Omnitron 4384
Contents
1. 2 If desired attach the optional wall mounting brackets part number 4381 and securely fasten to desired location refer to illustration 3 Assure that the DC circuit breaker can supply 1 0A of current to the power supply 4 Locate the DC circuit breaker and switch the DC circuit breaker to the OFF position Cut the power cable to the length required Strip approximately 3 8 of an inch of insulation from the power cable wires 7 Connect the power cables to the FlexPoint DC Converter by fastening the stripped ends to the DC connector 8 Connect the power cables to the circuit breaker and switch the circuit breaker ON 9 Check the power LED on the back panel of the FlexPoint DC Converter The LED should be ON 10 Check the power LED on the front pannel of the attached FlexPoint Media Converter The LED should be ON on Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate use and or maintenance of the equipment by Buyer Buyer supplied equipment Buyer supplied interfacing unauthorized modifications or tampering with equipment including removal of equipment cover by personnel not specifically authorized and certified by Omnitron or misuse or operating outside the environmental specification of the product including but not limited to voltage ambient temperature radiation unusual dust etc or improper site preparation or maintenance No other warranty2. 325 6p 225 ped Sor w ss g Gi y 33 i S ie Q on v 5 30 3 F D aa o ot Q O 2 o fe 36 3 N 26 d 5 1 85 D z 9 3 o Q Q Q D o gt ve is o 3 e co o Q o D h o gt 2 A 4 o S a 3 B Preparation Assure that the FlexPoint DC Converter is physically installed in accordance with the Site Preparation Requirements outlined earlier in this document Sip E Cabling and Power Up WARNING Note the wire colors used for making the positive negative and ground connections Use the same color assignment for the connection at the circuit breaker WARNING REGARDING EARTHING GROUND a This equipment shall be connected to the DC supply system earthing electrode conductor or to a bonding jumper from an earthing terminal bar or bus to which the DC supply system earthing electrode is connected b This equipment shall be located in the same immediate area such as adjacent cabinets as any other equipment that has a connection between the earthed conductor of the same DC supply circuit and the earthing conductor and also the point of earthing of the DC system The DC system shall not be earthed elsewhere c The DC supply source is to be located within the same premises as this equipment d There shall be no switching or disconnecting devices in the earthed circuit conductor between the DC source and the earthing electrode conductor Wa
3. is expressed or implied Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose Exclusive Remedies The remedies provided herein are the Buyer s sole and exclusive remedies Omnitron shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any legal theory Form 040 04384 001 11 00 Please complete both sides of this form wn o ne wn ieee a o L 2 oe i fe 9 ae 5 Es E 8 So 83 2 wE gt Do2 2 gt ne g Oc o mo FE 8 3 5E 2 g LL O O oO S525 a E oO lt q E Ds 9S roi go DESO o cHe gTr i sago o Os aA D oh DON E atsg gt 0000F cH E37 sea acwT S ESE R o x RK gt a DSONEL T D5 Dy p o E u z P 3 D Box E EES S556 og 9o83 SoeF A Zoct ood w WARNING NEVER ATTEMPT TO OPEN OR SERVICE THE POWER SUPPLY UNIT OPENING THE POWER SUPPLY UNIT MAY CAUSE SERIOUS INJURY OR DEATH LED Indicators LED Color Power Yellow Description Power applied Technical Support For help with this product contact our Tech Support Phone 949 250 6510 Fax 949 250 6514 Address Omnitron Systems Technology Inc 27 Mauchly 201 Irvine CA 92618 USA E mail support omnitron systems com URL http www omnitron systems com
4. osr Omnitron Systems Technology Inc FlexPoint DC Converter User Instructions General Description Designed for telecommunications environments such as campuses and phone centers that use DC power as a primary source The FlexPoint DC converter provides a user with the ability to power a single media converter with DC power Site Preparation Requirements 1 Power Assure the DC power can supply 1 0A of current 2 This equipment requires 18 60 VDC 1 0 Amps of power Appropriate overloading protection should be provided on all DC power source outlets utilized 3 Wiring methods used for the connection of the equipment to the primary power supply shall be in accordance with the National Electrical Code ANSI NFPA 70 and the Canadian Electrical Code Part I C22 1 WARNING Only a DC power source that complies with safety extra low voltage SLEV requirements can be connected to the DC input power supply Tools and Equipment Required Phillips head screwdriver not supplied Flat head screwdriver not supplied Wire cutter stripper not supplied Three conductor 14 AWG copper power cable recommended not supplied QO0OOFPVHET VQ O O F7 QZCOO ao 3 cx 2520 x D I o sx gt 2o v 38 532 o D DO Si nH D o v 0 x An zZ D oS 2 eo o a 3 4 g2 noj x amp o 5 0 T A a on 3g 3 TO OL dp m 5 Z 8d a a Q 2 A PER ogo 532 0 5 _ So a Sis
5. rning The operating description in this Instruction Manual is for use by qualified personnel only To avoid electrical shock do not perform any servicing of this unit other than that contained in the operating instructions unless you are qualified and certified to do so by Omnitron Systems Technology Inc Caution All user required operations can be performed without opening the unit Never attempt to open or remove the cover or tamper with the unit Warranty This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment TO REGISTER COMPLETE AND MAIL OR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS Or you may register your product on the internet at http www omnitron systems com During the warranty period Omnitron will at its option repair or replace a product which is proven to be defective For warranty service the product must be sentto an Omnitron designated facility at Buyer s expense Omnitron will pay the shipping charge to return the product to Buyer s designated US address using Omnitron s standard shipping method 1 Securely attach the FlexPoint DC Converter to a FlexPoint media converter using 4 phillips head screws refer to illustration
Download Pdf Manuals
Related Search