Longshine LCS-C862 network media converter
Contents
1. 10 100 1000T to 1000SX LX SFP Media Converter Gigabit Triple speed Converter User s Manual December 2006 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER COPYRIGHT All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means whether electronic mechanical photo copying recording or otherwise without the prior written permission of the publisher fae FCC WARNING fE This equipment has been tested and found to comply with the limits for a class A device pursuant to part 15 of FCC rules These limits are designed to provide reasonable protection against harmful interference in a commercial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communication Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense CE This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Take special care to read and understand all the content in the warning boxes A Be vmo 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER TABLE OF CONTENTS J 2 ABOUT THIS GUIDE serennog S WSC OM2. ER 2 Hardware Description 2 1 Product Overview The 10 100 1000Base T to 1000Base SX LX SFP Media Converter is primarily designed for larger workgroups which demand higher speed and broader bandwidth and requires migration and expansion from copper based Gigabit triple speed to Fiber based Gigabit networks lt features an automatic MDI MDI X on the RJ 45 port that allows for direct connection to a workstation switch or hub Now the network manager does not need to worry about the cable configuration crossover or straight through when establishing connection between RJ 45 ports It features both an RJ 45 jack and an SFP slot which allows it to easily integrate a 1000Base T network with a 1000Base SX LX fiber network If the LFS DIP switch is set to ON the Link Fault Signaling function is enabled If the copper link is down the fiber port will be disabled by the Converter If the fiber port loses signal the copper port will be disabled by the Converter These two types of disabling actions will enable the spanning tree protocols of the neighboring switch to go into effect The Media converter is specifically designed to offer fiber advantages for mission critical networks like Telco ISP backbones cable operators banking and enterprise networks It can reduce network downtime and increase Quality of Service levels 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 2 2 Product Illustrations Front Pane LEDs Ethernet Port Fibe
3. LX SFP MEDIA CONVERTER 1 5 Specifications Standards Connectors Max Distance Cable Data Rates Unit LED DIP Switches Power Environment Emissions Dimensions IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3ab 1000Base T IEEE 802 3z 1000Base SX LX 1x RJ 45 1x Fiber SFP UTP 100m Cat 5 5e 6 Fiber Optic SFP up to 500m multi mode 110km single mode Multi mode fiber optic 50 125 or 62 5 125um Single mode fiber optic 9 125um Copper Cat 5 5E 6 Fiber 1000 Mbps Copper 10 100 1000Mbps PWR Illuminated for normal operation ALM Illuminated when failure occurs on fiber or copper link LNK ACT Illuminated when receiving link pulses from compliant Fiber link devices Flashing when data packets being transmitted or received via fiber port DIP 1 LFS Enable disable Link Fault Signaling LFS 12V DC 0 8A external power supply adapter Frequency 50Hz to 60Hz Operating 0 C to 50 C 10 to 90 non condensing 20 C to 70 C 5 to 90 non condensing Temperature Relative Humidity Storage Relative Humidity FCC Part 15 of Class A amp CE approved 110 x 74 x 23 4mm L x W x H 1 6 Package Contents The package should include the following One Converter unit One power adapter please check connector type and input power specification Four self adhesive pads User s Manual 10 100 1000T TO 1000SX LX SFP MEDIA CONVERT
4. O a tent PU DOSO ia r E EEEE E REE EEEE E EERE Terme WS AG Cicer ies ste oe hae eae E EEEE FC AUC EIEE A E EART E A EE E TE EE OPECINCANON S srsccenconsndesatasdiactaatianesancioduiacdintonsadiaamteadiameanecauie PACKAGES COMENS sannara R h ee ee ee ee 0O U A wN HARDWARE DESCRIPTION cccecceeeeeeeeeeeeeeeeeeeeeeeesaeneees 2 1 Product OVEIVICW cccccececccccceccccccececccceccaecceueacsceneacsneneavens 2 2 Product lllustrations ccccccccccececcccececccccceccacececeacsceueaceueaeas 2 93 DIP Switches eset eerie iets arisen ei ieninnebie hi pemenien biannual EE INGO Fi sey tot uanstet sane ote une te lent eaeenstseetet a iocenetaieee aa aina INSTAECEA TION ees E Al LOCaUO M eiaa a 4 2 10 100 1000Base T Port RU 45 cc eecccseeeeeeeeeeeeeeeseeeeneees 43 SGIGADICSEP SOU cscssscosscassssseusvadansusvetondesotsncusvedensusvetensuenstencusyes 44 Link Fault SonalNg isiin aa a 4 5 Desktop Installation wssiwsscvadsvalaneianed saadearavavewwscuadevuscnadedeteavecseaed 4 6 Powering On the Unit ccccccsececseeeeceeeeeeeeeeeeeeseeesseeesaeees APPENDIX APPLICATION DIAGRAMS Ht ADDICION DAG AT N sasie EEEE vont pictyeti2e 5 2 ADPIC DAG AN I secre APPENDIX MINI CONVERTER CHASSIS 6 1 Mini Converter GNaSSiS sasaina naa 02 iF CaluleSuiati Aiden a N 69 AMX RACK Oto reiia 6 4 Installing the Converte secsi 6 5 Rear view of Chassis and Specifications cccccsee
5. echnical Specifications for the acceptable temperature and humidity operating environments 2 Install the Converter in a location free from strong electromagnetic field generators such as motors vibration dust and direct exposure to sunlight Leave at least 10cm of space at the front and rear of the unit for ventilation Affix the provided rubber pads to the bottom of the Converter for grip and to protect the case from scratching 4 2 10 100 1000Base T Port RJ 45 The auto MDI MDI X and auto negotiation on the RJ 45 port alleviates the worry of cabling configuration when connecting the Converter with a 10 100 1000Base T device It accepts both straight through and cross over Ethernet cables without the need to re configure the port Whether connecting to a switch LAN card or other network device via the RJ 45 port simply plug and go 4 3 Gigabit SFP Slot To connect a fiber cable s connector to the Converters SFP slot slide the selected SFP module mini GBIC into the SFP slot making sure that the module s receptors line up with the receptors at the back of the slot Push until you hear a click Once the module is inserted correctly take the cable connector and turn it so that it will fit into the mouth of the module Then push the connector into the mouth until its catches click into the receiving grooves in the module s mouth Use the appropriate type of multi mode or single mode fiber depending on the SFP m
6. eeeneeeeeeees 6 5 1 Rear View of Chassis with AC Power Supply 0 6 5 2 Rear View of Chassis with DC Power Supply 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 1 About This Guide 1 1 Welcome Thank you for choosing this 10 100 1000Base T to 1000Base SX LX SFP Media Converter This device integrates Gigabit Ethernet triple soeed copper segments and Gigabit fiber segments in a highly flexible package 1 2 Purpose This guide discusses how to install and configure your 10 100 1000Base T to 1000Base SX LX SFP Media Converter 1 3 Terms Usage In this guide the term Converter first letter upper case refers to your 10 100 1000Base T to 1000Base SX LX SFP Media Converter and converter first letter lower case refers to other converters 1 4 Features Standards IEEE 10 100Base TX o IEEE 802 3ab 1000Base T IEEE 802 3z 1000Base SX LX Interface e One 10 100 1000 Mbps Ethernet port e Auto MDI MDI X support on RJ 45 port e One SFP slot for Gigabit Ethernet link e Extends distances up to 500m 1 650ft for multi mode fiber module 110km 317 625ft for single mode fiber module depends on SFP Management e Alarm LED illuminates to indicate link failure e Status LEDs for easy monitoring of device s status Mechanical amp Environmental e External power supply e Chassis compliant internal power supply e FCC Class A amp CE approved 10 100 1000T TO 1000SX
7. odule being used The fiber optics transmit data at up to 1000Mbps and can maintain data integrity over cable distances as long as 60km depending on the selected SFP mini GBIC module Warning Because invisible laser radiation may be emitted from the aperture of the fiber port when no cable is connected avoid exposure to laser radiation and do not stare into the open apertures 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 4 4 Link Fault Signaling LFS is an important function that is extremely beneficial in terms of network status monitoring The LFS function monitors both the copper and fiber segments to ensure that the STP can kick in the moment a link failure occurs on either segment Set LFS to ON for normal operations Set LFS to OFF when installing cables or when testing the network connection Note The LFS feature influences both fiber and copper segments When disruption occurs on the copper segment the fiber segment will be disabled When the fiber segment loses signal the copper segment will be disabled To utilize the full benefits of LFS four converters can be used to build a primary and a secondary path between two switches The switches must support Spanning Tree or Fast Spanning Tree protocols By default transmission of data will travel via the primary path If a link failure is detected transmission will automatically be switched to the secondary path by Spanning Tree Protocol delivering non stop network connecti
8. r SFP Slot Rear Panel Power LED DIP Switches Power Connector 2 3 DIP Switches 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 3 LED Indicators This Device has LED indicators located at the front of the device The LEDs have been designed to give easy at a glance network status and provide real time connectivity information Please see below for an interpretation of their functions LED Indicators LED Condition Status PWR On Green Unit is receiving power Off Power off or failure LNK ACT On Green Fiber link up Flashing Green Data packets being transmitted or received via Fiber port Off Fiber link down 1000 On Green 1000 Base Mode Off 10 100 Base Mode Port On Green Copper link up LNK ACT Flashing Green Data packets being transmitted or received via Ethernet port ALM On Red Any link failure or LFS 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 4 Installation In this chapter we will take a look at how to install the Converter within its operating environment To install your Media Converter please see the following procedures e Location e 10 100 1000Base T port e Gigabit SFP slot e Link Fault Signaling e Desktop installation e Powering on unit 4 1 Location The location selected for installing the Converter may greatly affect its performance When selecting a site we recommend considering the following rules 1 Install the Converter in a fairly cool and dry place See T
9. the Converter so that it fits between the upper and lower guide rails Warning A Always erste that the converter power socket is positioned at the base of the Chassis Never force the Converter into the Chassis check power socket position and alignment 6 5 6 5 1 Rear View of Chassis with AC Power Supply Power 100 240V AC Optional 12V Adapter Dimensions 109 x 174 x 44 3 mm Lx Wx H 6 5 2 Rear View of Chassis with DC Power Supply Power 48V DC Optional 12V Adapter Dimensions 109 x 174 x 44 3 mm L x W x H 10
10. the figure below the Converter is functioning as a high speed bridge between switches creating increased capacity for each user node on the local area network It is providing a 10 100 1000Mbps full duplex link to a variety of Fast Ethernet or Gigabit network devices within a LAN Switch CONVERTER lt CONVERTER Switch Gigabit Ethernet Switch Gigabit Ethernet Switch Multi mode 500m Single mode up ta 110km LITP g tom UTP i Enhanced 10MO0M000T to Enhanced 10M00 000T to S 1O00S2 L4 Converter 1O000S2 L4 Converter 5 2 Application Diagram II In the figure below the Converter is functioning as a server aggregation for an enterprise or LAN configuration It is providing a 10 100 1000Mbps full duplex link to a workgroup of 10 100 1000 switches located on separate floors within a single building Switch gt CONVERTER CONVERTER lt Server Gigabit Ethernet Switch Multi mode 500m Single mode up ta 110km LITP Seryer g 1000M LITP a Enhanced 10M00000T to Enhanced 104 00000T to TOISAALLA Convener TOISAALLA Convener 1000M TENEH 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 6 Appendix Mini Converter Chassis 6 1 Mini Converter Chassis The Chassis is developed to accommodate just one media converter The Chassis provides AC or DC power protection for converter units Now network designers can plan their Ethernet Fast Ethernet ATM or Gigabit networks without ha
11. ving to worry about the power source Also its uniquely compact size allows it to be installed in locations where space is limited 6 2 Features e Simple and easy to install e Adds fiber connectivity to otherwise copper based networks e Supports 10 100 1000Base T copper fiber single multi mode ST SC MT RJ VF 45 LC WDM connector converters e Supports one media converter e Suitable for networks of all sizes in all locations e Provides internal AC and DC switching power supply e Made from high quality durable steel e Optional external redundant power adapter 6 3 Affixing Brackets We have supplied 2 special brackets that easily attaches to the Converter This allows for the secure placement of the Converter into the Chassis It also seals off the front of Chassis and allows it to function correctly Step 1 Using a Phillips screwdriver remove two screws from the side panels on the converter Step 2 Place the converter and brackets on a flat horizontal surface as illustrated above Secure the brackets by replacing the screws Ensure that the rails are flush with the underside of the Converter The Converter is now ready for loading into the Chassis 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 6 4 Installing the Converter in the Chassis Once the Converter has been attached to the bracket it can be installed into the Chassis Special care must be taken to ensure the correct mating of the power connector Align
12. vity 4 5 Desktop Installation Follow the instructions listed below to install the Converter in a desktop location 1 Locate the Converter in a clean flat and safe position that has easy access to AC power Affix the four 4 self adhesive rubber pads to the underside of the Converter Apply AC power to the Converter The green PWR LED on the rear panel should light 4 Connect cables from the network partner devices to the ports on the front panel The green LNK LED on the front panel associated with the port should light This converter can also be mounted on a vertical surface Warning Please exercise caution when using power tools Also install this unit A away from damp or wet locations or in close proximity to very hot surfaces These types of environments can have a detrimental effect on the converter and cables An ideal location is a lightly cooled place such as a typical equipment room 4 6 Powering On the Unit The Converter uses an external power supply of 9 32V DC 0 8A 50Hz to 60Hz 1 Insert the power cable plug directly into its receptacle located at the back of the device Plug the power adapter into an available socket Check the rear panel LEDs as the device is powered on to verify that the Power LED is lit If not check that the power cable is correctly and securely plugged in 10 100 1000T TO 1000SX LX SFP MEDIA CONVERTER 5 Appendix Application Diagrams 5 1 Application Diagram In
Download Pdf Manuals
Related Search