Miele DA 5320 W
Contents
1. Operation To switch the fan on Automatic switch off of the Intensive setting You can set the Intensive setting so that D it only runs for 10 minutes before reverting automatically to level Ill m Press the On Off control m Tosetthis option both the fan and The fan runs at power level Il the hob lighting must be switched off The indicator lamp will come on If the cooker hood has been DAS ee connected to a window contact switch via the DSM 400 control module then the fan cannot be switched on if the window is shut The indicator lamp will flash m Press the run on option control for approximately 10 seconds The first fan setting indicator will light up m hen press in turn the hob lighting control To select a power level eeeoe m Use the controls to select the power level required e e control higher setting control lower setting I the control and Depending on the intensity of cooking vapours levels I to III green indicator lamps are usually sufficient 3 8 for normal cooking ms Intensive setting the hob lighting control again When frying or cooking food with a strong aroma you may wish to select the Intensive setting level IV yellow indicator lamp for a short period 14 Operation 0000 The indicator lamps for fan power levels and IV will flash if the automatic swit2. Changing a halogen lamp m Before any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that itis switched off at the isolator or it is switched off at the wall socket and the plug is withdrawn or the fuse from the fused spur connection unit is withdrawn or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable N Exercise caution when changing halogen lamps They get very hot during use and remain hot for some time after being switched off Let them cool down before you change them Do not touch the surface directly when changing a lamp as grease particles from your fingers will adhere to the surface and damage it Please follow the manufacturer s instructions 22 dai2328 dai2329 m To access the halogen lamp push the lamp cover gently upwards The cover will open and can be pulled down m Pull the old halogen lamp out of the connection socket and replace it with a new one 20 W G 4 cap m Push the cover back up and make sure it clicks into place After Sales Service In the event of a fault which you cannot correct yourself or if the appliance is under guarantee please contact Your Miele Dealer Chartered Agent or The Miele Customer Contact Centre see back cover for address When contacting your Dealer or Miele please quote the model and ser
3. The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P gt For safety reasons this appliance may only be used when it has been fully installed P Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults P Installation maintenance and repairs may only be carried out by a Miele authorised person in accordance with current national and local safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work P Faulty components must only be replaced by genuine Miele original parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used P
4. height of the person who will be using the hood most often The person should have sufficient space to work comfortably at the hob and also be able to reach the hood controls with ease If positioned too high extraction will be inefficient If you want the top of the cooker hood to be mounted flush with the ceiling make sure there is adequate space below it for working See maximum minimum appliance height 25 Installation Assembly parts Installation 3 protective sheets for use when fitting the tower 2 2 hose clips for securing the exhaust ducting 3 Telescopic wall bracket for securing the cooker hood to the wall Installation instructions Gees 6 screws 5 x 40 mm and 6 x S 8 plugs for securing the bracket to the wall The screws and plugs are designed for use in solid walls only For other types of wall construction alternative fixings will be required Make sure that the wall is able to take the weight of the cooker hood 2xM 6 self tapping nuts for securing the appliance Om 2 screws 3 9 x 7 5 mm for securing the tower ISS 1 hexagonal Allen key for adjusting the height of the appliance lt gt Il 1 lever for dismantling the tower 27 Installation Before installation it is important to read the information given on the following pages as well as the Appliance dimensions and the Warning and Safe
5. During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply It is only completely isolated from the electricity supply when itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the mains fuse is disconnected or itis switched off at the wall socket and the plug withdrawn or the fuse from the fused spur connection unit is withdrawn Warning and Safety instructions P Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating P This appliance may only be used in mobile installations such as ships caravans aircraft etc if a risk assessment of the installation has been carried out by a suitably qualified engineer P In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Using at the same time as other heating appliances that depend on the air from the room Warning danger of toxic fumes P Great care should be taken when using the cooker ho
6. To avoid the danger of fire do not flamb or grill over an open flame under the cooker hood When switched on the cooker hood could draw flames into the filter Fat particles drawn into the cooker hood present a fire hazard P When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time Regulate the flame so that it does not burn up the sides of the pan Do not allow the pans to overheat excessively e g when using a wok The cooker hood can become damaged when exposed to excessive heat P Always switch the cooker hood on when a cooking zone is in use otherwise condensation may collect in the hood which could cause corrosion P When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling Overheated oil and fat can ignite and could set the cooker hood on fire P Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation P The filters should be regularly cleaned or changed as appropriate Saturated filters are a fire hazard See Cleaning and care P Do not use a steam cleaner to clean this appliance Pressurised steam could reach the electrical components and cause a short circuit Corre
7. compliance with these Warning and Safety instructions Guide to the appliance wa i X d N N SS Guide to the appliance Telescopic extension piece 2 Tower Canopy Grease filters Decor panels Miele DDW 53x0 optional accessory 3 panels are required for the DA 5390 W and 4 panels for the DA 5320 W Control panel Hob lighting Touch control for the hob lighting This control switches the lighting on and off and is also a dimmer switch On Off touch control for the fan Controls to select fan power level 43 Touch control for the run on option To activate the run on option The fan can be set to continue running and to switch off automatically after either 5 or 15 minutes 42 Touch control for the grease filters The indicator lamp for the grease filters lights up when the grease filters need to be cleaned The touch control is used to reset the operating hours counter every time the grease filters are cleaned see Cleaning and care It can also be used to check and alter the operating hours counter For information about using the appliance see Operation Mode of operation The cooker hood works with air extraction quw The air is drawn in and cleaned by the grease filters and directed outside The cooker hood is fitted with a non return flap which is closed when the cooker hood is sw
8. essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person Warning and Safety instructions This appliance complies with all relevant local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on the safety installation use and maintenance of the appliance Keep these instructions in a safe place and ensure that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application P This appliance is intended for domestic use only Any other usage is at the owner s risk and could be dangerous The manufacturer cannot be held liable for damage resulting from incorrect or improper use or operation P This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whi
9. hood S 25 Installation 26 Assembly Darts x sd eie tee eR CES Gee lo Se UR be rede te ate 26 instalation INSTRUGHONS uode Roe den eee Xe ee oc RU bach tera tee 28 Protective IOI 6058400 cod eode Ee dH oed dod ede vdd Pe Pedo deed 28 DISIMAMEMING PTT 28 Electrical connection 29 Operation with Control module DSM 400 30 Connection to a window contact switch 30 Potential free connection 30 Connection to a light switch i 31 Connection for air extraction 32 Technicalidata so knees ERR tst ad EE WA cA UR ne ae 34 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Dispose of or recycle all packaging materials safely as soon as possible Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however
10. hood fan is switched on It is important to ensure that the fan power is sufficient and that the air intake has a suitable cross sectional diameter If a sufficient air intake cannot be guaranteed then the potential free contact will enable a heating appliance which depends on air in the same room as a cooker hood to be switched off when the cooker hood is in operation See also Warning and Safety instructions Operation with Control module DSM 400 Connection to a light switch The control module can be used to Switch on the cooker hood lighting and also to dim it depending on model via a light switch in the house Installation dai2151a The tower needs to be removed before the control module can be fitted to the fan unit The control module is supplied with its own detailed operating and installation instructions 31 Connection for air extraction Important To avoid the danger of toxic fumes please observe the Warning and Safety instructions This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room The cooker hood should be installed according to local and national building regulations Seek approval from the building inspector where necessary All ducting pipework and fittings must be of non flammable materials The exhaust ducting should be as short and straight a
11. 8 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 4209 CE M Nr 07 260 270 03
12. Miele Operating and installation instructions Cooker hood DA 5390 W DA 5320 W To avoid the risk of accidents ene GB AU NZ or damage to this appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 260 270 Contents Caringfortheenvironment 3 Warning and Safety instructions 4 Guide to the appliance 10 Mode of operation 12 Miele home 0 0 00 eee eee 13 eon ECCE 13 Operation pi GA ERE PR RA Dax E Le ane ded m xke 14 Toswitch thedati OE x usce etc te atate ea oer e Ra dete 14 To selecta power level sa iut ex ah athe RD e RC eit P c ei pate de 14 le ele le WEE 15 To switch thesfan IA tetro settore EE 15 To switch the hob lighting op see e t eee nes 16 To dimithe hob lighting ssepe Pe e ee Eee en 16 To switch the hob lighting oft 16 Filter operating hours counter iiisi awa 17 Cleaning and care 19 POUSO EE 19 Grease tls x ced yan Sq oder Dea Rcs OR aot as en Hacen ed x 20 Ghangingra halogen lamp issu sce pede VA E o Rue Re dom d 22 After Sales Service 23 Appliancedimensions 24 Safety distance between hob and cooker
13. arried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The connection data is given on the data plate This is visible when the grease filters have been removed Ensure that this data matches the household mains supply If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Contact a qualified electrician for advice Important This appliance is supplied for connection to an a c 230 V single phase 50 Hz supply The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60335 29 Operation with Control module DSM 400 The Miele DSM 400 Control module can be used to combine the cooker hood with other components It enabl
14. ch off for the Intensive setting is not activated m Press the control to activate the automatic switch off The indicator lamps for fan power levels and IV will now light up constantly Press the control to deactivate the automatic switch off function m Press the run on option control to confirm your selection If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting Run on option It is advisable to leave the fan running for a few minutes after cooking has finished to neutralise any lingering odours in the air The fan can be set to switch off automatically after either 5 or 15 minutes DAI eo m After cooking has finished press the run on option control whilst the fan is still running Press once The fan will switch off after 5 minutes left hand indicator lamp Press twice The fan will switch off after 15 minutes right hand indicator lamp To switch off the run on option press the run on option control again The appliance will then not switch off automatically To switch the fan off m Press the On Off control to switch the fan off The indicator lamp will go out Operation To switch the hob lighting on The hob lighting can be switched on and off independently of the fan Safety cut out Should the cooker hood be left on the fan will switch off automatically after 10 hours The lighting wi
15. ct installation P Refer to the cooker or hob manufacturer s instructions as to whether a cooker hood may be operated above the cooker hob P The minimum safety distances between the top of the cooker or hob and the bottom of the cooker hood given in the Appliance dimensions section of this booklet must be maintained unless the hob manufacturer states that a greater safety distance is required If more than one appliance is fitted beneath the cooker hood and they have different minimum safety distances to the cooker hood select the greater distance Warning and Safety instructions P Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves P All ducting pipework and fittings must be of non flammable material These can be obtained from the Miele Spare Parts department or from builders merchants P The appliance must not be connected to a chimney or vent flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes seek professional advice Accessories P Only use genuine Miele spare parts and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability The manufacturer cannot be held liable for damage caused by non
16. es the following Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same room then the control module can be used to connect a window contact switch not supplied to the appliance Once connnected the cooker hood can only be operated when the window is sufficiently open see also Warning and Safety instructions When the window is closed the cooker hood fan cannot be switched on The indicator lamp for the On Off touch control on the cooker hood will flash The cooker hood lighting is not affected by this Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain 30 If the control module is disconnected in order to operate the cooker hood without the window contact switch e g after moving house the cooker hood electronics must be reset by a Miele service technician Potential free connection This enables an external appliance to be controlled according to the switch setting on the cooker hood fan For instance it can be used to ensure a sufficient supply of fresh air when the cooker hood and a heating appliance which also depends on the air in the room are being used together by switching on an air intake fan or opening a motorised inlet flap as soon as the cooker
17. hing up liquid applied with a well wrung out soft sponge or cloth m Wipe the surfaces dry using a soft cloth Do not use too much water when cleaning the controls Water could penetrate into the electronics and cause damage Do not use cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents These will damage the surface material Important for appliances with stainless steel housing This infomation does not apply to the controls Stainless steel surfaces can be cleaned using the Miele E Cloth or with a proprietary non abrasive cleaning agent designed specifically for use on stainless steel To help prevent re soiling a conditioning agent for stainless steel can also be used Follow the manufacturer s instructions on the packaging Cleaning and care Important for appliances with lacquered housing special order finish It is very difficult to clean this type of surface without causing minor marks to the surface material This can become particularly noticeable with darker colours and if there is halogen lighting in the kitchen Controls The controls may suffer discolouration or damage if soiling is left on them for too long Remove soiling straight away Observe the General notes on cleaning earlie
18. ial number of your appliance These are shown on the data plate which is visible when the grease filter is removed For G B Please note that telephone calls may be monitored and recorded for training purposes 23 Appliance dimensions 7 29 E amp AN hb i 2 SST Sal aes Gao Sey e L NX x X NN Nu o ahi Ex SSN Appliance dimensions The shaded areas 1 and 2 represent the wall or ceiling area for the vent cut out for feeding the connection cable through to an external fan and for fitting the connection socket Connection for air extraction 200 mm Safety distance between hob and cooker hood S When planning the installation height of your cooker hood the minimum safety distance between the top of a cooker or hob and the bottom of the cooker hood are as follows unless a greater distance is specified by the manufacturer of your cooking appliance 450 mm GB 600 mm AU NZ above electric hobs and cookers 650 mm above an open grill or deep fat fryer 650 mm above gas hobs and cookers If this cooker hood is installed above a Miele Wok CS 1028 CombiSet appliance a minimum safety distance of 760 mm must be maintained between the burner and the lower edge of the cooker hood See Warning and Safety instructions for further information Account should also be taken of the
19. ient to ensure safe ventilation NThe overall ventilation condition of the dwelling must be taken into account If in doubt the advice of a competent builder or for gas a qualified gas fitter Corgi registered in the UK must be sought One of the following technical measures may be necessary to ensure safe operation f the only way of ensuring adequate ventilation is via an open window a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently A window contact switch kit is available from good builders merchants Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain The cooker hood can be set up to automatically switch on an air intake fan or open a motorised inlet flap when it is switched on The cooker hood can be set up to automatically switch off a heating appliance which also depends on the air from the room when it is switched on The Miele DSM 400 control module offers the possibility of combining other components with the cooker hood see Operation with Control module DSM 400 It is available to purchase as an optional extra If in any doubt the advice of a qualified builder gas fitter Corgi registered in the UK or electrician must be sought Warning and Safety instructions Correct use P Never use an open flame beneath the cooker hood
20. itched off No exchange of room and outside air can take place When the cooker hood is switched on the non return flap opens for the cooking vapours to be blown directly outside 12 Miele home Con ctivity This cooker hood is communication enabled Communication module XKM 2000 DA CD available as an optional extra enables the operation of the cooker hood to be automatically controlled by the operating status of a Miele electric hob with onset controls For communication to take place the hob must be fitted with communication module XKM 2000 KM 2 The hob transmits information about its operating status to the cooker hood via the household power supply Powerline When the hob is switched on the cooker hood lights and the fan also comes on During cooking the cooker hood automatically sets its power level according to the number of cooking zones in operation and their power levels After switching the hob off the fan and the hob lighting will switch off automatically after a period of time For detailed information about this function please read the separate instruction booklet supplied with the XKM 2000 DA communication module The communication module is fitted to the cooker hood in the area of the motor and is connected to the controls of the cooker hood This module must be installed by a Miele service technician or suitably qualified electrician
21. k Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk Internet www miele hk India Miele Appliances India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Ireland Miele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Il Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa iele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 54
22. ll remain on Ze O D e m Briefly press the hob lighting control to switch on the hob lighting m Pressing the On Off control will The indicator lamp will come on SEET OT The lighting will switch on at maximum brightness To dim the hob lighting The brightness of the lighting can be adjusted m With the lighting switched on press and hold the hob lighting control in The brightness will gradually dim until you release the control m Press the control in again to increase the brightness to the level required and then release it If you keep the control pressed in the light will continually change between bright and dim To switch the hob lighting off m Briefly press the hob lighting control to switch the lighting off The indicator lamp will go out 16 Operation Filter operating hours counter The number of hours the appliance has been in operation is stored in memory The operating hours counter tells you when the grease filters need to be cleaned Resetting the operating hours counter for the grease filters NEN After 30 hours of operation or another time if the operating hours counter has been altered the grease filter indicator lamp will light up The grease filters must then be cleaned Afterwards the filter operating hours counter must be reset m o do this press and hold the grease filter control in for approximately 3 seconds while the fan is switched
23. lst using it or have been given instruction concerning its use by a person responsible for their safety Safety with children P This appliance is only intended for use by adults who have read these instructions P This appliance is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or to use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen P Older children may use the cooker hood only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse P Please be aware that on cooker hoods with halogen lighting the lamps will get very hot during use and remain hot for some time after switching off To safeguard against burning keep children well away from the lamps at all times Technical safety P Before installation check the cooker hood for visible signs of damage Under no circumstances should you use a damaged appliance A damaged appliance is dangerous Warning and Safety instructions P Before connecting the appliance to the mains supply make sure that the voltage and frequency details given on the data plate correspond with the on site electricity supply see After Sales Service If they do not correspond the appliance could suffer damage Consult a qualified electrician if in any doubt P
24. od at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance may be starved of oxygen impairing combustion Harmful gases could be drawn out of the chimney or extraction ducting back into the room with potentially fatal consequences Warning and Safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously an underpressure of 0 04 mbar 4 pa is the maximum permissible in the room dai1477 Ventilation can be maintained by air inlets which must not be blocked in windows doors and outside wall vents Or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa A ventilation brick alone is not generally suffic
25. on The indicator lamp for the control will go out Reading the filter operating hours counter To check the percentage of time set already used mom m Press the On Off control to switch the fan on m Press and hold the grease filter control 0000 One or more of the indicator lamps for the controls will flash The number of flashing lamps shows the percentage of the operating time which has already been used up tlamp 25 2lamps 50 3lamps 75 4lamps 100 The number of operating hours used remains in the memory even when the appliance is switched off or there is a power cut Operation Altering the filter operating hours counter The filter operating hours counter is set at 30 hours This can be lengthened or shortened to suit the type of cooking you do You can choose 20 30 40 or 50 hours Select a short time if you roast or fry a lot If you use very little fat for cooking select a longer time If you only cook occasionally we recommend that you still select a short time because grease which has built up gradually over a long period of time will harden on the grease filters and make cleaning more difficult m Press the On Off control to switch the fan off m Press the run on option control and the grease filter control at the same time The indicator lamp for the grease filter control and one of the indica
26. oven sprays Cleaning the grease filters in the dishwasher m Place the filters as upright as possible in the lower basket with the short sides upright and wash on a 65 C programme ensuring the spray arm is not obstructed If a Miele dishwasher is being used select the Sensor wash programme m Use a mild dishwasher detergent Depending on the cleaning agent used cleaning the filters in a dishwasher can cause permanent discolouration to the surface However this will not affect the functioning of the filters in any way m After cleaning leave the filters to dry on an absorbent surface before replacing them When removing the filters for cleaning also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire When putting the grease filters back in position ensure that the locking clips are facing down towards the hob UT dai1619 If a grease filter is inadvertently replaced upside down insert a small screwdriver blade into the slit to disengage the clip m After replacing the grease filters press the grease filter control for approximately 3 seconds to reset the operating hours counter The indicator lamp will go out If the grease filters are cleaned before the operating hours counter has reached its maximum the grease filter control should be pressed for approximately 6 seconds to reset the counter 21 Cleaning and care
27. r exhaust ducting with a diameter of 200 mm the following accessories are required CH lt L Exhaust hose DAS 200 Exhaust grille DFG 200 for mounting on the external wall Lead flashing Roof ducting DDF 200 for mounting on a sloping tiled roof Reducing oollar for the exhaust stub if using exhaust ducting with a 150 mm diameter 33 Technical data Total connected load DA5390W 580 W DA D OOW awowis 600 W FON a4 ds doce pa dia 500W Hob lighting DA 5390 W 4x 20W DA5320W 5x20W VONAGE suut diea an hem ess 230 V Fregueneyz aa xe ace oed 50 Hz FuseratingGB 13A AUS NZ Plug rating liess 10A Test marks Electrical safety EE C Tick Mark Electrical cable length 1 5m Fan performance Extraction power according to EN 61591 Extraction system 2 200 mm Levell 350 m3 h WI 600 m h Level 850 m3 h Level IV Intensive Setting 1 300 m h Extraction system 2 150 mm Kee geg Boegen Beer da an 300 m h RI WEE HE 500 m h Level IM oss sss Rem 700 m3 h Level IV Intensive Setting 1 000 m h Unrestricted 1 450 m3 h 34 35 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co u
28. r in this section Do not use stainless steel cleaning agents on the controls Grease filters The re usable metal grease filters in the appliance remove solid particles grease dust etc from the kitchen vapours preventing soiling of the cooker hood o To avoid a build up of grease the grease filters should be cleaned regularly at least every 3 4 weeks but always clean immediately the grease filter indicator lamp comes on 20 An oversaturated filter is a fire hazard If decor panels are fitted as an optional extra these need to be removed first dai2120 m To do this disengage them from their catches m See the notes under Housing for how to clean the decor panels Like the grease filters they can be cleaned in the dishwasher dai2121 m To take out the grease filters release the locking clip on the filter lower the filter 457 unhook it at the back and remove it To avoid damaging the filters or the hob below make sure you hold the filters securely at all times when handling them Cleaning and care Cleaning the grease filters by hand m Clean the filters with a soft nylon brush in a mild solution of hot water and a small amount of washing up liquid Do not use undiluted washing up liquid Do not use cleaning agents containing descaling agents powder cleaners cream cleaners or abrasive all purpose cleaning agents
29. s possible To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 200 mm If exhaust ducting with a diameter of less than 200 mm or if flat ducting is used the noise level of the cooker hood will increase and extraction will be less efficient Only reduce the diameter of the ducting if absolutely necessary e g where narrower ducting has already been installed Only use wide radius bends Tight bends reduce the air throughput of the cooker hood Only use smooth pipes or flexible hoses made from non flammable materials for extraction connection 32 If the exhaust ducting is secured to the exhaust stub by a hose clip ensure that it is fitted correctly and is not askew Do not overtighten Otherwise the exhaust stub could buckle and the non return flap could become jammed 2 E s E E Ss When ducting is horizontal it must be laid to slope away at at least 1 cm per metre to ensure no condensate drains into the appliance f the exhaust air is to be ducted into a vent flue the ducting must be directed in the flow direction of the flue Important If the exhaust ducting is to run through rooms ceiling space etc where there may be great variations in temperature between the different areas the problem of condensation will need to be addressed The exhaust ducting will need to be suitably insulated Connection for air extraction Fo
30. tor lamps will flash 18 0000 The indicator lamps show the time which has been set 1st lamp from the left 20 hours 2nd lamp from the left 30 hours 3rd lamp from the left 40 hours 4th lamp from the left 50 hours m Use the controls to select the desired time EES m Confirm the selection by pressing the grease filter control All the indicator lamps will go out If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting Cleaning and care Before any cleaning or maintenance work is carried out disconnect the cooker hood from the mains supply Ensure that itis switched off at the isolator or itis switched off at the wall socket and the plug removed or the fuse from the fused spur connection unit is withdrawn or the mains fuse is withdrawn or the screw out fuse is removed in countries where this is applicable A range of Miele branded cleaning and conditioning agents are available to order through your Miele Dealer Chartered Agent the Miele Spare Parts Department or via the internet on www miele shop com Housing General notes The surfaces and controls are susceptible to scratches and abrasions Please observe the following cleaning instructions m All external surfaces and controls can be cleaned using a Miele E Cloth or with warm water and a small amount of was
31. ty instructions at the beginning of this book This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on air from the same room as this could result in the build up of toxic fumes Installation instructions See enclosed Installation sheet for instructions on how to install this appliance Protective foil on stainless steel appliances The housing components have protective foil around them to prevent them being damaged during transport Please remove this foil before fitting the housing components It can be peeled off easily 28 Dismantling Should the appliance ever need to be dismantled follow the installation instructions in reverse order as described on the installation sheet A lever is supplied to assist with the removal of the tower pa m After loosening the fixing screws on the tower push the lever between the tower and the extension piece to lever the tower out of its fixings dai0920 Electrical connection All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been c
Download Pdf Manuals
Related Search