warp over time The minimum distance between a ventilation hood and the cooking surface must be at least the distance indicated in the ventilation hood installation instructions The minimum distances must also be respected for the edges of the hob on the back as indicated in the installation illustrations 9 2 Section cut from the work surface The following operation requires building and or carpentry work so must be carried out by a competent tradesman Installation can be carried out on various materials such as masonry metal solid wood or plastic laminated wood as long as they are heat resistant T 90 C Create an opening in the counter top with the dimensions shown in the figure keeping a minimum distance of A from the rear edge This appliance can be mounted against walls higher than the w
20. hot plates are hot but that during factory testing the hob was switched off with residual heat active This signal will clear within 5 minutes 6 2 Control panel All the appliance s control and monitoring devices are placed together on the front panel The hob is controlled by means of the Touch Control sensor buttons Lightly touch a symbol on the glass ceramic surface The buzzer will sound to confirm every effective touch Function buttons ON OFF button this button is used to switch the hob on or off Control lock button activates or deactivates the control lock if pressed for 3 seconds Increase button increases the power level or cooking time Decrease button reduces the power level or cooking time Timer button activates the timer for the automatic shutdown OL ER OS Identification symbols Hot plate front left Hot plate front left Hot plate rear left Hot plate front left Hot plate centre Placed adjacent to the hot plate symbol it indicates a multiple hot plate Hot plate rear right Hot plate front right 41 Instructions for the user end f f f f 42 6 3 Switching on the hob When not in use the hob will be completely off Hold down button for two seconds to switch on the hob A LED on the hob will light up to indicate the hob is on If no function is activated within 30 seconds of switching on the hob switches off automatic
21. nne e nnne nnn nnn nnn nnne 42 6 5 Switching on double hot plate 42 6 6 Switching on a triple hot plate MR RT 7 43 AcCGOl ralOr uuv Em 43 O CO ear 44 6 9 Residual Neat uuu uuu 44 6 10 Timer on some models only ense qoa a aa node 45 6 11 Cooking zone automatic shutdown timer on some models only 46 6 12 Secondary menu Automatic control lock Showroom ECO logic 47 6 15 ever d aeg Piles ns MET EET Emme 48 7 CLEANING AND MAINTENANCE sseesseesseeennnnnene nnnm nnne nnne a a 49 ne Glass Coralie Dolu u u UOTE 49 7 2 Weekly cleaning E em 49 i0 SES IDCM eee 50 I TACA TON 51 9 1 Safety instructions for installing in kitchen units 51 9 2 Section cut rom Ihe Work SUTOCB Eau aUo Etapas UE STR Kd Gus P UN 51 renim 52 n 53 9 5 Cutting out
22. o remove the double layer base using suitable equipment e max 50mm opens on bottom opens on rear 52 Instructions for the installer GB IE 9 3 2 Over built in oven If installed on top of an oven the latter must be equipped with a cooling fan The distance between the hob and the kitchen furniture or other installed appliances must be enough to ensure sufficient ventilation and air discharge If installed above an oven a space of at least 5 cm must be left between the hob and the top of the appliance installed below c gt m opens only on bottom opens on bottom and on rear 9 4 Hob seal To prevent leakage of liquid between the frame of Y the hob and the work surface place the seal provided along the entire outer edge of the hob WS before assembly Yj N I Do not fix the hob using silicon as this would make it impossible to remove the hob if necessary without damaging it 5 Instructions for the installer 9 5 Cutting out the counter top only on models without frame with straight edge The illustrations indicate the additional cutting and milling dimensions to be used for the hole made in the counter top if the hob is to be installed flush with the work surface The counter top cutting and milling dimensions are purely indicativ
23. o set cooking values the lock can be activated while the hob is on or off 6 8 1 Activating the control lock After switching on the hob press button for at least 2 seconds a lighted dot will appear above the symbol The controls are now locked and if any buttons are pressed DEHE or Sle will display on some models only For safety reasons button D when at least one hot plate is on remains active The entire hob can be switched off at any time even if the lock is active 6 8 2 Deactivating the control lock Press button for at least 2 seconds the lighted dot above the symbol will disappear The controls are now unlocked and any button may be pressed 6 9 Residual heat If the cooking zone is still hot after being switched off the symbol will appear on the display Beware of children in the vicinity as the warning lights indicating residual heat are out of their line of sight The cooking zones remain hot for a certain period of time even after they have been turned off Make sure that children never touch the hob Instructions for the user GB IE 6 10 Timer on some models only This function is used to set a timer which will sound a buzzer at the end of the pre set time from 1 to 99 minutes 6 10 1 Setting the timer Press the button O and the display will show to indicate the timer is being set Set the required time using button or m hold the buttons down to set the time more quickly Using the
24. oast meat fish steaks and liver to saut meat fish eggs etc 9 P To deep fry potatoes etc or bring water to the boil rapidly on some models only For best cooking results and energy saving only use containers suitable for electric cooking The bases of containers must be very thick perfectly flat and clean and dry The hob must also be clean and dry Do not use cast iron saucepans or saucepans with a rough base as they may scratch the cooking surface The diameter of the base of the saucepans must be equal to the diameter of the circle outlining the cooking zone If not energy will be wasted 48 LEA Instructions for the user GB IE 7 CLEANING AND MAINTENANCE Before performing any operations requiring access to powered parts disconnect the appliance from the power supply Do not use a steam jet for cleaning the appliance 7 1 Cleaning the glass ceramic hob The glass ceramic hob should be regularly cleaned preferably after every use once the residual heat warning lights have gone off Smudges from aluminium based pans can be easily cleaned off with a cloth dampened vinegar Remove any burnt residues after cooking with the scraper provided rinse with water and dry thoroughly with a clean cloth Regular use of the scraper considerably reduces the need for chemical detergents for the daily cleaning of the hob Never use abrasive or corrosive detergents e g cleaning products o
25. ork surface on condition that a minimum distance of B be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating Make sure there is a minimum distance of C mm between the hob and any shelf that may be installed directly above it 9 2 1 Hobs without a frame 57 40 L mm X mm Y mm A mm B mm C mm 300 270 490 50 min 50 min 750 min 600 565 490 50 min 50 min 750 min 770 745 490 50 min 50 min 750 min 900 850 490 50 min 50 min 750 min If installing flush with a straight edged work surface follow the instructions in paragraph 9 5 Cutting out the counter top only on models without frame with straight edge 51 Instructions for the installer 9 2 2 Hobs with a frame L mm X mm Y mm A mm B mm C mm 570 560 500 50 min 50 min 750 min 760 750 500 50 min 50 min 750 min 9 33 Mounting 9 3 1 Over empty kitchen unit or drawers with sharp or hot parts The manufacturer declines all responsibility for damage to persons or things caused by failure to comply with the above guidelines Failure to install the double layer wooden base exposes the user to possible accidental contact If there are other pieces of furniture lateral walls drawers etc dishwashers or refrigerators under the hob a double layer wooden base must be installed at least 30 mm from the bottom of the hob to avoid any accidental contact It must only be possible t
26. rmal cooking 5 6 Cooking large quantities of food roasting larger portions 7 Roasting slow frying with flour 8 Roasting 9 P Roasting browning cooking maximum power on some models only 5 3 Advice on energy saving Below you will find advice on how to use your hob effectively and economically e The diameter of the base of the saucepan must correspond to the diameter of the cooking zone e When buying a saucepan check whether the diameter indicated is that of the base or the top of the container as the top is almost always larger than the base e When preparing dishes with long cooking times you can save time and energy by using a pressure cooker which also makes it possible to preserve the vitamins in the food e Make sure that the pressure cooker contains enough liquid as if there is not enough and it overheats this may cause damage to both the pressure cooker and the cooking zone f possible always cover saucepans with a suitable lid e Choose a saucepan suitable for the quantity of food to be cooked A large half empty saucepan leads to a waste of energy 39 Instructions for the user end 40 54 Limiting the cooking duration The hob has an automatic device which limits the duration of use If the cooking zone settings are not changed the maximum duration of operation of each zone depends on the power level selected When the device for limiting the duration of use is activated the cooking zon
27. the counter top only on models without frame with straight edge 54 9 6 T OSIMONING the TESTO g OUPS INE BUE A 55 9 7 FIXING USING DrG6k6818_ u ULU em 55 9 El ectrieal COMING CHO MM mS 56 INSTRUCTIONS FOR THE USER these instructions contain user recommendations a description of the controls and the correct procedures for cleaning and maintenance of the appliance INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified technician who must install the appliance set it functioning and carry out an inspection test 31 General instructions 1 INSTRUCTIONS FOR USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE WE ADVISE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE HOB INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE THIS APPLIANCE IS INTENDED FOR DOMESTIC USE AND CONFORMS TO THE EC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS COOKING AND HEATING UP FOOD ALL OTHER USES ARE CONSIDERED UNSUITABLE THE MANUFACTURER CANNOT BE HELD LIABLE FOR USES OTHER THAN THOSE INDICATED NEVER OBSTRUCT THE OPEN
28. tructions for the user 8 TROUBLESHOOTING PROBLEM The hob does not work The results of cooking are unsatisfactory The hob smokes The error code E2 is displayed and an acoustic signal is temporarily heard An E1 E4 E5 error code is displayed The fuses or the magnetothermal switch of the appliance are repeatedly triggered There are cracks or fissures in the hob 50 POSSIBLE CAUSES The hob is not wired in or the main switch is not on There is a power failure The fuse or the magnetothermal switch of the appliance has blown The sensor buttons are locked control lock The buttons are partially covered by a damp cloth a liquid or a metal object Temperature is too high or too low The hob is dirty Food has spilled onto it he touch control buttons have been activated due to food falling on the hob saucepans or other objects There is a technical fault SOLUTION Switch on the main switch Check power supply Replace the fuse or reactivate the magnetothermal switch of the appliance Unlock the sensor buttons control lock Hemove the obstacle Consult cooking guidelines Clean the hob once cooking is finished Let it cool first Use a larger saucepan Clean the surface or remove the object Contact Technical Support Call Technical Support or an electrician If cracks or fissures form or if the glass ceramic cooking surface breaks turn of
29. ven sprays spot removers and wire sponges Dirt which may have fallen on the hob while cleaning lettuce or potatoes can scratch the hob when moving saucepans Consequently remove any dirt from the cooking surface immediately Changes in colour do not affect the functioning and stability of the glass ceramic These are not alterations to the material of the hob but just residues which have not been removed and have then carbonised Shiny surfaces can form due to the bases of saucepans especially aluminium ones rubbing on the surface and due to the use of unsuitable detergents These are difficult to remove with standard cleaning products It may be necessary to repeat the cleaning process several times Using aggressive detergents or friction with the base of Saucepans can wear away the decoration on the hob over time and contribute to the formation of dark marks 7 2 Weekly cleaning Clean and maintain the hob once a week using a standard glass ceramic cleaning product Always follow the manufacturer s instructions The silicon in these products creates a protective water repellent membrane which also resists dirt All marks stay on the membrane and can therefore be easily removed After cleaning dry the surface with a clean cloth Make sure that there is no detergent left on the cooking surface as it will undergo an aggressive reaction when heated up and could modify the structure of the cooking surface 49 GB IE Ins
Download Pdf Manuals
Related Search